Welcome! Log In Create A New Profile

Advanced

Lenovo iomega EZ support

Posted by eine 
Re: Lenovo iomega EZ support
July 19, 2017 12:26AM
sarcastic.mannequin Wrote:
-------------------------------------------------------
> Eine!
>
> Ugh. No fan. Disk gets too hot to touch? Ouch! Don
> 't use a 7200 rpm hard drive in it, that's for sur
> e! Why does the stock firmware survive?

:) With a HDD inside the enclosure and no fan, this box is destined to be in a short life.

> I'll check the Marvell Kirkwood thermal driver to
> see if it has the ability to slowdown the CPU or d
> o a shutdown if it gets in panic state. It might b
> e worth having a look for any other temperature se
> nsors on the board. Use either your eyes or use i2
> c-tools/lm-sensors to scan for sensors.

kirkwood thermal is in the kernel. But sometime it can not be used and i2c tool is needed.

> Might have
> to create a script to monitor temp and do controll
> ed shutdown or ???
> ll this assuming it is thermal related issue.

Yes, it is likely needed because thermal will be an issue. It seems a case mod is needed, even a thermal sensor is in it.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Lenovo iomega EZ support
July 19, 2017 01:19PM
Eine!

I checked Marvell Kirkwood thermal driver. It doesn't do anything but monitor the temp of the CPU.

Using stock Debian kernel (stretch):
Linux mnemotest 4.9.0-3-marvell #1 Debian 4.9.30-2+deb9u2 (2017-06-26) armv5tel GNU/Linux
I ran my IX2-ng box for about 1 hour with your script:
dd if=/dev/sda of=/dev/null bs=1MiB &
dd if=/dev/urandom of=/dev/null bs=1MiB &

No problems with shutting down. Here is the temp readings:
root@mnemotest:~# sensors
kirkwood_thermal-virtual-0
Adapter: Virtual device
temp1:        +69.0°C  

adt7473-i2c-0-2e
Adapter: mv64xxx_i2c adapter
in1:          +1.11 V  (min =  +0.00 V, max =  +2.99 V)
+3.3V:        +3.36 V  (min =  +2.96 V, max =  +3.61 V)
fan1:        3087 RPM  (min =    0 RPM)
fan2:           0 RPM  (min =    0 RPM)
fan3:           0 RPM  (min =    0 RPM)
fan4:           0 RPM  (min =    0 RPM)
temp1:        +48.2°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)
Board Temp:   +46.0°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)
temp3:        +42.5°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)

smartctl -a /dev/sda1 reports:
194 Temperature_Celsius     0x0022   110   104   000    Old_age   Always       -       37

So nice and cool here and no problems. But if your box works with stock firmware, then it maybe isn't related to thermal issues? I dunno.
Re: Lenovo iomega EZ support
July 20, 2017 05:50AM
bodhi, sarcastic.mannequin

Thank you for answer. I ordered new more powerful power supply 3A/12V instead 2A (2 years old). I am going to replace it along with HDD and try again.

bodhi Wrote:
-------------------------------------------------------
> sarcastic.mannequin Wrote:
> --------------------------------------------------
> -----
> > Eine!
> >
> > Ugh. No fan. Disk gets too hot to touch? Ouch! Don't use a 7200 rpm hard drive in it, that's for sure!
> > Why does the stock firmware survive?
>
> :) With a HDD inside the enclosure and no fan, this box is destined to be in a short life.

Well, I've got data which says otherwise. Currently my clients own 6 units. Oldest has about 3 years. Those works 24/7 for backup purposes. None of them died. I killed hard drive once because of swapping, ext2 filesystem contained ~ 10^7 files.

> > I'll check the Marvell Kirkwood thermal driver to
> > see if it has the ability to slowdown the CPU or
> > do a shutdown if it gets in panic state. It might
> > be worth having a look for any other temperature
> > sensors on the board. Use either your eyes or use i2
> > c-tools/lm-sensors to scan for sensors.
>
> kirkwood thermal is in the kernel. But sometime it
> can not be used and i2c tool is needed.
>
> > Might have
> > to create a script to monitor temp and do controlled shutdown or ???
> > ll this assuming it is thermal related issue.
>
> Yes, it is likely needed because thermal will be an issue. It seems a case mod is needed,
> even a thermal sensor is in it.

My plan is to rule thermal issue too. Put the disk outside, and install the fan to cool down the CPU.



Edited 3 time(s). Last edit at 07/20/2017 09:30AM by eine.
Re: Lenovo iomega EZ support
July 20, 2017 11:37AM
Eine!

Here they mention the temperatures of CPU and board. There must be another temp sensor somewhere.

Anandech EZ Media review
iomega ez
Re: Lenovo iomega EZ support
July 25, 2017 03:35AM
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST31500341AS                             Firm: CC71     Ser#:                           9VS3G04B
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST31500341AS                             Firm: CC71     Ser#:                           9VS3G04B
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512)

(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
................................................................................              ......................
................................................................................              ................................................................................              .........

3834687 bytes read
....
.
......
............
.........................
...................................................
................................................................................              ......................
................................................................................              ................................................................................              ............................................
....
................................................................................              ................................................................................              ................................................................................              .....................................................

7245696 bytes read
## Booting image at 00040000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2017-07-25   7:14:43 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3834623 Bytes =  3.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes =  6.9 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Thanks for update debian9.

but it fail to boot. just stop here

I tried reboot and here is printenv

        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST31500341AS                             Firm: CC71     Ser#:                           9VS3G04B
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/m              tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x20              00000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7              e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix1
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x180              0; bootm 0x40000 0x900000;
uboot_ver=0.0.8
fw_ver=3.3.2.29823
serial_number=5563Z01001G30100784J0C1
ethaddr=00:D0:B8:14:0B:8A
serialNo=USAD020062
modelname=31997701
serialno=0,01xqV5lWlCJ4voSqhRSkfcpHpi7vDAgRqVwyNe4nzWGO1eGJjRJi8ltftT1y38RqWc,US              AD020062,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX1/1.0.4/download_runin.sh
pre_path_conf=IX1/1.0.4/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX1/1.0.4
serverip=192.168.32.4
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
bootcmd1=ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; setenv               bootargs $(console) $(bootargs_root) $(bootargs_mtd) $(bootargs_end); bootm 0x40              000 0x900000;run bootcmd2
bootcmd=ide reset; run bootcmd_usb; usb stop; run bootcmd1
bootcmd_usb=usb reset; run usb_scan; run make_usb_bootargs; ext2load usb $(usb_d              evice) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd;               bootm 0x40000 0x1100000
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) roo              t=LABEL=rootfs rootdelay=10
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no

Environment size: 2378/4091 bytes
Marvell>>

iomega ez
Re: Lenovo iomega EZ support
July 25, 2017 03:42AM
bodhi

could you suggest boot envs that check zImage then uImage so I can boot old debian7 with stock kernel.

I want to test network speed on debian7 with stock kernel. I am pretty sure that it was 2 times faster than debian8 with kernel 4.4.


thank you
Re: Lenovo iomega EZ support
July 25, 2017 03:58AM
iomega ez,

> I am pretty sure that it was 2 times faste
> r than debian8 with kernel 4.4.

I'd doubt that is the case. Similar network chip is used in all Kirkwood boxes and I did not see that much difference.

Did you test the pure network speed with iperf? or did you mean the NFS or Samba xfer speed are slower?

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Lenovo iomega EZ support
July 25, 2017 09:21AM
iomega ez,

How do you boot it? via usb?

Show me please ls -l /boot/

You can try load kernel to different memory places like:
I've had same issue with (stopping @ Starting kernel ...) with:
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;

Try instead:
ide read 0x40000 0x5000 0x2000; ide read 0x2100000 0xA000 0x4000; bootm 0x40000 0x2100000

You might not loaded complete kernel or initrd, or by writing to 0x900000 you've overwritten something important in the memory.

Meaning:
ide read addr blk# cnt
Meaning:
ide read #memory_address_to_copy_to #starting_disk_sector #number_of_sectors_to_load
Sector size = 512B

Can you please try to do the stability test from this thread and leave it to one hour?
What performance do you get? How do you test it? What protocol, give us some details.



Edited 7 time(s). Last edit at 07/25/2017 09:36AM by eine.
iomega ez
Re: Lenovo iomega EZ support
July 25, 2017 04:21PM
I use usb to boot debian.

I normally use hd-idle or hdparm to keep it cool. only my family use this device so normally it is on standby.


network test

samba read 75MB/s
samba write 42.9MB/s
ftp read 79.375MB/s
ftp write 46.521MB/s

I used to get about the same performance but now I am using jessie with 4.4 kernel. so I am trying to boot with old system to test network performance.

debian9 fail to boot

it just stops on starting kernel.

> 
> |  \/  | __ _ _ ____   _____| | |
> | |\/| |/ _` | '__\ \ / / _ \ | |
> | |  | | (_| | |   \ V /  __/ | |
> |_|  |_|\__,_|_|    \_/ \___|_|_|
> _   _     ____              _
> | | | |   | __ )  ___   ___ | |_
> | | | |___|  _ \ / _ \ / _ \| __|
> | |_| |___| |_) | (_) | (_) | |_
> \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** *
> * uboot_ver:0.0.8 **
> 
> ** MARVELL BOARD: DB-88F6282A-BP LE
> 
> U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell vers
> ion: 3.6.1 - EMC
> 
> U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A
> 0
> 
> Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @
> 600Mhz
> SysClock = 400Mhz , TClock = 200Mhz
> 
> DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD
> =6
> DRAM CS[0] base 0x00000000   size 128MB
> DRAM Total size 128MB  16bit width
> Addresses 8M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (8M - 7M): Done
> [1024kB@f8000000] Flash:  1 MB
> 
> Marvell Serial ATA Adapter
> Integrated Sata device found
> [0 0 0]: Enable DMA mode (6)
> Device 0 @ 0 0:
> Model: ST31500341AS                             Fi
> rm: CC71     Ser#:                           9VS3G
> 04B
> Type: Hard Disk
> Supports 48-bit addressing
> Capacity: 1430799.3 MB = 1397.2 GB (-1
> 364690128 x 512)
> 
> 
> CPU : Marvell Feroceon (Rev 1)
> 
> Streaming disabled
> Write allocate disabled
> 
> 
> USB 0: host mode
> PEX 0: interface detected no Link.
> PEX 1: interface detected no Link.
> Net:   egiga0 [PRIME]
> Hit any key to stop autoboot:  0
> 
> Reset IDE:
> Marvell Serial ATA Adapter
> Integrated Sata device found
> [0 0 0]: Enable DMA mode (6)
> Device 0 @ 0 0:
> Model: ST31500341AS                             Fi
> rm: CC71     Ser#:                           9VS3G
> 04B
> Type: Hard Disk
> Supports 48-bit addressing
> Capacity: 1430799.3 MB = 1397.2 GB (-1
> 364690128 x 512)
> 
> (Re)start USB...
> USB:   scanning bus for devices... 2 USB Device(s)
> found
> Waiting for storage device(s) to settle before sca
> nning...
> 1 Storage Device(s) found
> ....
> .
> ......
> ............
> .........................
> ..................................................
> .
> ..................................................
> ..............................              ......
> ................
> ..................................................
> ..............................              ......
> ..................................................
> ........................              .........
> 
> 3834687 bytes read
> ....
> .
> ......
> ............
> .........................
> ..................................................
> .
> ..................................................
> ..............................              ......
> ................
> ..................................................
> ..............................              ......
> ..................................................
> ........................              ............
> ................................
> ....
> ..................................................
> ..............................              ......
> ..................................................
> ........................              ............
> ..................................................
> ..................              ..................
> ...................................
> 
> 7245696 bytes read
> ## Booting image at 00040000 ...
> Image Name:   Linux-4.12.1-kirkwood-tld-1
> Created:      2017-07-25   7:14:43 UTC
> Image Type:   ARM Linux Kernel Image (uncompres
> sed)
> Data Size:    3834623 Bytes =  3.7 MB
> Load Address: 00008000
> Entry Point:  00008000
> Verifying Checksum ... OK
> OK
> ## Loading Ramdisk Image at 01100000 ...
> Image Name:   initramfs-4.12.1-kirkwood-tld-1
> Created:      2017-07-24   0:18:23 UTC
> Image Type:   ARM Linux RAMDisk Image (gzip com
> pressed)
> Data Size:    7245632 Bytes =  6.9 MB
> Load Address: 00000000
> Entry Point:  00000000
> Verifying Checksum ... OK
> 
> Starting kernel ...
> 
> 
>
Re: Lenovo iomega EZ support
July 25, 2017 05:44PM
iomega ez,
Please look @ this message: http://forum.doozan.com/read.php?2,35331,35423#msg-35423
And then you may try to modify:
Quote
iomega ez
## Loading Ramdisk Image at 01100000 ...
to point higher addres in the memory like I wrote in previous message.
Re: Lenovo iomega EZ support
July 25, 2017 06:07PM
iomega ez,

If it stops here without further output

> Starting kernel ...

Then you could add earlyprintk to see if you can get more output.

Power up, interrupt serial console and,

setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
boot

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
iomega ez
Re: Lenovo iomega EZ support
July 25, 2017 06:31PM
setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) earlyprintk=serial' 
setenv bootcmd_usb 'usb reset; run usb_scan; printenv bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x2100000 /boot/uInitrd; bootm 0x40000 0x2100000'

now it boots ok

Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST31500341AS                             Firm: CC71     Ser#:             9VS3G04B
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512)

(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) earlyprintk=serial
....
.
......
............
.........................
...................................................
......................................................................................................
.........................................................................................................................................................................

3834687 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.....................................................................................................................................................................................................................................................................................................

7245696 bytes read
## Booting image at 00040000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2017-07-25  10:18:46 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3834623 Bytes =  3.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes =  6.9 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    7.170713] console [ttyS0] enabled
[    7.177809] bootconsole [earlycon0] disabled
[    7.194746] loop: module loaded
[    7.198462] sata_mv f1080000.sata: slots 32 ports 2
[    7.206000] scsi host0: sata_mv
[    7.209559] scsi host1: sata_mv
[    7.212998] ata1: SATA max UDMA/133 irq 34
[    7.217118] ata2: SATA max UDMA/133 irq 34
[    7.222785] m25p80 spi0.0: found mx25l8005, expected mx25l8006e
[    7.228747] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    7.233646] 3 ofpart partitions found on MTD device spi0.0
[    7.239159] Creating 3 MTD partitions on "spi0.0":
[    7.243999] 0x000000000000-0x00000007e000 : "u-boot"
[    7.248987] mtd: partition "u-boot" doesn't end on an erase block -- force read-only
[    7.258056] 0x00000007e000-0x00000007f000 : "u-boot env2"
[    7.263531] mtd: partition "u-boot env2" doesn't start on an erase block boundary -- force read-only
[    7.273991] 0x00000007f000-0x000000080000 : "u-boot env"
[    7.279334] mtd: partition "u-boot env" doesn't start on an erase block boundary -- force read-only
[    7.290790] libphy: Fixed MDIO Bus: probed
[    7.295668] libphy: orion_mdio_bus: probed
[    7.304530] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    7.412409] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[    7.421249] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.427860] ehci-pci: EHCI PCI platform driver
[    7.432400] ehci-orion: EHCI orion driver
[    7.436613] orion-ehci f1050000.ehci: EHCI Host Controller
[    7.442240] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    7.450191] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    7.481404] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    7.487673] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    7.494536] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.501826] usb usb1: Product: EHCI Host Controller
[    7.506727] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd
[    7.513492] usb usb1: SerialNumber: f1050000.ehci
[    7.518888] hub 1-0:1.0: USB hub found
[    7.522743] hub 1-0:1.0: 1 port detected
[    7.527308] usbcore: registered new interface driver usb-storage
[    7.533741] mousedev: PS/2 mouse device common for all mice
[    7.539913] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    7.547032] i2c /dev entries driver
[    7.553118] hidraw: raw HID events driver (C) Jiri Kosina
[    7.558931] drop_monitor: Initializing network drop monitor service
[    7.565517] NET: Registered protocol family 17
[    7.570053] Key type dns_resolver registered
[    7.575127] registered taskstats version 1
[    7.579240] Loading compiled-in X.509 certificates
[    7.584139] zswap: loaded using pool lzo/zbud
[    7.597970] Key type big_key registered
[    7.610662] Key type encrypted registered
[    7.616079] rtc-mv f1010300.rtc: setting system clock to 2017-07-25 22:27:30 UTC (1501021650)
[    7.721429] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    7.761549] ata1.00: ATA-8: ST31500341AS, CC71, max UDMA/133
[    7.767239] ata1.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    7.831463] ata1.00: configured for UDMA/133
[    7.846289] scsi 0:0:0:0: Direct-Access     ATA      ST31500341AS     CC71 PQ: 0 ANSI: 5
[    7.855548] sd 0:0:0:0: [sda] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[    7.863927] sd 0:0:0:0: [sda] Write Protect is off
[    7.868891] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.881432] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    7.928736]  sda: sda1
[    7.932660] sd 0:0:0:0: [sda] Attached SCSI disk
[    8.076197] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[    8.082988] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    8.090191] usb 1-1: Product: USB Storage
[    8.094242] usb 1-1: Manufacturer: Generic
[    8.098470] usb 1-1: SerialNumber: 000000009451
[    8.104102] usb-storage 1-1:1.0: USB Mass Storage device detected
[    8.110510] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[    8.117466] scsi host2: usb-storage 1-1:1.0
[    8.193421] ata2: SATA link down (SStatus 0 SControl F300)
[    8.212617] Freeing unused kernel memory: 1024K
Loading, please wait...
starting version 232
[    8.657405] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
[    9.133292] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9451 PQ: 0 ANSI: 0
[    9.287121] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.08 GB/3.79 GiB)
[    9.295727] sd 2:0:0:0: [sdb] Write Protect is off
[    9.301600] sd 2:0:0:0: [sdb] No Caching mode page found
[    9.306949] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    9.323581]  sdb: sdb1
[    9.332874] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Warning: fsck not present, so skipping root file system
[   19.100395] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem
[   19.120610] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[ ok [   21.222201] input: gpio-keys as /devices/platform/gpio-keys/input/input0
                                                 done.
[....] Waiting for /dev to be fully populated...[   21.356712] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   21.492462] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   21.557733] orion_wdt: Initial timeout 21 sec
[   21.619944] adt7475 0-002e: ADT7473 device, revision 2
[   21.645575] marvell-cesa f1030000.crypto: CESA device successfully registered
[   21.673548] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   21.673989] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   21.785290] adt7475 0-002e: Bypassing attenuators on: in1
done.
[   22.593016] random: crng init done
[ ok ] Activating swap:.
[   22.887203] EXT4-fs (sdb1): re-mounted. Opts: (null)
[....] Will now check root file system:fsck from util-linux 2.29.2
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sdb1
e2fsck 1.43.4 (31-Jan-2017)
rootfs: clean, 14457/248992 files, 204221/994560 blocks
. ok
[   23.127791] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro
[ ok ] Will now activate lvm and md swap:done.
[info] Will now check all file systems.
fsck from util-linux 2.29.2
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location[ ok ritable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on   LPF/eth0/00:d0:b8:14:0b:8a
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
[   28.931850] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   33.499742] NET: Registered protocol family 10
[   33.506818] Segment Routing with IPv6
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
DHCPREQUEST of 192.168.2.101 on eth0 to 255.255.255.255 port 67
DHCPOFFER of 192.168.2.101 from 192.168.2.1
DHCPACK of 192.168.2.101 from 192.168.2.1
bound to 192.168.2.101 -- renewal in 41766 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1337 (syslogd)
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1336 (klogd)
. ok
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 9 debian ttyS0

debian login:

thank you
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: