Welcome! Log In Create A New Profile

Advanced

Debian on Iomega EZ Media & Backup Center

Posted by Berryshake 
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 03, 2017 02:01AM
iomega ez Wrote:
-------------------------------------------------------
>
> root@IOMEGA:~# fw_printenv
> Cannot access MTD device /dev/mtd1: No such file o
> r directory
> root@IOMEGA:~#
> 
>
>
> I saved by saveenv and I want to check on boot but
> it gives nothing?

Check at serial console. Interrupt u-boot and
printenv

You might need to post some more info so that I can show you how to set up fw_printenv in Debian. But serial console should list the envs the same way.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
root@IOMEGA-EZ:/mnt/nas# fw_printenv
Warning: Bad CRC, using default environment
bootargs=
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=3
baudrate=115200
stdin=serial,cros-ec-keyb
stdout=serial,lcd
stderr=serial,lcd
root@IOMEGA-EZ:/mnt/nas#

last time I used my old wheezy usb and this time, I used a new jessi usb and it gives me message.

        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix1
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
fw_ver=3.3.2.29823
serial_number=5563Z01001G30100784J0C1
ethaddr=00:D0:B8:14:0B:8A
serialNo=USAD020062
modelname=31997701
serialno=0,01xqV5lWlCJ4voSqhRSkfcpHpi7vDAgRqVwyNe4nzWGO1eGJjRJi8ltftT1y38RqWc,USAD020062,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX1/1.0.4/download_runin.sh
pre_path_conf=IX1/1.0.4/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX1/1.0.4
serverip=192.168.32.4
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext2
bootcmd1=ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; setenv bootargs $(console) $(bootargs_root) $(bootargs_mtd) $(bootargs_end); bootm 0x40000 0x900000;run bootcmd2
bootcmd=ide reset; run bootcmd_usb; usb stop; run bootcmd1
bootcmd_usb=usb reset; run usb_scan; run make_usb_bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd; bootm 0x40000 0x1100000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no

Environment size: 2398/4091 bytes
Marvell>>

I used saveenv but if someone do not have access to serial cable, how can I advise them to use my uImage?
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 03, 2017 03:27PM
iomega ez,

You are not done yet until you can boot with the rootfs label like this:

make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10

And the mtds are not visible in bootlog, so that bootargs_mtd variable seems to have problem. Please get the output of:

cat /proc/mtd
cat /etc/fw_env.config

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
root@IOMEGA-EZ:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00010000 "spi0.0"
root@IOMEGA-EZ:~# cat /etc/fw_env.config
# MTD device name       Device offset   Env. size       Flash sector size       Number of sectors
/dev/mtd0 0xc0000 0x20000 0x20000
root@IOMEGA-EZ:~#

so how should I change uboot ?
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 03, 2017 07:42PM
iomega ez,

> so how should I change uboot ?

Power up, interrupt serial console and,

setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10'

and then
boot

If you can boot all the way into Debian just by doing the above then you can save envs (but don't try anything else). This is to prove that your rootfs was correctly created.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10'
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)

(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................

3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................

7179935 bytes read
## Booting image at 00040000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2017-06-01  10:40:30 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3167923 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes =  6.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Lenovo IX2-ng
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07d7ef4   (8000 kB)
[    0.000000]       .init : 0xc07d8000 - 0xc0822000   ( 296 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b169c   ( 574 kB)
[    0.000000]        .bss : 0xc08b169c - 0xc08ff9d0   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000333] Console: colour dummy device 80x30
[    0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090101] pid_max: default: 32768 minimum: 301
[    0.090208] Security Framework initialized
[    0.090282] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090302] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091088] Initializing cgroup subsys io
[    0.091121] Initializing cgroup subsys devices
[    0.091145] Initializing cgroup subsys freezer
[    0.091178] Initializing cgroup subsys net_cls
[    0.091259] CPU: Testing write buffer coherency: ok
[    0.091703] Setting up static identity map for 0x8200 - 0x8258
[    0.091995] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[    0.095604] devtmpfs: initialized
[    0.101206] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.101670] prandom: seed boundary self test passed
[    0.105425] prandom: 100 self tests passed
[    0.105450] pinctrl core: initialized pinctrl subsystem
[    0.106814] NET: Registered protocol family 16
[    0.107258] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.130100] cpuidle: using governor ladder
[    0.160102] cpuidle: using governor menu
[    0.160539] Feroceon L2: Enabling L2
[    0.160580] Feroceon L2: Cache support initialised.
[    0.160956] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.166580] No ATAGs?
[    0.201541] vgaarb: loaded
[    0.201891] usbcore: registered new interface driver usbfs
[    0.201969] usbcore: registered new interface driver hub
[    0.202031] usbcore: registered new device driver usb
[    0.203134] clocksource: Switched to clocksource orion_clocksource
[    0.258186] NET: Registered protocol family 2
[    0.258976] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259007] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259031] TCP: Hash tables configured (established 1024 bind 1024)
[    0.259093] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.259119] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.259315] NET: Registered protocol family 1
[    0.259709] RPC: Registered named UNIX socket transport module.
[    0.259721] RPC: Registered udp transport module.
[    0.259728] RPC: Registered tcp transport module.
[    0.259735] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.260010] Unpacking initramfs...
[    0.882153] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[    0.882310] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.883462] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.883534] audit: initializing netlink subsys (disabled)
[    0.883587] audit: type=2000 audit(0.880:1): initialized
[    0.883933] Initialise system trusted keyring
[    0.884315] zbud: loaded
[    0.884598] VFS: Disk quotas dquot_6.6.0
[    0.884658] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.885194] NFS: Registering the id_resolver key type
[    0.885231] Key type id_resolver registered
[    0.885240] Key type id_legacy registered
[    0.885266] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.885280] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.885499] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.886001] Key type big_key registered
[    0.905236] Key type asymmetric registered
[    0.905259] Asymmetric key parser 'x509' registered
[    0.905352] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.905372] io scheduler noop registered
[    0.905387] io scheduler deadline registered
[    0.905445] io scheduler cfq registered (default)
[    0.906776] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.907461] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[    0.907885] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[    0.908427] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.943838] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.944088] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.983840] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.984335] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.985646] console [ttyS0] disabled
[    0.985706] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[    1.588125] console [ttyS0] enabled
[    1.593571] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    1.604521] libphy: Fixed MDIO Bus: probed
[    1.608965] libphy: orion_mdio_bus: probed
[    1.617607] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.625750] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[    1.634740] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.641324] ehci-pci: EHCI PCI platform driver
[    1.645906] ehci-orion: EHCI orion driver
[    1.650102] orion-ehci f1050000.ehci: EHCI Host Controller
[    1.655690] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    1.663571] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    1.683168] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    1.689421] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.696271] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.703544] usb usb1: Product: EHCI Host Controller
[    1.708445] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[    1.715105] usb usb1: SerialNumber: f1050000.ehci
[    1.720549] hub 1-0:1.0: USB hub found
[    1.724399] hub 1-0:1.0: 1 port detected
[    1.729307] mousedev: PS/2 mouse device common for all mice
[    1.735601] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    1.742676] i2c /dev entries driver
[    1.748683] hidraw: raw HID events driver (C) Jiri Kosina
[    1.754549] drop_monitor: Initializing network drop monitor service
[    1.761101] NET: Registered protocol family 17
[    1.765857] Key type dns_resolver registered
[    1.770967] registered taskstats version 1
[    1.775158] Loading compiled-in X.509 certificates
[    1.780028] zswap: loaded using pool lzo/zbud
[    1.792489] Key type encrypted registered
[    1.797155] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 00:09:55 UTC (1496534995)
[    1.808269] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[    1.881193] systemd-udevd[81]: starting version 215
[    1.895179] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.043263] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    2.062009] SCSI subsystem initialized
[    2.118926] sata_mv f1080000.sata: slots 32 ports 2
[    2.160542] scsi host0: sata_mv
[    2.179160] scsi host1: sata_mv
[    2.182683] ata1: SATA max UDMA/133 irq 34
[    2.208224] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[    2.215399] ata2: SATA max UDMA/133 irq 34
[    2.219624] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    2.234665] usb 1-1: Product: USB Storage
[    2.238720] usb 1-1: Manufacturer: Generic
[    2.242929] usb 1-1: SerialNumber: 000000009451
[    2.272041] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.279565] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[    2.286543] scsi host2: usb-storage 1-1:1.0
[    2.292425] usbcore: registered new interface driver usb-storage
[    2.301448] usbcore: registered new interface driver uas
[    2.723176] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[    2.763206] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[    2.768718] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    2.833209] ata1.00: configured for UDMA/133
[    2.853599] scsi 0:0:0:0: Direct-Access     ATA      ST340014AS       8.12 PQ: 0 ANSI: 5
[    3.213169] ata2: SATA link down (SStatus 0 SControl F300)
[    3.245408] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    3.255729] sd 0:0:0:0: [sda] Write Protect is off
[    3.260660] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.274811]  sda: sda1
[    3.278890] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.287630] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.294431] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9451 PQ: 0 ANSI: 0
[    3.314749] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.459380] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[    3.469602] sd 2:0:0:0: [sdb] Write Protect is off
[    3.476742] sd 2:0:0:0: [sdb] No Caching mode page found
[    3.482288] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    3.498723]  sdb: sdb1
[    3.512763] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443084/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   15.230963] systemd-udevd[298]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[   15.515130] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   15.738606] orion_wdt: Initial timeout 21 sec
[   15.760777] marvell-cesa: probe of f1030000.crypto failed with error -524
[   15.792668] adt7475 0-002e: ADT7473 device, revision 2
[   15.839513] random: nonblocking pool is initialized
[   15.847751] adt7475 0-002e: Bypassing attenuators on: in1
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443084/994560 blocks
done.
[....] Activating lvm and md swap...[   18.030186] Adding 524284k swap on /swapfile.  Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[   18.824514] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[   19.977981] NET: Registered protocol family 10
[   20.087968] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on   LPF/eth0/00:d0:b8:14:0b:8a
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
[   23.661024] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   23.670946] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 36158 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1258 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1256 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.

Debian GNU/Linux 8 IOMEGA-EZ ttyS0

IOMEGA-EZ login:

yes, it boots fine
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 03, 2017 08:22PM
Cool!

Now you can save it:

Power up, interrupt serial console and,

setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10'
saveenv

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 03, 2017 08:30PM
Regarding your mtdparts that have not been detected by the kernel. This was one of the reasons you could not use fw_printenv.

Try this,

Power up, interrupt serial console and,

setenv bootargs_mtd 'mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)'
boot

Please post the entire serial boot log here.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10'
Marvell>> saveenv
Saving Environment to Flash...
.
Un-Protected 1 sectors
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
.
Protected 1 sectors
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)

(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................

3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................

7179935 bytes read
## Booting image at 00040000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2017-06-01  10:40:30 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3167923 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes =  6.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Lenovo IX2-ng
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07d7ef4   (8000 kB)
[    0.000000]       .init : 0xc07d8000 - 0xc0822000   ( 296 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b169c   ( 574 kB)
[    0.000000]        .bss : 0xc08b169c - 0xc08ff9d0   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000333] Console: colour dummy device 80x30
[    0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090101] pid_max: default: 32768 minimum: 301
[    0.090208] Security Framework initialized
[    0.090281] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090302] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091091] Initializing cgroup subsys io
[    0.091123] Initializing cgroup subsys devices
[    0.091148] Initializing cgroup subsys freezer
[    0.091181] Initializing cgroup subsys net_cls
[    0.091263] CPU: Testing write buffer coherency: ok
[    0.091707] Setting up static identity map for 0x8200 - 0x8258
[    0.091999] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[    0.095609] devtmpfs: initialized
[    0.101208] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.101670] prandom: seed boundary self test passed
[    0.105425] prandom: 100 self tests passed
[    0.105451] pinctrl core: initialized pinctrl subsystem
[    0.106808] NET: Registered protocol family 16
[    0.107252] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.130100] cpuidle: using governor ladder
[    0.160102] cpuidle: using governor menu
[    0.160539] Feroceon L2: Enabling L2
[    0.160580] Feroceon L2: Cache support initialised.
[    0.160955] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.166582] No ATAGs?
[    0.201540] vgaarb: loaded
[    0.201891] usbcore: registered new interface driver usbfs
[    0.201970] usbcore: registered new interface driver hub
[    0.202031] usbcore: registered new device driver usb
[    0.203131] clocksource: Switched to clocksource orion_clocksource
[    0.258199] NET: Registered protocol family 2
[    0.258984] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259016] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259039] TCP: Hash tables configured (established 1024 bind 1024)
[    0.259101] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.259128] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.259324] NET: Registered protocol family 1
[    0.259721] RPC: Registered named UNIX socket transport module.
[    0.259733] RPC: Registered udp transport module.
[    0.259740] RPC: Registered tcp transport module.
[    0.259747] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.260021] Unpacking initramfs...
[    0.882069] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[    0.882226] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.883379] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.883453] audit: initializing netlink subsys (disabled)
[    0.883507] audit: type=2000 audit(0.880:1): initialized
[    0.883856] Initialise system trusted keyring
[    0.884242] zbud: loaded
[    0.884524] VFS: Disk quotas dquot_6.6.0
[    0.884583] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.885118] NFS: Registering the id_resolver key type
[    0.885155] Key type id_resolver registered
[    0.885165] Key type id_legacy registered
[    0.885190] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.885204] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.885424] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.885927] Key type big_key registered
[    0.905175] Key type asymmetric registered
[    0.905197] Asymmetric key parser 'x509' registered
[    0.905290] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.905310] io scheduler noop registered
[    0.905326] io scheduler deadline registered
[    0.905384] io scheduler cfq registered (default)
[    0.906714] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.907396] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[    0.907820] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[    0.908364] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.943838] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.944087] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.983835] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.984332] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.985644] console [ttyS0] disabled
[    0.985708] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[    1.588126] console [ttyS0] enabled
[    1.593564] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    1.604507] libphy: Fixed MDIO Bus: probed
[    1.608949] libphy: orion_mdio_bus: probed
[    1.617611] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.625748] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[    1.634743] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.641325] ehci-pci: EHCI PCI platform driver
[    1.645907] ehci-orion: EHCI orion driver
[    1.650106] orion-ehci f1050000.ehci: EHCI Host Controller
[    1.655693] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    1.663578] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    1.683166] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    1.689423] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.696272] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.703545] usb usb1: Product: EHCI Host Controller
[    1.708446] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[    1.715106] usb usb1: SerialNumber: f1050000.ehci
[    1.720557] hub 1-0:1.0: USB hub found
[    1.724400] hub 1-0:1.0: 1 port detected
[    1.729307] mousedev: PS/2 mouse device common for all mice
[    1.735605] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    1.742678] i2c /dev entries driver
[    1.748682] hidraw: raw HID events driver (C) Jiri Kosina
[    1.754552] drop_monitor: Initializing network drop monitor service
[    1.761100] NET: Registered protocol family 17
[    1.765857] Key type dns_resolver registered
[    1.770966] registered taskstats version 1
[    1.775159] Loading compiled-in X.509 certificates
[    1.780029] zswap: loaded using pool lzo/zbud
[    1.792490] Key type encrypted registered
[    1.797152] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 00:28:48 UTC (1496536128)
[    1.808258] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[    1.881346] systemd-udevd[81]: starting version 215
[    1.895249] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.043272] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    2.065944] SCSI subsystem initialized
[    2.122023] sata_mv f1080000.sata: slots 32 ports 2
[    2.162732] scsi host0: sata_mv
[    2.181162] scsi host1: sata_mv
[    2.190420] ata1: SATA max UDMA/133 irq 34
[    2.207183] ata2: SATA max UDMA/133 irq 34
[    2.212228] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[    2.223237] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    2.230424] usb 1-1: Product: USB Storage
[    2.246635] usb 1-1: Manufacturer: Generic
[    2.250849] usb 1-1: SerialNumber: 000000009451
[    2.271232] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.278712] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[    2.285688] scsi host2: usb-storage 1-1:1.0
[    2.291577] usbcore: registered new interface driver usb-storage
[    2.300588] usbcore: registered new interface driver uas
[    2.753174] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[    2.793202] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[    2.798716] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    2.843381] ata1.00: configured for UDMA/133
[    2.863598] scsi 0:0:0:0: Direct-Access     ATA      ST340014AS       8.12 PQ: 0 ANSI: 5
[    3.223166] ata2: SATA link down (SStatus 0 SControl F300)
[    3.255548] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    3.265852] sd 0:0:0:0: [sda] Write Protect is off
[    3.270785] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.285040] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9451 PQ: 0 ANSI: 0
[    3.293411]  sda: sda1
[    3.297691] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.310165] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.316062] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.444630] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[    3.453242] sd 2:0:0:0: [sdb] Write Protect is off
[    3.459108] sd 2:0:0:0: [sdb] No Caching mode page found
[    3.464476] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    3.478719]  sdb: sdb1
[    3.491885] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443092/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   15.354038] systemd-udevd[299]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[   15.624772] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   15.826583] adt7475 0-002e: ADT7473 device, revision 2
[   15.852394] adt7475 0-002e: Bypassing attenuators on: in1
[   15.883722] orion_wdt: Initial timeout 21 sec
[   15.921651] marvell-cesa: probe of f1030000.crypto failed with error -524
[   15.970611] random: nonblocking pool is initialized
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443092/994560 blocks
done.
[....] Activating lvm and md swap...[   18.058559] Adding 524284k swap on /swapfile.  Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[   18.834519] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[   19.980294] NET: Registered protocol family 10
[   20.087356] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on   LPF/eth0/00:d0:b8:14:0b:8a
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
[   23.683654] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   23.693575] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 32952 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1259 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1257 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.

Debian GNU/Linux 8 IOMEGA-EZ ttyS0

IOMEGA-EZ login:

done

root@IOMEGA-EZ:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00010000 "spi0.0"
root@IOMEGA-EZ:~# cat /etc/fw_env.config
# MTD device name       Device offset   Env. size       Flash sector size      Number of sectors
/dev/mtd0 0xc0000 0x20000 0x20000
root@IOMEGA-EZ:~# fw_printenv
Warning: Bad CRC, using default environment
bootargs=
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=3
baudrate=115200
stdin=serial,cros-ec-keyb
stdout=serial,lcd
stderr=serial,lcd
root@IOMEGA-EZ:~#

still have the same output?

        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix1
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
fw_ver=3.3.2.29823
serial_number=5563Z01001G30100784J0C1
ethaddr=00:D0:B8:14:0B:8A
serialNo=USAD020062
modelname=31997701
serialno=0,01xqV5lWlCJ4voSqhRSkfcpHpi7vDAgRqVwyNe4nzWGO1eGJjRJi8ltftT1y38RqWc,USAD020062,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX1/1.0.4/download_runin.sh
pre_path_conf=IX1/1.0.4/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX1/1.0.4
serverip=192.168.32.4
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
bootcmd1=ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; setenv bootargs $(console) $(bootargs_root) $(bootargs_mtd) $(bootargs_end); bootm 0x40000 0x900000;run bootcmd2
bootcmd=ide reset; run bootcmd_usb; usb stop; run bootcmd1
bootcmd_usb=usb reset; run usb_scan; run make_usb_bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd; bootm 0x40000 0x1100000
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no

Environment size: 2378/4091 bytes
Marvell>>

here is printenv output
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 03, 2017 09:13PM
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix1
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
fw_ver=3.3.2.29823
serial_number=5563Z01001G30100784J0C1
ethaddr=00:D0:B8:14:0B:8A
serialNo=USAD020062
modelname=31997701
serialno=0,01xqV5lWlCJ4voSqhRSkfcpHpi7vDAgRqVwyNe4nzWGO1eGJjRJi8ltftT1y38RqWc,USAD020062,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX1/1.0.4/download_runin.sh
pre_path_conf=IX1/1.0.4/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX1/1.0.4
serverip=192.168.32.4
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
bootcmd1=ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; setenv bootargs $(console) $(bootargs_root) $(bootargs_mtd) $(bootargs_end); bootm 0x40000 0x900000;run bootcmd2
bootcmd=ide reset; run bootcmd_usb; usb stop; run bootcmd1
bootcmd_usb=usb reset; run usb_scan; run make_usb_bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd; bootm 0x40000 0x1100000
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no

Environment size: 2378/4091 bytes
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)

(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................

3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................

7179935 bytes read
## Booting image at 00040000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2017-06-01  10:40:30 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3167923 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes =  6.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Lenovo IX2-ng
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07d7ef4   (8000 kB)
[    0.000000]       .init : 0xc07d8000 - 0xc0822000   ( 296 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b169c   ( 574 kB)
[    0.000000]        .bss : 0xc08b169c - 0xc08ff9d0   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000333] Console: colour dummy device 80x30
[    0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090101] pid_max: default: 32768 minimum: 301
[    0.090208] Security Framework initialized
[    0.090281] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090302] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091088] Initializing cgroup subsys io
[    0.091121] Initializing cgroup subsys devices
[    0.091145] Initializing cgroup subsys freezer
[    0.091178] Initializing cgroup subsys net_cls
[    0.091259] CPU: Testing write buffer coherency: ok
[    0.091703] Setting up static identity map for 0x8200 - 0x8258
[    0.091995] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[    0.095604] devtmpfs: initialized
[    0.101206] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.101670] prandom: seed boundary self test passed
[    0.105425] prandom: 100 self tests passed
[    0.105450] pinctrl core: initialized pinctrl subsystem
[    0.106814] NET: Registered protocol family 16
[    0.107257] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.130099] cpuidle: using governor ladder
[    0.160101] cpuidle: using governor menu
[    0.160544] Feroceon L2: Enabling L2
[    0.160584] Feroceon L2: Cache support initialised.
[    0.160959] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.166585] No ATAGs?
[    0.201539] vgaarb: loaded
[    0.201890] usbcore: registered new interface driver usbfs
[    0.201969] usbcore: registered new interface driver hub
[    0.202030] usbcore: registered new device driver usb
[    0.203137] clocksource: Switched to clocksource orion_clocksource
[    0.258198] NET: Registered protocol family 2
[    0.258988] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259019] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259042] TCP: Hash tables configured (established 1024 bind 1024)
[    0.259104] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.259130] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.259323] NET: Registered protocol family 1
[    0.259720] RPC: Registered named UNIX socket transport module.
[    0.259731] RPC: Registered udp transport module.
[    0.259739] RPC: Registered tcp transport module.
[    0.259746] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.260018] Unpacking initramfs...
[    0.882184] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[    0.882340] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.883500] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.883573] audit: initializing netlink subsys (disabled)
[    0.883624] audit: type=2000 audit(0.880:1): initialized
[    0.883973] Initialise system trusted keyring
[    0.884359] zbud: loaded
[    0.884643] VFS: Disk quotas dquot_6.6.0
[    0.884703] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.885238] NFS: Registering the id_resolver key type
[    0.885280] Key type id_resolver registered
[    0.885290] Key type id_legacy registered
[    0.885315] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.885329] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.885547] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.886050] Key type big_key registered
[    0.905304] Key type asymmetric registered
[    0.905326] Asymmetric key parser 'x509' registered
[    0.905419] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.905438] io scheduler noop registered
[    0.905454] io scheduler deadline registered
[    0.905511] io scheduler cfq registered (default)
[    0.906842] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.907524] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[    0.907947] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[    0.908490] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.943841] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.944088] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.983838] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.984334] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.985644] console [ttyS0] disabled
[    0.985707] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[    1.588123] console [ttyS0] enabled
[    1.593563] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    1.604494] libphy: Fixed MDIO Bus: probed
[    1.608941] libphy: orion_mdio_bus: probed
[    1.617635] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.625763] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[    1.634758] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.641340] ehci-pci: EHCI PCI platform driver
[    1.645921] ehci-orion: EHCI orion driver
[    1.650119] orion-ehci f1050000.ehci: EHCI Host Controller
[    1.655710] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    1.663578] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    1.683170] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    1.689429] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.696280] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.703552] usb usb1: Product: EHCI Host Controller
[    1.708453] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[    1.715113] usb usb1: SerialNumber: f1050000.ehci
[    1.720559] hub 1-0:1.0: USB hub found
[    1.724408] hub 1-0:1.0: 1 port detected
[    1.729314] mousedev: PS/2 mouse device common for all mice
[    1.735609] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    1.742685] i2c /dev entries driver
[    1.748679] hidraw: raw HID events driver (C) Jiri Kosina
[    1.754549] drop_monitor: Initializing network drop monitor service
[    1.761098] NET: Registered protocol family 17
[    1.765856] Key type dns_resolver registered
[    1.770961] registered taskstats version 1
[    1.775157] Loading compiled-in X.509 certificates
[    1.780027] zswap: loaded using pool lzo/zbud
[    1.792479] Key type encrypted registered
[    1.797140] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 00:33:34 UTC (1496536414)
[    1.808251] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[    1.880881] systemd-udevd[81]: starting version 215
[    1.895215] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.043274] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    2.067148] SCSI subsystem initialized
[    2.117277] sata_mv f1080000.sata: slots 32 ports 2
[    2.160500] scsi host0: sata_mv
[    2.180713] scsi host1: sata_mv
[    2.187683] ata1: SATA max UDMA/133 irq 34
[    2.191828] ata2: SATA max UDMA/133 irq 34
[    2.208232] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[    2.220043] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    2.234983] usb 1-1: Product: USB Storage
[    2.239043] usb 1-1: Manufacturer: Generic
[    2.251231] usb 1-1: SerialNumber: 000000009451
[    2.272085] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.279608] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[    2.286586] scsi host2: usb-storage 1-1:1.0
[    2.292478] usbcore: registered new interface driver usb-storage
[    2.301505] usbcore: registered new interface driver uas
[    2.753178] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[    2.793206] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[    2.798724] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    2.863210] ata1.00: configured for UDMA/133
[    2.883595] scsi 0:0:0:0: Direct-Access     ATA      ST340014AS       8.12 PQ: 0 ANSI: 5
[    3.243171] ata2: SATA link down (SStatus 0 SControl F300)
[    3.275680] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    3.286570] sd 0:0:0:0: [sda] Write Protect is off
[    3.291676] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9451 PQ: 0 ANSI: 0
[    3.300001] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.319083] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.324700]  sda: sda1
[    3.328961] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.334026] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.456754] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[    3.465362] sd 2:0:0:0: [sdb] Write Protect is off
[    3.471236] sd 2:0:0:0: [sdb] No Caching mode page found
[    3.476600] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    3.490844]  sdb: sdb1
[    3.504014] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443094/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   15.334064] systemd-udevd[299]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[   15.585510] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   15.802619] adt7475 0-002e: ADT7473 device, revision 2
[   15.850649] adt7475 0-002e: Bypassing attenuators on: in1
[   15.864544] orion_wdt: Initial timeout 21 sec
[   15.896435] marvell-cesa: probe of f1030000.crypto failed with error -524
[   15.950080] random: nonblocking pool is initialized
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443094/994560 blocks
done.
[....] Activating lvm and md swap...[   18.280053] Adding 524284k swap on /swapfile.  Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[   19.094475] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[   20.247675] NET: Registered protocol family 10
[   20.357368] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on   LPF/eth0/00:d0:b8:14:0b:8a
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
[   23.868760] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   23.878692] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 38961 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1259 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1257 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.

Debian GNU/Linux 8 IOMEGA-EZ ttyS0

IOMEGA-EZ login:

here it is
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootargs_mtd 'mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)'
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)

(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................

3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................

7179935 bytes read
## Booting image at 00040000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2017-06-01  10:40:30 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3167923 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes =  6.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Lenovo IX2-ng
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07d7ef4   (8000 kB)
[    0.000000]       .init : 0xc07d8000 - 0xc0822000   ( 296 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b169c   ( 574 kB)
[    0.000000]        .bss : 0xc08b169c - 0xc08ff9d0   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000333] Console: colour dummy device 80x30
[    0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090101] pid_max: default: 32768 minimum: 301
[    0.090204] Security Framework initialized
[    0.090276] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090296] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091078] Initializing cgroup subsys io
[    0.091111] Initializing cgroup subsys devices
[    0.091135] Initializing cgroup subsys freezer
[    0.091167] Initializing cgroup subsys net_cls
[    0.091249] CPU: Testing write buffer coherency: ok
[    0.091693] Setting up static identity map for 0x8200 - 0x8258
[    0.091986] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[    0.095595] devtmpfs: initialized
[    0.101183] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.101644] prandom: seed boundary self test passed
[    0.105399] prandom: 100 self tests passed
[    0.105425] pinctrl core: initialized pinctrl subsystem
[    0.106792] NET: Registered protocol family 16
[    0.107236] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.130101] cpuidle: using governor ladder
[    0.160099] cpuidle: using governor menu
[    0.160542] Feroceon L2: Enabling L2
[    0.160583] Feroceon L2: Cache support initialised.
[    0.160958] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.166581] No ATAGs?
[    0.201535] vgaarb: loaded
[    0.201888] usbcore: registered new interface driver usbfs
[    0.201966] usbcore: registered new interface driver hub
[    0.202026] usbcore: registered new device driver usb
[    0.203131] clocksource: Switched to clocksource orion_clocksource
[    0.258203] NET: Registered protocol family 2
[    0.258995] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259027] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.259050] TCP: Hash tables configured (established 1024 bind 1024)
[    0.259112] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.259138] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.259331] NET: Registered protocol family 1
[    0.259729] RPC: Registered named UNIX socket transport module.
[    0.259741] RPC: Registered udp transport module.
[    0.259748] RPC: Registered tcp transport module.
[    0.259756] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.260030] Unpacking initramfs...
[    0.882257] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[    0.882412] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.883564] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.883638] audit: initializing netlink subsys (disabled)
[    0.883691] audit: type=2000 audit(0.880:1): initialized
[    0.884038] Initialise system trusted keyring
[    0.884425] zbud: loaded
[    0.884713] VFS: Disk quotas dquot_6.6.0
[    0.884774] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.885302] NFS: Registering the id_resolver key type
[    0.885340] Key type id_resolver registered
[    0.885349] Key type id_legacy registered
[    0.885374] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.885388] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.885607] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.886109] Key type big_key registered
[    0.905354] Key type asymmetric registered
[    0.905376] Asymmetric key parser 'x509' registered
[    0.905468] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.905489] io scheduler noop registered
[    0.905504] io scheduler deadline registered
[    0.905562] io scheduler cfq registered (default)
[    0.906895] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.907577] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[    0.908000] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[    0.908543] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.943839] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.944086] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.983835] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.984334] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.985645] console [ttyS0] disabled
[    0.985708] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[    1.587860] console [ttyS0] enabled
[    1.593304] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    1.598138] 3 cmdlinepart partitions found on MTD device spi0.0
[    1.604118] Creating 3 MTD partitions on "spi0.0":
[    1.608932] 0x000000000000-0x00000007e000 : "u-boot"
[    1.613933] mtd: partition "u-boot" doesn't end on an erase block -- force read-only
[    1.622936] 0x00000007f000-0x000000080000 : "env"
[    1.627717] mtd: partition "env" doesn't start on an erase block boundary -- force read-only
[    1.637403] 0x00000007e000-0x00000007f000 : "env2"
[    1.642221] mtd: partition "env2" doesn't start on an erase block boundary -- force read-only
[    1.652959] libphy: Fixed MDIO Bus: probed
[    1.657462] libphy: orion_mdio_bus: probed
[    1.666228] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.674322] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[    1.683275] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.689857] ehci-pci: EHCI PCI platform driver
[    1.694485] ehci-orion: EHCI orion driver
[    1.698686] orion-ehci f1050000.ehci: EHCI Host Controller
[    1.704280] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    1.712207] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    1.733152] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    1.739396] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.746243] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.753516] usb usb1: Product: EHCI Host Controller
[    1.758416] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[    1.765077] usb usb1: SerialNumber: f1050000.ehci
[    1.770565] hub 1-0:1.0: USB hub found
[    1.774414] hub 1-0:1.0: 1 port detected
[    1.779306] mousedev: PS/2 mouse device common for all mice
[    1.785573] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    1.792641] i2c /dev entries driver
[    1.798530] hidraw: raw HID events driver (C) Jiri Kosina
[    1.804405] drop_monitor: Initializing network drop monitor service
[    1.810943] NET: Registered protocol family 17
[    1.815705] Key type dns_resolver registered
[    1.820827] registered taskstats version 1
[    1.825025] Loading compiled-in X.509 certificates
[    1.829901] zswap: loaded using pool lzo/zbud
[    1.842384] Key type encrypted registered
[    1.847042] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 09:44:00 UTC (1496569440)
[    1.858146] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[    1.931099] systemd-udevd[82]: starting version 215
[    1.945207] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.093232] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    2.111933] SCSI subsystem initialized
[    2.177545] sata_mv f1080000.sata: slots 32 ports 2
[    2.218511] scsi host0: sata_mv
[    2.233319] scsi host1: sata_mv
[    2.246859] ata1: SATA max UDMA/133 irq 34
[    2.250985] ata2: SATA max UDMA/133 irq 34
[    2.268234] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[    2.280435] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    2.294277] usb 1-1: Product: USB Storage
[    2.298316] usb 1-1: Manufacturer: Generic
[    2.302542] usb 1-1: SerialNumber: 000000009451
[    2.332262] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.339740] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[    2.346800] scsi host2: usb-storage 1-1:1.0
[    2.352703] usbcore: registered new interface driver usb-storage
[    2.361693] usbcore: registered new interface driver uas
[    2.813173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[    2.853200] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[    2.858716] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    2.923204] ata1.00: configured for UDMA/133
[    2.943607] scsi 0:0:0:0: Direct-Access     ATA      ST340014AS       8.12 PQ: 0 ANSI: 5
[    3.303170] ata2: SATA link down (SStatus 0 SControl F300)
[    3.335605] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    3.346466] sd 0:0:0:0: [sda] Write Protect is off
[    3.351535] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9451 PQ: 0 ANSI: 0
[    3.359913] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.379144] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.384733]  sda: sda1
[    3.389022] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.394089] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.515883] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[    3.524490] sd 2:0:0:0: [sdb] Write Protect is off
[    3.530363] sd 2:0:0:0: [sdb] No Caching mode page found
[    3.535734] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    3.549903]  sdb: sdb1
[    3.563202] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443103/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   15.384007] systemd-udevd[300]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[   15.664791] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   15.823843] adt7475 0-002e: ADT7473 device, revision 2
[   15.862602] adt7475 0-002e: Bypassing attenuators on: in1
[   15.908578] orion_wdt: Initial timeout 21 sec
[   15.948062] marvell-cesa: probe of f1030000.crypto failed with error -524
[   16.037240] random: nonblocking pool is initialized
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443103/994560 blocks
done.
[....] Activating lvm and md swap...[   18.300066] Adding 524284k swap on /swapfile.  Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[   19.104501] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[   20.248944] NET: Registered protocol family 10
[   20.357204] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on   LPF/eth0/00:d0:b8:14:0b:8a
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
[   24.022996] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   24.032919] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 39399 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1262 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1260 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.

Debian GNU/Linux 8 IOMEGA-EZ ttyS0

IOMEGA-EZ login:

please ignore post above, here it is
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 04, 2017 02:22PM
So now SPI is working and MTD is working. But the definition seems wrong.

[    1.593304] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    1.598138] 3 cmdlinepart partitions found on MTD device spi0.0
[    1.604118] Creating 3 MTD partitions on "spi0.0":
[    1.608932] 0x000000000000-0x00000007e000 : "u-boot"
[    1.613933] mtd: partition "u-boot" doesn't end on an erase block -- force read-only
[    1.622936] 0x00000007f000-0x000000080000 : "env"
[    1.627717] mtd: partition "env" doesn't start on an erase block boundary -- force read-only
[    1.637403] 0x00000007e000-0x00000007f000 : "env2"
[    1.642221] mtd: partition "env2" doesn't start on an erase block boundary -- force read-only

You need to:

1. Look for the correct MTD definition (search here and NAS Central).
2. Look for the correct /etc/fw_env.config for this box.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
should I boot with old kernel on debian 6?
First, you are probably better off with a DTB that supports this device. There is no absolute guarantee that the DTB for the IX2-ng has all the bits and pieces in the correct place. That said, most of these devices are pretty close to being the same.

The MTD has sector misaligned problems even on the IX2-ng. This is because Linux does not know about the actual SPI flash chip in the device. Linux has picked the flash geometry for the closest SPI flash device that it knows about. The actual flash chip in the device can erase to page boundaries that the stock Linux driver just cannot use. Uboot knows about the page boundaries and sets up the Uboot environment to those boundaries but Linux chokes.

You would need to edit the Linux m25p80 flash driver to correct the problem.
I need to point out that the MTD sector misaligned problem is documented in the kirkwood-lenovo-ix2-ng.dts file. If your device has the same SPI flash chip, you will have the same problem. If your device has a different SPI flash chip, you need a DTB/DTS file that supports the hardware in your device.
as far as I know, they use the same board. but EZ boark have only 1 sata port and 128MB memory on board.

same board but less parts.
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 13, 2017 09:38PM
iomega ez Wrote:
-------------------------------------------------------
> as far as I know, they use the same board. but EZ
> boark have only 1 sata port and 128MB memory on bo
> ard.
>
> same board but less parts.

Since you have serial console, and can set the envs there, no need to worry about the MTD. As long as other aspects of this box are working then it is fine. You can remove the mtdparts from bootargs.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
from wiki page

wiki
tun: Universal TUN/TAP device driver, 1.6 
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> 
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA 
sd 1:0:0:0: [sda] Sector size 0 reported, assuming 512. 
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB) 
3 cmdlinepart partitions found on MTD device spi_flash 
Creating 3 MTD partitions on "spi_flash": 
0x000000000000-0x00000007e000 : "u-boot" 
0x00000007f000-0x000000080000 : "env" 
0x00000007e000-0x00000007f000 : "env2" 
sda:Using Hamming 1-bit ECC for NAND device 
No NAND device found!!!

but on dts file(kirkwood-lenovo-ix2-ng.dts)
#include "kirkwood-lenovo-ix2-common.dtsi"

/ {
	model = "Lenovo IX2-ng";
	compatible = "lenovo,ix2", "marvell,kirkwood-88f6282", "marvell,kirkwood";

	ocp@f1000000 {
		spi@10600 {
			status = "okay";

			flash@0 {
				#address-cells = <1>;
				#size-cells = <1>;
				/* MX25L8006E can do 4K sector handling but
				 * sadly not in spi-nor.c yet.
				 */
//				compatible = "mxicy,mx25l8006e", "jedec,spi-nor";
				compatible = "mxicy,mx25l8005", "jedec,spi-nor";
				spi-max-frequency = <50000000>;
				reg = <0>; /* Chip-select 0 */
				mode = <0>;

				partition@0 {
					reg = <0x0 0x7e000>;
					label = "u-boot";
				};

				partition@1 {
					reg = <0x7e000 0x1000>;
					label = "u-boot env2";
				};

				partition@2 {
					reg = <0x7f000 0x1000>;
					label = "u-boot env";
				};
			};
		};
	};
};

is this why I have wrong MTD?
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 23, 2017 12:18AM
iomega_ez,

> is this why I have wrong MTD?

Not really. What you have

mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)

is the same as in the DTS.

> partition@0 {
> reg = <0x0 0x7e000>;
> label = "u-boot";
> };
> 
> partition@1 {
> reg = <0x7e000 0x1000>;
> label = "u-boot env2";
> };
> 
> partition@2 {
> reg = <0x7f000 0x1000>;
> label = "u-boot env";

Regardless, the mtdparts in bootargs takes precedent. So it is fine.

The error Indicated that the flash sector boundary is not 0x1000 (4K).

[    1.593304] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    1.598138] 3 cmdlinepart partitions found on MTD device spi0.0
[    1.604118] Creating 3 MTD partitions on "spi0.0":
[    1.608932] 0x000000000000-0x00000007e000 : "u-boot"
[    1.613933] mtd: partition "u-boot" doesn't end on an erase block -- force read-only
[    1.622936] 0x00000007f000-0x000000080000 : "env"
[    1.627717] mtd: partition "env" doesn't start on an erase block boundary -- force read-only
[    1.637403] 0x00000007e000-0x00000007f000 : "env2"
[    1.642221] mtd: partition "env2" doesn't start on an erase block boundary -- force read-only

So the only explanation for this error is the flash sectore boundary is 0x10000 (64K). But your stock boot log says it is 4K.

SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)

So the DTS needs to be defined differently for this box to match the one that u-boot already knows about (4K).
.

Please post what you know about the SPI flash type (probably from GPL or webistes such as NASCentral), and also post the DTS that you are using.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner



Edited 4 time(s). Last edit at 06/23/2017 02:10AM by bodhi.
Just changing the DTS won't help the fact that Linux does not know about that flash chip. It would require patching the SPI flash driver to recognize the chip correctly.

You can, however, get the U-Boot environment to appear correctly in Linux. It will be in read-only mode because Linux can't erase/program to the 4K sector boundaries of the U-Boot environment.

In Debian, you need to install "u-boot-tools" package. Then put this in a configuration file named "/etc/fw_env.config". You will have to be "root" to do these things.

# device Offset Size Sector size
/dev/mtd2 0x7e000 0x1000 0x1000
/dev/mtd1 0x7f000 0x1000 0x1000

This will describe where the U-Boot environment(s) are to the U-Boot tools. Now you should be able to use the "fw_printenv" command. You will have to be "root" or you will have to change the permissions on the "/dev/mtd" devices to use the fw_printenv command.
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
June 27, 2017 02:07PM
sarcastic.mannequin,

> Just changing the DTS won't help the fact that Lin
> ux does not know about that flash chip. It would r
> equire patching the SPI flash driver to recognize
> the chip correctly.

True, there are 2 parts: DTS and dirver. If the flash type appear on the list, then it's easier. If it is not, then some change in the driver is needed, and it might be quite simple, might be not.

> In Debian, you need to install "u-boot-tools" pack
> age. Then put this in a configuration file named "
> /etc/fw_env.config". You will have to be "root" to
> do these things.
>
> # device Offset Size Sector size
> /dev/mtd2 0x7e000 0x1000 0x1000
> /dev/mtd1 0x7f000 0x1000 0x1000
>
> This will describe where the U-Boot environment(s)
> are to the U-Boot tools. Now you should be able to
> use the "fw_printenv" command. You will have to be
> "root" or you will have to change the permissions
> on the "/dev/mtd" devices to use the fw_printenv
> command.

All these are in the rootfs Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
I installed omv3.0 on iomega ez.

it works fine except network speed is reduced to
samba 20MB/s
ftp 30MB/s

normally I get 50MB/s.

but I don't know why???
old kernel on debin wheezy

is it something wrong with new kernel? or jus omv?
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device?
July 01, 2017 03:59AM
Take a look at the benchmarks to see how other people are testing it:
http://forum.doozan.com/read.php?2,23630


Quote

Benchmarks

Pogo ProV3 vs Pogo E02
Another Pogo Pro V3 benchmarks
Network performance - SAMBA - NFS (various protocols)
Pogo Pro V3 Network NFS benchmarks
Kirkwood vs OXNAS network performance (with flow control)
Kirkwood vs OXNAS network performance (flow control turned off )
OXNAS vs OXNAS network performance (flow control turned off)

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: