Dockstar - no network April 18, 2017 07:16PM |
Registered: 6 years ago Posts: 57 |
U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 u-boot>>
ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; na nd read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 / rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd ; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0 :rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && u bifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if t est $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_ scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; se tenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_ rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext 2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; el se bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=xx:xx:xx:xx:xx:xx arcNumber=2097
Re: Dockstar - no network April 18, 2017 09:17PM |
Registered: 10 years ago Posts: 1,303 |
Re: Dockstar - no network April 18, 2017 10:23PM |
Registered: 6 years ago Posts: 57 |
Re: Dockstar - no network April 19, 2017 12:55AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 19, 2017 08:23AM |
Registered: 6 years ago Posts: 57 |
Re: Dockstar - no network April 19, 2017 08:31PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 19, 2017 08:42PM |
Registered: 6 years ago Posts: 57 |
U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 3 ^H^H^H 2 ^H^H^H 1 ^H^H^H 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1752 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1731 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ^H^H. ^H^H. ^H^H. ^H^H. ^H^H. ^H^H. ^H^H. read_nand_cached: error reading nand off 0x122e400 size 8192 bytes ^H^H. ^H^H. read_nand_cached: error reading nand off 0x1afc200 size 8192 bytes ^H^H done.^M read_nand_cached: error reading nand off 0x122f000 size 8192 bytes off = 0x122e9f0 magic 0x1985 type 0xe002 node.totlen = 2444 read_nand_cached: error reading nand off 0x1afc000 size 8192 bytes off = 0x1afbf24 magic 0x1985 type 0xe002 node.totlen = 446 ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
Re: Dockstar - no network April 19, 2017 08:50PM |
Admin Registered: 13 years ago Posts: 18,495 |
> U-Boot 2011.12 (Feb 12 2012 - 21:33:07) > Seagate FreeAgent DockStar > > SoC: Kirkwood 88F6281_A0 > DRAM: 128 MiB > WARNING: Caches not enabled > NAND: 256 MiB > In: serial > Out: serial > Err: serial > Net: egiga0 > 88E1116 Initialized on egiga0 > Hit any key to stop autoboot: 3 ^H^H^H 2 ^H^H^H 1 > ^H^H^H 0 > (Re)start USB... > USB: Register 10011 NbrPorts 1 > USB EHCI 1.00 > scanning bus for devices... 2 USB Device(s) found > scanning bus for storage devices... 0 Stora > ge Device(s) found > ** Block device usb 0 not supported > > ** Invalid boot device ** > Creating 1 MTD partitions on "nand0": > 0x000002500000-0x000010000000 : "mtd=3" > UBI: attaching mtd1 to ubi0 > UBI: physical eraseblock size: 131072 bytes (128 > KiB) > UBI: logical eraseblock size: 129024 bytes > UBI: smallest flash I/O unit: 2048 > UBI: sub-page size: 512 > UBI: VID header offset: 512 (aligned 512) > UBI: data offset: 2048 > UBI: attached mtd1 to ubi0 > UBI: MTD device name: "mtd=3" > UBI: MTD device size: 219 MiB > UBI: number of good PEBs: 1752 > UBI: number of bad PEBs: 0 > UBI: max. allowed volumes: 128 > UBI: wear-leveling threshold: 4096 > UBI: number of internal volumes: 1 > UBI: number of user volumes: 0 > UBI: available PEBs: 1731 > UBI: total number of reserved PEBs: 21 > UBI: number of PEBs reserved for bad PEB handling: > 17 > UBI: max/mean erase counter: 1/1 > UBIFS error (pid 0): ubifs_get_sb: cannot open "ub > i:rootfs", error -19 > Error reading superblock on volume 'ubi:rootfs'! > ** Block device usb 0 not supported > ** Block device usb 1 not supported > ** Block device usb 2 not supported > ** Block device usb 3 not supported > ** Block device usb 0 not supported > ** Block device usb 0 not supported > Wrong Image Format for bootm command > ERROR: can't get kernel image! > stopping USB.. > ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x8 > 00000 > Scanning JFFS2 FS: ^H^H. ^H^H. ^H^H. ^H^H. ^ > H^H. ^H^H. ^H^H. read_nand_cached: error readin > g nand off 0x122e400 size 8192 bytes > ^H^H. ^H^H. read_nand_cached: error reading nand > off 0x1afc200 size 8192 bytes > ^H^H done.^M > read_nand_cached: error reading nand off 0x122f000 > size 8192 bytes > off = 0x122e9f0 magic 0x1985 type 0xe002 node.totl > en = 2444 > read_nand_cached: error reading nand off 0x1afc000 > size 8192 bytes > off = 0x1afbf24 magic 0x1985 type 0xe002 node.totl > en = 446 > ### JFFS2 load complete: 524288 bytes loaded to 0x > 800000 > ## Starting application at 0x00800200 ... >>
Re: Dockstar - no network April 19, 2017 09:29PM |
Registered: 6 years ago Posts: 57 |
U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1752 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1731 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 (usbda1) 3166793 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 7179935 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3166729 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Seagate GoFlex Net [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000335] Console: colour dummy device 80x30 [ 0.000366] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090106] pid_max: default: 32768 minimum: 301 [ 0.090216] Security Framework initialized [ 0.090295] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090317] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091119] Initializing cgroup subsys io [ 0.091152] Initializing cgroup subsys devices [ 0.091178] Initializing cgroup subsys freezer [ 0.091213] Initializing cgroup subsys net_cls [ 0.091298] CPU: Testing write buffer coherency: ok [ 0.091774] Setting up static identity map for 0x8200 - 0x8258 [ 0.092088] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.095880] devtmpfs: initialized [ 0.101088] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.101562] prandom: seed boundary self test passed [ 0.105321] prandom: 100 self tests passed [ 0.105348] pinctrl core: initialized pinctrl subsystem [ 0.106754] NET: Registered protocol family 16 [ 0.107229] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130108] cpuidle: using governor ladder [ 0.160107] cpuidle: using governor menu [ 0.160551] Feroceon L2: Enabling L2 [ 0.160598] Feroceon L2: Cache support initialised. [ 0.160991] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.166157] No ATAGs? [ 0.201619] vgaarb: loaded [ 0.202003] usbcore: registered new interface driver usbfs [ 0.202086] usbcore: registered new interface driver hub [ 0.202150] usbcore: registered new device driver usb [ 0.203273] clocksource: Switched to clocksource orion_clocksource [ 0.259081] NET: Registered protocol family 2 [ 0.259906] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.259933] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.259954] TCP: Hash tables configured (established 1024 bind 1024) [ 0.260023] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260047] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260247] NET: Registered protocol family 1 [ 0.260660] RPC: Registered named UNIX socket transport module. [ 0.260673] RPC: Registered udp transport module. [ 0.260680] RPC: Registered tcp transport module. [ 0.260688] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.260974] Unpacking initramfs... [ 0.908138] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 0.908286] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.909416] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.909492] audit: initializing netlink subsys (disabled) [ 0.909550] audit: type=2000 audit(0.900:1): initialized [ 0.909913] Initialise system trusted keyring [ 0.910321] zbud: loaded [ 0.910619] VFS: Disk quotas dquot_6.6.0 [ 0.910682] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.911233] NFS: Registering the id_resolver key type [ 0.911290] Key type id_resolver registered [ 0.911299] Key type id_legacy registered [ 0.911326] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.911340] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.911567] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.912095] Key type big_key registered [ 0.932482] Key type asymmetric registered [ 0.932506] Asymmetric key parser 'x509' registered [ 0.932608] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.932630] io scheduler noop registered [ 0.932645] io scheduler deadline registered [ 0.932709] io scheduler cfq registered (default) [ 0.934204] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.934899] irq: Cannot allocate irq_descs @ IRQ33, assuming pre-allocated [ 0.935327] irq: Cannot allocate irq_descs @ IRQ65, assuming pre-allocated [ 0.935875] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.973975] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.974215] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.013956] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.014466] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.015900] console [ttyS0] disabled [ 1.015964] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 1.616571] console [ttyS0] enabled [ 1.621528] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 1.627947] nand: Micron MT29F2G08AAD [ 1.631626] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.639257] Scanning device for bad blocks [ 1.862255] 4 cmdlinepart partitions found on MTD device orion_nand [ 1.868566] Creating 4 MTD partitions on "orion_nand": [ 1.873756] 0x000000000000-0x000000100000 : "u-boot" [ 1.880035] 0x000000100000-0x000000500000 : "uImage" [ 1.886327] 0x000000500000-0x000002500000 : "rootfs" [ 1.892577] 0x000002500000-0x000010000000 : "data" [ 1.900094] libphy: Fixed MDIO Bus: probed [ 1.904613] libphy: orion_mdio_bus: probed [ 1.913803] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.993990] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address xx:xx:xx:xx:xx:xx [ 3.002885] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.009508] ehci-pci: EHCI PCI platform driver [ 3.014067] ehci-orion: EHCI orion driver [ 3.018281] orion-ehci f1050000.ehci: EHCI Host Controller [ 3.023848] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 3.031732] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 3.053307] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 3.059571] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.066422] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.073699] usb usb1: Product: EHCI Host Controller [ 3.078598] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 3.085261] usb usb1: SerialNumber: f1050000.ehci [ 3.090759] hub 1-0:1.0: USB hub found [ 3.094626] hub 1-0:1.0: 1 port detected [ 3.099586] mousedev: PS/2 mouse device common for all mice [ 3.413307] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 3.564987] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 3.571736] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.578942] usb 1-1: Product: USB2.0 Hub [ 3.583829] hub 1-1:1.0: USB hub found [ 3.587988] hub 1-1:1.0: 4 ports detected [ 3.873300] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 3.987359] usb 1-1.2: New USB device found, idVendor=0930, idProduct=6545 [ 3.994298] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.001667] usb 1-1.2: Product: DataTraveler G3 [ 4.006243] usb 1-1.2: Manufacturer: Kingston [ 4.010617] usb 1-1.2: SerialNumber: 001372970D64EB60A51101AE [ 4.113306] rtc-mv f1010300.rtc: internal RTC not ticking [ 4.118944] i2c /dev entries driver [ 4.125083] hidraw: raw HID events driver (C) Jiri Kosina [ 4.130902] drop_monitor: Initializing network drop monitor service [ 4.137491] NET: Registered protocol family 17 [ 4.142227] Key type dns_resolver registered [ 4.147445] registered taskstats version 1 [ 4.151611] Loading compiled-in X.509 certificates [ 4.156520] zswap: loaded using pool lzo/zbud [ 4.169854] Key type encrypted registered [ 4.174522] hctosys: unable to open rtc device (rtc0) [ 4.181920] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 4.258777] systemd-udevd[83]: starting version 215 [ 4.275470] random: systemd-udevd urandom read with 7 bits of entropy available [ 4.441813] SCSI subsystem initialized [ 4.509128] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 4.527154] sata_mv f1080000.sata: slots 32 ports 2 [ 4.557782] scsi host0: usb-storage 1-1.2:1.0 [ 4.571040] usbcore: registered new interface driver usb-storage [ 4.577252] scsi host1: sata_mv [ 4.593415] scsi host2: sata_mv [ 4.596926] ata1: SATA max UDMA/133 irq 32 [ 4.601040] ata2: SATA max UDMA/133 irq 32 [ 4.616359] usbcore: registered new interface driver uas [ 4.993318] ata1: SATA link down (SStatus 0 SControl F300) [ 5.363306] ata2: SATA link down (SStatus 0 SControl F300) [ 5.554837] scsi 0:0:0:0: Direct-Access Kingston DataTraveler G3 PMAP PQ: 0 ANSI: 0 CCS [ 5.570061] sd 0:0:0:0: [sda] 7669824 512-byte logical blocks: (3.92 GB/3.65 GiB) [ 5.580536] sd 0:0:0:0: [sda] Write Protect is off [ 5.585895] sd 0:0:0:0: [sda] No Caching mode page found [ 5.591234] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 5.603332] sda: sda1 [ 5.609147] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 5.618533] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Checking root file system ... fsck from util-linux 2.25.2 rootfs: clean, 14520/240000 files, 150818/958472 blocks done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 16.968678] systemd-udevd[295]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 17.480523] marvell-cesa: probe of f1030000.crypto failed with error -524 [ 17.529648] orion_wdt: Initial timeout 21 sec done. [....] Activating swap...[ 18.384036] random: nonblocking pool is initialized [ ok done. [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 14520/240000 files, 150818/958472 blocks done. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 21.280384] NET: Registered protocol family 10 [ 22.446940] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/xx:xx:xx:xx:xx:xx Sending on LPF/eth0/xx:xx:xx:xx:xx:xx Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 No DHCPOFFERS received. Trying recorded lease 192.168.0.16 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. --- 192.168.0.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms bound: renewal in 4704 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1226 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1223 (klogd) . ok not Debian GNU/Linux 8 debian ttyS0 debian login:
Re: Dockstar - no network April 20, 2017 04:14AM |
Admin Registered: 13 years ago Posts: 18,495 |
Quote
> A couple interesting lines:
> [ 0.160991] [Firmware Info]: /ocp@f1000000/ethe
> rnet-controller@72000/ethernet0-port@0: local-mac-
> address is not set
Quote
[ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Seagate GoFlex Net
Quote
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts).
Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-4.4.0-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.4.0-kirkwood-tld-1 -d zImage.fdt uImage
sync
cat dts/kirkwood-dockstar.dtb >> zImage.fdt
Re: Dockstar - no network April 20, 2017 06:28AM |
Registered: 6 years ago Posts: 57 |
U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1752 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1731 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 (usbda1) 3165294 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 7179935 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3165230 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Seagate FreeAgent Dockstar [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 113632K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000335] Console: colour dummy device 80x30 [ 0.000367] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090105] pid_max: default: 32768 minimum: 301 [ 0.090215] Security Framework initialized [ 0.090291] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090312] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091115] Initializing cgroup subsys io [ 0.091149] Initializing cgroup subsys devices [ 0.091174] Initializing cgroup subsys freezer [ 0.091206] Initializing cgroup subsys net_cls [ 0.091289] CPU: Testing write buffer coherency: ok [ 0.091766] Setting up static identity map for 0x8200 - 0x8258 [ 0.092067] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.095847] devtmpfs: initialized [ 0.100508] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100981] prandom: seed boundary self test passed [ 0.104740] prandom: 100 self tests passed [ 0.104767] pinctrl core: initialized pinctrl subsystem [ 0.106185] NET: Registered protocol family 16 [ 0.106659] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130108] cpuidle: using governor ladder [ 0.160107] cpuidle: using governor menu [ 0.160542] Feroceon L2: Enabling L2 [ 0.160589] Feroceon L2: Cache support initialised. [ 0.160973] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.165880] No ATAGs? [ 0.201617] vgaarb: loaded [ 0.201994] usbcore: registered new interface driver usbfs [ 0.202078] usbcore: registered new interface driver hub [ 0.202142] usbcore: registered new device driver usb [ 0.203262] clocksource: Switched to clocksource orion_clocksource [ 0.259082] NET: Registered protocol family 2 [ 0.259902] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.259929] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.259951] TCP: Hash tables configured (established 1024 bind 1024) [ 0.260022] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260046] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260248] NET: Registered protocol family 1 [ 0.260660] RPC: Registered named UNIX socket transport module. [ 0.260673] RPC: Registered udp transport module. [ 0.260680] RPC: Registered tcp transport module. [ 0.260687] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.260973] Unpacking initramfs... [ 0.908000] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 0.908149] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.909265] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.909341] audit: initializing netlink subsys (disabled) [ 0.909396] audit: type=2000 audit(0.900:1): initialized [ 0.909758] Initialise system trusted keyring [ 0.910153] zbud: loaded [ 0.910457] VFS: Disk quotas dquot_6.6.0 [ 0.910521] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.911078] NFS: Registering the id_resolver key type [ 0.911130] Key type id_resolver registered [ 0.911140] Key type id_legacy registered [ 0.911166] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.911181] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.911409] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.911941] Key type big_key registered [ 0.932385] Key type asymmetric registered [ 0.932408] Asymmetric key parser 'x509' registered [ 0.932509] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.932532] io scheduler noop registered [ 0.932548] io scheduler deadline registered [ 0.932611] io scheduler cfq registered (default) [ 0.934106] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.934779] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 0.935205] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 0.935744] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.973970] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.974209] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.013953] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.014452] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.015877] console [ttyS0] disabled [ 1.015943] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 1.617268] console [ttyS0] enabled [ 1.622152] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 1.628574] nand: Micron MT29F2G08AAD [ 1.632255] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.639885] Scanning device for bad blocks [ 1.801018] 4 cmdlinepart partitions found on MTD device orion_nand [ 1.807334] Creating 4 MTD partitions on "orion_nand": [ 1.812507] 0x000000000000-0x000000100000 : "u-boot" [ 1.818873] 0x000000100000-0x000000500000 : "uImage" [ 1.825137] 0x000000500000-0x000002500000 : "rootfs" [ 1.831375] 0x000002500000-0x000010000000 : "data" [ 1.838851] libphy: Fixed MDIO Bus: probed [ 1.843374] libphy: orion_mdio_bus: probed [ 1.852479] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.933949] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address xx:xx:xx:xx:xx:xx [ 2.942838] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.949452] ehci-pci: EHCI PCI platform driver [ 2.954020] ehci-orion: EHCI orion driver [ 2.958230] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.963801] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.971751] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.993296] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.999560] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.006409] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.013688] usb usb1: Product: EHCI Host Controller [ 3.018587] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 3.025250] usb usb1: SerialNumber: f1050000.ehci [ 3.030747] hub 1-0:1.0: USB hub found [ 3.034602] hub 1-0:1.0: 1 port detected [ 3.039549] mousedev: PS/2 mouse device common for all mice [ 3.353296] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 3.505008] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 3.511759] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.518966] usb 1-1: Product: USB2.0 Hub [ 3.523874] hub 1-1:1.0: USB hub found [ 3.528009] hub 1-1:1.0: 4 ports detected [ 3.813289] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 3.927380] usb 1-1.2: New USB device found, idVendor=0930, idProduct=6545 [ 3.934321] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.941690] usb 1-1.2: Product: DataTraveler G3 [ 3.946266] usb 1-1.2: Manufacturer: Kingston [ 3.950641] usb 1-1.2: SerialNumber: 001372970D64EB60A51101AE [ 4.053299] rtc-mv f1010300.rtc: internal RTC not ticking [ 4.058930] i2c /dev entries driver [ 4.063834] hidraw: raw HID events driver (C) Jiri Kosina [ 4.069649] drop_monitor: Initializing network drop monitor service [ 4.076232] NET: Registered protocol family 17 [ 4.080962] Key type dns_resolver registered [ 4.086161] registered taskstats version 1 [ 4.090325] Loading compiled-in X.509 certificates [ 4.095261] zswap: loaded using pool lzo/zbud [ 4.108630] Key type encrypted registered [ 4.113204] hctosys: unable to open rtc device (rtc0) [ 4.120689] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 4.198206] systemd-udevd[83]: starting version 215 [ 4.215339] random: systemd-udevd urandom read with 7 bits of entropy available [ 4.372050] SCSI subsystem initialized [ 4.417079] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 4.469457] scsi host0: usb-storage 1-1.2:1.0 [ 4.482624] usbcore: registered new interface driver usb-storage [ 4.510818] usbcore: registered new interface driver uas [ 5.474734] scsi 0:0:0:0: Direct-Access Kingston DataTraveler G3 PMAP PQ: 0 ANSI: 0 CCS [ 5.492457] sd 0:0:0:0: [sda] 7669824 512-byte logical blocks: (3.92 GB/3.65 GiB) [ 5.500925] sd 0:0:0:0: [sda] Write Protect is off [ 5.506292] sd 0:0:0:0: [sda] No Caching mode page found [ 5.511651] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 5.523787] sda: sda1 [ 5.529419] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 5.539174] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Checking root file system ... fsck from util-linux 2.25.2 rootfs was not cleanly unmounted, check forced. [ 19.478397] random: nonblocking pool is initialized rootfs: 14523/240000 files (6.3% non-contiguous), 150829/958472 blocks fsck exited with status code 1 done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 21.519454] systemd-udevd[289]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 22.015336] orion_wdt: Initial timeout 21 sec [ 22.098536] marvell-cesa: probe of f1030000.crypto failed with error -524 done. [ ok ] Activating swap...done. [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 14523/240000 files, 150829/958472 blocks done. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 25.802386] NET: Registered protocol family 10 [ 26.966804] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/xx:xx:xx:xx:xx:xx Sending on LPF/eth0/xx:xx:xx:xx:xx:xx Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 No DHCPOFFERS received. Trying recorded lease 192.168.0.16 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. --- 192.168.0.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms bound: renewal in 244 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1215 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1219 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login:
Re: Dockstar - no network April 20, 2017 03:31PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 20, 2017 07:46PM |
Registered: 6 years ago Posts: 57 |
Re: Dockstar - no network April 20, 2017 08:09PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 21, 2017 03:20AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 21, 2017 06:10AM |
Registered: 6 years ago Posts: 57 |
U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 u-boot>> setenv ipaddr 192.168.1.99 u-boot>> printenv ipaddr ipaddr=192.168.1.99 u-boot>> ping 192.168.1.1 No link on egiga0 ping failed; host 192.168.1.1 is not alive u-boot>>
Re: Dockstar - no network April 21, 2017 04:18PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 21, 2017 05:21PM |
Registered: 6 years ago Posts: 57 |
U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 3 ^H^H^H 2 ^H^H^H 1 ^H^H^H 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1752 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1731 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ^H^H. ^H^H. ^H^H. ^H^H. ^H^H. ^H^H. ^H^H. read_nand_cached: error reading nand off 0x122e400 size 8192 bytes ^H^H. ^H^H. read_nand_cached: error reading nand off 0x1afc200 size 8192 bytes ^H^H done.^M read_nand_cached: error reading nand off 0x122f000 size 8192 bytes off = 0x122e9f0 magic 0x1985 type 0xe002 node.totlen = 2444 read_nand_cached: error reading nand off 0x1afc000 size 8192 bytes off = 0x1afbf24 magic 0x1985 type 0xe002 node.totlen = 446 ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
Re: Dockstar - no network April 21, 2017 06:44PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 21, 2017 09:26PM |
Registered: 6 years ago Posts: 57 |
1. Download your mtd2 rootfs http://forum.doozan.com/read.php?3,31993,32082#msg-32082 2. Download NAND and U-Boot tools (for flash_eraseall) http://forum.doozan.com/read.php?3,27280 3. Download ubiformat http://jeff.doozan.com/debian/rescue/ubiformat 4. Erase rootfs flash_eraseall /dev/mtd2 5. Format/Write rootfs ubiformat /dev/mtd2 -s 512 -f pogoplug_e02_mtd2
Re: Dockstar - no network April 22, 2017 04:14PM |
Admin Registered: 13 years ago Posts: 18,495 |
nanddump --noecc --omitoob .......So you need to verify the option in the nanddump version that you are using below for options --noecc --omitoob
nandwrite --help
nandwrite -n /dev/mtd2 mtd2
Re: Dockstar - no network April 22, 2017 10:20PM |
Registered: 6 years ago Posts: 57 |
> nanddump --noecc --omitoob ....... >> So you need to verify the option in the nanddump v
> nandwrite --help >>
> nandwrite -n /dev/mtd2 mtd2 >
root@debian:~/tools# ./nandwrite --help Usage: nandwrite [OPTION] MTD_DEVICE [INPUTFILE|-] Writes to the specified MTD device. -a, --autoplace Use auto OOB layout -m, --markbad Mark blocks bad if write fails -n, --noecc Write without ecc -N, --noskipbad Write without bad block skipping -o, --oob Input contains oob data -O, --onlyoob Input contains oob data and only write the oob part -s addr, --start=addr Set output start address (default is 0) -p, --pad Pad writes to page size -b, --blockalign=1|2|4 Set multiple of eraseblocks to align to --input-skip=length Skip |length| bytes of the input file --input-size=length Only read |length| bytes of the input file -q, --quiet Don't display progress messages -h, --help Display this help and exit --version Output version information and exit
Re: Dockstar - no network April 23, 2017 04:01PM |
Admin Registered: 13 years ago Posts: 18,495 |
nandwrite -n /dev/mtd2 mtd2
Re: Dockstar - no network April 23, 2017 06:59PM |
Registered: 6 years ago Posts: 57 |
root@debian:~/tools# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00400000 00020000 "uImage" mtd2: 02000000 00020000 "rootfs" mtd3: 0db00000 00020000 "data"
Re: Dockstar - no network April 23, 2017 08:49PM |
Admin Registered: 13 years ago Posts: 18,495 |
flash_erase /dev/mtd2 0 0
Re: Dockstar - no network April 23, 2017 09:23PM |
Registered: 6 years ago Posts: 57 |
read_nand_cached: error reading nand off 0x7a7a00 size 8192 bytes read_nand_cached: error reading nand off 0x809600 size 8192 bytes read_nand_cached: error reading nand off 0x889a00 size 8192 bytes read_nand_cached: error reading nand off 0x8a2000 size 8192 bytes read_nand_cached: error reading nand off 0xca6200 size 8192 bytes read_nand_cached: error reading nand off 0xcad000 size 8192 bytes read_nand_cached: error reading nand off 0xde7800 size 8192 bytes read_nand_cached: error reading nand off 0xe2b800 size 8192 bytes read_nand_cached: error reading nand off 0xe8a000 size 8192 bytes read_nand_cached: error reading nand off 0xeac800 size 8192 bytes read_nand_cached: error reading nand off 0xeaf000 size 8192 bytes find_inode failed for name=uboot-original-mtd0.kwb load: Failed to find inode ### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb! resetting ... U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 u-boot>>
Re: Dockstar - no network April 23, 2017 09:42PM |
Admin Registered: 13 years ago Posts: 18,495 |
> read_nand_cached: error reading nand off 0x7a7a00 > size 8192 bytes > read_nand_cached: error reading nand off 0x809600 > size 8192 bytes > read_nand_cached: error reading nand off 0x889a00 > size 8192 bytes > read_nand_cached: error reading nand off 0x8a2000 > size 8192 bytes > read_nand_cached: error reading nand off 0xca6200 > size 8192 bytes > read_nand_cached: error reading nand off 0xcad000 > size 8192 bytes > read_nand_cached: error reading nand off 0xde7800 > size 8192 bytes > read_nand_cached: error reading nand off 0xe2b800 > size 8192 bytes > read_nand_cached: error reading nand off 0xe8a000 > size 8192 bytes > read_nand_cached: error reading nand off 0xeac800 > size 8192 bytes > read_nand_cached: error reading nand off 0xeaf000 > size 8192 bytes > find_inode failed for name=uboot-original-mtd0.kwb > load: Failed to find inode > ### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kw > b! > resetting ... > > > U-Boot 2011.12 (Feb 12 2012 - 21:33:07) > Seagate FreeAgent DockStar > > SoC: Kirkwood 88F6281_A0 > DRAM: 128 MiB > WARNING: Caches not enabled > NAND: 256 MiB > In: serial > Out: serial > Err: serial > Net: egiga0 > 88E1116 Initialized on egiga0 > Hit any key to stop autoboot: 0 > u-boot>> >
Re: Dockstar - no network April 23, 2017 09:51PM |
Registered: 6 years ago Posts: 57 |
Re: Dockstar - no network April 23, 2017 11:48PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Dockstar - no network April 24, 2017 05:54AM |
Registered: 6 years ago Posts: 57 |
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Seagate FreeAgent Dockstar [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c08a06b4, node_mem_map c7ef9000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 113632K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) .init : 0xc07d8000 - 0xc0822000 ( 296 kB) .data : 0xc0822000 - 0xc08b169c ( 574 kB) .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000335] Console: colour dummy device 80x30 [ 0.000367] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090105] pid_max: default: 32768 minimum: 301 [ 0.090215] Security Framework initialized [ 0.090292] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090313] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091113] Initializing cgroup subsys io [ 0.091150] Initializing cgroup subsys devices [ 0.091175] Initializing cgroup subsys freezer [ 0.091207] Initializing cgroup subsys net_cls [ 0.091291] CPU: Testing write buffer coherency: ok [ 0.091767] Setting up static identity map for 0x8200 - 0x8258 [ 0.092069] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.095848] devtmpfs: initialized [ 0.100508] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100982] prandom: seed boundary self test passed [ 0.104740] prandom: 100 self tests passed [ 0.104767] pinctrl core: initialized pinctrl subsystem [ 0.106185] NET: Registered protocol family 16 [ 0.106660] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130108] cpuidle: using governor ladder [ 0.160107] cpuidle: using governor menu [ 0.160542] Feroceon L2: Enabling L2 [ 0.160589] Feroceon L2: Cache support initialised. [ 0.160973] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.165880] No ATAGs? [ 0.201617] vgaarb: loaded [ 0.201994] usbcore: registered new interface driver usbfs [ 0.202078] usbcore: registered new interface driver hub [ 0.202142] usbcore: registered new device driver usb [ 0.203262] clocksource: Switched to clocksource orion_clocksource [ 0.259067] NET: Registered protocol family 2 [ 0.259890] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.259917] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.259937] TCP: Hash tables configured (established 1024 bind 1024) [ 0.260009] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260033] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260236] NET: Registered protocol family 1 [ 0.260647] RPC: Registered named UNIX socket transport module. [ 0.260660] RPC: Registered udp transport module. [ 0.260668] RPC: Registered tcp transport module. [ 0.260676] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.260698] PCI: CLS 0 bytes, default 32 [ 0.260963] Unpacking initramfs... [ 0.907941] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 0.908088] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.909209] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.909286] audit: initializing netlink subsys (disabled) [ 0.909340] audit: type=2000 audit(0.900:1): initialized [ 0.909700] Initialise system trusted keyring [ 0.910106] zbud: loaded [ 0.910411] VFS: Disk quotas dquot_6.6.0 [ 0.910473] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.911033] NFS: Registering the id_resolver key type [ 0.911072] Key type id_resolver registered [ 0.911082] Key type id_legacy registered [ 0.911108] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.911123] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.911352] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 0.911886] Key type big_key registered [ 0.932308] Key type asymmetric registered [ 0.932331] Asymmetric key parser 'x509' registered [ 0.932433] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.932455] io scheduler noop registered [ 0.932470] io scheduler deadline registered [ 0.932534] io scheduler cfq registered (default) [ 0.934115] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.934796] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 0.935222] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 0.935762] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.973970] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.974209] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.013941] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.014442] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.015861] console [ttyS0] disabled [ 1.015927] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 1.617242] console [ttyS0] enabled [ 1.622126] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 1.628547] nand: Micron MT29F2G08AAD [ 1.632228] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.639859] Scanning device for bad blocks [ 1.801029] 4 cmdlinepart partitions found on MTD device orion_nand [ 1.807343] Creating 4 MTD partitions on "orion_nand": [ 1.812517] 0x000000000000-0x000000100000 : "u-boot" [ 1.818874] 0x000000100000-0x000000500000 : "uImage" [ 1.825136] 0x000000500000-0x000002500000 : "rootfs" [ 1.831383] 0x000002500000-0x000010000000 : "data" [ 1.838852] libphy: Fixed MDIO Bus: probed [ 1.843374] libphy: orion_mdio_bus: probed [ 1.852489] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.933955] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address xx:xx:xx:xx:xx:xx [ 2.942839] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.949463] ehci-pci: EHCI PCI platform driver [ 2.954028] ehci-orion: EHCI orion driver [ 2.958239] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.963811] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.971746] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.993298] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.999561] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.006408] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.013689] usb usb1: Product: EHCI Host Controller [ 3.018587] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 3.025250] usb usb1: SerialNumber: f1050000.ehci [ 3.030749] hub 1-0:1.0: USB hub found [ 3.034605] hub 1-0:1.0: 1 port detected [ 3.039553] mousedev: PS/2 mouse device common for all mice [ 3.353296] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 3.504876] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 3.511629] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.518836] usb 1-1: Product: USB2.0 Hub [ 3.523751] hub 1-1:1.0: USB hub found [ 3.527878] hub 1-1:1.0: 4 ports detected [ 3.813289] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 3.930497] usb 1-1.2: New USB device found, idVendor=058f, idProduct=6387 [ 3.937434] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.944816] usb 1-1.2: Product: Mass Storage [ 3.949107] usb 1-1.2: SerialNumber: 02CB61F5 [ 4.053295] rtc-mv f1010300.rtc: internal RTC not ticking [ 4.058932] i2c /dev entries driver [ 4.063841] hidraw: raw HID events driver (C) Jiri Kosina [ 4.069658] drop_monitor: Initializing network drop monitor service [ 4.076244] NET: Registered protocol family 17 [ 4.080976] Key type dns_resolver registered [ 4.086188] registered taskstats version 1 [ 4.090353] Loading compiled-in X.509 certificates [ 4.095287] zswap: loaded using pool lzo/zbud [ 4.108667] Key type encrypted registered [ 4.113245] hctosys: unable to open rtc device (rtc0) [ 4.119585] PM: Hibernation image not present or could not be loaded. [ 4.120734] Freeing unused kernel memory: 296K (c07d8000 - c0822000) [ 4.197800] systemd-udevd[83]: starting version 215 [ 4.214953] random: systemd-udevd urandom read with 7 bits of entropy available [ 4.390410] SCSI subsystem initialized [ 4.420848] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 4.465408] scsi host0: usb-storage 1-1.2:1.0 [ 4.478630] usbcore: registered new interface driver usb-storage [ 4.506336] usbcore: registered new interface driver uas [ 5.465603] scsi 0:0:0:0: Direct-Access USB Disk 8.07 PQ: 0 ANSI: 4 [ 5.483441] sd 0:0:0:0: [sda] 62095360 512-byte logical blocks: (31.7 GB/29.6 GiB) [ 5.491920] sd 0:0:0:0: [sda] Write Protect is off [ 5.496819] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 5.497785] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.513786] sda: sda1 [ 5.520161] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 5.529948] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 19.881567] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2 [ 22.924443] random: nonblocking pool is initialized [ 23.011003] systemd-udevd[287]: starting version 215 [ 24.074999] orion_wdt: Initial timeout 21 sec [ 24.253966] marvell-cesa: probe of f1030000.crypto failed with error -524 [ 29.243909] NET: Registered protocol family 10 [ 30.577241] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready