scales11
How to use usbboot? soft-bricked v4 pogoplug December 14, 2016 10:46PM |
Pogov4> printenv baudrate=115200 bootcmd=run boot_nand bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=b6:d0:5e:0f:a1:17 led_error=orange blinking led_exit=green off led_init=green blinking machid=f78 mainlineLinux=no mtddevname=uImage2 mtddevnum=2 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 rootdelay=10 rootfstype=ext2 set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts stderr=serial stdin=serial stdout=serial uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 Environment size: 1564/131068 bytes
Re: How to use usbboot? soft-bricked v4 pogoplug December 14, 2016 11:26PM |
Admin Registered: 13 years ago Posts: 18,564 |
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 15, 2016 06:41AM |
ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...\^C ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...| Sending boot image... 0 % [+++++++++++++++++xmodem: Bad message ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...| Sending boot image... 0 % [+++++++++++++++++xmodem: Bad message ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 1 % [......................................................................] 3 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 8 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 13 % [......................................................................] 15 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 20 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 25 % [......................................................................] 27 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 32 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 37 % [......................................................................] 39 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 44 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 49 % [......................................................................] 51 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 56 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 61 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 66 % [......................................................................] 68 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 73 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 78 % [......................................................................] 80 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 85 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 90 % [......................................................................] 92 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0
Re: How to use usbboot? soft-bricked v4 pogoplug December 15, 2016 06:38PM |
Admin Registered: 13 years ago Posts: 18,564 |
> ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B > 115200 /dev/ttyACM0 -b > uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p > Sending boot message. Please reboot the > target...\^C > ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B > 115200 /dev/ttyACM0 -b > uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p > Sending boot message. Please reboot the > target...| > Sending boot image... > 0 % [+++++++++++++++++xmodem: Bad message > ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B > 115200 /dev/ttyACM0 -b > uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p > Sending boot message. Please reboot the > target...| > Sending boot image... > 0 % [+++++++++++++++++xmodem: Bad message > ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B > 115200 /dev/ttyACM0 -b > uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p > Sending boot message. Please reboot the > target...\ > Sending boot image... > 0 % > [................................................. > .....................] > 1 % > [................................................. > .....................] > 3 % > [................................................. > .....................] > 5 % > [................................................. > .....................] > 6 % > [................................................. > .....................] > 8 % > [................................................. > .....................] > 10 % > [................................................. > .....................] > 11 % > [................................................. > .....................] > 13 % > [................................................. > .....................] > 15 % > [................................................. > .....................] > 17 % > [................................................. > .....................] > 18 % > [................................................. > .....................] > 20 % > [................................................. > .....................] > 22 % > [................................................. > .....................] > 23 % > [................................................. > .....................] > 25 % > [................................................. > .....................] > 27 % > [................................................. > .....................] > 29 % > [................................................. > .....................] > 30 % > [................................................. > .....................] > 32 % > [................................................. > .....................] > 34 % > [................................................. > .....................] > 35 % > [................................................. > .....................] > 37 % > [................................................. > .....................] > 39 % > [................................................. > .....................] > 41 % > [................................................. > .....................] > 42 % > [................................................. > .....................] > 44 % > [................................................. > .....................] > 46 % > [................................................. > .....................] > 47 % > [................................................. > .....................] > 49 % > [................................................. > .....................] > 51 % > [................................................. > .....................] > 53 % > [................................................. > .....................] > 54 % > [................................................. > .....................] > 56 % > [................................................. > .....................] > 58 % > [................................................. > .....................] > 59 % > [................................................. > .....................] > 61 % > [................................................. > .....................] > 63 % > [................................................. > .....................] > 64 % > [................................................. > .....................] > 66 % > [................................................. > .....................] > 68 % > [................................................. > .....................] > 70 % > [................................................. > .....................] > 71 % > [................................................. > .....................] > 73 % > [................................................. > .....................] > 75 % > [................................................. > .....................] > 76 % > [................................................. > .....................] > 78 % > [................................................. > .....................] > 80 % > [................................................. > .....................] > 82 % > [................................................. > .....................] > 83 % > [................................................. > .....................] > 85 % > [................................................. > .....................] > 87 % > [................................................. > .....................] > 88 % > [................................................. > .....................] > 90 % > [................................................. > .....................] > 92 % > [................................................. > .....................] > 94 % > [................................................. > .....................] > 95 % > [................................................. > .....................] > 97 % > [................................................. > .....................] > 99 % [....................................] > [Type Ctrl-\ + c to quit] > > > U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 > -0700) > Pogoplug V4 > > SoC: Kirkwood 88F6192_A1 > DRAM: 128 MiB > WARNING: Caches not enabled > NAND: 128 MiB > MMC: kwsdio: 0 > In: serial > Out: serial > Err: serial > Net: egiga0 > Hit any key to stop autoboot: 0 >
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 15, 2016 10:48PM |
ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...|^C ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...| Sending boot image... 0 % [+++++++++++++++++xmodem: Bad message ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 1 % [......................................................................] 3 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 8 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 13 % [......................................................................] 15 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 20 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 25 % [......................................................................] 27 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 32 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 37 % [......................................................................] 39 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 44 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 49 % [......................................................................] 51 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 56 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 61 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 66 % [......................................................................] 68 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 73 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 78 % [......................................................................] 80 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 85 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 90 % [......................................................................] 92 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 ## Error: "boot_nand" not defined Pogov4> setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset' Pogov4> saveenv Saving Environment to NAND... Erasing NAND... Erasing at 0xc0000 -- 100% complete. Writing to NAND... OK Pogov4> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found EHCI timed out on TD - token=0x90008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x1f8c80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x1f8c80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 01:16AM |
Admin Registered: 13 years ago Posts: 18,564 |
Pogov4> setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset'
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 03:07PM |
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 03:26PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 07:12PM |
Admin Registered: 13 years ago Posts: 18,564 |
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 07:36PM |
ubuntu@ubuntu:~/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyACM0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 1 % [......................................................................] 3 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 8 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 13 % [......................................................................] 15 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 20 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 25 % [......................................................................] 27 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 32 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 37 % [......................................................................] 39 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 44 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 49 % [......................................................................] 51 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 56 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 61 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 66 % [......................................................................] 68 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 73 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 78 % [......................................................................] 80 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 85 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 90 % [......................................................................] 92 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 3165162 bytes read in 386 ms (7.8 MiB/s) 7179935 bytes read in 509 ms (13.5 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-12-14 16:38:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3165098 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Pogoplug v4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 113632K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000014] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000495] Console: colour dummy device 80x30 [ 0.000544] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 0.090136] pid_max: default: 32768 minimum: 301 [ 0.090300] Security Framework initialized [ 0.090417] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090449] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091656] Initializing cgroup subsys io [ 0.091708] Initializing cgroup subsys devices [ 0.091745] Initializing cgroup subsys freezer [ 0.091793] Initializing cgroup subsys net_cls [ 0.091921] CPU: Testing write buffer coherency: ok [ 0.092628] Setting up static identity map for 0x8200 - 0x8258 [ 0.093089] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.098780] devtmpfs: initialized [ 0.105805] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.106512] prandom: seed boundary self test passed [ 0.112242] prandom: 100 self tests passed [ 0.112300] pinctrl core: initialized pinctrl subsystem [ 0.114422] NET: Registered protocol family 16 [ 0.115163] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.140164] cpuidle: using governor ladder [ 0.170164] cpuidle: using governor menu [ 0.170825] Feroceon L2: Enabling L2 [ 0.170890] Feroceon L2: Cache support initialised. [ 0.171456] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.179039] No ATAGs? [ 0.212288] vgaarb: loaded [ 0.212811] usbcore: registered new interface driver usbfs [ 0.212930] usbcore: registered new interface driver hub [ 0.213050] usbcore: registered new device driver usb [ 0.214687] clocksource: Switched to clocksource orion_clocksource [ 0.296308] NET: Registered protocol family 2 [ 0.297478] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.297522] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.297553] TCP: Hash tables configured (established 1024 bind 1024) [ 0.297664] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.297699] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.297978] NET: Registered protocol family 1 [ 0.298559] RPC: Registered named UNIX socket transport module. [ 0.298577] RPC: Registered udp transport module. [ 0.298588] RPC: Registered tcp transport module. [ 0.298599] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.298998] Unpacking initramfs... [ 1.249246] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 1.249460] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.251077] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.251181] audit: initializing netlink subsys (disabled) [ 1.251256] audit: type=2000 audit(1.240:1): initialized [ 1.251758] Initialise system trusted keyring [ 1.252343] zbud: loaded [ 1.252762] VFS: Disk quotas dquot_6.6.0 [ 1.252849] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.253629] NFS: Registering the id_resolver key type [ 1.253724] Key type id_resolver registered [ 1.253738] Key type id_legacy registered [ 1.253775] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.253796] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.254120] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.254961] Key type big_key registered [ 1.284091] Key type asymmetric registered [ 1.284125] Asymmetric key parser 'x509' registered [ 1.284271] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.284303] io scheduler noop registered [ 1.284325] io scheduler deadline registered [ 1.284416] io scheduler cfq registered (default) [ 1.286036] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 36 [ 1.286060] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 37 [ 1.286078] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 38 [ 1.286096] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 39 [ 1.286114] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 40 [ 1.286131] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 41 [ 1.286148] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 42 [ 1.286166] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 43 [ 1.286184] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 44 [ 1.286201] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 45 [ 1.286219] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 46 [ 1.286236] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47 [ 1.286253] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 48 [ 1.286271] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49 [ 1.286759] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 1.287745] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated [ 1.288349] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated [ 1.289568] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 1.289597] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.289617] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 1.289637] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.290224] PCI: bus0: Fast back to back transfers disabled [ 1.290263] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.304799] PCI: bus1: Fast back to back transfers disabled [ 1.305056] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 1.305087] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit] [ 1.305121] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit] [ 1.305152] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit] [ 1.305180] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.305203] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.305343] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 1.305499] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 1.305937] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.345734] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.346068] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.385697] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.386401] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.388539] console [ttyS0] disabled [ 1.388631] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 2.184362] console [ttyS0] enabled [ 2.189787] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 2.196172] nand: Hynix H27U1G8F2BTR-BC [ 2.199998] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.207574] Scanning device for bad blocks [ 2.296184] 5 cmdlinepart partitions found on MTD device orion_nand [ 2.302431] Creating 5 MTD partitions on "orion_nand": [ 2.307588] 0x000000000000-0x000000200000 : "u-boot" [ 2.314437] 0x000000200000-0x000000500000 : "uImage" [ 2.321242] 0x000000500000-0x000000800000 : "uImage2" [ 2.328091] 0x000000800000-0x000001000000 : "failsafe" [ 2.335075] 0x000001000000-0x000008000000 : "root" [ 2.343509] libphy: Fixed MDIO Bus: probed [ 2.348189] libphy: orion_mdio_bus: probed [ 2.359361] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 3.442864] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address b6:d0:5e:0f:a1:17 [ 3.451800] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.458380] ehci-pci: EHCI PCI platform driver [ 3.462918] ehci-orion: EHCI orion driver [ 3.467203] orion-ehci f1050000.ehci: EHCI Host Controller [ 3.472713] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 3.480614] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 3.504734] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 3.511037] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.517842] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.525062] usb usb1: Product: EHCI Host Controller [ 3.529927] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 3.536543] usb usb1: SerialNumber: f1050000.ehci [ 3.542323] hub 1-0:1.0: USB hub found [ 3.546185] hub 1-0:1.0: 1 port detected [ 3.551012] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 3.556335] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 3.565137] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00000010 [ 3.573849] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.580657] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.587874] usb usb2: Product: xHCI Host Controller [ 3.592740] usb usb2: Manufacturer: Linux 4.4.0-kirkwood-tld-1 xhci-hcd [ 3.599356] usb usb2: SerialNumber: 0000:01:00.0 [ 3.605050] hub 2-0:1.0: USB hub found [ 3.608839] hub 2-0:1.0: 2 ports detected [ 3.613582] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 3.618885] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 3.626414] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.634666] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.641469] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.648819] usb usb3: Product: xHCI Host Controller [ 3.653687] usb usb3: Manufacturer: Linux 4.4.0-kirkwood-tld-1 xhci-hcd [ 3.660310] usb usb3: SerialNumber: 0000:01:00.0 [ 3.665941] hub 3-0:1.0: USB hub found [ 3.669729] hub 3-0:1.0: 2 ports detected [ 3.675251] mousedev: PS/2 mouse device common for all mice [ 3.864733] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 4.015866] usb 1-1: New USB device found, idVendor=0781, idProduct=5576 [ 4.022564] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.029721] usb 1-1: Product: Cruzer Facet [ 4.033803] usb 1-1: Manufacturer: SanDisk [ 4.037915] usb 1-1: SerialNumber: 4C532000060525114554 [ 4.684727] rtc-mv f1010300.rtc: internal RTC not ticking [ 4.690414] i2c /dev entries driver [ 4.695814] hidraw: raw HID events driver (C) Jiri Kosina [ 4.701784] drop_monitor: Initializing network drop monitor service [ 4.708462] NET: Registered protocol family 17 [ 4.713287] Key type dns_resolver registered [ 4.718830] registered taskstats version 1 [ 4.722983] Loading compiled-in X.509 certificates [ 4.727895] zswap: loaded using pool lzo/zbud [ 4.745032] Key type encrypted registered [ 4.749946] hctosys: unable to open rtc device (rtc0) [ 4.758482] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 4.866386] systemd-udevd[84]: starting version 215 [ 4.874126] random: systemd-udevd urandom read with 7 bits of entropy available [ 5.154630] SCSI subsystem initialized [ 5.167103] mvsdio f1090000.mvsdio: Got CD GPIO [ 5.200332] usb-storage 1-1:1.0: USB Mass Storage device detected [ 5.251181] sata_mv f1080000.sata: slots 32 ports 1 [ 5.278747] scsi host0: usb-storage 1-1:1.0 [ 5.292074] usbcore: registered new interface driver usb-storage [ 5.312622] scsi host1: sata_mv [ 5.325343] ata1: SATA max UDMA/133 irq 32 [ 5.341525] usbcore: registered new interface driver uas [ 5.674749] ata1: SATA link down (SStatus 0 SControl F300) [ 6.276137] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Facet 1.26 PQ: 0 ANSI: 5 [ 6.296827] sd 0:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [ 6.306436] sd 0:0:0:0: [sda] Write Protect is off [ 6.312039] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 6.329122] sda: sda1 [ 6.336038] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 6.347742] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Checking root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 20.939979] EXT2-fs (sda1): error: couldn't mount because of unsupported optional features (4) mount: mounting /dev/sda1 on /root failed: Invalid argument done. Target filesystem doesn't have requested /sbin/init. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory done. No init found. Try passing init= bootarg. modprobe: module i8042 not found in modules.dep [ 21.128646] uhci_hcd: USB Universal Host Controller Interface driver [ 21.147234] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 21.166974] usbcore: registered new interface driver usbhid [ 21.172536] usbhid: USB HID core driver BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs)
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 07:40PM |
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 08:26PM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv set_bootargs_usb 'setenv bootargs console=$console root=LABEL=rootfs rootdelay=$rootdelay $mtdparts' boot
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 09:20PM |
Re: How to use usbboot? soft-bricked v4 pogoplug December 16, 2016 10:50PM |
Admin Registered: 13 years ago Posts: 18,564 |
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 17, 2016 01:14PM |
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00200000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00300000 00020000 "uImage2" mtd3: 00800000 00020000 "failsafe" mtd4: 07000000 00020000 "root"
Re: How to use usbboot? soft-bricked v4 pogoplug December 17, 2016 02:58PM |
Admin Registered: 13 years ago Posts: 18,564 |
How to boot Arch Linux ARM with bodhi's u-boot December 17, 2016 03:03PM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv dtb_file_alt '/boot/dtbs/kirkwood-pogoplug_v4.dtb' setenv load_dtb 'echo loading DTB file ... ; if load $bootdev $device $load_dtb_addr $dtb_file; then echo $dtb_file; else if load $bootdev $device $load_dtb_addr $dtb_file_alt; then echo $dtb_file_alt; else echo *** DTB file not found; fi; fi' boot
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 18, 2016 08:14AM |
root@debian:/media/usbstick# tools/nandwrite -s 786432 /dev/mtd0 uboot.2016.05-tld-1.environment.bodhi/uboot.2016.05-tld-1.environment.img Writing data to block 6 at offset 0xc0000 root@debian:/media/usbstick# fw_setenv arcNumber 3960 Warning: Bad CRC, using default environment root@debian:/media/usbstick#
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 18, 2016 10:06AM |
Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 1 % [......................................................................] 3 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 8 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 13 % [......................................................................] 15 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 20 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 25 % [......................................................................] 27 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 32 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 37 % [......................................................................] 39 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 44 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 49 % [......................................................................] 51 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 56 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 61 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 66 % [......................................................................] 68 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 73 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 78 % [......................................................................] 80 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 85 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 90 % [......................................................................] 92 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=B6:D0:5E:0F:A1:17 machid=f78 stderr=serial stdin=serial stdout=serial Environment size: 352/131068 bytes Pogov4>
Re: How to use usbboot? soft-bricked v4 pogoplug December 18, 2016 03:30PM |
Admin Registered: 13 years ago Posts: 18,564 |
root@debian:/media/usbstick# tools/nandwrite -s 786432 /dev/mtd0 uboot.2016.05-tld-1.environment.bodhi/uboot.2016.05-tld-1.environment.img Writing data to block 6 at offset 0xc0000
root@debian:/media/usbstick# fw_setenv arcNumber 3960 Warning: Bad CRC, using default environment
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=B6:D0:5E:0F:A1:17 machid=f78 stderr=serial stdin=serial stdout=serial Environment size: 352/131068 bytes Pogov4>
Quote
Adjust the other specific envs and then boot the rootfs:
setenv devices 'usb mmc ide' setenv ethaddr xx:xx:xx:xx:xx:xx setenv dtb_file '/boot/dts/kirkwood-pogoplug_v4.dtb'
boot
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 24, 2016 08:01AM |
87 % [......................................................................] 88 % [......................................................................] 90 % [......................................................................] 92 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> usb start starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Pogov4> ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr ** File not found /boot/uboot.2016.05-tld-1.environment.scr ** Pogov4> ls usb 0:1 0x800000 ** Can not find directory. ** Pogov4> ls usb 0:1 <DIR> 4096 . <DIR> 4096 .. <DIR> 16384 lost+found <DIR> 4096 proc <DIR> 4096 sbin <DIR> 4096 dev <DIR> 4096 root <DIR> 4096 usr <DIR> 4096 opt <DIR> 4096 boot <DIR> 4096 bin <DIR> 4096 etc <DIR> 4096 tmp <DIR> 4096 mnt <DIR> 4096 var <DIR> 4096 home <DIR> 4096 media <DIR> 4096 sys <DIR> 4096 run <DIR> 4096 lib <DIR> 4096 srv Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=B6:D0:5E:0F:A1:17 machid=f78 stderr=serial stdin=serial stdout=serial
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 24, 2016 12:40PM |
Re: How to use usbboot? soft-bricked v4 pogoplug December 24, 2016 03:54PM |
Admin Registered: 13 years ago Posts: 18,564 |
Pogov4> ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr ** File not found /boot/uboot.2016.05-tld-1.environment.scr **
scalees11
Re: How to use usbboot? soft-bricked v4 pogoplug December 25, 2016 08:30AM |
Re: How to use usbboot? soft-bricked v4 pogoplug December 25, 2016 04:15PM |
Admin Registered: 13 years ago Posts: 18,564 |
printenv usb start ext2ls usb 0:1 /boot
Scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 26, 2016 08:30PM |
92 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=B6:D0:5E:0F:A1:17 machid=f78 stderr=serial stdin=serial stdout=serial Environment size: 352/131068 bytes Pogov4> usb start starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Pogov4> ext2ls usb 0:1 /boot <DIR> 4096 . <DIR> 4096 .. 140949 config-4.4.0-kirkwood-tld-1 3154832 vmlinuz-4.4.0-kirkwood-tld-1 7179935 uInitrd 7179871 initrd.img-4.4.0-kirkwood-tld-1 2240040 System.map-4.4.0-kirkwood-tld-1 <DIR> 4096 dts 3165162 uImage 7511582 linux-headers-4.4.0-kirkwood-tld-1_1.0_armel.deb 3154832 zImage-4.4.0-kirkwood-tld-1 3165098 zImage.fdt 3154896 uImage.org 2776 uEnv.txt 3232 uboot.2016.05-tld-1.environment.scr Pogov4>
Re: How to use usbboot? soft-bricked v4 pogoplug December 27, 2016 01:52AM |
Admin Registered: 13 years ago Posts: 18,564 |
ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 27, 2016 07:32AM |
~$ sudo fsck /dev/sdc fsck from util-linux 2.27.1 e2fsck 1.42.13 (17-May-2015) ext2fs_open2: Bad magic number in super-block fsck.ext2: Superblock invalid, trying backup blocks... fsck.ext2: Bad magic number in super-block while trying to open /dev/sdc The superblock could not be read or does not describe a valid ext2/ext3/ext4 filesystem. If the device is valid and it really contains an ext2/ext3/ext4 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> or e2fsck -b 32768 <device>
scales11
Re: How to use usbboot? soft-bricked v4 pogoplug December 27, 2016 01:44PM |
Re: How to use usbboot? soft-bricked v4 pogoplug December 27, 2016 03:04PM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
5. Done. Take this USB rootfs to your plug and cold start. After booted into Debian, see Note1 and Note2 below. It is very important that you do Note1 steps to secure your box.
~$ sudo fsck /dev/sdc1