=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.03.16 23:19:18 =~=~=~=~=~=~=~=~=~=~=~= printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 CASset=min MALLOC_len=1 ethprime=egiga1 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 eth1addr=00:50:43:00:02:02 eth1mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loidaddr=0x02000000 autoload=no bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console=console=ttyS0,115200 fw_up=disable loadaddr=0x02000000 ethaddr=00:50:43:00:02:02 usb_load_uimage=ext2load usb 0:1 0x200000 /boot/uImage usb_load_uinitrd=ext2load usb 0:1 0x800000 /boot/uInitrd usb_boot=run usb_load_uimage; run usb_load_uinitrd; bootm 0x200000 0x800000 usb_bootcmd=usb start; run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_rootfstype=ext2 usb_rootdelay=10 usb_init=setenv test=1 ubifs_bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 usb_root=LABEL=rootfs usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) serverip=192.168.1.195 ipaddr=192.168.1.188 if_netconsole=ping $serverip ncip=$serverip stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no hddPowerCtrl=no enaAutoRecovery=no ethact=egiga1 Environment size: 2136/131068 bytes Marvell>> run usb_boot ** Bad partition 1 ** ** Bad partition 1 ** ## Booting image at 00200000 ... Bad Magic Number Marvell>> usb reset (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Marvell>> run usb_boot .... . ...... ............ ......................... ................................................... ...................................................................................................... ........................................................................................................ 3166745 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. .............................................................................................................................................................................................................................................................................................. 7179935 bytes read ## Booting image at 00200000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2017-03-16 18:54:40 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3166681 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 00800000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] INITRD: 0x00800040+0x006d8e5f overlaps in-use memory region - disabling initrd [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 120632K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 10440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000010] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008252] Console: colour dummy device 80x30 [ 0.012782] Calibrating delay loop... 990.41 BogoMIPS (lpj=4952064) [ 0.100739] pid_max: default: 32768 minimum: 301 [ 0.105541] Security Framework initialized [ 0.109844] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.116530] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.124689] Initializing cgroup subsys io [ 0.128853] Initializing cgroup subsys devices [ 0.133398] Initializing cgroup subsys freezer [ 0.137977] Initializing cgroup subsys net_cls [ 0.142583] CPU: Testing write buffer coherency: ok [ 0.148112] Setting up static identity map for 0x8200 - 0x8258 [ 0.154347] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.163830] devtmpfs: initialized [ 0.173417] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.183890] prandom: seed boundary self test passed [ 0.193416] prandom: 100 self tests passed [ 0.197609] pinctrl core: initialized pinctrl subsystem [ 0.204571] NET: Registered protocol family 16 [ 0.209625] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.237991] cpuidle: using governor ladder [ 0.267990] cpuidle: using governor menu [ 0.272424] Feroceon L2: Enabling L2 [ 0.276110] Feroceon L2: Cache support initialised. [ 0.281548] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.298634] No ATAGs? [ 0.339754] vgaarb: loaded [ 0.343237] usbcore: registered new interface driver usbfs [ 0.348938] usbcore: registered new interface driver hub [ 0.354398] usbcore: registered new device driver usb [ 0.360815] clocksource: Switched to clocksource orion_clocksource [ 0.434261] NET: Registered protocol family 2 [ 0.439607] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.446794] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.453249] TCP: Hash tables configured (established 1024 bind 1024) [ 0.459732] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.465665] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.472245] NET: Registered protocol family 1 [ 0.477086] RPC: Registered named UNIX socket transport module. [ 0.483124] RPC: Registered udp transport module. [ 0.487893] RPC: Registered tcp transport module. [ 0.492687] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.499615] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.507499] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.513804] audit: initializing netlink subsys (disabled) [ 0.519306] audit: type=2000 audit(0.500:1): initialized [ 0.525180] Initialise system trusted keyring [ 0.530009] zbud: loaded [ 0.533013] VFS: Disk quotas dquot_6.6.0 [ 0.537064] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.544769] NFS: Registering the id_resolver key type [ 0.549941] Key type id_resolver registered [ 0.554248] Key type id_legacy registered [ 0.558351] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.565144] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.571838] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.579551] Key type big_key registered [ 0.597047] Key type asymmetric registered [ 0.601329] Asymmetric key parser 'x509' registered [ 0.606366] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.614038] io scheduler noop registered [ 0.618039] io scheduler deadline registered [ 0.622512] io scheduler cfq registered (default) [ 0.628903] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.637212] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated [ 0.644697] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated [ 0.652660] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.659684] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.666052] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.673010] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.679018] PCI: bus0: Fast back to back transfers disabled [ 0.684711] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.693036] PCI: bus1: Fast back to back transfers enabled [ 0.698678] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.704123] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.751658] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.759296] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.801649] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.809587] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.817691] console [ttyS0] disabled [ 0.821471] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 0.830512] console [ttyS0] enabled [ 0.830512] console [ttyS0] enabled [ 0.837664] bootconsole [earlycon0] disabled [ 0.837664] bootconsole [earlycon0] disabled [ 0.847900] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 0.854328] nand: Samsung NAND 256MiB 3,3V 8-bit [ 0.858971] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.866613] Scanning device for bad blocks [ 0.897254] Bad eraseblock 246 at 0x000001ec0000 [ 0.944196] Bad eraseblock 640 at 0x000005000000 [ 0.955240] Bad eraseblock 700 at 0x000005780000 [ 0.960038] Bad eraseblock 702 at 0x0000057c0000 [ 1.025704] Bad eraseblock 1270 at 0x000009ec0000 [ 1.051239] Bad eraseblock 1464 at 0x00000b700000 [ 1.077406] Bad eraseblock 1664 at 0x00000d000000 [ 1.088533] Bad eraseblock 1724 at 0x00000d780000 [ 1.093441] Bad eraseblock 1726 at 0x00000d7c0000 [ 1.102213] Bad eraseblock 1764 at 0x00000dc80000 [ 1.140388] libphy: Fixed MDIO Bus: probed [ 1.144990] libphy: orion_mdio_bus: probed [ 1.149958] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.229721] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:00:02:02 [ 2.238687] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.245322] ehci-pci: EHCI PCI platform driver [ 2.249880] ehci-orion: EHCI orion driver [ 2.254153] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.259702] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.267716] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 2.290855] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.297164] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.304022] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.311301] usb usb1: Product: EHCI Host Controller [ 2.316205] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.322871] usb usb1: SerialNumber: f1050000.ehci [ 2.328499] hub 1-0:1.0: USB hub found [ 2.332376] hub 1-0:1.0: 1 port detected [ 2.337528] mousedev: PS/2 mouse device common for all mice [ 2.650857] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.803350] usb 1-1: New USB device found, idVendor=125f, idProduct=c83a [ 2.810106] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.817317] usb 1-1: Product: A-DATA USB Flash Drive [ 2.822328] usb 1-1: Manufacturer: A-DATA [ 2.826359] usb 1-1: SerialNumber: 06e7cf43be21fe [ 3.350851] rtc-mv f1010300.rtc: internal RTC not ticking [ 3.356528] i2c /dev entries driver [ 3.361212] rtc-pcf8563 0-0051: chip found, driver version 0.4.4 [ 3.373325] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 3.383293] hidraw: raw HID events driver (C) Jiri Kosina [ 3.389177] drop_monitor: Initializing network drop monitor service [ 3.395821] NET: Registered protocol family 17 [ 3.400604] Key type dns_resolver registered [ 3.405894] registered taskstats version 1 [ 3.410066] Loading compiled-in X.509 certificates [ 3.414993] zswap: loaded using pool lzo/zbud [ 3.420669] Key type encrypted registered [ 3.426653] rtc-pcf8563 0-0051: setting system clock to 2017-03-16 23:20:40 UTC (1489706440) [ 3.437718] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 3.445393] Please append a correct "root=" boot option; here are the available partitions: [ 3.453857] 1f00 262144 mtdblock0 (driver?) [ 3.458944] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 3.467247] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-kirkwood-tld-1 #1 [ 3.474234] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 3.480563] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 3.488356] [] (show_stack) from [] (panic+0x80/0x214) [ 3.495271] [] (panic) from [] (mount_block_root+0x204/0x24c) [ 3.502793] [] (mount_block_root) from [] (mount_root+0xec/0x118) [ 3.510667] [] (mount_root) from [] (prepare_namespace+0x124/0x184) [ 3.518716] [] (prepare_namespace) from [] (kernel_init_freeable+0x208/0x258) [ 3.527641] [] (kernel_init_freeable) from [] (kernel_init+0x8/0xe4) [ 3.535775] [] (kernel_init) from [] (ret_from_fork+0x14/0x24) [ 3.543385] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 82.020846] random: nonblocking pool is initialized