Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD3200BPVT-00ZEST0 Firm: 01.01A01 Ser#: WD-WX91A41P0908 Type: Hard Disk Supports 48-bit addressing Capacity: 305245.3 MB = 298.0 GB (625142448 x 512) Device 1: Model: WDC WD20EFRX-68EUZN0 Firm: 80.00A80 Ser#: WD-WCC4MLJV65ZU Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) 2756040 bytes read in 1035 ms (2.5 MiB/s) 6032465 bytes read in 2142 ms (2.7 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2755976 Bytes = 2.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6032401 Bytes = 5.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.16.0-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #2 PREEMPT Sun Aug 31 18:56:01 PDT 2014 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: ZyXEL NSA325 2-Bay Power Media Server [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rootdelay=4 rootfstype=ext4 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) security=selinux selinux=1 audit=1 enforcing=0 [ 0.000000] audit: enabled (after initialization) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 505588K/524288K available (5441K kernel code, 397K rwdata, 1840K rodata, 257K init, 299K bss, 18700K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07248b0 (7283 kB) [ 0.000000] .init : 0xc0725000 - 0xc0765444 ( 258 kB) [ 0.000000] .data : 0xc0766000 - 0xc07c975c ( 398 kB) [ 0.000000] .bss : 0xc07c975c - 0xc08144dc ( 300 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000010] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns [ 20.594671] Console: colour dummy device 80x30 [ 20.594694] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816) [ 20.684473] pid_max: default: 32768 minimum: 301 [ 20.684571] Security Framework initialized [ 20.684593] SELinux: Initializing. [ 20.684676] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 20.684690] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 20.685412] Initializing cgroup subsys devices [ 20.685463] Initializing cgroup subsys freezer [ 20.685487] Initializing cgroup subsys net_cls [ 20.685526] Initializing cgroup subsys blkio [ 20.685608] CPU: Testing write buffer coherency: ok [ 20.686025] Setting up static identity map for 0x5273f0 - 0x527448 [ 20.688069] devtmpfs: initialized [ 20.691282] prandom: seed boundary self test passed [ 20.694283] prandom: 100 self tests passed [ 20.694302] pinctrl core: initialized pinctrl subsystem [ 20.694828] regulator-dummy: no parameters [ 20.695232] NET: Registered protocol family 16 [ 20.695612] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 20.696631] cpuidle: using governor ladder [ 20.696653] cpuidle: using governor menu [ 20.696805] Kirkwood: MV88F6282-Rev-A1, TCLK=200000000. [ 20.696824] Feroceon L2: Enabling L2 [ 20.696854] Feroceon L2: Cache support initialised. [ 20.698382] Kirkwood PCIe port 0: link up [ 20.698390] PCI: bus0 uses PCIe port 0 [ 20.698544] PCI host bridge to bus 0000:00 [ 20.698560] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 20.698570] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 20.698578] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 20.699216] PCI: bus0: Fast back to back transfers disabled [ 20.699261] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] [ 20.725754] vgaarb: loaded [ 20.726039] usbcore: registered new interface driver usbfs [ 20.726097] usbcore: registered new interface driver hub [ 20.726197] usbcore: registered new device driver usb [ 20.727014] Switched to clocksource orion_clocksource [ 20.762328] NET: Registered protocol family 2 [ 20.763113] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 20.763168] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 20.763220] TCP: Hash tables configured (established 4096 bind 4096) [ 20.763285] TCP: reno registered [ 20.763296] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 20.763315] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 20.763489] NET: Registered protocol family 1 [ 20.763762] RPC: Registered named UNIX socket transport module. [ 20.763771] RPC: Registered udp transport module. [ 20.763777] RPC: Registered tcp transport module. [ 20.763782] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 20.763833] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 20.764149] Unpacking initramfs... [ 21.149952] Freeing initrd memory: 5884K (c1101000 - c16c0000) [ 21.150106] NetWinder Floating Point Emulator V0.97 (double precision) [ 21.151029] futex hash table entries: 256 (order: -1, 3072 bytes) [ 21.151085] audit: initializing netlink subsys (enabled) [ 21.151136] audit: type=2000 audit(0.550:1): initialized [ 21.151821] zbud: loaded [ 21.152039] VFS: Disk quotas dquot_6.5.2 [ 21.152082] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 21.152527] NFS: Registering the id_resolver key type [ 21.152578] Key type id_resolver registered [ 21.152585] Key type id_legacy registered [ 21.152605] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 21.152617] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 21.152749] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 21.153002] msgmni has been set to 998 [ 21.153146] Key type big_key registered [ 21.155273] alg: No test for stdrng (krng) [ 21.155362] bounce: pool size: 64 pages [ 21.155414] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 21.155429] io scheduler noop registered [ 21.155440] io scheduler deadline registered [ 21.155574] io scheduler cfq registered (default) [ 21.155912] mv_xor mv_xor.0: Marvell shared XOR driver [ 21.187074] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 21.227066] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 21.227197] mv_xor mv_xor.1: Marvell shared XOR driver [ 21.267065] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 21.307066] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 21.307417] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 21.308180] console [ttyS0] disabled [ 21.328228] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A [ 21.941359] console [ttyS0] enabled [ 21.945973] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 21.952380] nand: Eon NAND 128MiB 3,3V 8-bit [ 21.956662] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 21.962357] Scanning device for bad blocks [ 21.971806] Bad eraseblock 100 at 0x000000c80000 [ 21.981713] Bad eraseblock 200 at 0x000001900000 [ 22.029696] 4 cmdlinepart partitions found on MTD device orion_nand [ 22.035988] Creating 4 MTD partitions on "orion_nand": [ 22.041158] 0x000000000000-0x000000100000 : "u-boot" [ 22.046458] 0x000000100000-0x000000500000 : "uImage" [ 22.051753] 0x000000500000-0x000002500000 : "rootfs" [ 22.057066] 0x000002500000-0x000008000000 : "data" [ 22.062801] libphy: Fixed MDIO Bus: probed [ 22.078548] libphy: orion_mdio_bus: probed [ 22.082755] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 22.092295] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:00:02:02 [ 22.101294] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 22.107890] ehci-pci: EHCI PCI platform driver [ 22.112405] ehci-orion: EHCI orion driver [ 22.116496] orion-ehci orion-ehci.0: EHCI Host Controller [ 22.121971] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 22.129703] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 22.147046] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 22.153149] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 22.159989] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 22.167256] usb usb1: Product: EHCI Host Controller [ 22.172153] usb usb1: Manufacturer: Linux 3.16.0-kirkwood-tld-2 ehci_hcd [ 22.178896] usb usb1: SerialNumber: orion-ehci.0 [ 22.184128] hub 1-0:1.0: USB hub found [ 22.187955] hub 1-0:1.0: 1 port detected [ 22.192594] mousedev: PS/2 mouse device common for all mice [ 22.507059] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 22.658463] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 22.665200] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 22.672391] usb 1-1: Product: USB2.0 Hub [ 22.677148] hub 1-1:1.0: USB hub found [ 22.681210] hub 1-1:1.0: 4 ports detected [ 22.967337] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 23.077959] usb 1-1.2: New USB device found, idVendor=18a5, idProduct=0302 [ 23.084875] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 23.092257] usb 1-1.2: Product: STORE N GO [ 23.098141] usb 1-1.2: Manufacturer: Verbatim [ 23.104456] usb 1-1.2: SerialNumber: 1226000000006EFD [ 23.187337] usb 1-1.3: new high-speed USB device number 4 using orion-ehci [ 23.207035] rtc-mv rtc-mv: internal RTC not ticking [ 23.212092] i2c /dev entries driver [ 23.216052] rtc-pcf8563 0-0051: chip found, driver version 0.4.3 [ 23.223487] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 23.231405] hidraw: raw HID events driver (C) Jiri Kosina [ 23.237139] drop_monitor: Initializing network drop monitor service [ 23.243622] TCP: cubic registered [ 23.246969] NET: Registered protocol family 17 [ 23.251559] Key type dns_resolver registered [ 23.256452] registered taskstats version 1 [ 23.262580] rtc-pcf8563 0-0051: setting system clock to 2017-07-12 23:22:13 UTC (1499901733) [ 23.272896] Freeing unused kernel memory: 256K (c0725000 - c0765000) Loading, please wait... [ 23.308722] usb 1-1.3: New USB device found, idVendor=04a9, idProduct=1909 [ 23.315648] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 23.331440] usb 1-1.3: Product: CanoScan [ 23.335404] usb 1-1.3: Manufacturer: Canon [ 23.367812] udevd[55]: starting version 175 [ 23.446628] xhci_hcd 0000:00:01.0: xHCI Host Controller [ 23.504841] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2 [ 23.575280] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 23.596437] SCSI subsystem initialized [ 23.617961] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 23.625239] usb usb2: Product: xHCI Host Controller [ 23.653175] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 23.669612] sata_mv sata_mv.0: cannot get optional clkdev [ 23.675127] sata_mv sata_mv.0: slots 32 ports 2 [ 23.701911] usb usb2: Manufacturer: Linux 3.16.0-kirkwood-tld-2 xhci_hcd [ 23.720873] scsi0 : usb-storage 1-1.2:1.0 [ 23.730414] usbcore: registered new interface driver usb-storage [ 23.746539] usb usb2: SerialNumber: 0000:00:01.0 [ 23.756188] scsi1 : sata_mv [ 23.772956] hub 2-0:1.0: USB hub found [ 23.776804] scsi2 : sata_mv [ 23.780232] usbcore: registered new interface driver uas [ 23.791632] ata1: SATA max UDMA/133 irq 21 [ 23.795748] ata2: SATA max UDMA/133 irq 21 [ 23.805873] hub 2-0:1.0: 2 ports detected [ 23.815037] xhci_hcd 0000:00:01.0: xHCI Host Controller [ 23.821495] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3 [ 23.829334] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 23.836158] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 23.843462] usb usb3: Product: xHCI Host Controller [ 23.848379] usb usb3: Manufacturer: Linux 3.16.0-kirkwood-tld-2 xhci_hcd [ 23.855104] usb usb3: SerialNumber: 0000:00:01.0 [ 23.860734] hub 3-0:1.0: USB hub found [ 23.864536] hub 3-0:1.0: 2 ports detected [ 24.327055] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 24.387079] ata1.00: ATA-8: WDC WD3200BPVT-00ZEST0, 01.01A01, max UDMA/133 [ 24.393983] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 24.457081] ata1.00: configured for UDMA/133 [ 24.477341] scsi 1:0:0:0: Direct-Access ATA WDC WD3200BPVT-0 1A01 PQ: 0 ANSI: 5 [ 24.717916] scsi 0:0:0:0: Direct-Access Verbatim STORE N GO 1.00 PQ: 0 ANSI: 2 [ 24.751085] sd 1:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 24.760140] sd 0:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB) [ 24.768152] sd 1:0:0:0: [sda] 4096-byte physical blocks [ 24.773766] sd 1:0:0:0: [sda] Write Protect is off [ 24.778803] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 24.787978] sd 0:0:0:0: [sdb] Write Protect is off [ 24.794965] sd 0:0:0:0: [sdb] No Caching mode page found [ 24.800367] sd 0:0:0:0: [sdb] Assuming drive cache: write through [ 24.811825] sdb: sdb1 sdb2 [ 24.818115] sd 0:0:0:0: [sdb] Attached SCSI removable disk [ 24.835148] sda: sda1 sda2 sda4 [ 24.840508] sd 1:0:0:0: [sda] Attached SCSI disk [ 24.997056] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 25.017263] ata2.00: ATA-9: WDC WD20EFRX-68EUZN0, 80.00A80, max UDMA/133 [ 25.023995] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 25.047254] ata2.00: configured for UDMA/133 [ 25.067296] scsi 2:0:0:0: Direct-Access ATA WDC WD20EFRX-68E 0A80 PQ: 0 ANSI: 5 [ 25.076630] sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 25.085096] sd 2:0:0:0: [sdc] 4096-byte physical blocks [ 25.090590] sd 2:0:0:0: [sdc] Write Protect is off [ 25.095494] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 25.120934] sdc: sdc1 sdc2 sdc3 sdc4 [ 25.126913] sd 2:0:0:0: [sdc] Attached SCSI disk [ 25.170196] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 25.192044] sd 0:0:0:0: Attached scsi generic sg1 type 0 [ 25.200076] sd 2:0:0:0: Attached scsi generic sg2 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 29.723176] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. [ 32.506498] audit: type=1403 audit(1499901742.730:2): policy loaded auid=4294967295 ses=4294967295 [ 32.524430] systemd[1]: Successfully loaded SELinux policy in 1.510166s. [ 32.532926] random: nonblocking pool is initialized [ 32.935171] NET: Registered protocol family 10 [ 33.017554] ip_tables: (C) 2000-2006 Netfilter Core Team [ 33.657218] systemd[1]: Relabelled /dev and /run in 589.058ms. [ 33.800592] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 33.819166] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)!