Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131)
Posted by helge
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 11, 2017 08:20PM |
Registered: 7 years ago Posts: 27 |
bodhi,
nope doesn't show up in my router nor in wireshark - with usb_boot
if i just let it run start (with bootcmd=tftpload...) and provide our uImage it seems to get further, because the nas appears in the router.
Edited 2 time(s). Last edit at 03/11/2017 08:35PM by helge.
nope doesn't show up in my router nor in wireshark - with usb_boot
if i just let it run start (with bootcmd=tftpload...) and provide our uImage it seems to get further, because the nas appears in the router.
Namme^ip^mac PC-10-0-0-30 10.0.0.30 00:50:43:00:02:02
Edited 2 time(s). Last edit at 03/11/2017 08:35PM by helge.
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 12, 2017 05:01PM |
Admin Registered: 13 years ago Posts: 18,543 |
helge,
> if i just let it run start (with bootcmd=tftpload.
> ..) and provide our uImage it seems to get further
> , because the nas appears in the router.
>
This is a very good sign! so can you ping the box with 10.0.0.30 ? do this about 2 minutes after it seems to get stuck. If it responses to ping then try to ssh in to see what is the behavior, whether it is actually running.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> if i just let it run start (with bootcmd=tftpload.
> ..) and provide our uImage it seems to get further
> , because the nas appears in the router.
>
> Namme^ip^mac > PC-10-0-0-30 10.0.0.30 00:50:43:00:02:02 >
This is a very good sign! so can you ping the box with 10.0.0.30 ? do this about 2 minutes after it seems to get stuck. If it responses to ping then try to ssh in to see what is the behavior, whether it is actually running.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 12, 2017 08:39PM |
Registered: 7 years ago Posts: 27 |
Nope there is no connectivity. But i found something near 0004f0a0 . I haven't seen this arguments in stock medion uboot nor after i did a resetenv. It's still badly formatted,because i did it manual
|_| .image_multi.Recovery imgage will be treated in multimode..Recovery imgage will be treated in normal mode..usbload.usb.0:1.loadaddr./multiware.img./flashware.img.Trying to load image from ||USB flash drive ||using FAT FS..Tr| |ying to load ima||ge from USB flas||h drive using ex||t2 FS partition ||0..0:0.Trying to| | load image from|| USB flash drive using ext2FS partition1..Couldn't load recovery image from USB flash drive, T||rying network in| |terface..filesiz| |e./upgrade.me.0x| |000000000.dummya| |ddr:%s..Multi:%s| |, Upgrade:%d..us| |b_upgrade.Aquiring an IP address using DHCP afte||r settling netwo| |rk.....DHCP shou| |ld be ready for|Recovery...Starting the Recovery process to retreive the image file.....Missing loadaddr environment variable as| |suming default (| |0x200000)!..0x200000.Update bootcmd..eth1addr setenv bootargs $(console) root=/dev/ram0 $(mvNetConfig) recovery=%s serverip=%d.%d.%d.%d ethact=$(ethact) ethaddr=%s eth1addr=%s; bootm $(loadaddr);.. bootcmd(recovery-image-multi):setenv bootargs $(console) root=/dev/ram0 $(mvNetConfig) rootfstype=squashfs initrd=0x%x,0x%x ramdisk_size=%d recovery=%s serverip=%d.%|d.%d.%d ethact=$(ethact) ethaddr=%s eth1addr=%s; bootm $(loadaddr); bootcmd(recovery-image-normal):console.console=ttyS0,115200 mtdparts=spi_flash:0x100000@0x0(uboot)ro,0x200000@0x100000(uimage),0xb80000@0x300000(rootfs),0x180000@0xe80000(varfs),0xf00000@0x100000(flash) varfs=/dev/mtdblock3 setenv bootargs $(console) rootfstype=squashfs root=/dev/mtdblock2 ;bootm 0xf8100000; setenv bootargs $(console) ubi.mtd=2 root=ubi0:rootfs rootfs type=ubifs $(mvNetConfig) $(mvPhoneConfig) $(lcd0_bootargs); nand read.e $(loadaddr) 0x100000 0x300000; bootm $(loadaddr); console=ttyS0,115200 setenv bootargs $(console) rootfs type=squashfs root=/dev/mtdblock2 $(mvNetConfig) $(mvPhoneConfig) $(lcd0_bootargs); nand read.e $(loadaddr) 0x100000 0x200000; bootm $(loadaddr);%d is RGMII..Module %d is GMII..M||odule %d is TS..||Module %d is MII||..Module %d is L||CD..console=ttyS| |0,115200 mtdpart| |s=nand_mtd:0x%x@| |0(uboot)ro,0x%x@| |0x%x(root).nandE| |nvBase.mainlineL| |inux.arcNumber.p| |exMode.EP.ep.sat| |a_dma_mode.MALLOC_len.ethprime.egiga1.egiga0.net| |bsd_en.netbsd_gw||.192.168.0.254 netbsd_mask=255.255.255.0 netbsd_fs=nfs netbsd_server=192.168.0.1 netbsd_ip=$(ipaddr) netbsd_rootdev.mgi0.netbsd_add.0x800000. netbsd_get.tftpboot $(| |netbsd_add) $(im| |age_name).netbsd| |_set_args.setenv| | bootargs nfsroo| |t=$(netbsd_serve| |r):$(rootpath) fs=$(netbsd_fs) ip=$(netbsd_ip) serverip=$(netbsd_server) mask=$(netbsd_mask) gw=$(netbsd_gw) rootdev=$(netbsd_rootdev) ethaddr=$(ethaddr) eth1addr=$(eth1addr) ethmtu=$(ethmtu) eth1mtu=$(eth1mtu) $(netbsd_netconfig).bootm $(netbsd_add) $(bootargs).netbsd_bootcmd.run netbsd_get ; run netbsd_set_args ; run netbsd_boot. vxworks_en.mgi(0,0)| | host:vxWorks.st.serverip. h=. e| |=.:ffff0000 u=anonymous pw=target .vxWorks_bootargs.bootargs_root.root=/dev/nfs rw.bootargs_end.| |:::orion:eth0:no| |ne.:::DB88FXX81:| |eth0:none.image_| |name.uImage.tftp| |boot 0x2000000 $| |(image_name); se| |tenv bootargs $(| |console) $(boota| |rgs_root) nfsroo| |t=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvNetConfig) $(mvPhoneConfig) video=dovefb:lcd0:$(lcd0_params) clcd.lcd0_enable=$(lcd0_enable); bootm 0x2000000; .standalone.fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;.lcd0_enable.lcd0_params.640x480-16@60.bootdelay.disaMvPnp.00:50:43:%02x:%02x:%02x.ethmtu.eth1mtu.mvPhoneConfig. mv_phone_config=dev[0]:fxs,dev[1]:fxo.mvNetConfig.mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr.00:00:00:EE:51:81 nandEcc=1bit .netretry. rcvrip.169.254.100.100. 0x02000000 .autoload.enaAutoRecovery.USB
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 12, 2017 11:59PM |
Admin Registered: 13 years ago Posts: 18,543 |
helge,
Is there a suport website where you can look for u-boot source code? or perhaps request it from the manufacturer?
We'd never know what they did in the code that could have changed the bootargs, or did similar things.
For example, if you look in the MVEBU kernel thread, NAS326 installation section:
http://forum.doozan.com/read.php?2,32146
In this NAS326 box, Zyxel actually had a hardcoded bootcmd (doh!). I could only control stock u-boot bootcmd after looking at their source code.
So we are basically blind without the GPL :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Is there a suport website where you can look for u-boot source code? or perhaps request it from the manufacturer?
We'd never know what they did in the code that could have changed the bootargs, or did similar things.
For example, if you look in the MVEBU kernel thread, NAS326 installation section:
http://forum.doozan.com/read.php?2,32146
In this NAS326 box, Zyxel actually had a hardcoded bootcmd (doh!). I could only control stock u-boot bootcmd after looking at their source code.
So we are basically blind without the GPL :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 13, 2017 02:14PM |
Registered: 7 years ago Posts: 27 |
Hi bodhi,
>Is there a suport website where you can look for u-boot source code? or perhaps request it from the manufacturer?
there is just a manual and a reset tool. The "manufacturer" is just one of those "i buy a bunch of devices and let the manufacturer label it with my name" company. Most of the times they just do wired stuff to the software, so its not working well and behaves different than stock software.
So our guess that they did something to bootrom or u-boot isn't that low ;)
But since they just resell stuff, i don't think they can/wan't to provide full source. But i'll write a mail to support.
But altough they do software sloppy, i also think they stick to GPL. SO i did some diging
€
I always wondered how they do internet reset. In:
Start_network really start network. SO lets look at get_recovery_script
---------------------------
#If we've reached this point /sbin/recovery_script has been downloaded
#so execute it
/sbin/recovery_script
--------------------------
Recovery script chrooting into downloaded and extracted recoveryfullfs.tar.gz calling init
As always i've uploaded all new files here. I am using my windows today so it had to be .zip
I also dont know yet what is in "sh" cause my windows wont extract it (symlinks...)
But as i googled some params. it seems to be the same on all storas SO nothing new for you :P
But than new hope rises. I was writing my mail to medion and decided to visit the FAQ
finding a FW Update
If you google that number you quickly find a forum, where the ftp server with a FW Update from 2012 is named
It didnt say kernel Update, just some Software Updats and "general" fixes
:
Edited 7 time(s). Last edit at 03/13/2017 06:53PM by helge.
>Is there a suport website where you can look for u-boot source code? or perhaps request it from the manufacturer?
there is just a manual and a reset tool. The "manufacturer" is just one of those "i buy a bunch of devices and let the manufacturer label it with my name" company. Most of the times they just do wired stuff to the software, so its not working well and behaves different than stock software.
So our guess that they did something to bootrom or u-boot isn't that low ;)
But since they just resell stuff, i don't think they can/wan't to provide full source. But i'll write a mail to support.
But altough they do software sloppy, i also think they stick to GPL. SO i did some diging
€
I always wondered how they do internet reset. In:
medionsource\recoveryfs\sbin\startrecovery #!/bin/sh echo "Recovery started..." /bin/led_indicator recovery-start #call the start_usb_burn to see if we can do everything from USB /sbin/start_usb_burnOk USB recovery. So lets have a look at that file:
cp /mnt/usb/recoveryfullfs.tar.gz /recoveryfullfs.tar.gz gunzip /recoveryfullfs.tar.gz tar xf /recoveryfullfs.tar #/dev needs to be populated for recoveryfullfs cd / tar c dev | tar x -C /recoveryfullfs echo "changing root to /recoveryfullfs" chroot /recoveryfullfs /initSo we need recoveryfullfs to proceed. Lets get back to "startrecovery"
echo "USB Reflash unsuccessful. Attempting online recovery" /sbin/start_network /sbin/get_recovery_scriptOh thats nice ONLINE.
Start_network really start network. SO lets look at get_recovery_script
wget -O /sbin/recovery_script -T 30 -t 1 -q \ http://recovery.medion.hipserv.com/downloads/recovery/get_recovery_script.php\Oha! so let's download recovery_script and have a look at it. (The other code in get_recovery_script is the same as in usb_burn)
wget -O /recoveryfullfs.tar.gz.....Now we have the file recoveryfullfs.tar.gz and start_recovery is calling downloaded recovery_script.
---------------------------
#If we've reached this point /sbin/recovery_script has been downloaded
#so execute it
/sbin/recovery_script
--------------------------
Recovery script chrooting into downloaded and extracted recoveryfullfs.tar.gz calling init
chroot /recoveryfullfs /initInit himself
flash_eraseall /dev/mtd2 wget http://recovery.medion.hipserv.com/downloads/recovery/get_firmware.php | ubiformat /dev/mtd2 -s 2048 -O 2048 -S $UBISIZE -f - ubiattach /dev/ubi_ctrl -m 2 -O 2048 mount -t ubifs ubi0:rootfs /mnt/ exec shGet_firmware downloads hipserv2_netgear-20111019.ubi which is indeed a ubifs
first bytes: UBI#############DOWNLOAD
As always i've uploaded all new files here. I am using my windows today so it had to be .zip
I also dont know yet what is in "sh" cause my windows wont extract it (symlinks...)
But as i googled some params. it seems to be the same on all storas SO nothing new for you :P
But than new hope rises. I was writing my mail to medion and decided to visit the FAQ
finding a FW Update
If you google that number you quickly find a forum, where the ftp server with a FW Update from 2012 is named
It didnt say kernel Update, just some Software Updats and "general" fixes
:
Edited 7 time(s). Last edit at 03/13/2017 06:53PM by helge.
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 16, 2017 07:47AM |
Admin Registered: 13 years ago Posts: 18,543 |
helge,
Let's hack our way in, slowly step by step
See if we get the kernel running at all.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/16/2017 07:48AM by bodhi.
Let's hack our way in, slowly step by step
setenv arcNumber 4931 setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200' setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv usb_boot 'usb start; run set_bootargs; run usb_load_uimage; run usb_load_uinitrd; bootm 0x800000 0x1100000' run usb_boot
See if we get the kernel running at all.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/16/2017 07:48AM by bodhi.
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 17, 2017 02:29PM |
Registered: 7 years ago Posts: 27 |
hi bodhi,
thanks for your reply. But it's behavior is still the same:
I've hooked up the device on a hub and connected it with my laptop running isc-dhcpd. I see 0 on my interface if we run custom kernel.
In the meanwhile (and before i even posted here) i tried openstoras kernel. The result is the same. In the wiki it says Medion Lifecloud 2-bay NAS supported
Edited 3 time(s). Last edit at 03/17/2017 02:34PM by helge.
thanks for your reply. But it's behavior is still the same:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB6702A-GMtech LE
U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz
DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv arcNumber 4931
Marvell>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200'
Marvell>> setenv mainlineLinux yes
Marvell>> setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'usb start; run set_bootargs; run usb_load_uimage; run usb_load_uinitrd; bootm 0x800000 0x1100000'
Marvell>> run usb
usb_load_uImage usb_load_uInitrd usb_cmd usb_bootargs usb0Mode
usb_load_uimage usb_load_uinitrd usb_boot
Marvell>> run usb_boot
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................
2878838 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
...............................................................................................................................................................................................................................
6535284 bytes read
## Booting image at 00800000 ...
Image Name: bla3185-320
Created: 2017-03-12 16:51:34 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2878774 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-3.18.5-kirkwood-tld-1
Created: 2015-02-19 1:49:36 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6535220 Bytes = 6.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
I've hooked up the device on a hub and connected it with my laptop running isc-dhcpd. I see 0 on my interface if we run custom kernel.
In the meanwhile (and before i even posted here) i tried openstoras kernel. The result is the same. In the wiki it says Medion Lifecloud 2-bay NAS supported
Edited 3 time(s). Last edit at 03/17/2017 02:34PM by helge.
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 17, 2017 04:35PM |
Admin Registered: 13 years ago Posts: 18,543 |
helge,
If the bootargs is that simple and we could not get it to run, most likely the DTB is wrong one.
These have the same SoCs:
NSA310S
NSA320S
Pogo V4
So perhaps we want to try all 3.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
If the bootargs is that simple and we could not get it to run, most likely the DTB is wrong one.
These have the same SoCs:
NSA310S
NSA320S
Pogo V4
So perhaps we want to try all 3.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 24, 2017 05:38PM |
Registered: 8 years ago Posts: 295 |
same here .. tested with all mentioned DTBs ..
my kirkwood kernel builds
my oxnas kernel builds
Tvheadend Kirkwood Debian packages
my kirkwood devices:
- 1x hp t5325 (1,2 GHz, 88F6281 / 512 MB / 4x USB)
my oxnas devices
- 2x pogoplug
my dove devices
- 2x Chip PC LXD8541 (800 MHz, 88F510 / 1024 MB / 6x USB)
- 1x Wyse T50 (1,0 GHz, 88F510 / 1024 MB / 4x USB)
my amlogic devices
- several s905x / s912 devices
my x86 devices
Dell Optiplex 3020 (3,4 GHz, 2C/4T / Haswell / 4096 MB 2x Intel I210 / PicoPSU)
PC 1: (ASRock Z390 itx/ac / i3-8100, 3,6 GHZ, 2C / 4T / 32 GB RAM / Nanum SE-P180Q
PC 2: (ASRock Fatal1ty X470 Gaming-ITX/ac / Ryzen 5 2600, 3,4 GHz, 6C 12T / 32 GB RAM / Radeon RX550 2 GB / Be Quiet! BN229
my kirkwood kernel builds
my oxnas kernel builds
Tvheadend Kirkwood Debian packages
my kirkwood devices:
- 1x hp t5325 (1,2 GHz, 88F6281 / 512 MB / 4x USB)
my oxnas devices
- 2x pogoplug
my dove devices
- 2x Chip PC LXD8541 (800 MHz, 88F510 / 1024 MB / 6x USB)
- 1x Wyse T50 (1,0 GHz, 88F510 / 1024 MB / 4x USB)
my amlogic devices
- several s905x / s912 devices
my x86 devices
Dell Optiplex 3020 (3,4 GHz, 2C/4T / Haswell / 4096 MB 2x Intel I210 / PicoPSU)
PC 1: (ASRock Z390 itx/ac / i3-8100, 3,6 GHZ, 2C / 4T / 32 GB RAM / Nanum SE-P180Q
PC 2: (ASRock Fatal1ty X470 Gaming-ITX/ac / Ryzen 5 2600, 3,4 GHz, 6C 12T / 32 GB RAM / Radeon RX550 2 GB / Be Quiet! BN229
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 27, 2017 12:56PM |
Registered: 7 years ago Posts: 27 |
hi bodhi,
hi pengu,
i confirm that the device won't boot with the mentioned DTB. As always without a response.
@pengu
Have you seen the "strange" broadcasts the Medion NAS does while in Recovery? Its shouting "Hail dictator-of-germany-'till-1945"... in my network oO
Edited 4 time(s). Last edit at 03/27/2017 02:02PM by helge.
hi pengu,
i confirm that the device won't boot with the mentioned DTB. As always without a response.
@pengu
Have you seen the "strange" broadcasts the Medion NAS does while in Recovery? Its shouting "Hail dictator-of-germany-'till-1945"... in my network oO
Edited 4 time(s). Last edit at 03/27/2017 02:02PM by helge.
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 28, 2017 01:31AM |
Admin Registered: 13 years ago Posts: 18,543 |
helge,
> Its shouting "Hail dic
> tator-of-germany-'till-1945"... in my network oO
Haha :) some sick joke.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Its shouting "Hail dic
> tator-of-germany-'till-1945"... in my network oO
Haha :) some sick joke.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 28, 2017 01:38AM |
Admin Registered: 13 years ago Posts: 18,543 |
helge,
Here is another approach. Let's try booting a non-FDT kernel. This is the rootfs that has non-FDT kernel.
And then you would want to set arcNumber and machid to the correct values for Pogo V4 in serial console:
The rest of the envs are exactly as before.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Here is another approach. Let's try booting a non-FDT kernel. This is the rootfs that has non-FDT kernel.
Updated 02 Sept 2014 (rootfs): Rootfs Debian-3.16.0-kirkwood-tld-2 was uploaded. This rootfs is to keep in sync with kernel Linux-3.16.0-kirkwood-tld-2 (and its new features).
And then you would want to set arcNumber and machid to the correct values for Pogo V4 in serial console:
setenv arcNumber 3960 setenv machid f78
The rest of the envs are exactly as before.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 28, 2017 03:26AM |
Registered: 7 years ago Posts: 27 |
bodhi Wrote:
-------------------------------------------------------
> helge,
>
> > Its shouting "Hail dic
> > tator-of-germany-'till-1945"... in my network oO
>
> Haha :) some sick joke.
The tech guy has a bad sense of humor :P
I've confronted Medion with my Wireshark "Hail..." Packets. Lets see if they respond with U-boot code :D
-------------------------------------------------------
> helge,
>
> > Its shouting "Hail dic
> > tator-of-germany-'till-1945"... in my network oO
>
> Haha :) some sick joke.
The tech guy has a bad sense of humor :P
I've confronted Medion with my Wireshark "Hail..." Packets. Lets see if they respond with U-boot code :D
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 30, 2017 06:14AM |
Registered: 8 years ago Posts: 295 |
same as before..
and with the last known version of the kernel 3.16 ..
The LEDs indicate that there is some more stuff going on as with kernel 3.18.5 ..
The green one keeps blinking for one second then .. the red one is lighting up ..
With Kernel 3.18.5 ... only the blue LEDs lights up
Edited 2 time(s). Last edit at 03/30/2017 01:31PM by pengu.
... USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found reading /uImage ............................................................................................................................................................. 2756040 bytes read reading /uInitrd ............................................................................................................................................................. 6032465 bytes read ## Booting image at 00800000 ... Image Name: Linux-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2755976 Bytes = 2.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6032401 Bytes = 5.8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
and with the last known version of the kernel 3.16 ..
... USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found reading /uImage ........................................................................................................................................................... 2786896 bytes read reading /uInitrd ........................................................................................................................................................... 6308708 bytes read ## Booting image at 00800000 ... Image Name: vmlinuz-3.16.42-kirkwood-tld-3 Created: 2017-03-30 18:07:50 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2786832 Bytes = 2.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-3.16.42-kirkwood-tld-3 Created: 2017-03-30 18:08:26 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6308644 Bytes = 6 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
The LEDs indicate that there is some more stuff going on as with kernel 3.18.5 ..
The green one keeps blinking for one second then .. the red one is lighting up ..
With Kernel 3.18.5 ... only the blue LEDs lights up
Edited 2 time(s). Last edit at 03/30/2017 01:31PM by pengu.
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 30, 2017 02:55PM |
Admin Registered: 13 years ago Posts: 18,543 |
pengu Wrote:
-------------------------------------------------------
> same as before..
>
>
> and with the last known version of the kernel 3.16
> ..
>
>
> The LEDs indicate that there is some more stuff go
> ing on as with kernel 3.18.5 ..
>
> The green one keeps blinking for one second then .
> . the red one is lighting up ..
> With Kernel 3.18.5 ... only the blue LEDs lights u
> p
pengu,
Do you have earlyprintk=serial bootargs set in this run?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> same as before..
>
>
> ... > > USB 0: host mode > PEX 0: PCI Express Root Complex Interface > PEX interface detected Link X1 > Net: egiga0 [PRIME] > Hit any key to stop autoboot: 0 > (Re)start USB... > USB: scanning bus for devices... 2 USB Device(s) > found > Waiting for storage device(s) to settle before sca > nning... > 1 Storage Device(s) found > reading /uImage > .................................................. > .................................................. > .................................................. > ....... > > 2756040 bytes read > reading /uInitrd > .................................................. > .................................................. > .................................................. > ....... > > 6032465 bytes read > ## Booting image at 00800000 ... > Image Name: Linux-3.16.0-kirkwood-tld-2 > Created: 2014-09-01 23:18:31 UTC > Image Type: ARM Linux Kernel Image (uncompres > sed) > Data Size: 2755976 Bytes = 2.6 MB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > OK > ## Loading Ramdisk Image at 01100000 ... > Image Name: initramfs-3.16.0-kirkwood-tld-2 > Created: 2014-09-01 23:18:48 UTC > Image Type: ARM Linux RAMDisk Image (gzip com > pressed) > Data Size: 6032401 Bytes = 5.8 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > > Starting kernel ... > > >>
> and with the last known version of the kernel 3.16
> ..
>
>
> ... > USB 0: host mode > PEX 0: PCI Express Root Complex Interface > PEX interface detected Link X1 > Net: egiga0 [PRIME] > Hit any key to stop autoboot: 0 > (Re)start USB... > USB: scanning bus for devices... 2 USB Device(s) > found > Waiting for storage device(s) to settle before sca > nning... > 1 Storage Device(s) found > reading /uImage > .................................................. > .................................................. > .................................................. > ..... > > 2786896 bytes read > reading /uInitrd > .................................................. > .................................................. > .................................................. > ..... > > 6308708 bytes read > ## Booting image at 00800000 ... > Image Name: vmlinuz-3.16.42-kirkwood-tld-3 > Created: 2017-03-30 18:07:50 UTC > Image Type: ARM Linux Kernel Image (uncompres > sed) > Data Size: 2786832 Bytes = 2.7 MB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > OK > ## Loading Ramdisk Image at 01100000 ... > Image Name: initramfs-3.16.42-kirkwood-tld-3 > Created: 2017-03-30 18:08:26 UTC > Image Type: ARM Linux RAMDisk Image (gzip com > pressed) > Data Size: 6308644 Bytes = 6 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > > Starting kernel ... > > >>
> The LEDs indicate that there is some more stuff go
> ing on as with kernel 3.18.5 ..
>
> The green one keeps blinking for one second then .
> . the red one is lighting up ..
> With Kernel 3.18.5 ... only the blue LEDs lights u
> p
pengu,
Do you have earlyprintk=serial bootargs set in this run?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 30, 2017 03:27PM |
Registered: 8 years ago Posts: 295 |
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 30, 2017 05:46PM |
Admin Registered: 13 years ago Posts: 18,543 |
pengu Wrote:
-------------------------------------------------------
> ok .. same as before .. nothing more ..
> (tested with linux-3.16.42 and linux-4.4.6)
What is your u-boot envs or kernel load addresses? did you try both stock addresses and our convetional 0x8000000 ?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> ok .. same as before .. nothing more ..
> (tested with linux-3.16.42 and linux-4.4.6)
What is your u-boot envs or kernel load addresses? did you try both stock addresses and our convetional 0x8000000 ?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) March 31, 2017 11:01AM |
Registered: 7 years ago Posts: 27 |
bodhi Wrote:
-------------------------------------------------------
> pengu Wrote:
> --------------------------------------------------
> -----
> > ok .. same as before .. nothing more ..
> > (tested with linux-3.16.42 and linux-4.4.6)
>
>
> What is your u-boot envs or kernel load addresses?
> did you try both stock addresses and our convetion
> al 0x8000000 ?
## Booting image at 00800000 .
## Loading Ramdisk Image at 01100000 ...
seems like he used 0x800000 for uImage and 0x1100000 for uInitrd.
Medions first reply doesn't look very promising. They just send me a mail, with a link where i should search for the source. They didn't even provided a direct link :P
But it took them four buisness days to respond....
Edited 2 time(s). Last edit at 03/31/2017 04:26PM by helge.
-------------------------------------------------------
> pengu Wrote:
> --------------------------------------------------
> -----
> > ok .. same as before .. nothing more ..
> > (tested with linux-3.16.42 and linux-4.4.6)
>
>
> What is your u-boot envs or kernel load addresses?
> did you try both stock addresses and our convetion
> al 0x8000000 ?
## Booting image at 00800000 .
## Loading Ramdisk Image at 01100000 ...
seems like he used 0x800000 for uImage and 0x1100000 for uInitrd.
Medions first reply doesn't look very promising. They just send me a mail, with a link where i should search for the source. They didn't even provided a direct link :P
But it took them four buisness days to respond....
Edited 2 time(s). Last edit at 03/31/2017 04:26PM by helge.
|
jonrv
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 07, 2017 04:50AM |
This is not exactly fitting the topic, but I use the same device and need help.
I think I bricked the board with a wrong u-boot (no leds except the green network one).
Sadly it seems that kwboot isn't working, so I think my last chance is the JTAG connector.
But to make it boot, I need a copy of the original/a working u-boot (stupidly I thought I'm much cleverer than anyone else and didn't make a backup). I don't want to buy a JTAG connector without an image of a working u-boot, so maybe someone, especially helge, could upload one.
Thanks for your help, jonrv
I think I bricked the board with a wrong u-boot (no leds except the green network one).
Sadly it seems that kwboot isn't working, so I think my last chance is the JTAG connector.
But to make it boot, I need a copy of the original/a working u-boot (stupidly I thought I'm much cleverer than anyone else and didn't make a backup). I don't want to buy a JTAG connector without an image of a working u-boot, so maybe someone, especially helge, could upload one.
Thanks for your help, jonrv
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 08, 2017 10:14AM |
Registered: 7 years ago Posts: 27 |
|
jonrv
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 12, 2017 07:58AM |
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 17, 2017 04:52PM |
Registered: 7 years ago Posts: 27 |
|
jonrv
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 20, 2017 08:39AM |
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 30, 2017 03:25AM |
Registered: 7 years ago Posts: 27 |
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 30, 2017 03:44PM |
Registered: 8 years ago Posts: 295 |
yes, this seems the only working "envs"
other than gives gives me a
when changing the the load adress(es) to other than default, I get this when loading the initrd
Edited 2 time(s). Last edit at 06/05/2017 05:03PM by pengu.
other than gives gives me a
pc : [<0064c700>] lr : [<00620da0>] sp : 005fb1d0 ip : 00000003 fp : 00000002 r10: 00690c80 r9 : 00000001 r8 : 005fffcc r7 : dc87b18b r6 : c19c3a76 r5 : 93e75275 r4 : 00000000 r3 : 00000080 r2 : 006cf9c0 r1 : 000f4240 r0 : 00000001 Flags: nZcv IRQs off FIQs off Mode SVC_32 Resetting CPU ...
when changing the the load adress(es) to other than default, I get this when loading the initrd
Edited 2 time(s). Last edit at 06/05/2017 05:03PM by pengu.
|
Re: Deb on Medion MD86783 (Soc: 88F6702 Marvell Feroceon 88FR131) May 30, 2017 04:08PM |
Admin Registered: 13 years ago Posts: 18,543 |
pengu Wrote:
-------------------------------------------------------
> yes, this seems the only working "envs"
>
> other than ghis gives me a
>
>
Sorry, I don't understand what you are saying. Can you be more specific? and quote the previous post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> yes, this seems the only working "envs"
>
> other than ghis gives me a
>
>
> pc : [<0064c700>] lr : [<00620da0>] > sp : 005fb1d0 ip : 00000003 fp : 00000002 > r10: 00690c80 r9 : 00000001 r8 : 005fffcc > r7 : dc87b18b r6 : c19c3a76 r5 : 93e75275 r4 > : 00000000 > r3 : 00000080 r2 : 006cf9c0 r1 : 000f4240 r0 > : 00000001 > Flags: nZcv IRQs off FIQs off Mode SVC_32 > Resetting CPU ... >
Sorry, I don't understand what you are saying. Can you be more specific? and quote the previous post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
