Welcome! Log In Create A New Profile

Advanced

Help unbricking IOmega ix4-200d

Posted by Red9r 
Help unbricking IOmega ix4-200d
May 22, 2017 04:45PM
Help! I have two IX4-200D NAS boxes that are currently useless. The original hard dives are gone and have been replaced with larger 4 TB Seagate NAS Hard drives. I'm fairly new to this and was hoping someone could provide assistance with installing Debian to get them back up and running. I have my console hooked up and can see the units boot in Putty but I'm not sure where to go from there. Thanks in advance and I'm looking forward to the opportunity to learn.



Edited 1 time(s). Last edit at 05/22/2017 07:41PM by Red9r.
Re: Help unbricking IOmega ix4-200d
May 23, 2017 05:43AM
Red9r Wrote:
-------------------------------------------------------
> Help! I have two IX4-200D NAS boxes that are curre
> ntly useless. The original hard dives are gone and
> have been replaced with larger 4 TB Seagate NAS Ha
> rd drives. I'm fairly new to this and was hoping s
> omeone could provide assistance with installing De
> bian to get them back up and running. I have my co
> nsole hooked up and can see the units boot in Put
> ty but I'm not sure where to go from there. Thanks
> in advance and I'm looking forward to the opportun
> ity to learn.

Connect serial console, power up. Please capture the entire putty log (from u-boot banner until it fails to boot), and post it here (in code tags).

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Help unbricking IOmega ix4-200d
May 23, 2017 05:08PM
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.05.23 17:03:14 =~=~=~=~=~=~=~=~=~=~=~=

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__|  ** uboot_ver:v1.1.1 **

 ** MARVELL BOARD: IX4-110 LE 

U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CF600

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB 
DRAM CS[1] base 0x10000000   size 256MB 
DRAM Total size 512MB  16bit width
Found 0x20 i2c device
Toggle power status
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90)  OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60)  OK

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:             Z30403WL
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
[0 1 0]: Enable DMA mode (6)
  Device 1 @ 0 1:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:             Z30404FV
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)


CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d8000

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is RGMII

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI:  AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part 
scanning bus for devices...
  Device 0: (0:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
  Device 1: (1:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  1  0 

NAND read: device 0 offset 0xb0000, size 0x228000


Reading data from 0xb0000 --   0% complete.
Reading data from 0xb5800 --   1% complete.
Reading data from 0xbb000 --   2% complete.
Reading data from 0xc0800 --   3% complete.
Reading data from 0xc6000 --   4% complete.
Reading data from 0xcb800 --   5% complete.
Reading data from 0xd1000 --   6% complete.
Reading data from 0xd6a00 --   7% complete.
Reading data from 0xdc200 --   8% complete.
Reading data from 0xe1a00 --   9% complete.
Reading data from 0xe7200 --  10% complete.
Reading data from 0xeca00 --  11% complete.
Reading data from 0xf2200 --  12% complete.
Reading data from 0xf7c00 --  13% complete.
Reading data from 0xfd400 --  14% complete.
Reading data from 0x102c00 --  15% complete.
Reading data from 0x108400 --  16% complete.
Reading data from 0x10dc00 --  17% complete.
Reading data from 0x113400 --  18% complete.
Reading data from 0x118e00 --  19% complete.
Reading data from 0x11e600 --  20% complete.
Reading data from 0x123e00 --  21% complete.
Reading data from 0x129600 --  22% complete.
Reading data from 0x12ee00 --  23% complete.
Reading data from 0x134600 --  24% complete.
Reading data from 0x139e00 --  25% complete.
Reading data from 0x13f800 --  26% complete.
Reading data from 0x145000 --  27% complete.
Reading data from 0x14a800 --  28% complete.
Reading data from 0x150000 --  29% complete.
Reading data from 0x155800 --  30% complete.
Reading data from 0x15b000 --  31% complete.
Reading data from 0x160a00 --  32% complete.
Reading data from 0x166200 --  33% complete.
Reading data from 0x16ba00 --  34% complete.
Reading data from 0x171200 --  35% complete.
Reading data from 0x176a00 --  36% complete.
Reading data from 0x17c200 --  37% complete.
Reading data from 0x181c00 --  38% complete.
Reading data from 0x187400 --  39% complete.
Reading data from 0x18cc00 --  40% complete.
Reading data from 0x192400 --  41% complete.
Reading data from 0x197c00 --  42% complete.
Reading data from 0x19d400 --  43% complete.
Reading data from 0x1a2e00 --  44% complete.
Reading data from 0x1a8600 --  45% complete.
Reading data from 0x1ade00 --  46% complete.
Reading data from 0x1b3600 --  47% complete.
Reading data from 0x1b8e00 --  48% complete.
Reading data from 0x1be600 --  49% complete.
Reading data from 0x1c3e00 --  50% complete.
Reading data from 0x1c9800 --  51% complete.
Reading data from 0x1cf000 --  52% complete.
Reading data from 0x1d4800 --  53% complete.
Reading data from 0x1da000 --  54% complete.
Reading data from 0x1df800 --  55% complete.
Reading data from 0x1e5000 --  56% complete.
Reading data from 0x1eaa00 --  57% complete.
Reading data from 0x1f0200 --  58% complete.
Reading data from 0x1f5a00 --  59% complete.
Reading data from 0x1fb200 --  60% complete.
Reading data from 0x200a00 --  61% complete.
Reading data from 0x206200 --  62% complete.
Reading data from 0x20bc00 --  63% complete.
Reading data from 0x211400 --  64% complete.
Reading data from 0x216c00 --  65% complete.
Reading data from 0x21c400 --  66% complete.
Reading data from 0x221c00 --  67% complete.
Reading data from 0x227400 --  68% complete.
Reading data from 0x22ce00 --  69% complete.
Reading data from 0x232600 --  70% complete.
Reading data from 0x237e00 --  71% complete.
Reading data from 0x23d600 --  72% complete.
Reading data from 0x242e00 --  73% complete.
Reading data from 0x248600 --  74% complete.
Reading data from 0x24de00 --  75% complete.
Reading data from 0x253800 --  76% complete.
Reading data from 0x259000 --  77% complete.
Reading data from 0x25e800 --  78% complete.
Reading data from 0x264000 --  79% complete.
Reading data from 0x269800 --  80% complete.
Reading data from 0x26f000 --  81% complete.
Reading data from 0x274a00 --  82% complete.
Reading data from 0x27a200 --  83% complete.
Reading data from 0x27fa00 --  84% complete.
Reading data from 0x285200 --  85% complete.
Reading data from 0x28aa00 --  86% complete.
Reading data from 0x290200 --  87% complete.
Reading data from 0x295c00 --  88% complete.
Reading data from 0x29b400 --  89% complete.
Reading data from 0x2a0c00 --  90% complete.
Reading data from 0x2a6400 --  91% complete.
Reading data from 0x2abc00 --  92% complete.
Reading data from 0x2b1400 --  93% complete.
Reading data from 0x2b6e00 --  94% complete.
Reading data from 0x2bc600 --  95% complete.
Reading data from 0x2c1e00 --  96% complete.
Reading data from 0x2c7600 --  97% complete.
Reading data from 0x2cce00 --  98% complete.
Reading data from 0x2d2600 --  99% complete.
Reading data from 0x2d7e00 -- 100% complete.
 2260992 bytes read: OK

NAND read: device 0 offset 0x2d8000, size 0x300000


Reading data from 0x2d8000 --   0% complete.
Reading data from 0x2dfa00 --   1% complete.
Reading data from 0x2e7400 --   2% complete.
Reading data from 0x2ef000 --   3% complete.
Reading data from 0x2f6a00 --   4% complete.
Reading data from 0x2fe600 --   5% complete.
Reading data from 0x306000 --   6% complete.
Reading data from 0x30dc00 --   7% complete.
Reading data from 0x315600 --   8% complete.
Reading data from 0x31d000 --   9% complete.
Reading data from 0x324c00 --  10% complete.
Reading data from 0x32c600 --  11% complete.
Reading data from 0x334200 --  12% complete.
Reading data from 0x33bc00 --  13% complete.
Reading data from 0x343800 --  14% complete.
Reading data from 0x34b200 --  15% complete.
Reading data from 0x352e00 --  16% complete.
Reading data from 0x35a800 --  17% complete.
Reading data from 0x362200 --  18% complete.
Reading data from 0x369e00 --  19% complete.
Reading data from 0x371800 --  20% complete.
Reading data from 0x379400 --  21% complete.
Reading data from 0x380e00 --  22% complete.
Reading data from 0x388a00 --  23% complete.
Reading data from 0x390400 --  24% complete.
Reading data from 0x397e00 --  25% complete.
Reading data from 0x39fa00 --  26% complete.
Reading data from 0x3a7400 --  27% complete.
Reading data from 0x3af000 --  28% complete.
Reading data from 0x3b6a00 --  29% complete.
Reading data from 0x3be600 --  30% complete.
Reading data from 0x3c6000 --  31% complete.
Reading data from 0x3cdc00 --  32% complete.
Reading data from 0x3d5600 --  33% complete.
Reading data from 0x3dd000 --  34% complete.
Reading data from 0x3e4c00 --  35% complete.
Reading data from 0x3ec600 --  36% complete.
Reading data from 0x3f4200 --  37% complete.
Reading data from 0x3fbc00 --  38% complete.
Reading data from 0x403800 --  39% complete.
Reading data from 0x40b200 --  40% complete.
Reading data from 0x412e00 --  41% complete.
Reading data from 0x41a800 --  42% complete.
Reading data from 0x422200 --  43% complete.
Reading data from 0x429e00 --  44% complete.
Reading data from 0x431800 --  45% complete.
Reading data from 0x439400 --  46% complete.
Reading data from 0x440e00 --  47% complete.
Reading data from 0x448a00 --  48% complete.
Reading data from 0x450400 --  49% complete.
Reading data from 0x457e00 --  50% complete.
Reading data from 0x45fa00 --  51% complete.
Reading data from 0x467400 --  52% complete.
Reading data from 0x46f000 --  53% complete.
Reading data from 0x476a00 --  54% complete.
Reading data from 0x47e600 --  55% complete.
Reading data from 0x486000 --  56% complete.
Reading data from 0x48dc00 --  57% complete.
Reading data from 0x495600 --  58% complete.
Reading data from 0x49d000 --  59% complete.
Reading data from 0x4a4c00 --  60% complete.
Reading data from 0x4ac600 --  61% complete.
Reading data from 0x4b4200 --  62% complete.
Reading data from 0x4bbc00 --  63% complete.
Reading data from 0x4c3800 --  64% complete.
Reading data from 0x4cb200 --  65% complete.
Reading data from 0x4d2e00 --  66% complete.
Reading data from 0x4da800 --  67% complete.
Reading data from 0x4e2200 --  68% complete.
Reading data from 0x4e9e00 --  69% complete.
Reading data from 0x4f1800 --  70% complete.
Reading data from 0x4f9400 --  71% complete.
Reading data from 0x500e00 --  72% complete.
Reading data from 0x508a00 --  73% complete.
Reading data from 0x510400 --  74% complete.
Reading data from 0x517e00 --  75% complete.
Reading data from 0x51fa00 --  76% complete.
Reading data from 0x527400 --  77% complete.
Reading data from 0x52f000 --  78% complete.
Reading data from 0x536a00 --  79% complete.
Reading data from 0x53e600 --  80% complete.
Reading data from 0x546000 --  81% complete.
Reading data from 0x54dc00 --  82% complete.
Reading data from 0x555600 --  83% complete.
Reading data from 0x55d000 --  84% complete.
Reading data from 0x564c00 --  85% complete.
Reading data from 0x56c600 --  86% complete.
Reading data from 0x574200 --  87% complete.
Reading data from 0x57bc00 --  88% complete.
Reading data from 0x583800 --  89% complete.
Reading data from 0x58b200 --  90% complete.
Reading data from 0x592e00 --  91% complete.
Reading data from 0x59a800 --  92% complete.
Reading data from 0x5a2200 --  93% complete.
Reading data from 0x5a9e00 --  94% complete.
Reading data from 0x5b1800 --  95% complete.
Reading data from 0x5b9400 --  96% complete.
Reading data from 0x5c0e00 --  97% complete.
Reading data from 0x5c8a00 --  98% complete.
Reading data from 0x5d0400 --  99% complete.
Reading data from 0x5d7e00 -- 100% complete.
 3145728 bytes read: OK
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2012-01-05  18:29:43 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1910204 Bytes =  1.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 12000000 ...
   Image Name:   
   Created:      2012-05-02  20:38:45 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1831340 Bytes =  1.7 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux.......................................................................................................................... done, booting the kernel.

Linux version 2.6.22.18 (soho@bsoho149.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 Thu Jan 5 13:29:36 EST 2012
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x228000@0xb0000(zImage),0x300000@0x2d8000(initrd),32m@0x0(flash)
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB 0MB 0MB = 512MB total
Memory: 513920KB available (3520K code, 283K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB 
SDRAM_CS1 ....base 10000000, size 256MB 
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
NFLASH_CS ....base fa000000, size   2MB 
SPI_CS ....base f4000000, size  16MB 
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB 

  Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- IX4-110  Soc: 88F6281 A1 LE

 Detected Tclk 200000000 and SysClk 400000000 
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c0876600
PEX0 interface detected Link X1
PCI: bus0: Fast back to back transfers disabled
SCSI Scattered Spinup:
SCSI Scattered Spinup Feature Status: Enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1788K
RTC registered
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
Number of XOR engines to use: 4
cesadev_init(c0011e28)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
Registering unionfs 2.5.1 (for 2.6.22.19)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 5120K size 1024 blocksize
loop: module loaded
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload enabled
  o Receive checksum offload enabled
  o Transmit checksum offload enabled
  o Network Fast Processing (Routing) supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Proc tool API enabled
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
    o eth0, ifindex = 1, GbE port = 0
    o eth1, ifindex = 2, GbE port = 1

mvFpRuleDb (c0b00000): 16384 entries, 65536 bytes
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Marvell Storage Controller is found, using IRQ 9.
scsi0 : Marvell Storage Controller
scsi 0:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
scsi 0:0:4:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
Integrated Sata device found
scsi1 : Marvell SCSI to SATA adapter
scsi2 : Marvell SCSI to SATA adapter
scsi 1:0:0:0: Direct-Access     Seagate  ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
scsi 2:0:0:0: Direct-Access     Seagate  ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
sd 0:0:0:0: [sda] 7814037168 512-byte hardware sectors (4000787 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
sd 0:0:0:0: [sda] 7814037168 512-byte hardware sectors (4000787 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:4:0: [sdb] Very big device. Trying to use READ CAPACITY(16).
sd 0:0:4:0: [sdb] 7814037168 512-byte hardware sectors (4000787 MB)
sd 0:0:4:0: [sdb] Write Protect is off
sd 0:0:4:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:4:0: [sdb] Very big device. Trying to use READ CAPACITY(16).
sd 0:0:4:0: [sdb] 7814037168 512-byte hardware sectors (4000787 MB)
sd 0:0:4:0: [sdb] Write Protect is off
sd 0:0:4:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sdb: sdb1
sd 0:0:4:0: [sdb] Attached SCSI disk
sd 1:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
sd 1:0:0:0: [sdc] 7814037168 512-byte hardware sectors (4000787 MB)
sd 1:0:0:0: [sdc] Write Protect is off
sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 1:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
sd 1:0:0:0: [sdc] 7814037168 512-byte hardware sectors (4000787 MB)
sd 1:0:0:0: [sdc] Write Protect is off
sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sdc: sdc1
sd 1:0:0:0: [sdc] Attached SCSI disk
sd 2:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16).
sd 2:0:0:0: [sdd] 7814037168 512-byte hardware sectors (4000787 MB)
sd 2:0:0:0: [sdd] Write Protect is off
sd 2:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 2:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16).
sd 2:0:0:0: [sdd] 7814037168 512-byte hardware sectors (4000787 MB)
sd 2:0:0:0: [sdd] Write Protect is off
sd 2:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sdd: sdd1
sd 2:0:0:0: [sdd] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:4:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: Attached scsi generic sg3 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Hynix NAND 32MiB 3,3V 8-bit)
Scanning device for bad blocks
5 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 5 MTD partitions on "nand_mtd":
0x00000000-0x000a0000 : "uboot"
0x000a0000-0x000b0000 : "env"
0x000b0000-0x002d8000 : "zImage"
0x002d8000-0x005d8000 : "initrd"
0x00000000-0x02000000 : "flash"
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usb 1-1: new high speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
attach_adapter....
adt7473_detect....
adt7473 0-002e: adt7473 chip found
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1     91 MB/s
raid6: int32x2    117 MB/s
raid6: int32x4    129 MB/s
raid6: int32x8     98 MB/s
raid6: using algorithm int32x4 (129 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :  1066.800 MB/sec
   8regs     :   800.000 MB/sec
   32regs    :   874.400 MB/sec
raid5: using function: arm4regs (1066.800 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
wix gpio_init
wix_lcm: WIX LCM driver version 0.1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
sh: 4294967295: out of range
sh: 4294967295: out of range
Changing SYS_UUID to UUID_3
Sys UUID is :
Valid Disk 1 in md0: 
Valid Disk 2 in md0: 
Valid Disk 3 in md0: /dev/sdc1
Valid Disk 4 in md0: /dev/sdd1
USB Device node is /dev/sde1
Trying to see the if the reset button is pressed or not
Started
/dev/btns file does not exist creating it
Opened /dev/btns with fd 3
Reset Key Status: Button Id = 29 Push Count = 0 Release Count = 0
Checking for valid image in hard drives
md: md0 stopped.
mdadm: no recogniseable superblock on /dev/sdc1
mdadm: /dev/sdc1 has no superblock - assembly aborted
e2fsck 1EXT2-fs: unable to read superblock
.41.3 (12-Oct-20FAT: unable to read boot sector
08)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/md0 is mounted.

e2fsck: Invalid argument while trying to open /dev/md0


The superblock could not be read or does not describe a correct ext2
filesystem.  If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
    e2fsck -b 8193 <device>

mount: mounting /dev/md0 on sysroot/boot failed: Input/output error
Checking if there is an attached EMC Imager
mount: mounting /dev/sde1 on /usb_drive failed: No such device or address
Going in to Network Imaging Mode
umount: cannot umount /dev/md0: Invalid argument
umount: cannot umount /usb_drive: Invalid argument
eth0: started
udhcpc (v1.9.2) started
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
No lease, failing
Device Model- ix4-200d
Device: Socket Listening on: 2081
Mac address = 00:d0:b8:1f:58:c3
Send: Network is unreachable
Mounting config image...
mount: mounting /sysroot/boot/images/config on /sysroot/boot/etc failed: No such file or directory
umount: cannot umount /sysroot/boot/etc: Invalid argument
umount: cannot umount /dev/md0: Invalid argument
Constructing root filesystem...
cp: cannot stat '/sysroot/mnt/apps/ram': No such file or directory
Bootstrapping ...
Initialization complete.
Freeing init memory: 120K

init started: BusyBox v1.9.2 (2012-01-05 15:00:07 EST)

starting pid 450, tty '': '/etc/init.d/rcS'

starting pid 453, tty '': 'umount'
BusyBox v1.9.2 (2012-01-05 15:00:07 EST) multi-call binary

Usage: umount [flags] FILESYSTEM|DIRECTORY

Unmount file systems

Options:

	-r	Try to remount devices as read-only if mount is busy
	-l	Lazy umount (detach filesystem)
	-f	Force umount (i.e., unreachable NFS server)
	-D	Do not free loop device (if a loop device has been used)


The system is going down NOW!

Sending SIGTERM to all processes

Sending SIGKILL to all processes

Requesting system reboot
md: stopping all md devices.
sd 2:0:0:0: [sdd] Synchronizing SCSI cache
sd 1:0:0:0: [sdc] Synchronizing SCSI cache
sd 0:0:4:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:4:0: [sdb] Synchronizing SCSI cache
Restarting system.
Reseting !!
Re: Help unbricking IOmega ix4-200d
May 24, 2017 01:36PM
Re: Help unbricking IOmega ix4-200d
June 16, 2017 11:15PM
Thank you Bodhi,

I have tried reading through the different threads but I am having trouble piecing it all together. I'm not really sure where to start. I think most people on here have a decent knowledge of the process but this is all new to me. Can you help me get going in the right direction or point me towards some resources that will get me up to speed with what I need to know to tackle this project?

Thanks,
Derek
Re: Help unbricking IOmega ix4-200d
June 16, 2017 11:40PM
I think my biggest issue is that I'm trying to do this from a Windows machine and most everything I am reading in the threads are linux.
Re: Help unbricking IOmega ix4-200d
June 17, 2017 01:53AM
Derek,

It is true, everything here is written in Linux. And they are all command line instructions. But you went pretty far in that you have connected the serial console with Putty and can see what going on in this box. Your log showed that it is booting with stock kernel. So it is not bricked! Our goal is always getting these box to run Debian. And it is doable.

1. You need another Linux system running to install new rootfs and use it to learn Linux. So you could either download Linux Live CD and boot with it on your Windows PC. Or better yet, install a full Linux system such as Linux Mint on a different partition in the Windows PC or on a different USB drive boot with it. And not touching your Windows system. But you can make it permanent by installing on a HDD partition on this Windows PC (and select to boot it in BIOS menu).

I would use 2 USB flash drives, one to put Linux Mint ISO on it using Windows. And boot it up. After you booted Mint installation ISO, plug in another USB drive (about 16GB or 32GB). And then install Mint on it. So you always have a real Linux system to play with.

2. Download the Debian rootfs Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 tarball in this thread:
http://forum.doozan.com/read.php?2,12096

Scroll down to section

Quote

Updated 20 Feb 2016:

This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1.

Basic minimal Debian Kirkwood rootfs for most Kirwood plugs:

- tarball size: 137M
- install size: 398M
- a basic jessie rootfs.
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root

And boot up Linux Mint, bring up Terminal app

- Become root (with su comand).
- Format a USB drive with one Ext3 partition (you need to learn which Linux commands to do this).
- Execute the tar comand as instructed in that section to extract the rootfs tarball to the Ext3 USB drive

3. After you have created the Debian rootfs on USB drive, come back here and I'll point you to the u-boot setup posts that others use to boot this Debian rootfs on the ix4-200d with stock u-boot.

------

So the first important step is to run Linux Mint or Ubuntu on your Windows machine. I recommend Linux Mint with Cinamon desktop. This is a good instruction to start:
https://itsfoss.com/guide-install-linux-mint-16-dual-boot-windows/

It was written for Mint 16, and we are now at Mint 18. So you will download Mint 18.1 here: https://www.linuxmint.com/download.php.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner



Edited 1 time(s). Last edit at 06/17/2017 01:57AM by bodhi.
Re: Help unbricking IOmega ix4-200d
June 19, 2017 11:34PM
bodhi Wrote:
-------------------------------------------------------
> Derek,
>
> It is true, everything here is written in Linux. A
> nd they are all command line instructions. But you
> went pretty far in that you have connected the ser
> ial console with Putty and can see what going on i
> n this box. Your log showed that it is booting wit
> h stock kernel. So it is not bricked! Our goal is
> always getting these box to run Debian. And it is
> doable.
>
> 1. You need another Linux system running to instal
> l new rootfs and use it to learn Linux. So you cou
> ld either download Linux Live CD and boot with it
> on your Windows PC. Or better yet, install a full
> Linux system such as Linux Mint on a different par
> tition in the Windows PC or on a different USB dri
> ve boot with it. And not touching your Windows sy
> stem. But you can make it permanent by installing
> on a HDD partition on this Windows PC (and select
> to boot it in BIOS menu).
>
> I would use 2 USB flash drives, one to put Linux M
> int ISO on it using Windows. And boot it up. After
> you booted Mint installation ISO, plug in another
> USB drive (about 16GB or 32GB). And then install M
> int on it. So you always have a real Linux system
> to play with.
>
> 2. Download the Debian rootfs Debian-4.4.0-kirkwoo
> d-tld-1-rootfs-bodhi.tar.bz2 tarball in this thre
> ad:
> http://forum.doozan.com/read.php?2,12096
>
> Scroll down to section
>
>
Quote

Updated 20 Feb 2016:
>
> This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.
> bz2 is to keep in sync with kernel Linux-4.4.0-kir
> kwood-tld-1.
>
> Basic minimal Debian Kirkwood rootfs for most Kirw
> ood plugs:
>
> - tarball size: 137M
> - install size: 398M
> - a basic jessie rootfs.
> - The init system used in this rootfs is sysvinit
> . To boot with systemd, see note 2 below.
> - Installed packages: nano, avahi, ntp, busybox-sy
> slogd (log to RAM), htop, isc-dhcp-client, dialog,
> bzip2, nfs server/client, iperf, ethtool, sysvinit
> -core, sysvinit, and sysvinit-utils.
> - see LED controls in /etc/rc.local, and /etc/init
> .d/halt
> - see some useful aliases in /root/.profile
> - root password: root
>
> And boot up Linux Mint, bring up Terminal app
>
> - Become root (with su comand).
> - Format a USB drive with one Ext3 partition (you
> need to learn which Linux commands to do this).
> - Execute the tar comand as instructed in that sec
> tion to extract the rootfs tarball to the Ext3 USB
> drive
>
> 3. After you have created the Debian rootfs on USB
> drive, come back here and I'll point you to the u-
> boot setup posts that others use to boot this Debi
> an rootfs on the ix4-200d with stock u-boot.
>
> ------
>
> So the first important step is to run Linux Mint o
> r Ubuntu on your Windows machine. I recommend Linu
> x Mint with Cinamon desktop. This is a good instru
> ction to start:
> https://itsfoss.com/guide-install-linux-mint-16-du
> al-boot-windows/
>
> It was written for Mint 16, and we are now at Mint
> 18. So you will download Mint 18.1 here: https://w
> ww.linuxmint.com/download.php.

Thanks for the excellent instructions Bodhi. I used Linux Mint and successfully formatted a USB drive with the ext3 file system and created the rootfs. I'm ready for the next step.
Re: Help unbricking IOmega ix4-200d
June 20, 2017 01:27AM
Derek,

With serial console connected, and putty (Windows) or picocom (Linux Mint) running. Power up, interrupt serial console (type any key to interrupt it). And get the listing of avialable u-boot commands and u-boot envs:

help
printenv

And post the output of the entire serial console here like you did before.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Help unbricking IOmega ix4-200d
June 20, 2017 08:16PM
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__|  ** uboot_ver:v1.1.1 **

 ** MARVELL BOARD: IX4-110 LE 

U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CF600

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB 
DRAM CS[1] base 0x10000000   size 256MB 
DRAM Total size 512MB  16bit width
Found 0x20 i2c device
Toggle power status
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90)  OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60)  OK

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:             Z30403WL
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
[0 1 0]: Enable DMA mode (6)
  Device 1 @ 0 1:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:             Z30404FV
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)


CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d8000

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is RGMII

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI:  AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part 
scanning bus for devices...
  Device 0: (0:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
  Device 1: (1:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  1  0
Marvell>>   help

?       - alias for 'help'
SatR - sample at reset sub-system, relevent for DB only
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name 
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
bubt	- Burn an image on the Boot Nand Flash.
chpart	- change active partition
cmp     - memory compare
cmpm	- Compare Memory
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
dclk	- Display the MV device CLKs.
dhcp	- invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo    - echo args to console
eeprom  - EEPROM sub-system
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fi	- Find value in the memory.
flinfo  - print FLASH memory information
fsinfo	- print information about filesystems
fsload	- load binary file from a filesystem image
g	- start application at cached address 'addr'(default addr 0x40000)
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
imm[.b, .s, .w, .l]     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
ir	- reading and changing MV internal register values.
loop    - infinite loop on address range
ls	- list files in a directory (default /)
map	- Diasplay address decode windows
md      - memory display
me	- PCI master enable
mm      - memory modify (auto-incrementing)
mp	- map PCI BAR
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mw      - memory write (fill)
nand                   - NAND sub-system
nboot   - boot from NAND device
nbubt	- Burn a boot loader image on the Boot Nand Flash.
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
phyRead	- Read PCI-E Phy register
pciePhyWrite	- Write PCI-E Phy register
phyRead	- Read Phy register
phyWrite	- Write Phy register
ping	- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr	- Satrt recovery process (Distress Beacon with TFTP server)
reset   - Perform RESET of the CPU
resetenv	- Return all environment variable to default.
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
scsi    - SCSI sub-system
scsiboot- boot from SCSI device
se	- PCI Slave enable
setenv  - set environment variables
sflash	- read, write or erase the external SPI Flash.
sg	- scanning the PHYs status
sp	- Scan PCI bus.
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version
Marvell>> printenv

bootdelay=1
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
run_diag=yes
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x000a0000(param),32m@0x0(flash) 
uboot_start=0x0
uboot_size=0xa0000
env_start=0xa0000
env_size=0x10000
kernel_start=0xb0000
kernel_size=0x228000
initrd_size=0x300000
make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash);
flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_size);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000000;
bootcmd=run flash_load;
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000;
ethmtu=1500
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
uboot_ver=v1.1.1
ethact=egiga0
mfgmodel=ix4
fw_ver=v1_0_11_3114995
preroot_ver=0.1.5
serial_number=5560Y01011G20200132J0J1
ethaddr=00:D0:B8:1F:58:C3
serialNo=USC020VNA1
modelname=31962501
serialno=0,01gHe60lmsTpifmtDs0p777JY/UnBUraIBEuqC0TjmS09kxwsVBxgWFh61rzNq/8D6,USC020VNA1,
runintime=10800
ftpserver=192.168.16.4
testfile=4NC
mfgtest_state=system_tested_ok
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
initrd_start=0x2d8000
disaMvPnp=no
eth1addr=00:d0:b8:1f:58:c4
enaAutoRecovery=yes
pcieTune=no

Environment size: 1931/16380 bytes
Re: Help unbricking IOmega ix4-200d
June 20, 2017 09:04PM
This was the instruction from the thread Iomega ix4-200d U-boot needed.

Plug in the USB rootfs.

Interrupt serial console and copy/paste each line to the u-boot prompt:
setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10'
setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000'
setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset'
printenv
boot

And pls post serial console log for this.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner



Edited 1 time(s). Last edit at 06/20/2017 09:14PM by bodhi.
Re: Help unbricking IOmega ix4-200d
June 20, 2017 09:54PM
It seems to hang at the end of the posted console log below. I assume the unexpected "(" has something to do with it hanging.
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** uboot_ver:v1.1.1 **

 ** MARVELL BOARD: IX4-110 LE

U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CF600

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Found 0x20 i2c device
Toggle power status
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90)  OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp        _min=60)  OK

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:                     Z30403WL
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
[0 1 0]: Enable DMA mode (6)
  Device 1 @ 0 1:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:                     Z30404FV
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)


CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d8000

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is RGMII

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI:  AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part
scanning bus for devices...
  Device 0: (0:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
  Device 1: (1:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdpar        ts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),        $(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32        m@0x0(flash) root=LABEL=rootfs rootdelay=10'
Marvell>> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x        800000 0x1100000'
Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset'
Marvell>> printenv
bootdelay=1
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
run_diag=yes
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x0        00a0000(param),32m@0x0(flash)
uboot_start=0x0
uboot_size=0xa0000
env_start=0xa0000
env_size=0x10000
kernel_start=0xb0000
kernel_size=0x228000
initrd_size=0x300000
make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_si        ze)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_        start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash);
flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_siz        e);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000        000;
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/m        tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000;
ethmtu=1500
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
uboot_ver=v1.1.1
ethact=egiga0
mfgmodel=ix4
fw_ver=v1_0_11_3114995
preroot_ver=0.1.5
serial_number=5560Y01011G20200132J0J1
ethaddr=00:D0:B8:1F:58:C3
serialNo=USC020VNA1
modelname=31962501
serialno=0,01gHe60lmsTpifmtDs0p777JY/UnBUraIBEuqC0TjmS09kxwsVBxgWFh61rzNq/8D6,US        C020VNA1,
runintime=10800
ftpserver=192.168.16.4
testfile=4NC
mfgtest_state=system_tested_ok
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
initrd_start=0x2d8000
disaMvPnp=no
eth1addr=00:d0:b8:1f:58:c4
enaAutoRecovery=yes
pcieTune=no
usb_make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(ub        oot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(k        ernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=        LABEL=rootfs rootdelay=10
load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
usb_boot=usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000
bootcmd=run usb_make_boot_args ; run usb_boot; reset

Environment size: 2409/16380 bytes
Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
........................................................................................................

3164416 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
.................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................

7179935 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2017-06-20   3:21:37 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3164352 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes =  6.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Iomega ix4-200d
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x228000@0xb0000(zImage),0x300000@0x2d8000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 503476K/524288K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 20812K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff800000   ( 496 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07d7ef4   (8000 kB)
[    0.000000]       .init : 0xc07d8000 - 0xc0822000   ( 296 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b169c   ( 574 kB)
[    0.000000]        .bss : 0xc08b169c - 0xc08ff9d0   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000295] Console: colour dummy device 80x30
[    0.000323] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090098] pid_max: default: 32768 minimum: 301
[    0.090203] Security Framework initialized
[    0.090272] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090291] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091030] Initializing cgroup subsys io
[    0.091062] Initializing cgroup subsys devices
[    0.091086] Initializing cgroup subsys freezer
[    0.091116] Initializing cgroup subsys net_cls
[    0.091191] CPU: Testing write buffer coherency: ok
[    0.091597] Setting up static identity map for 0x8200 - 0x8258
[    0.091870] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.095310] devtmpfs: initialized
[    0.099397] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.099818] prandom: seed boundary self test passed
[    0.103618] prandom: 100 self tests passed
[    0.103651] pinctrl core: initialized pinctrl subsystem
[    0.104936] NET: Registered protocol family 16
[    0.105338] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.130097] cpuidle: using governor ladder
[    0.160095] cpuidle: using governor menu
[    0.160489] Feroceon L2: Enabling L2
[    0.160532] Feroceon L2: Cache support initialised.
[    0.160896] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.160999] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set
[    0.166011] No ATAGs?
[    0.201526] vgaarb: loaded
[    0.201883] usbcore: registered new interface driver usbfs
[    0.201963] usbcore: registered new interface driver hub
[    0.202024] usbcore: registered new device driver usb
[    0.203076] clocksource: Switched to clocksource orion_clocksource
[    0.257910] NET: Registered protocol family 2
[    0.258678] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.258740] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.258792] TCP: Hash tables configured (established 4096 bind 4096)
[    0.258854] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.258878] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.259067] NET: Registered protocol family 1
[    0.259450] RPC: Registered named UNIX socket transport module.
[    0.259462] RPC: Registered udp transport module.
[    0.259470] RPC: Registered tcp transport module.
[    0.259477] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.259745] Unpacking initramfs...
[    0.891082] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[    0.891205] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.892268] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.892341] audit: initializing netlink subsys (disabled)
[    0.892389] audit: type=2000 audit(0.880:1): initialized
[    0.892731] Initialise system trusted keyring
[    0.893150] zbud: loaded
[    0.893447] VFS: Disk quotas dquot_6.6.0
[    0.893507] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.894036] NFS: Registering the id_resolver key type
[    0.894075] Key type id_resolver registered
[    0.894084] Key type id_legacy registered
[    0.894110] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.894124] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.894350] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.894874] Key type big_key registered
[    0.914698] Key type asymmetric registered
[    0.914721] Asymmetric key parser 'x509' registered
[    0.914813] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.914834] io scheduler noop registered
[    0.914850] io scheduler deadline registered
[    0.914910] io scheduler cfq registered (default)
[    0.916234] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.916897] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
[    0.917315] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
[    0.918135] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00
[    0.918155] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    0.918169] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    0.918182] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.918569] PCI: bus0: Fast back to back transfers disabled
[    0.918595] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.919363] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.919401] PCI: bus1: Fast back to back transfers disabled
[    0.919564] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[    0.919581] pci 0000:00:01.0: BAR 13: assigned [io  0x10000-0x10fff]
[    0.919602] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff]
[    0.919621] pci 0000:01:00.0: BAR 4: assigned [io  0x10000-0x1000f]
[    0.919638] pci 0000:01:00.0: BAR 0: assigned [io  0x10010-0x10017]
[    0.919655] pci 0000:01:00.0: BAR 2: assigned [io  0x10018-0x1001f]
[    0.919672] pci 0000:01:00.0: BAR 1: assigned [io  0x10020-0x10023]
[    0.919688] pci 0000:01:00.0: BAR 3: assigned [io  0x10024-0x10027]
[    0.919704] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.919716] pci 0000:00:01.0:   bridge window [io  0x10000-0x10fff]
[    0.919731] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    0.919808] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[    0.920095] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.953770] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.954014] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.993775] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.994259] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.995711] console [ttyS0] disabled
[    0.995773] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[    1.742518] console [ttyS0] enabled
[    1.747273] nand: device found, Manufacturer ID: 0xad, Chip ID: 0x75
[    1.753691] nand: Hynix NAND 32MiB 3,3V 8-bit
[    1.758070] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16
[    1.765433] Scanning device for bad blocks
[    2.110333] 5 cmdlinepart partitions found on MTD device orion_nand
[    2.116653] Creating 5 MTD partitions on "orion_nand":
[    2.121818] 0x000000000000-0x0000000a0000 : "uboot"
[    2.128001] 0x0000000a0000-0x0000000b0000 : "env"
[    2.133988] 0x0000000b0000-0x0000002d8000 : "zImage"
[    2.140182] 0x0000002d8000-0x0000005d8000 : "initrd"
[    2.146473] 0x000000000000-0x000002000000 : "flash"
[    2.154107] libphy: Fixed MDIO Bus: probed
[    2.158571] libphy: orion_mdio_bus: probed
[    2.171671] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    3.253740] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1f:58:c3
[    4.333853] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:b8:1f:58:c4
[    4.342733] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.349351] ehci-pci: EHCI PCI platform driver
[    4.353912] ehci-orion: EHCI orion driver
[    4.358120] orion-ehci f1050000.ehci: EHCI Host Controller
[    4.363685] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    4.371531] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[    4.393110] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    4.399377] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.406223] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.413503] usb usb1: Product: EHCI Host Controller
[    4.418403] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[    4.425065] usb usb1: SerialNumber: f1050000.ehci
[    4.430486] hub 1-0:1.0: USB hub found
[    4.434338] hub 1-0:1.0: 1 port detected
[    4.439214] mousedev: PS/2 mouse device common for all mice
[    4.445175] rtc-mv f1010300.rtc: invalid RTC date, resetting to January 1st, 2013
[    4.453028] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    4.460161] i2c /dev entries driver
[    4.465205] hidraw: raw HID events driver (C) Jiri Kosina
[    4.471007] drop_monitor: Initializing network drop monitor service
[    4.477586] NET: Registered protocol family 17
[    4.482292] Key type dns_resolver registered
[    4.487431] registered taskstats version 1
[    4.491596] Loading compiled-in X.509 certificates
[    4.496497] zswap: loaded using pool lzo/zbud
[    4.509258] Key type encrypted registered
[    4.514003] rtc-mv f1010300.rtc: setting system clock to 2013-01-01 01:00:22 UTC (1357002022)
[    4.524847] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[    4.599155] systemd-udevd[84]: starting version 215
[    4.615287] random: systemd-udevd urandom read with 7 bits of entropy available
[    4.729774] SCSI subsystem initialized
[    4.753171] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    4.801714] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
[    4.817513] sata_mv f1080000.sata: slots 32 ports 2
[    4.854576] scsi host0: sata_mv
[    4.865810] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ
[    4.872810] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP
[    4.886887] scsi host1: sata_mv
[    4.890413] ata1: SATA max UDMA/133 irq 33
[    4.913265] ata2: SATA max UDMA/133 irq 33
[    4.918806] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    4.931117] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.945174] usb 1-1: Product: USB2.0 Hub
[    4.954714] hub 1-1:1.0: USB hub found
[    4.961259] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3
[    4.966907] hub 1-1:1.0: 4 ports detected
[    4.993020] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[    5.022042] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
[    5.051771] ahci 0000:01:00.0: flags: 64bit stag led slum part
[    5.065452] scsi host2: ahci
[    5.069298] scsi host3: ahci
[    5.073335] scsi host4: ahci
[    5.077218] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 84
[    5.084770] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 84
[    5.092261] ata5: DUMMY
[    5.263107] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[    5.374289] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5571
[    5.381210] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.388607] usb 1-1.3: Product: Cruzer Fit
[    5.392722] usb 1-1.3: Manufacturer: SanDisk
[    5.397034] usb 1-1.3: SerialNumber: 4C530006041215107163
[    5.412151] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[    5.418878] scsi host5: usb-storage 1-1.3:1.0
[    5.425086] usbcore: registered new interface driver usb-storage
[    5.434243] usbcore: registered new interface driver uas
[    5.443198] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    5.450155] ata3.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    5.456460] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    5.462970] ata3.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    5.474560] ata3.00: configured for UDMA/133
[    5.493155] ata1.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    5.499370] ata1.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    5.563158] ata1.00: configured for UDMA/133
[    5.583541] scsi 0:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.103183] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    6.143154] ata2.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    6.149366] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    6.213161] ata2.00: configured for UDMA/133
[    6.233525] scsi 1:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.243866] scsi 2:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.423997] scsi 5:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.00 PQ: 0 ANSI: 6
[    6.440330] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.457339] sd 2:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.466600] sd 5:0:0:0: [sdd] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB)
[    6.474946] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    6.480290] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    6.485646] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[    6.491290] sd 0:0:0:0: [sda] Write Protect is off
[    6.496574] sd 5:0:0:0: [sdd] Write Protect is off
[    6.501495] sd 1:0:0:0: [sdb] Write Protect is off
[    6.506700] sd 2:0:0:0: [sdc] Write Protect is off
[    6.511695] sd 5:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    6.520990] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.530272] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.539536] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.556826]  sdd: sdd1
[    6.564449] sd 5:0:0:0: [sdd] Attached SCSI removable disk
[    6.581936]  sdb: sdb1
[    6.584515]  sda: sda1
[    6.590420] sd 0:0:0:0: [sda] Attached SCSI disk
[    6.595220] sd 1:0:0:0: [sdb] Attached SCSI disk
[    6.603152] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    6.610283] ata4.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    6.616665] ata4.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    6.624353]  sdc: sdc1
[    6.628620] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[    6.636417] ata4.00: configured for UDMA/133
[    6.653547] scsi 3:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.663380] sd 3:0:0:0: [sde] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.671165] sd 3:0:0:0: [sde] 4096-byte physical blocks
[    6.677717] sd 3:0:0:0: [sde] Write Protect is off
[    6.682660] sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.768513]  sde: sde1
[    6.772786] sd 3:0:0:0: [sde] Attached SCSI removable disk
[    6.781455] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    6.802852] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    6.846894] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    6.871827] sd 5:0:0:0: Attached scsi generic sg3 type 0
[    6.880865] sd 3:0:0:0: Attached scsi generic sg4 type 0
printenv0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.448856] sd 1:0:0:0: [sd[   37.133159] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   37.140252] ata3.00: failed command: IDENTIFY DEVICE
[   37.145315] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 18 pio 512 in
[   37.145315]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[   37.160013] ata3.00: status: { DRDY }
[   37.163718] ata3: hard resetting link
[   37.167432] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   37.174554] ata4.00: failed command: IDENTIFY DEVICE
[   37.179560] ata4.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 18 pio 512 in
[   37.179560]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[   37.194264] ata4.00: status: { DRDY }
[   37.197950] ata4: hard resetting link
[   37.362044] random: nonblocking pool is initialized
[   37.523123] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   37.530734] ata3.00: configured for UDMA/133
[   37.538150] ata3: EH complete
[   37.543173] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   37.550783] ata4.00: configured for UDMA/133
[   37.558386] ata4: EH complete
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root device.  Common problems:
 - Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
   - Check root= (did the system wait for the right device?)
 - Missing modules (cat /proc/modules; ls /dev)
ALERT!  /dev/disk/by-label/rootfs does not exist.  Dropping to a shell!
modprobe: module i8042 not found in modules.dep
[   77.926173] uhci_hcd: USB Universal Host Controller Interface driver
[   77.942439] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   77.959425] usbcore: registered new interface driver usbhid
[   77.965201] usbhid: USB HID core driver


BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off
(initramfs) printenv0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.
63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd0:0:0: [sda] 7814037168 512-byte logic
al blocks: (4.00 TB/3.63 TiB)
/bin/sh: syntax error: unexpected "("
(initramfs) [    6.448856] sd 1:0:0:0: [sd
Re: Help unbricking IOmega ix4-200d
June 21, 2017 07:50AM
Is the USB drive 16GB?

[ 6.423997] scsi 5:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6
[ 6.440330] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 6.448856] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 6.457339] sd 2:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 6.466600] sd 5:0:0:0: [sdd] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 6.474946] sd 0:0:0:0: [sda] 4096-byte physical blocks


------

I've tweaked the instruction above a bit, pls try again:

setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash)'
setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000'
setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset'
printenv
boot

Update:

See my post below before trying to boot again with the revised envs.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner



Edited 3 time(s). Last edit at 06/21/2017 08:05AM by bodhi.
Re: Help unbricking IOmega ix4-200d
June 21, 2017 08:01AM
Derek,

I think the rootfs was not created correctly.

Please create this USB rootfs again , and this time keep the log of how you did this on Mint terminal. And post the entire log here.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Help unbricking IOmega ix4-200d
June 21, 2017 08:08AM
I could be wrong, but it sounded like the USB drive has some problems, i.e. no partition or the partition is dirty or damage, etc. Also, the ALERT! /dev/disk/by-label/rootfs does not exist. Dropping to a shell! message (quoted below) indicates this USB drive has no rootfs label (or damage).
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root device.  Common problems:
 - Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
   - Check root= (did the system wait for the right device?)
 - Missing modules (cat /proc/modules; ls /dev)
ALERT!  /dev/disk/by-label/rootfs does not exist.  Dropping to a shell!
modprobe: module i8042 not found in modules.dep
[   77.926173] uhci_hcd: USB Universal Host Controller Interface driver
[   77.942439] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   77.959425] usbcore: registered new interface driver usbhid
[   77.965201] usbhid: USB HID core driver
Re: Help unbricking IOmega ix4-200d
June 21, 2017 09:53PM
bodhi Wrote:
-------------------------------------------------------
> Derek,
>
> I think the rootfs was not created correctly.
>
> Please create this USB rootfs again , and this tim
> e keep the log of how you did this on Mint termina
> l. And post the entire log here.
mint / # cd /media/mint//d31fdf7d-ffaa-437c-982d-141f14833167/
mint d31fdf7d-ffaa-437c-982d-141f14833167 # tar -xjf /media/mint/58EE344CEE342522/Users/Derek/Downloads/Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 
mint d31fdf7d-ffaa-437c-982d-141f14833167 # vi etc/fstab
mint d31fdf7d-ffaa-437c-982d-141f14833167 # cd boot
mint boot # cp -a zImage-4.4.0-kirkwood-tld-1  zImage.fdt
mint boot # cat dts/kirkwood-iomega_ix4_200d.dtb  >> zImage.fdt
mint boot # mv uImage uImage.orig
mint boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.4.0-kirkwood-tld-1 -d zImage.fdt  uImage
Image Name:   Linux-4.4.0-kirkwood-tld-1
Created:      Thu Jun 22 01:38:37 2017
Image Type:   ARM Linux Kernel Image (uncompressed)
Data Size:    3164352 Bytes = 3090.19 kB = 3.02 MB
Load Address: 00008000
Entry Point:  00008000
mint boot # sync
Re: Help unbricking IOmega ix4-200d
June 21, 2017 10:16PM
...and finally
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** uboot_ver:v1.1.1 **

 ** MARVELL BOARD: IX4-110 LE

U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CF600

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Found 0x20 i2c device
Toggle power status
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90)  OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp                                                                                                                                                             _min=60)  OK

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:                                                                                                                                                                          Z30403WL
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
[0 1 0]: Enable DMA mode (6)
  Device 1 @ 0 1:
Model: ST4000VN000-1H4168                       Firm: SC46     Ser#:                                                                                                                                                                          Z30404FV
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)


CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d8000

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is RGMII

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI:  AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part
scanning bus for devices...
  Device 0: (0:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
  Device 1: (1:0) Vendor: ATA Prod.: ST4000VN000-1H41 Rev: SC46
            Type: Hard Disk
            Capacity: 1718295.8 MB = 1678.0 GB (3519069872 x 512)
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdpar                                                                                                                                                             ts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),                                                                                                                                                             $(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32                                                                                                                                                             m@0x0(flash) root=LABEL=rootfs rootdelay=10'
Marvell>> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x                                                                                                                                                             800000 0x1100000'
Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset'
Marvell>> printenv
bootdelay=1
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
run_diag=yes
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x0                                                                                                                                                             00a0000(param),32m@0x0(flash)
uboot_start=0x0
uboot_size=0xa0000
env_start=0xa0000
env_size=0x10000
kernel_start=0xb0000
kernel_size=0x228000
initrd_size=0x300000
make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_si                                                                                                                                                             ze)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_                                                                                                                                                             start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash);
flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_siz                                                                                                                                                             e);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000                                                                                                                                                             000;
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/m                                                                                                                                                             tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000;
ethmtu=1500
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
uboot_ver=v1.1.1
ethact=egiga0
mfgmodel=ix4
fw_ver=v1_0_11_3114995
preroot_ver=0.1.5
serial_number=5560Y01011G20200132J0J1
ethaddr=00:D0:B8:1F:58:C3
serialNo=USC020VNA1
modelname=31962501
serialno=0,01gHe60lmsTpifmtDs0p777JY/UnBUraIBEuqC0TjmS09kxwsVBxgWFh61rzNq/8D6,US                                                                                                                                                             C020VNA1,
runintime=10800
ftpserver=192.168.16.4
testfile=4NC
mfgtest_state=system_tested_ok
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
initrd_start=0x2d8000
disaMvPnp=no
eth1addr=00:d0:b8:1f:58:c4
enaAutoRecovery=yes
pcieTune=no
usb_make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(ub                                                                                                                                                             oot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(k                                                                                                                                                             ernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=                                                                                                                                                             LABEL=rootfs rootdelay=10
load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
usb_boot=usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000
bootcmd=run usb_make_boot_args ; run usb_boot; reset

Environment size: 2409/16380 bytes
Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
........................................................................................................

3164416 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
.................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................

7179935 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2017-06-22   1:38:37 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3164352 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes =  6.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Iomega ix4-200d
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x228000@0xb0000(zImage),0x300000@0x2d8000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 503476K/524288K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 20812K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff800000   ( 496 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07d7ef4   (8000 kB)
[    0.000000]       .init : 0xc07d8000 - 0xc0822000   ( 296 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b169c   ( 574 kB)
[    0.000000]        .bss : 0xc08b169c - 0xc08ff9d0   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000295] Console: colour dummy device 80x30
[    0.000323] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090098] pid_max: default: 32768 minimum: 301
[    0.090202] Security Framework initialized
[    0.090272] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090291] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091029] Initializing cgroup subsys io
[    0.091061] Initializing cgroup subsys devices
[    0.091084] Initializing cgroup subsys freezer
[    0.091115] Initializing cgroup subsys net_cls
[    0.091190] CPU: Testing write buffer coherency: ok
[    0.091596] Setting up static identity map for 0x8200 - 0x8258
[    0.091869] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.095309] devtmpfs: initialized
[    0.099383] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.099803] prandom: seed boundary self test passed
[    0.103605] prandom: 100 self tests passed
[    0.103637] pinctrl core: initialized pinctrl subsystem
[    0.104922] NET: Registered protocol family 16
[    0.105323] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.130096] cpuidle: using governor ladder
[    0.160095] cpuidle: using governor menu
[    0.160488] Feroceon L2: Enabling L2
[    0.160530] Feroceon L2: Cache support initialised.
[    0.160894] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.160998] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set
[    0.166010] No ATAGs?
[    0.201526] vgaarb: loaded
[    0.201882] usbcore: registered new interface driver usbfs
[    0.201962] usbcore: registered new interface driver hub
[    0.202024] usbcore: registered new device driver usb
[    0.203081] clocksource: Switched to clocksource orion_clocksource
[    0.257926] NET: Registered protocol family 2
[    0.258697] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.258757] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.258810] TCP: Hash tables configured (established 4096 bind 4096)
[    0.258871] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.258895] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.259082] NET: Registered protocol family 1
[    0.259465] RPC: Registered named UNIX socket transport module.
[    0.259478] RPC: Registered udp transport module.
[    0.259485] RPC: Registered tcp transport module.
[    0.259493] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.259759] Unpacking initramfs...
[    0.891083] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[    0.891208] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.892274] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.892346] audit: initializing netlink subsys (disabled)
[    0.892395] audit: type=2000 audit(0.880:1): initialized
[    0.892738] Initialise system trusted keyring
[    0.893158] zbud: loaded
[    0.893453] VFS: Disk quotas dquot_6.6.0
[    0.893513] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.894043] NFS: Registering the id_resolver key type
[    0.894088] Key type id_resolver registered
[    0.894097] Key type id_legacy registered
[    0.894123] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.894138] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.894364] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.894890] Key type big_key registered
[    0.914736] Key type asymmetric registered
[    0.914759] Asymmetric key parser 'x509' registered
[    0.914852] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.914874] io scheduler noop registered
[    0.914890] io scheduler deadline registered
[    0.914947] io scheduler cfq registered (default)
[    0.916272] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.916934] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
[    0.917349] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
[    0.918166] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00
[    0.918186] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    0.918200] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    0.918213] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.918597] PCI: bus0: Fast back to back transfers disabled
[    0.918623] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.919394] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.919432] PCI: bus1: Fast back to back transfers disabled
[    0.919597] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[    0.919614] pci 0000:00:01.0: BAR 13: assigned [io  0x10000-0x10fff]
[    0.919635] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff]
[    0.919653] pci 0000:01:00.0: BAR 4: assigned [io  0x10000-0x1000f]
[    0.919670] pci 0000:01:00.0: BAR 0: assigned [io  0x10010-0x10017]
[    0.919687] pci 0000:01:00.0: BAR 2: assigned [io  0x10018-0x1001f]
[    0.919704] pci 0000:01:00.0: BAR 1: assigned [io  0x10020-0x10023]
[    0.919721] pci 0000:01:00.0: BAR 3: assigned [io  0x10024-0x10027]
[    0.919736] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.919749] pci 0000:00:01.0:   bridge window [io  0x10000-0x10fff]
[    0.919764] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    0.919841] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[    0.920128] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.953774] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.954018] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.993779] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.994262] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.995707] console [ttyS0] disabled
[    0.995769] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[    1.742489] console [ttyS0] enabled
[    1.747243] nand: device found, Manufacturer ID: 0xad, Chip ID: 0x75
[    1.753662] nand: Hynix NAND 32MiB 3,3V 8-bit
[    1.758041] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16
[    1.765406] Scanning device for bad blocks
[    2.110275] 5 cmdlinepart partitions found on MTD device orion_nand
[    2.116591] Creating 5 MTD partitions on "orion_nand":
[    2.121755] 0x000000000000-0x0000000a0000 : "uboot"
[    2.127946] 0x0000000a0000-0x0000000b0000 : "env"
[    2.133928] 0x0000000b0000-0x0000002d8000 : "zImage"
[    2.140122] 0x0000002d8000-0x0000005d8000 : "initrd"
[    2.146409] 0x000000000000-0x000002000000 : "flash"
[    2.154040] libphy: Fixed MDIO Bus: probed
[    2.158500] libphy: orion_mdio_bus: probed
[    2.171581] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    3.253743] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1f:58:c3
[    4.333853] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:b8:1f:58:c4
[    4.342731] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.349350] ehci-pci: EHCI PCI platform driver
[    4.353910] ehci-orion: EHCI orion driver
[    4.358119] orion-ehci f1050000.ehci: EHCI Host Controller
[    4.363693] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    4.371638] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[    4.393115] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    4.399385] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.406238] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.413509] usb usb1: Product: EHCI Host Controller
[    4.418409] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[    4.425072] usb usb1: SerialNumber: f1050000.ehci
[    4.430491] hub 1-0:1.0: USB hub found
[    4.434345] hub 1-0:1.0: 1 port detected
[    4.439222] mousedev: PS/2 mouse device common for all mice
[    4.445507] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    4.452581] i2c /dev entries driver
[    4.457644] hidraw: raw HID events driver (C) Jiri Kosina
[    4.463512] drop_monitor: Initializing network drop monitor service
[    4.470057] NET: Registered protocol family 17
[    4.474805] Key type dns_resolver registered
[    4.479912] registered taskstats version 1
[    4.484112] Loading compiled-in X.509 certificates
[    4.488980] zswap: loaded using pool lzo/zbud
[    4.501657] Key type encrypted registered
[    4.506408] rtc-mv f1010300.rtc: setting system clock to 2013-01-02 01:21:15 UTC (1357089675)
[    4.517237] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[    4.591339] systemd-udevd[84]: starting version 215
[    4.605216] random: systemd-udevd urandom read with 7 bits of entropy available
[    4.748809] SCSI subsystem initialized
[    4.753199] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    4.806613] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
[    4.819575] sata_mv f1080000.sata: slots 32 ports 2
[    4.860840] scsi host0: sata_mv
[    4.871817] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ
[    4.882860] scsi host1: sata_mv
[    4.894137] ata1: SATA max UDMA/133 irq 33
[    4.898263] ata2: SATA max UDMA/133 irq 33
[    4.914913] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    4.921671] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.929455] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP
[    4.941441] usb 1-1: Product: USB2.0 Hub
[    4.951050] hub 1-1:1.0: USB hub found
[    4.959294] hub 1-1:1.0: 4 ports detected
[    4.976147] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3
[    4.981777] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[    5.030093] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
[    5.051360] ahci 0000:01:00.0: flags: 64bit stag led slum part
[    5.061749] scsi host2: ahci
[    5.065988] scsi host3: ahci
[    5.069934] scsi host4: ahci
[    5.073726] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 84
[    5.081196] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 84
[    5.088677] ata5: DUMMY
[    5.243176] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
[    5.354402] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5571
[    5.361325] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.368707] usb 1-1.2: Product: Cruzer Fit
[    5.372822] usb 1-1.2: Manufacturer: SanDisk
[    5.377149] usb 1-1.2: SerialNumber: 4C530006041215107163
[    5.392242] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    5.398988] scsi host5: usb-storage 1-1.2:1.0
[    5.403446] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    5.411643] usbcore: registered new interface driver usb-storage
[    5.420742] usbcore: registered new interface driver uas
[    5.433204] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    5.440181] ata3.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    5.446536] ata1.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    5.452751] ata1.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    5.459601] ata3.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    5.467230] ata3.00: configured for UDMA/133
[    5.523162] ata1.00: configured for UDMA/133
[    5.543547] scsi 0:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.063190] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    6.103154] ata2.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    6.109366] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    6.173160] ata2.00: configured for UDMA/133
[    6.193518] scsi 1:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.203831] scsi 2:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.404099] scsi 5:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.00 PQ: 0 ANSI: 6
[    6.420344] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.428868] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.437347] sd 2:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.446710] sd 5:0:0:0: [sdd] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB)
[    6.454976] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    6.460320] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    6.465669] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[    6.471317] sd 0:0:0:0: [sda] Write Protect is off
[    6.476587] sd 1:0:0:0: [sdb] Write Protect is off
[    6.481466] sd 5:0:0:0: [sdd] Write Protect is off
[    6.486552] sd 2:0:0:0: [sdc] Write Protect is off
[    6.491672] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.501049] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.510243] sd 5:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    6.519535] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.536686]  sdd: sdd1
[    6.544679] sd 5:0:0:0: [sdd] Attached SCSI removable disk
[    6.560653]  sda: sda1
[    6.563148] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    6.569572]  sdb: sdb1
[    6.576295] sd 1:0:0:0: [sdb] Attached SCSI disk
[    6.581073] sd 0:0:0:0: [sda] Attached SCSI disk
[    6.586534] ata4.00: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[    6.592912] ata4.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    6.602741]  sdc: sdc1
[    6.607063] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[    6.613965] ata4.00: configured for UDMA/133
[    6.633546] scsi 3:0:0:0: Direct-Access     ATA      ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[    6.643375] sd 3:0:0:0: [sde] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    6.651159] sd 3:0:0:0: [sde] 4096-byte physical blocks
[    6.657706] sd 3:0:0:0: [sde] Write Protect is off
[    6.662653] sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.736109]  sde: sde1
[    6.740366] sd 3:0:0:0: [sde] Attached SCSI removable disk
[    6.749058] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    6.770496] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    6.816874] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    6.839330] sd 5:0:0:0: Attached scsi generic sg3 type 0
[    6.852571] sd 3:0:0:0: Attached scsi generic sg4 type 0
[   29.238179] random: nonblocking pool is initialized
[   37.133156] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   37.140249] ata3.00: failed command: IDENTIFY DEVICE
[   37.145281] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 18 pio 512 in
[   37.145281]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[   37.159970] ata3.00: status: { DRDY }
[   37.163670] ata3: hard resetting link
[   37.513125] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   37.520736] ata3.00: configured for UDMA/133
[   37.528133] ata3: EH complete
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
modprobe: module ext3 not found in modules.dep
Begin: Checking root file system ... fsck from util-linux 2.25.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sdd1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[   52.823236] EXT4-fs (sdd1): mounting ext3 file system using the ext4 subsystem
[   52.840695] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   54.141083] systemd-udevd[318]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[   54.469930] __nand_correct_data: uncorrectable ECC error
[ ok                                             done.
[....] Waiting for /dev to be fully populated...[   54.583585] __nand_correct_data: uncorrectable ECC error
[   54.626738] __nand_correct_data: uncorrectable ECC error
[   54.632385] __nand_correct_data: uncorrectable ECC error
[   54.655875] __nand_correct_data: uncorrectable ECC error
[   54.661389] __nand_correct_data: uncorrectable ECC error
[   54.703210] __nand_correct_data: uncorrectable ECC error
[   54.708692] __nand_correct_data: uncorrectable ECC error
[   54.744483] __nand_correct_data: uncorrectable ECC error
[   54.801293] adt7475 0-002e: ADT7473 device, revision 0
[   54.827783] adt7475 0-002e: Optional features: fan4 pwm2
[   54.848235] orion_wdt: Initial timeout 21 sec
[   54.890241] marvell-cesa: probe of f1030000.crypto failed with error -524
[   85.133169] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   85.140259] ata4.00: failed command: IDENTIFY DEVICE
[   85.145309] ata4.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 24 pio 512 in
[   85.145309]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[   85.159999] ata4.00: status: { DRDY }
[   85.163699] ata4: hard resetting link
[   85.167413] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   85.174535] ata3.00: failed command: IDENTIFY DEVICE
[   85.179533] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 20 pio 512 in
[   85.179533]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[   85.194240] ata3.00: status: { DRDY }
[   85.197922] ata3: hard resetting link
[   85.523131] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   85.530760] ata4.00: configured for UDMA/133
[   85.538154] ata4: EH complete
[   85.543180] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   85.550812] ata3.00: configured for UDMA/133
[   85.558386] ata3: EH complete
done.
[ ok ] Activating swap...done.
[   86.207116] EXT4-fs (sdd1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: Superblock last mount time (Wed Jun 21 18:49:08 2017,
        now = Tue Jan  1 17:22:37 2013) is in the future.
FIXED.
rootfs: Superblock last write time (Wed Jun 21 18:52:32 2017,
        now = Tue Jan  1 17:22:37 2013) is in the future.
FIXED.
rootfs: 14516/977280 files (6.5% non-contiguous), 202495/3907580 blocks
done.
[   98.156870] EXT4-fs (sdd1): re-mounted. Opts: errors=remount-ro
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[  100.458127] NET: Registered protocol family 10
[  101.616796] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:1f:58:c3
Sending on   LPF/eth0/00:d0:b8:1f:58:c3
Sending on   Socket/fallback
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15
No DHCPOFFERS received.
Trying recorded lease 192.168.0.16
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.

--- 192.168.0.1 ping statistics ---
1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms

bound: renewal in 98851602 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1258 (syslogd)
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NTP server: ntpd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1261 (klogd)
. ok

Debian GNU/Linux 8 debian ttyS0

debian login:
Re: Help unbricking IOmega ix4-200d
June 21, 2017 11:21PM
Re: Help unbricking IOmega ix4-200d
June 22, 2017 08:11PM
Thanks!

However, now after rebooting, it goes back to the Marvell prompt. Also, what is uboot and should it be updated?
Re: Help unbricking IOmega ix4-200d
June 22, 2017 08:27PM
Derek,


What you did with these commands were to set necessary u-boot envs temporarily for bootting. Once it is working like now, you need to save them. The bold line is the command to save envs.

setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash)'
setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000'
setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset'
saveenv
printenv
boot

So go ahead and power up, interrupt serial console and execute each command. Afer this, it will be persistent.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Help unbricking IOmega ix4-200d
June 24, 2017 01:28AM
Got it, it's persistant now, thank you. Any good references on installing OpenMediaVault?
Re: Help unbricking IOmega ix4-200d
June 24, 2017 03:39AM
Red9r Wrote:
-------------------------------------------------------
> Got it, it's persistant now, thank you. Any good r
> eferences on installing OpenMediaVault?

See the Wiki thread:
http://forum.doozan.com/read.php?2,23630


Quote

Media Streaming

OpenMediaVault
Streaming music from Kirkwood plugs to IOS devices via WiFi
Create Your Own In-Home Radio Station Using a Pogoplug Mobile
Install Logitech Media Server on Debian wheezy
Install Logitech Media Server on Debian jessie
Install Logitech Media Server with nightly build (WIP)
Plex media server on PogoPlug
Airplay on a Pogoplug

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: