U-Boot 2016.05-tld-1 (Jun 12 2016 - 14:06:08 -0700) HP Thin Client T5325 SoC: Kirkwood 88F6281_A1 SPI: ready DRAM: 512 MiB WARNING: Caches not enabled SF: Detected SST25VF080B with page size 256 Bytes, erase size 64 KiB, total 1 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: SM22 Firm: I052 Ser#: (03)5526888-20080228 Type: Hard Disk Capacity: 463.6 MB = 0.4 GB (949536 x 512) Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 7911424 000d0432-01 83 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Partition Map for IDE device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type loading envs from ide 0 ... ** Invalid partition 1 ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 166 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3154896 bytes read in 360 ms (8.4 MiB/s) loading uInitrd ... 7179935 bytes read in 524 ms (13.1 MiB/s) loading DTB /boot/dts/kirkwood-t5325.dtb ... 11653 bytes read in 920 ms (11.7 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-02-19 5:55:25 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3154832 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f927000, end 0ffffe5f ... OK Loading Device Tree to 0f921000, end 0f926d84 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: HP t5325 Thin Client [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:512K(uboot),256K(sdd_firmware),64K(uboot_env),64K(permanent_uboot_env),64K(hp_env) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 503468K/524288K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 20820K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000331] Console: colour dummy device 80x30 [ 0.000362] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256) [ 0.090101] pid_max: default: 32768 minimum: 301 [ 0.090216] Security Framework initialized [ 0.090292] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090313] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091097] Initializing cgroup subsys io [ 0.091131] Initializing cgroup subsys devices [ 0.091156] Initializing cgroup subsys freezer [ 0.091189] Initializing cgroup subsys net_cls [ 0.091271] CPU: Testing write buffer coherency: ok [ 0.091723] Setting up static identity map for 0x8200 - 0x8258 [ 0.092025] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.095705] devtmpfs: initialized [ 0.100579] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.101039] prandom: seed boundary self test passed [ 0.104777] prandom: 100 self tests passed [ 0.104802] pinctrl core: initialized pinctrl subsystem [ 0.106181] NET: Registered protocol family 16 [ 0.106630] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130107] cpuidle: using governor ladder [ 0.160103] cpuidle: using governor menu [ 0.160522] Feroceon L2: Enabling L2 [ 0.160568] Feroceon L2: Cache support initialised. [ 0.160966] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.166802] No ATAGs? [ 0.201598] vgaarb: loaded [ 0.201956] usbcore: registered new interface driver usbfs [ 0.202054] usbcore: registered new interface driver hub [ 0.202120] usbcore: registered new device driver usb [ 0.203210] clocksource: Switched to clocksource orion_clocksource [ 0.258422] NET: Registered protocol family 2 [ 0.259197] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.259258] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.259310] TCP: Hash tables configured (established 4096 bind 4096) [ 0.259376] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.259400] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.259592] NET: Registered protocol family 1 [ 0.259987] RPC: Registered named UNIX socket transport module. [ 0.259999] RPC: Registered udp transport module. [ 0.260006] RPC: Registered tcp transport module. [ 0.260013] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.260289] Unpacking initramfs... [ 0.899921] Freeing initrd memory: 7012K (cf927000 - d0000000) [ 0.900047] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.901149] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.901223] audit: initializing netlink subsys (disabled) [ 0.901272] audit: type=2000 audit(0.890:1): initialized [ 0.901619] Initialise system trusted keyring [ 0.901999] zbud: loaded [ 0.902289] VFS: Disk quotas dquot_6.6.0 [ 0.902348] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.902905] NFS: Registering the id_resolver key type [ 0.902945] Key type id_resolver registered [ 0.902955] Key type id_legacy registered [ 0.902981] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.902995] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.903278] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.903823] Key type big_key registered [ 0.923921] Key type asymmetric registered [ 0.923945] Asymmetric key parser 'x509' registered [ 0.924045] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.924067] io scheduler noop registered [ 0.924083] io scheduler deadline registered [ 0.924145] io scheduler cfq registered (default) [ 0.925585] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.926279] irq: Cannot allocate irq_descs @ IRQ36, assuming pre-allocated [ 0.926702] irq: Cannot allocate irq_descs @ IRQ68, assuming pre-allocated [ 0.927537] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.927556] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.927570] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.927584] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.927991] PCI: bus0: Fast back to back transfers disabled [ 0.928017] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.928642] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none [ 0.943300] PCI: bus1: Fast back to back transfers disabled [ 0.943431] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe5ffffff] [ 0.943447] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 0.943466] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe3ffffff pref] [ 0.943486] pci 0000:01:00.0: BAR 1: assigned [mem 0xe4000000-0xe403ffff] [ 0.943503] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x1007f] [ 0.943519] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.943532] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 0.943546] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe5ffffff] [ 0.943636] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 0.943948] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.983895] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.984122] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.023891] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.024357] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.025740] console [ttyS0] disabled [ 1.025802] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 12500000) is a 16550A [ 1.740064] console [ttyS0] enabled [ 1.745513] m25p80 spi0.0: found sst25vf080b, expected m25p80 [ 1.751317] m25p80 spi0.0: sst25vf080b (1024 Kbytes) [ 1.756377] 5 cmdlinepart partitions found on MTD device spi0.0 [ 1.762322] Creating 5 MTD partitions on "spi0.0": [ 1.767163] 0x000000000000-0x000000080000 : "uboot" [ 1.773388] 0x000000080000-0x0000000c0000 : "sdd_firmware" [ 1.780135] 0x0000000c0000-0x0000000d0000 : "uboot_env" [ 1.786658] 0x0000000d0000-0x0000000e0000 : "permanent_uboot_env" [ 1.794072] 0x0000000e0000-0x0000000f0000 : "hp_env" [ 1.801328] libphy: Fixed MDIO Bus: probed [ 1.805830] libphy: orion_mdio_bus: probed [ 1.814739] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 1.894044] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address f4:ce:46:24:67:f7 [ 1.902922] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.909541] ehci-pci: EHCI PCI platform driver [ 1.914100] ehci-orion: EHCI orion driver [ 1.918308] orion-ehci f1050000.ehci: EHCI Host Controller [ 1.923872] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 1.931722] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000 [ 1.953273] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 1.959532] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.966383] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.973655] usb usb1: Product: EHCI Host Controller [ 1.978554] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 1.985216] usb usb1: SerialNumber: f1050000.ehci [ 1.990682] hub 1-0:1.0: USB hub found [ 1.994534] hub 1-0:1.0: 1 port detected [ 1.999427] mousedev: PS/2 mouse device common for all mice [ 2.005732] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 2.012806] i2c /dev entries driver [ 2.018053] hidraw: raw HID events driver (C) Jiri Kosina [ 2.023932] drop_monitor: Initializing network drop monitor service [ 2.030472] NET: Registered protocol family 17 [ 2.035237] Key type dns_resolver registered [ 2.040361] registered taskstats version 1 [ 2.044618] Loading compiled-in X.509 certificates [ 2.049498] zswap: loaded using pool lzo/zbud [ 2.062611] Key type encrypted registered [ 2.067377] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.078211] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 2.164026] systemd-udevd[84]: starting version 215 [ 2.170989] random: systemd-udevd urandom read with 3 bits of entropy available [ 2.313313] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.356075] SCSI subsystem initialized [ 2.415332] sata_mv f1080000.sata: slots 32 ports 2 [ 2.458794] scsi host0: sata_mv [ 2.473409] scsi host1: sata_mv [ 2.476872] usb 1-1: New USB device found, idVendor=0424, idProduct=2514 [ 2.488590] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.498895] ata1: SATA max UDMA/133 irq 35 [ 2.503019] ata2: SATA max UDMA/133 irq 35 [ 2.507979] hub 1-1:1.0: USB hub found [ 2.513338] hub 1-1:1.0: 4 ports detected [ 2.803241] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 3.025734] usb 1-1.1: New USB device found, idVendor=8564, idProduct=1000 [ 3.032662] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.040042] usb 1-1.1: Product: Mass Storage Device [ 3.044957] usb 1-1.1: Manufacturer: JetFlash [ 3.049335] usb 1-1.1: SerialNumber: 25UJMQ3QFISG8YMS [ 3.054458] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 3.069476] ata1.00: ATA-7: SM224, I0521, max UDMA/133 [ 3.076006] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 3.082420] ata1.00: 949536 sectors, multi 0: LBA [ 3.087898] scsi host2: usb-storage 1-1.1:1.0 [ 3.094122] usbcore: registered new interface driver usb-storage [ 3.103138] usbcore: registered new interface driver uas [ 3.108712] ata1.00: configured for UDMA/133 [ 3.123865] scsi 0:0:0:0: Direct-Access ATA SM224 1 PQ: 0 ANSI: 5 [ 3.483249] ata2: SATA link down (SStatus 0 SControl F300) [ 3.515765] sd 0:0:0:0: [sda] 949536 512-byte logical blocks: (486 MB/463 MiB) [ 3.525911] sd 0:0:0:0: [sda] Write Protect is off [ 3.530861] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.542751] sda: [ 3.546127] sd 0:0:0:0: [sda] Attached SCSI disk [ 3.555058] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 4.307703] scsi 2:0:0:0: Direct-Access JetFlash Transcend 4GB 1100 PQ: 0 ANSI: 0 CCS [ 4.319170] sd 2:0:0:0: [sdb] 7913472 512-byte logical blocks: (4.05 GB/3.77 GiB) [ 4.328972] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 4.340531] sd 2:0:0:0: [sdb] Write Protect is off [ 4.346397] sd 2:0:0:0: [sdb] No Caching mode page found [ 4.351739] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 4.363768] sdb: sdb1 [ 4.376788] sd 2:0:0:0: [sdb] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. done. Gave up waiting for root device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) ALERT! /dev/disk/by-label/rootfs does not exist. Dropping to a shell! modprobe: module i8042 not found in modules.dep [ 43.854574] uhci_hcd: USB Universal Host Controller Interface driver [ 43.871270] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 43.888658] usbcore: registered new interface driver usbhid [ 43.894456] usbhid: USB HID core driver BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs) [ 102.537465] random: nonblocking pool is initialized