Problem booting GoFlexHome February 23, 2017 01:00PM |
Registered: 11 years ago Posts: 38 |
fw_setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-goflexnet.dtb' fw_setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' fw_setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' fw_setenv usb_boot 'run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi'
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:30:55 -0700) Seagate GoFlex Home SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST31000528AS Firm: CC46 Ser#: 6VPAMCTY Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) 3157805 bytes read in 547 ms (5.5 MiB/s) ** Bad device usb 0 ** ** Bad device usb 0 ** ** Bad device usb 0 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.2.0-kirkwood-tld-1 Created: 2015-11-11 1:34:05 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3157741 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Created: 2012-10-29 22:52:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ...
rescue:~# fw_printenv arcNumber=3338 baudrate=115200 bootcmd=run bootcmd_usb; usb stop; run bootcmd_sata; run bootcmd_pogo; reset bootcmd_pogo=run bootcmd_rescue bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000 bootcmd_sata=run sata_init; run sata_load_uimage; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run usb_load_uimage; run set_bootargs_usb; run usb_boot; bootdelay=3 console=ttyS0,115200 ethact=egiga0 ethaddr=00:10:75:2A:5A:8C led_error=orange blinking led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 rescue_installed=1 sata_device=0:1 sata_init=ide reset sata_load_uimage=mw 0x800000 0 1; ext2load ide $sata_device 0x800000 /boot/uImage sata_root=/dev/sda1 sata_rootdelay=8 sata_rootfstype=ext4 set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts stderr=serial stdin=serial stdout=serial usb_device=0:1 usb_init=usb start; setenv usb_root LABEL=rootfs usb_load_uimage=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext4 led_exit=green off set_bootargs_sata=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts init=/bin/systemd set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts init=/bin/systemd usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi load_uimage=ext2load usb 0:1 0x800000 /boot/uImage load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-goflexhome.dtb sata_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi preboot=run preboot_nc ipaddr=192.168.129.99 serverip=192.168.129.110
fw_setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-goflexnet.dtb' fw_setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' fw_setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' fw_setenv usb_boot 'run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi'
fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi' fw_setenv preboot 'run preboot_nc' fw_setenv ipaddr '192.168.0.xxx' fw_setenv serverip '192.168.0.yyy'
Re: Problem booting GoFlexHome February 23, 2017 03:40PM |
Admin Registered: 13 years ago Posts: 18,575 |
Quote
8. Flashing default u-boot envs image:
......
A special section (B. Flashing default u-boot envs image) about flashing default u-boot envs is included at the end of this installation procedure. Please follow the instruction in this section B to perform this step before continuing with step 9.
Re: Problem booting GoFlexHome March 08, 2017 09:21PM |
Registered: 11 years ago Posts: 38 |