NSA325V2 - Installation of Debian-4.4.0-kirkwood-tld-1-rootfs fails November 27, 2016 01:55AM |
Registered: 7 years ago Posts: 9 |
1. Format a new USB drive with a single Ext3 partition, and label it rootfs. In addition, I've set the bootflag for this partition. cd /media/sdb1 tar -xjf Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 Adjust fstab. ext2 -> ext3 Generate the uImage with DTB embedded inside: cd /media/sdb1/boot cp -a zImage-4.4.0-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-goflexnet.dtb >> zImage.fdt mv uImage uImage.orig mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.4.0-kirkwood-tld-1 -d zImage.fdt uImage sync Done. Take this USB rootfs to your plug and cold start.My NAS isn't booting. The bootlog is:
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 800Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8 DRAM CS[0] base 0x00000000 size 512MB DRAM Total size 512MB 16bit width Addresses 10M - 0M are saved for the U-Boot usage. Mem malloc Initialization (10M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Kernel address is 0xc80000. Streaming disabled Write allocate disabled USB 0: host mode [BlueDBG] reseting SoC Pex[0] 0 ... PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 [BlueDBG] reseting SoC Pex[1] 0 ... [BlueDBG] reseting SoC Pex[1] 1 ... [BlueDBG] reseting SoC Pex[1] 2 ... [BlueDBG] reseting SoC Pex[1] 3 ... [BlueDBG] reseting SoC Pex[1] 4 ... [BlueDBG] reseting SoC Pex[1] 5 ... [BlueDBG] reseting SoC Pex[1] 6 ... [BlueDBG] reseting SoC Pex[1] 7 ... [BlueDBG] reseting SoC Pex[1] 8 ... [BlueDBG] reseting SoC Pex[1] 9 ... [BlueDBG] reseting SoC Pex[1] 10 ... PEX 1: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found ** Unable to read "/uImage" from usb 0:1 ** ** Unable to read "/uInitrd" from usb 0:1 ** ## Booting image at 02000000 ... Bad Magic Number Marvell>>The USB card is located in the left rear USB slot, when seen from behind. I've adjusted the boot envs as bescribed here, but no luck
Marvell>> printenv bootdelay=2 baudrate=115200 loads_echo=0 ipaddr=10.4.52.165 serverip=10.4.52.7 rootpath=/srv/ubuntu netmask=255.255.255.0 nandEcc=1bit MODEL_ID=AE03 PRODUCT_NAME=NSA-325v2 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=MitraStar Technology Corp. run_diag=yes console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 ethaddr=00:50:43:00:02:02 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 arcNumber=4495 bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000 bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr) to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)=root=LABEL=rootfs loglevel=8 bootargs_linux=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 bootcmd='run bootcmd_linux' stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no enaAutoRecovery=yes kernel_addr=0xc80000 pcieTune=no pcieTune1=no bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8I've searched a lot in this forum and google, desperately tried some suggestions, but as stated at the begin of this thread, no luck for me.
Re: NSA325V2 - Installation of Debian-4.4.0-kirkwood-tld-1-rootfs fails November 27, 2016 02:48AM |
Admin Registered: 13 years ago Posts: 18,569 |
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
cat dts/kirkwood-nsa325.dtb >> zImage.fdt
bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000
bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x01100000 /boot/uInitrd; bootm $(loadaddr) 0x01100000
Re: NSA325V2 - Installation of Debian-4.4.0-kirkwood-tld-1-rootfs fails November 27, 2016 03:37AM |
Registered: 7 years ago Posts: 9 |
Re: NSA325V2 - Installation of Debian-4.4.0-kirkwood-tld-1-rootfs fails November 27, 2016 04:05AM |
Admin Registered: 13 years ago Posts: 18,569 |
Re: NSA325V2 - Installation of Debian-4.4.0-kirkwood-tld-1-rootfs fails November 29, 2016 03:41AM |
Registered: 7 years ago Posts: 9 |
setenv bootcmd_linux 'setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x01100000 /boot/uInitrd; bootm $(loadaddr) 0x01100000'
setenv 'bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8'