[SOLVED] Help unbricking Pogo E02 February 17, 2017 06:29AM |
Registered: 10 years ago Posts: 38 |
PogoE02> printenv arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; run bootcmd_pogo; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:00:5d:10 if_netconsole=ping $serverip ipaddr=192.168.1.10 led_error=orange blinking led_exit=green off led_init=green blinking machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot=run if_netconsole start_netconsole preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.1.100 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext3 Environment size: 2459/131068 bytesIs possible to install debian 8 from this startpoint or do I miss something? thank you in advance. Marco
Re: Help unbricking Pogo E02 February 17, 2017 03:52PM |
Admin Registered: 13 years ago Posts: 18,554 |
Re: Help unbricking Pogo E02 February 18, 2017 04:50AM |
Registered: 10 years ago Posts: 38 |
U-Boot 2015.10-tld-1 (Nov 06 2015 - 15:46:25 -0800) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB (ECC not enabled) WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 No link on egiga0 ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Unknown command 'mmc' - try 'help' ** Bad device mmc 0 ** ** Bad device mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Unknown command 'ide' - try 'help' ** Bad device ide 0 ** ** Bad device ide 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! UBI: attaching mtd1 to ubi0 UBI: scanning is finished UBI init error 22 resetting ... U-Boot 2015.10-tld-1 (Nov 06 2015 - 15:46:25 -0800) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB (ECC not enabled) WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 No link on egiga0 ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 PogoE02>And this is printenv
PogoE02> printenv arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; run bootcmd_pogo; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:00:5d:10 if_netconsole=ping $serverip ipaddr=192.168.1.10 led_error=orange blinking led_exit=green off led_init=green blinking machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot=run if_netconsole start_netconsole preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.1.100 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext3 Environment size: 2459/131068 bytes PogoE02>I used this tutorial to recover uboot after a bad flash. I installed this uboot.2015.10-tld-1.pogo_e02.bodhi.tar
Re: Help unbricking Pogo E02 February 18, 2017 06:11AM |
Admin Registered: 13 years ago Posts: 18,554 |
Quote
Updated 20 Feb 2016:
This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1.
cp -a uboot.2016.05-tld-1.environment.scr /media/sdb1/boot/ sync
usb start ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr source 0x800000
boot
Re: Help unbricking Pogo E02 February 19, 2017 05:33AM |
Registered: 10 years ago Posts: 38 |
Quote
3. And install it with dpkg. If you encounter error with flash-kernel when running dpkg, then remove flash-kernel first to avoid potential problem (It is much better to generate uImage and uInitrd manually anyway):
(initramfs) ls bin dev init proc run scripts tmp conf etc lib root sbin sys var
Re: Help unbricking Pogo E02 February 19, 2017 03:57PM |
Admin Registered: 13 years ago Posts: 18,554 |
Re: Help unbricking Pogo E02 February 21, 2017 07:23AM |
Registered: 10 years ago Posts: 38 |
root@debian:~# uname -a Linux debian 4.4.0-kirkwood-tld-1 #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 armv5tel GNU/Linux root@debian:~# cat /etc/debian_version 8.3When I booted after this step
usb start ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr source 0x800000I encountered a kernel panic but now I think everything should be right.
Re: Help unbricking Pogo E02 February 22, 2017 12:49AM |
Admin Registered: 13 years ago Posts: 18,554 |
usb start ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr source 0x800000
root@debian:~# uname -a Linux debian 4.4.0-kirkwood-tld-1 #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 armv5tel GNU/Linux
usb start ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr source 0x800000 saveenvand
boot
Re: Help unbricking Pogo E02 February 22, 2017 06:52AM |
Registered: 10 years ago Posts: 38 |
Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f440000, end 0fb18e5f ... OK Loading Device Tree to 0f43a000, end 0f43f8cd ... OK Using machid 0x831 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: CloudEngines Pogoplug E02 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 250592K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 11552K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008270] Console: colour dummy device 80x30 [ 0.012836] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.100932] pid_max: default: 32768 minimum: 301 [ 0.105753] Security Framework initialized [ 0.110070] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.116816] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.124809] Initializing cgroup subsys io [ 0.128993] Initializing cgroup subsys devices [ 0.133564] Initializing cgroup subsys freezer [ 0.138181] Initializing cgroup subsys net_cls [ 0.142808] CPU: Testing write buffer coherency: ok [ 0.148317] Setting up static identity map for 0x8200 - 0x8258 [ 0.154554] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.163626] devtmpfs: initialized [ 0.171697] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.182176] prandom: seed boundary self test passed [ 0.190992] prandom: 100 self tests passed [ 0.195224] pinctrl core: initialized pinctrl subsystem [ 0.202006] NET: Registered protocol family 16 [ 0.207002] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.238053] cpuidle: using governor ladder [ 0.268049] cpuidle: using governor menu [ 0.272484] Feroceon L2: Enabling L2 [ 0.276195] Feroceon L2: Cache support initialised. [ 0.281602] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.297079] No ATAGs? [ 0.329557] vgaarb: loaded [ 0.332990] usbcore: registered new interface driver usbfs [ 0.338717] usbcore: registered new interface driver hub [ 0.344210] usbcore: registered new device driver usb [ 0.350492] clocksource: Switched to clocksource orion_clocksource [ 0.412563] NET: Registered protocol family 2 [ 0.417827] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.425067] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.431585] TCP: Hash tables configured (established 2048 bind 2048) [ 0.438115] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.444097] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.450698] NET: Registered protocol family 1 [ 0.455517] RPC: Registered named UNIX socket transport module. [ 0.461604] RPC: Registered udp transport module. [ 0.466417] RPC: Registered tcp transport module. [ 0.471243] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.478178] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.485904] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.492248] audit: initializing netlink subsys (disabled) [ 0.497794] audit: type=2000 audit(0.480:1): initialized [ 0.503633] Initialise system trusted keyring [ 0.508435] zbud: loaded [ 0.511389] VFS: Disk quotas dquot_6.6.0 [ 0.515469] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.523151] NFS: Registering the id_resolver key type [ 0.528341] Key type id_resolver registered [ 0.532680] Key type id_legacy registered [ 0.536822] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.543671] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.550357] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.558065] Key type big_key registered [ 0.573435] Key type asymmetric registered [ 0.577650] Asymmetric key parser 'x509' registered [ 0.582815] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.590340] io scheduler noop registered [ 0.594556] io scheduler deadline registered [ 0.598994] io scheduler cfq registered (default) [ 0.605202] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.613405] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 0.620839] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 0.628362] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.671183] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.678837] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.721182] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.729095] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.737014] console [ttyS0] disabled [ 0.740811] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 0.749934] console [ttyS0] enabled [ 0.749934] console [ttyS0] enabled [ 0.757071] bootconsole [earlycon0] disabled [ 0.757071] bootconsole [earlycon0] disabled [ 0.767152] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 0.773576] nand: Hynix NAND 128MiB 3,3V 8-bit [ 0.778039] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.785670] Scanning device for bad blocks [ 0.901335] libphy: Fixed MDIO Bus: probed [ 0.905786] libphy: orion_mdio_bus: probed [ 0.910678] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 1.991142] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:00:5d:10 [ 2.000022] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.006639] ehci-pci: EHCI PCI platform driver [ 2.011201] ehci-orion: EHCI orion driver [ 2.015404] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.020973] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.028825] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.050582] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.056848] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.063703] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.070982] usb usb1: Product: EHCI Host Controller [ 2.075881] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.082544] usb usb1: SerialNumber: f1050000.ehci [ 2.088005] hub 1-0:1.0: USB hub found [ 2.091871] hub 1-0:1.0: 1 port detected [ 2.096789] mousedev: PS/2 mouse device common for all mice [ 2.410526] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.562083] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.568832] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.576034] usb 1-1: Product: USB2.0 Hub [ 2.580944] hub 1-1:1.0: USB hub found [ 2.585083] hub 1-1:1.0: 4 ports detected [ 2.870520] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 2.981457] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5571 [ 2.988381] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.995763] usb 1-1.3: Product: Cruzer Fit [ 2.999878] usb 1-1.3: Manufacturer: SanDisk [ 3.004188] usb 1-1.3: SerialNumber: 4C530201270404115231 [ 3.110523] rtc-mv f1010300.rtc: internal RTC not ticking [ 3.116155] i2c /dev entries driver [ 3.120986] hidraw: raw HID events driver (C) Jiri Kosina [ 3.126826] drop_monitor: Initializing network drop monitor service [ 3.133412] NET: Registered protocol family 17 [ 3.138147] Key type dns_resolver registered [ 3.143346] registered taskstats version 1 [ 3.147507] Loading compiled-in X.509 certificates [ 3.152417] zswap: loaded using pool lzo/zbud [ 3.157898] Key type encrypted registered [ 3.162498] hctosys: unable to open rtc device (rtc0) [ 3.169021] Waiting 10 sec before mounting root device... [ 13.180752] VFS: Cannot open root device "sda1" or unknown-block(0,0): error -6 [ 13.188098] Please append a correct "root=" boot option; here are the available partitions: [ 13.196547] 1f00 131072 mtdblock0 (driver?) [ 13.201680] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 13.209980] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-kirkwood-tld-1 #1 [ 13.216969] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 13.223296] [<c0016784>] (unwind_backtrace) from [<c00129f8>] (show_stack+0x10/0x14) [ 13.231080] [<c00129f8>] (show_stack) from [<c00c2200>] (panic+0x80/0x214) [ 13.237995] [<c00c2200>] (panic) from [<c07d9280>] (mount_block_root+0x204/0x24c) [ 13.245517] [<c07d9280>] (mount_block_root) from [<c07d93b4>] (mount_root+0xec/0x118) [ 13.253391] [<c07d93b4>] (mount_root) from [<c07d9504>] (prepare_namespace+0x124/0x184) [ 13.261431] [<c07d9504>] (prepare_namespace) from [<c07d8e9c>] (kernel_init_freeable+0x208/0x258) [ 13.270349] [<c07d8e9c>] (kernel_init_freeable) from [<c05b16b4>] (kernel_init+0x8/0xe4) [ 13.278481] [<c05b16b4>] (kernel_init) from [<c000f090>] (ret_from_fork+0x14/0x24) [ 13.286092] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Re: Help unbricking Pogo E02 February 22, 2017 05:24PM |
Admin Registered: 13 years ago Posts: 18,554 |
usb start ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr source 0x800000 printenvand then
boot
Quote
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
Re: Help unbricking Pogo E02 February 23, 2017 06:05PM |
Registered: 10 years ago Posts: 38 |
Re: Help unbricking Pogo E02 February 23, 2017 09:57PM |
Admin Registered: 13 years ago Posts: 18,554 |
Re: Help unbricking Pogo E02 February 24, 2017 09:15AM |
Registered: 10 years ago Posts: 38 |