Alternately boots lenny, then stock OS February 14, 2012 10:35PM |
Registered: 12 years ago Posts: 1 |
Saint Aardvark the Carpeted
Re: Alternately boots lenny, then stock OS March 22, 2012 02:14PM |
(Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 4 USB Device(s) found scanning bus for storage devices... error in inquiry
Re: Alternately boots lenny, then stock OS March 22, 2012 09:45PM |
Registered: 12 years ago Posts: 501 |
Saint Aardvark the Carpeted
Re: Alternately boots lenny, then stock OS March 23, 2012 09:56AM |
Re: Alternately boots lenny, then stock OS March 23, 2012 02:28PM |
Registered: 12 years ago Posts: 501 |
Re: Alternately boots lenny, then stock OS March 24, 2012 07:01AM |
Registered: 13 years ago Posts: 78 |
Re: Alternately boots lenny, then stock OS March 24, 2012 09:18AM |
Registered: 12 years ago Posts: 501 |
Saint Aardvark the Carpeted
Re: Alternately boots lenny, then stock OS March 24, 2012 12:39PM |
ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi ethaddr=00:25:31:00:74:7C arcNumber=2097 serverip=192.168.23.201 ipaddr=192.168.23.1 if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole bootcmd=usb start; usb stop; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; resetlaprjns: I have gone through the update process on Jeff's uBoot page, and it said I had the latest version already. It offered to reset the vars, so I did that; other than losing my netconsole settings and having to put them back in, it didn't make a difference. The build-your-own-uBoot instructions seemed relevant because I've seen other bug reports, similar to mine, that were resolved with a newer version of uBoot (like this one; there are others).