Debian on Lenovo ix2-dl

| \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** ix2-nand ** ** uboot_ver:0.0.8 ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Oct 28 2011 - 15:19:29) Marvell version: 3.6.1 - EMC U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:1024 MB Found ADT7473, program PWM1 ... OK Flash: 0 kB Marvell Serial ATA Adapter Integrated Sata device found CPU : Marvell Feroceon (Rev 1) Found kernel at 0x100000 Found initrd at 0x400000 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. PEX 1: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0

setenv load_initrd 'fatload usb 0:1 0x1100000 /uInitrd' setenv load_uimage 'fatload usb 0:1 0x800000 /uImage' setenv rootdelay 4 setenv rootfstype ext4 setenv usb_root 'LABEL=rootfs' setenv bootcmd 'run usb_boot' setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000' setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootfstype=ext4 mtdparts=orion_nand:0x100000@0(uboot)ro,0x20000@0xA0000(uboot_env)'

(Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found reading /uImage ................................................................................................................................................. 3223931 bytes read reading /uInitrd ................................................................................................................................................. 6824496 bytes read ## Booting image at 00800000 ... Image Name: vmlinuz-4.9.30-kirkwood-rm-1 Created: 2017-06-05 10:33:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3223867 Bytes = 3.1 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initrd.img-4.9.30-kirkwood-rm-1 Created: 2017-06-05 10:33:35 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6824432 Bytes = 6.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.30-kirkwood-rm-1 (root@iConnectTV) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sun Jun 4 01:56:52 CEST 207 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt:Machine model: Lenovo IX2-ng ...

sensors adt7473-i2c-0-2e Adapter: mv64xxx_i2c adapter in1: +1.10 V (min = +0.00 V, max = +2.99 V) +3.3V: +3.32 V (min = +2.96 V, max = +3.61 V) fan1: 793 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) temp1: +49.2°C (low = -63.0°C, high = +191.0°C) (crit = +100.0°C, hyst = +96.0°C) Board Temp: +44.2°C (low = -63.0°C, high = +191.0°C) (crit = +100.0°C, hyst = +96.0°C) temp3: +41.5°C (low = -63.0°C, high = +191.0°C) (crit = +100.0°C, hyst = +96.0°C) kirkwood_thermal-virtual-0 Adapter: Virtual device temp1: +52.1°C

cat /proc/cpuinfo processor : 0 model name : Feroceon 88FR131 rev 1 (v5l) BogoMIPS : 1580.03 Features : swp half thumb fastmult edsp CPU implementer : 0x56 CPU architecture: 5TE CPU variant : 0x2 CPU part : 0x131 CPU revision : 1 Hardware : Marvell Kirkwood (Flattened Device Tree) Revision : 0000 Serial : 0000000000000000

free -m total used free shared buff/cache available Mem: 244 19 198 1 27 215 Swap: 255 9 246

... [ 140.124718] systemd-shutdown[1]: Sending SIGTERM to remaining processes... [ 140.143270] systemd-journald[205]: Received SIGTERM from PID 1 (systemd-shutdow). [ 140.166077] systemd-shutdown[1]: Sending SIGKILL to remaining processes... [ 140.183355] systemd-shutdown[1]: Unmounting file systems. [ 140.189888] systemd-shutdown[1]: Remounting '/' read-only with options 'data=ordered'. [ 140.223809] EXT4-fs (sda3): re-mounted. Opts: data=ordered [ 140.240940] systemd-shutdown[1]: Remounting '/' read-only with options 'data=ordered'. [ 140.249216] EXT4-fs (sda3): re-mounted. Opts: data=ordered [ 140.254837] systemd-shutdown[1]: All filesystems unmounted. [ 140.260483] systemd-shutdown[1]: Deactivating swaps. [ 140.265657] systemd-shutdown[1]: All swaps deactivated. [ 140.270977] systemd-shutdown[1]: Detaching loop devices. [ 140.280240] systemd-shutdown[1]: All loop devices detached. [ 140.384774] reboot: System halted

pengu Wrote:
-------------------------------------------------------
> This device is similar to some ZyXEL devices
> (NSA325v2 / NSA310s / NSA320s) 
> so it has similar issues (power off)
> This is why I gave away my first device last year.
> 
> A view months ago I noticed that this issue is
> gone since Kernel 4.8 on other devices, let's try
> on this device too.
> I also noticed that there was introduced a new DTB
> in Kernel 4.10 for the, I think similar device
> "Lenovo ix2-ng".
> 
> [code]
>        |  \/  | __ _ _ ____   _____| | |
>         | |\/| |/ _` | '__\ \ / / _ \ | |
>         | |  | | (_| | |   \ V /  __/ | |
>         |_|  |_|\__,_|_|    \_/ \___|_|_|
>  _   _     ____              _
> | | | |   | __ )  ___   ___ | |_ 
> | | | |___|  _ \ / _ \ / _ \| __| 
> | |_| |___| |_) | (_) | (_) | |_ 
>  \___/    |____/ \___/ \___/ \__|  ** ix2-nand **
> ** uboot_ver:0.0.8 **
> 
>  ** MARVELL BOARD: DB-88F6282A-BP LE 
> 
> U-Boot 1.1.4 (Oct 28 2011 - 15:19:29) Marvell
> version: 3.6.1 - EMC
> 
> U-Boot code: 00600000 -> 0067FFF0  BSS: ->
> 006CFB00
> 
> Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @
> 533Mhz
> SysClock = 533Mhz , TClock = 200Mhz 
> 
> DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20
> tRCD=7
> DRAM CS[0] base 0x00000000   size 256MB 
> DRAM Total size 256MB  16bit width
> Addresses 8M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (8M - 7M): Done
> NAND:1024 MB
> Found ADT7473, program PWM1 ... OK
> Flash:  0 kB
> 
> Marvell Serial ATA Adapter
> Integrated Sata device found
> 
> 
> CPU : Marvell Feroceon (Rev 1)
> Found kernel at 0x100000
> Found initrd at 0x400000
> 
> Streaming disabled 
> Write allocate disabled
> 
> 
> USB 0: host mode
> PEX 0: interface detected no Link.
> PEX 1: interface detected no Link.
> Net:   egiga0 [PRIME]
> Hit any key to stop autoboot:  0 
> [/code]
> 
> So I changed the U-Boot env as usual to boot from
> USB:
> Note: adopted from the iomega / lennovo ix2-200
> 
> [code]
> setenv load_initrd 'fatload usb 0:1 0x1100000
> /uInitrd'                                         
>                                                   
>                                                  
> setenv load_uimage 'fatload usb 0:1 0x800000
> /uImage'                                          
>                                                   
>                                                  
> 
> setenv rootdelay 4                                
>                                                   
>                                                   
>                                           
> setenv rootfstype ext4                            
>                                                   
>                                                   
>                                           
> setenv usb_root 'LABEL=rootfs'                    
>                                                   
>                                                   
>                                             
> setenv bootcmd 'run usb_boot'                     
>                                                   
>                                                   
>                                            
>                                                   
>                                                   
>                                                   
>                    
> setenv usb_boot 'usb start; run load_uimage; run
> load_initrd; bootm 0x800000 0x1100000'            
>                                                   
>                                                   
>                                                   
>           
> setenv bootargs 'console=ttyS0,115200
> root=LABEL=rootfs rootfstype=ext4
> mtdparts=orion_nand:0x100000@0(uboot)ro,0x20000@0xA0000(uboot_env)'
> 
> [/code]
> 
> Because this U-Boot doesn't know about DTBs I had
> to append it.
> 
> Note: you can also use the ix2-200 one but with
> this you get strange NAND error messages, sensors
> were not working and with the new device .. no
> serial output after the kernel is loaded.
> so we will proceed with the ix2-ng DTB:
> 
> [code]
> 
> (Re)start USB...
> USB:   scanning bus for devices... 3 USB Device(s)
> found
> Waiting for storage device(s) to settle before
> scanning...
> 1 Storage Device(s) found
> 
> reading /uImage
> .................................................................................................................................................
> 
> 3223931 bytes read
> reading /uInitrd
> .................................................................................................................................................
> 
> 6824496 bytes read
> ## Booting image at 00800000 ...
>    Image Name:   vmlinuz-4.9.30-kirkwood-rm-1
>    Created:      2017-06-05  10:33:02 UTC
>    Image Type:   ARM Linux Kernel Image
> (uncompressed)
>    Data Size:    3223867 Bytes =  3.1 MB
>    Load Address: 00008000
>    Entry Point:  00008000
>    Verifying Checksum ... OK
> OK
> ## Loading Ramdisk Image at 01100000 ...
>    Image Name:   initrd.img-4.9.30-kirkwood-rm-1
>    Created:      2017-06-05  10:33:35 UTC
>    Image Type:   ARM Linux RAMDisk Image (gzip
> compressed)
>    Data Size:    6824432 Bytes =  6.5 MB
>    Load Address: 00000000
>    Entry Point:  00000000
>    Verifying Checksum ... OK
> 
> Starting kernel ...
> 
> [    0.000000] Booting Linux on physical CPU 0x0
> [    0.000000] Linux version 4.9.30-kirkwood-rm-1
> (root@iConnectTV) (gcc version 4.9.2 (Debian
> 4.9.2-10) ) #1 PREEMPT Sun Jun 4 01:56:52 CEST
> 207
> [    0.000000] CPU: Feroceon 88FR131 [56251311]
> revision 1 (ARMv5TE), cr=0005397f
> [    0.000000] CPU: VIVT data cache, VIVT
> instruction cache
> [    0.000000] OF: fdt:Machine model: Lenovo
> IX2-ng
> ...
> [/code]
> 
> [url=https://pastebin.com/ikjBQTGq]serial
> bootlog[/url]
> 
> [url=https://pastebin.com/Gky7NMYY]dmesg
> output[/url]
> 
> sensors working:
> 
> [code]
> sensors
> adt7473-i2c-0-2e
> Adapter: mv64xxx_i2c adapter
> in1:          +1.10 V  (min =  +0.00 V, max = 
> +2.99 V)
> +3.3V:        +3.32 V  (min =  +2.96 V, max = 
> +3.61 V)
> fan1:         793 RPM  (min =    0 RPM)
> fan2:           0 RPM  (min =    0 RPM)
> fan3:           0 RPM  (min =    0 RPM)
> fan4:           0 RPM  (min =    0 RPM)
> temp1:        +49.2°C  (low  = -63.0°C, high =
> +191.0°C)
>                        (crit = +100.0°C, hyst =
> +96.0°C)
> Board Temp:   +44.2°C  (low  = -63.0°C, high =
> +191.0°C)
>                        (crit = +100.0°C, hyst =
> +96.0°C)
> temp3:        +41.5°C  (low  = -63.0°C, high =
> +191.0°C)
>                        (crit = +100.0°C, hyst =
> +96.0°C)
> 
> kirkwood_thermal-virtual-0
> Adapter: Virtual device
> temp1:        +52.1°C 
> 
> [/code]
> 
> [code]
>  cat /proc/cpuinfo 
> processor	: 0
> model name	: Feroceon 88FR131 rev 1 (v5l)
> BogoMIPS	: 1580.03
> Features	: swp half thumb fastmult edsp 
> CPU implementer	: 0x56
> CPU architecture: 5TE
> CPU variant	: 0x2
> CPU part	: 0x131
> CPU revision	: 1
> 
> Hardware	: Marvell Kirkwood (Flattened Device
> Tree)
> Revision	: 0000
> Serial		: 0000000000000000
> [/code]
> [code]
> free -m
>               total        used        free     
> shared  buff/cache   available
> Mem:            244          19         198       
>    1          27         215
> Swap:           255           9         246
> 
> [/code]
> 
> Note:
> 
> Now I tried to power the device off to see whats
> happening:
> 
> [code]
> ...
> [  140.124718] systemd-shutdown[1]: Sending
> SIGTERM to remaining processes...
> [  140.143270] systemd-journald[205]: Received
> SIGTERM from PID 1 (systemd-shutdow).
> [  140.166077] systemd-shutdown[1]: Sending
> SIGKILL to remaining processes...
> [  140.183355] systemd-shutdown[1]: Unmounting
> file systems.
> [  140.189888] systemd-shutdown[1]: Remounting '/'
> read-only with options 'data=ordered'.
> [  140.223809] EXT4-fs (sda3): re-mounted. Opts:
> data=ordered
> [  140.240940] systemd-shutdown[1]: Remounting '/'
> read-only with options 'data=ordered'.
> [  140.249216] EXT4-fs (sda3): re-mounted. Opts:
> data=ordered
> [  140.254837] systemd-shutdown[1]: All
> filesystems unmounted.
> [  140.260483] systemd-shutdown[1]: Deactivating
> swaps.
> [  140.265657] systemd-shutdown[1]: All swaps
> deactivated.
> [  140.270977] systemd-shutdown[1]: Detaching loop
> devices.
> [  140.280240] systemd-shutdown[1]: All loop
> devices detached.
> [  140.384774] reboot: System halted
> [/code]
> 
> ok .. no error messages but the fan is still
> running and the device is still consuming power
> confirmed with different kernel versions
> 
> Edit
> 
> with the 4.4.0 rootfs and 4.11.3 kernel ..
> poweroff seems to work completely .. perhaps this
> is systemd related ..
> 
> [url=https://pastebin.com/aYf0FNJ9]serial
> log[/url]
> 
> working on debian stretch too, see
> [url=https://pastebin.com/GbGcAK8c]here[/url]