cant update rescue system July 16, 2014 06:41AM |
Registered: 9 years ago Posts: 4 |
[ 20.344130] UBI error: ubi_read_volume_table: the layout volume was not found [ 20.351404] UBI error: ubi_init: cannot attach mtd2 ... [ 20.601944] VFS: Cannot open root device "ubi0:mtdblock2" or unknown-block(0,0) [ 20.609297] Please append a correct "root=" boot option; here are the available partitions: [ 20.617706] 1f00 1024 mtdblock0 (driver?) [ 20.622785] 1f01 4096 mtdblock1 (driver?) [ 20.627879] 1f02 32768 mtdblock2 (driver?) [ 20.632961] 1f03 224256 mtdblock3 (driver?) [ 20.638054] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
nand erase 0x100000 0x400000 tftp 0x800000 uImage-mtd1.img nand write.e 0x800000 0x100000 0x380000 tftp 0x1000000 rootfs-mtd2.img setenv rescue_set_bootargs 'setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params' setenv rescue_bootcmd 'if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi' setenv bootcmd 'run usb_bootcmd; usb stop; run rescue_bootcmd; reset' saveenv run rescue_bootcmd
u b i p a r t u - b o o t UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI error: ubi_io_read: error -74 while reading 64 bytes from PEB 5:0, read 64 bytes UBI error: ubi_io_read: error -74 while reading 512 bytes from PEB 5:512, read 512 bytes UBI error: ubi_io_read: error -74 while reading 512 bytes from PEB 7:512, read 512 bytes UBI error: ubi_read_volume_table: the layout volume was not found UBI error: ubi_init: cannot attach mtd1 UBI error: ubi_init: UBI error: cannot initialize UBI, error -22 UBI init error 22 DockStar> ubi part rootfs u b i p a r t r o o t f s UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI error: ubi_read_volume_table: the layout volume was not found UBI error: ubi_init: cannot attach mtd1 UBI error: ubi_init: UBI error: cannot initialize UBI, error -22 UBI init error 22
DockStar> printenv p r i n t e n v arcNumber=2998 baudrate=115200 bootargs=console=ttyS0,115200 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) bootcmd=run usb_bootcmd; usb stop; run rescue_bootcmd; reset bootcmd_pogo=run bootcmd_rescue bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000 bootdelay=10 console=ttyS0,115200 ethact=egiga0 ethaddr=00:10:75:1A:D2:81 fileaddr=1000000 filesize=1b60000 force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi if_netconsole=ping $serverip ipaddr=192.168.178.100 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtddevname=rootfs mtddevnum=2 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) ncip=192.168.178.33 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi preboot=run if_netconsole start_netconsole rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=1 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:mtdblock2 ro rootfstype=ubifs $mtdparts $rescue_custom_params serverip=192.168.178.33 set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts init=$ubifs_init $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi; usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot; usb_device=0:1 usb_init=usb start; if ext2load usb 0:1 0x800000 /boot/uImage 1; then setenv usb_device 0:1; setenv usb_root /dev/sda1; elif ext2load usb 1:1 0x800000 /boot/uImage 1; then setenv usb_device 1:1; setenv usb_root /dev/sdb1; elif ext2load usb 2:1 0x800000 /boot/uImage 1; then setenv usb_device 2:1; setenv usb_root /dev/sdc1; elif ext2load usb 3:1 0x800000 /boot/uImage 1; then setenv usb_device 3:1;setenv usb_root /dev/sdd1; fi; usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext2 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params Environment size: 2993/131068 bytes
U-Boot 2014.01-tld-1 (Mar 17 2014 - 22:04:15) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Using egiga0 device host 192.168.178.33 is alive
DockStar> run rescue_bootcmd r u n r e s c u e _ b o o t c m d NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Created: 2012-10-29 22:52:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Starting kernel ...
Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.3.2-kirkwide (davygravy@bitbaker64) (gcc version 4.3.5 (Buildroot 2010.08) ) #1 Mon Oct 29 17:52:07 CDT 2012 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Seagate FreeAgent DockStar [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=2 root=ubi0:mtdblock2 ro rootfstype=ubifs mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 122080k/122080k available, 8992k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc06c06c8 (6882 kB) [ 0.000000] .init : 0xc06c1000 - 0xc06eb000 ( 168 kB) [ 0.000000] .data : 0xc06ec000 - 0xc0734c38 ( 292 kB) [ 0.000000] .bss : 0xc0734c5c - 0xc07a4294 ( 446 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:114 [ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: orion_gpio0 [ 0.000000] gpiochip_add: registered GPIOs 32 to 49 on device: orion_gpio1 [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms [ 0.000000] Console: colour dummy device 80x30 [ 19.243166] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 19.333091] pid_max: default: 32768 minimum: 301 [ 19.333216] Security Framework initialized [ 19.333236] SELinux: Disabled at boot. [ 19.333299] Mount-cache hash table entries: 512 [ 19.333667] Initializing cgroup subsys cpuacct [ 19.333682] Initializing cgroup subsys devices [ 19.333694] Initializing cgroup subsys freezer [ 19.333702] Initializing cgroup subsys net_cls [ 19.333772] CPU: Testing write buffer coherency: ok [ 19.334050] Setting up static identity map for 0x511040 - 0x51107c [ 19.335061] devtmpfs: initialized [ 19.336932] NET: Registered protocol family 16 [ 19.337677] Kirkwood: MV88F6281-A0, TCLK=200000000. [ 19.337693] Feroceon L2: Enabling L2 [ 19.337730] Feroceon L2: Cache support initialised. [ 19.342055] bio: create slab <bio-0> at 0 [ 19.342402] vgaarb: loaded [ 19.342679] SCSI subsystem initialized [ 19.343015] usbcore: registered new interface driver usbfs [ 19.343110] usbcore: registered new interface driver hub [ 19.343205] usbcore: registered new device driver usb [ 19.343782] Switching to clocksource orion_clocksource [ 19.368887] NET: Registered protocol family 2 [ 19.369117] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 19.369700] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 19.369800] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 19.369854] TCP: Hash tables configured (established 4096 bind 4096) [ 19.369864] TCP reno registered [ 19.369874] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 19.369897] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 19.370126] NET: Registered protocol family 1 [ 19.370442] RPC: Registered named UNIX socket transport module. [ 19.370453] RPC: Registered udp transport module. [ 19.370461] RPC: Registered tcp transport module. [ 19.370468] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 19.370534] NetWinder Floating Point Emulator V0.97 (double precision) [ 19.371087] audit: initializing netlink socket (disabled) [ 19.371122] type=2000 audit(0.120:1): initialized [ 19.379665] VFS: Disk quotas dquot_6.5.2 [ 19.379905] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 19.382589] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 19.383706] JFFS2 version 2.2. (NAND) (SUMMARY) \0xc2\0xa9 2001-2006 Red Hat, Inc. [ 19.384285] fuse init (API version 7.18) [ 19.384757] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 19.386140] msgmni has been set to 238 [ 19.387410] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 19.387424] io scheduler noop registered [ 19.387431] io scheduler deadline registered [ 19.387467] io scheduler cfq registered (default) [ 19.387526] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver [ 19.387562] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver [ 19.423885] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 19.463863] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) [ 19.503853] mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) [ 19.543853] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) [ 19.544190] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 19.564715] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 20.058742] console [ttyS0] enabled [ 20.063329] ONFI flash detected [ 20.066604] ONFI param page 0 valid [ 20.070114] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD) [ 20.077828] Scanning device for bad blocks [ 20.234281] 4 cmdlinepart partitions found on MTD device orion_nand [ 20.240576] Creating 4 MTD partitions on "orion_nand": [ 20.245755] 0x000000000000-0x000000100000 : "u-boot" [ 20.251591] 0x000000100000-0x000000500000 : "uImage" [ 20.257410] 0x000000500000-0x000002500000 : "rootfs" [ 20.263121] 0x000002500000-0x000010000000 : "data" [ 20.269005] UBI: attaching mtd2 to ubi0 [ 20.272861] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 20.279174] UBI: logical eraseblock size: 129024 bytes [ 20.284605] UBI: smallest flash I/O unit: 2048 [ 20.289327] UBI: sub-page size: 512 [ 20.293969] UBI: VID header offset: 512 (aligned 512) [ 20.299827] UBI: data offset: 2048 [ 20.339653] UBI: max. sequence number: 0 [ 20.344130] UBI error: ubi_read_volume_table: the layout volume was not found [ 20.351404] UBI error: ubi_init: cannot attach mtd2 [ 20.356487] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 20.363382] mv643xx_eth smi: probed [ 20.369005] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:10:75:1a:d2:81 [ 20.377894] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 20.384509] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 20.389837] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 20.423840] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 20.443822] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 20.449835] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 20.456673] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 20.463940] usb usb1: Product: Marvell Orion EHCI [ 20.468664] usb usb1: Manufacturer: Linux 3.3.2-kirkwide ehci_hcd [ 20.474795] usb usb1: SerialNumber: orion-ehci.0 [ 20.479887] hub 1-0:1.0: USB hub found [ 20.483666] hub 1-0:1.0: 1 port detected [ 20.487909] Initializing USB Mass Storage driver... [ 20.492898] usbcore: registered new interface driver usb-storage [ 20.498947] USB Mass Storage support registered. [ 20.503867] mousedev: PS/2 mouse device common for all mice [ 20.509515] i2c /dev entries driver [ 20.513476] device-mapper: uevent: version 1.0.3 [ 20.518469] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com [ 20.527030] cpuidle: using governor ladder [ 20.531218] cpuidle: using governor menu [ 20.536397] TCP cubic registered [ 20.539638] NET: Registered protocol family 17 [ 20.544160] Registering the dns_resolver key type [ 20.549315] registered taskstats version 1 [ 20.554122] console [netcon0] enabled [ 20.557800] netconsole: network logging started [ 20.562353] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 20.568719] Initializing network drop monitor service [ 20.574022] md: Waiting for all devices to be available before autodetect [ 20.580838] md: If you don't use raid, use raid=noautodetect [ 20.587164] md: Autodetecting RAID arrays. [ 20.591277] md: Scanned 0 and added 0 devices. [ 20.595760] md: autorun ... [ 20.598565] md: ... autorun DONE. [ 20.601944] VFS: Cannot open root device "ubi0:mtdblock2" or unknown-block(0,0) [ 20.609297] Please append a correct "root=" boot option; here are the available partitions: [ 20.617706] 1f00 1024 mtdblock0 (driver?) [ 20.622785] 1f01 4096 mtdblock1 (driver?) [ 20.627879] 1f02 32768 mtdblock2 (driver?) [ 20.632961] 1f03 224256 mtdblock3 (driver?) [ 20.638054] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 18.375563] VFS: Cannot open root device "sda1" or unknown-block(0,0) [ 18.382036] Please append a correct "root=" boot option; here are the available partitions: [ 18.390452] 1f00 1024 mtdblock0 (driver?) [ 18.395552] 1f01 4096 mtdblock1 (driver?) [ 18.400639] 1f02 32768 mtdblock2 (driver?) [ 18.405733] 1f03 224256 mtdblock3 (driver?) [ 18.410814] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 18.419153] [<c001369c>] (unwind_backtrace+0x0/0xe0) from [<c02c6100>] (panic+0x50/0x194) [ 18.427393] [<c02c6100>] (panic+0x50/0x194) from [<c03e6c08>] (mount_block_root+0x234/0x284) [ 18.435886] [<c03e6c08>] (mount_block_root+0x234/0x284) from [<c03e6de0>] (prepare_namespace+0x124/0x184) [ 18.445512] [<c03e6de0>] (prepare_namespace+0x124/0x184) from [<c03e689c>] (kernel_init+0x12c/0x160) [ 18.454696] [<c03e689c>] (kernel_init+0x12c/0x160) from [<c000ee18>] (kernel_thread_exit+0x0/0x8)
Re: cant update rescue system July 16, 2014 02:00PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: cant update rescue system July 17, 2014 07:20AM |
Registered: 9 years ago Posts: 4 |
Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.14.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Apr 1 22:54:58 PDT 2014 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Seagate FreeAgent DockStar [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 122460K/131072K available (4779K kernel code, 352K rwdata, 1644K rodata, 213K init, 424K bss, 8612K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc064df14 (6424 kB) [ 0.000000] .init : 0xc064e000 - 0xc0683444 ( 214 kB) [ 0.000000] .data : 0xc0684000 - 0xc06dc3c4 ( 353 kB) [ 0.000000] .bss : 0xc06dc3c4 - 0xc074665c ( 425 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns [ 5.436425] Console: colour dummy device 80x30 [ 5.436455] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 5.526202] pid_max: default: 32768 minimum: 301 [ 5.526309] Security Framework initialized [ 5.526374] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 5.526393] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 5.526980] Initializing cgroup subsys devices [ 5.527005] Initializing cgroup subsys freezer [ 5.527019] Initializing cgroup subsys net_cls [ 5.527029] Initializing cgroup subsys blkio [ 5.527104] CPU: Testing write buffer coherency: ok [ 5.527494] Setting up static identity map for 0x485fa0 - 0x485fdc [ 5.529603] devtmpfs: initialized [ 5.532215] prandom: seed boundary self test passed [ 5.536315] prandom: 100 self tests passed [ 5.536331] pinctrl core: initialized pinctrl subsystem [ 5.536706] regulator-dummy: no parameters [ 5.537043] NET: Registered protocol family 16 [ 5.537473] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 5.538257] cpuidle: using governor ladder [ 5.538274] cpuidle: using governor menu [ 5.538388] Kirkwood: MV88F6281-A0, TCLK=200000000. [ 5.538409] Feroceon L2: Enabling L2 [ 5.538447] Feroceon L2: Cache support initialised. [ 5.543659] bio: create slab <bio-0> at 0 [ 5.544109] vgaarb: loaded [ 5.544409] usbcore: registered new interface driver usbfs [ 5.544476] usbcore: registered new interface driver hub [ 5.544603] usbcore: registered new device driver usb [ 5.545334] Switched to clocksource orion_clocksource [ 5.570078] NET: Registered protocol family 2 [ 5.570730] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 5.570755] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 5.570775] TCP: Hash tables configured (established 1024 bind 1024) [ 5.570845] TCP: reno registered [ 5.570861] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 5.570883] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 5.571077] NET: Registered protocol family 1 [ 5.571398] RPC: Registered named UNIX socket transport module. [ 5.571409] RPC: Registered udp transport module. [ 5.571416] RPC: Registered tcp transport module. [ 5.571423] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.571771] NetWinder Floating Point Emulator V0.97 (double precision) [ 5.572296] futex hash table entries: 256 (order: -1, 3072 bytes) [ 5.572445] audit: initializing netlink subsys (disabled) [ 5.572494] audit: type=2000 audit(0.120:1): initialized [ 5.573144] bounce pool size: 64 pages [ 5.573215] zbud: loaded [ 5.573405] VFS: Disk quotas dquot_6.5.2 [ 5.573458] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.573742] NFS: Registering the id_resolver key type [ 5.573796] Key type id_resolver registered [ 5.573806] Key type id_legacy registered [ 5.573823] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 5.573833] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 5.573985] jffs2: version 2.2. (NAND) (SUMMARY) \0xc2\0xa9 2001-2006 Red Hat, Inc. [ 5.574263] msgmni has been set to 239 [ 5.574379] Key type big_key registered [ 5.576227] alg: No test for stdrng (krng) [ 5.576317] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 5.576329] io scheduler noop registered [ 5.576336] io scheduler deadline registered [ 5.576368] io scheduler cfq registered (default) [ 5.576625] mv_xor mv_xor.0: Marvell shared XOR driver [ 5.615423] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 5.655391] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 5.655513] mv_xor mv_xor.1: Marvell shared XOR driver [ 5.695398] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 5.735396] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 5.735690] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.756350] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A [ 6.294870] console [ttyS0] enabled [ 6.299463] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 6.305871] nand: Micron MT29F2G08AAD [ 6.309552] nand: 256MiB, SLC, page size: 2048, OOB size: 64 [ 6.315242] Scanning device for bad blocks [ 6.534915] 4 cmdlinepart partitions found on MTD device orion_nand [ 6.541223] Creating 4 MTD partitions on "orion_nand": [ 6.546406] 0x000000000000-0x000000100000 : "u-boot" [ 6.551679] 0x000000100000-0x000000500000 : "uImage" [ 6.556970] 0x000000500000-0x000002500000 : "rootfs" [ 6.562247] 0x000002500000-0x000010000000 : "data" [ 6.568146] libphy: Fixed MDIO Bus: probed [ 6.578381] libphy: orion_mdio_bus: probed [ 6.582575] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.666126] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:10:75:1a:d2:81 [ 7.675063] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.681643] ehci-pci: EHCI PCI platform driver [ 7.686178] ehci-orion: EHCI orion driver [ 7.690270] orion-ehci orion-ehci.0: EHCI Host Controller [ 7.695734] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 7.703449] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 7.725369] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 7.731482] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.738319] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.745586] usb usb1: Product: EHCI Host Controller [ 7.750490] usb usb1: Manufacturer: Linux 3.14.0-kirkwood-tld-1 ehci_hcd [ 7.757235] usb usb1: SerialNumber: orion-ehci.0 [ 7.762424] hub 1-0:1.0: USB hub found [ 7.766253] hub 1-0:1.0: 1 port detected [ 7.770739] mousedev: PS/2 mouse device common for all mice [ 8.085389] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.236838] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 8.243582] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.250774] usb 1-1: Product: USB2.0 Hub [ 8.255483] hub 1-1:1.0: USB hub found [ 8.259585] hub 1-1:1.0: 4 ports detected [ 8.545714] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 8.661962] usb 1-1.2: New USB device found, idVendor=1307, idProduct=0165 [ 8.668895] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.676267] usb 1-1.2: Product: USB Mass Storage Device [ 8.681515] usb 1-1.2: Manufacturer: USBest Technology [ 8.686694] usb 1-1.2: SerialNumber: 100202500155a8 [ 8.785361] rtc-mv rtc-mv: internal RTC not ticking [ 8.790367] i2c /dev entries driver [ 8.794487] hidraw: raw HID events driver (C) Jiri Kosina [ 8.800227] drop_monitor: Initializing network drop monitor service [ 8.806735] TCP: cubic registered [ 8.810065] NET: Registered protocol family 17 [ 8.814649] Key type dns_resolver registered [ 8.819435] registered taskstats version 1 [ 8.824067] regulator-dummy: incomplete constraints, leaving on [ 8.830361] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 8.837718] Waiting 10 sec before mounting root device... [ 18.845750] VFS: Cannot open root device "sda1" or unknown-block(0,0): error -19 [ 18.853184] Please append a correct "root=" boot option; here are the available partitions: [ 18.861614] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 18.869922] CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.0-kirkwood-tld-1 #1 [ 18.877028] [<c00142fc>] (unwind_backtrace) from [<c0010e78>] (show_stack+0x10/0x14) [ 18.884817] [<c0010e78>] (show_stack) from [<c047e8c8>] (panic+0x80/0x1e4) [ 18.891729] [<c047e8c8>] (panic) from [<c064f018>] (mount_block_root+0x1fc/0x240) [ 18.899250] [<c064f018>] (mount_block_root) from [<c064f140>] (mount_root+0xe4/0x10c) [ 18.907115] [<c064f140>] (mount_root) from [<c064f28c>] (prepare_namespace+0x124/0x184) [ 18.915155] [<c064f28c>] (prepare_namespace) from [<c064ec48>] (kernel_init_freeable+0x1f8/0x240) [ 18.924067] [<c064ec48>] (kernel_init_freeable) from [<c047cb48>] (kernel_init+0x8/0xe4) [ 18.932195] [<c047cb48>] (kernel_init) from [<c000e050>] (ret_from_fork+0x14/0x24)
Re: cant update rescue system July 17, 2014 09:29AM |
Admin Registered: 13 years ago Posts: 18,495 |
setenv usb_rootfstype bootThis will only temporarily remove this env. If it boots OK, you can set it for real in Debian with fw_setenv.
Re: cant update rescue system July 17, 2014 11:20AM |
Registered: 9 years ago Posts: 4 |
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[ 3.421731] Waiting 10 sec before mounting root device... [ 13.429503] List of all partitions: [ 13.433011] No filesystem could mount root, tried: [ 13.437924] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 13.446224] CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.0-kirkwood-tld-1 #1 [ 13.453331] [<c00142fc>] (unwind_backtrace) from [<c0010e78>] (show_stack+0x10/0x14) [ 13.461121] [<c0010e78>] (show_stack) from [<c047e8c8>] (panic+0x80/0x1e4) [ 13.468033] [<c047e8c8>] (panic) from [<c064f018>] (mount_block_root+0x1fc/0x240) [ 13.475553] [<c064f018>] (mount_block_root) from [<c064f140>] (mount_root+0xe4/0x10c) [ 13.483418] [<c064f140>] (mount_root) from [<c064f28c>] (prepare_namespace+0x124/0x184) [ 13.491458] [<c064f28c>] (prepare_namespace) from [<c064ec48>] (kernel_init_freeable+0x1f8/0x240) [ 13.500370] [<c064ec48>] (kernel_init_freeable) from [<c047cb48>] (kernel_init+0x8/0xe4) [ 13.508498] [<c047cb48>] (kernel_init) from [<c000e050>] (ret_from_fork+0x14/0x24)
Re: cant update rescue system July 17, 2014 02:15PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: cant update rescue system July 17, 2014 05:02PM |
Registered: 9 years ago Posts: 4 |
USERNAME@PCNAME:~$ md5sum /home/USERNAME/Desktop/Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 3c55093a67ea6166b31c9d111d896727 Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 USERNAME@PCNAME:~$ sudo fdisk /dev/sdl Befehl (m für Hilfe): p Platte /dev/sdl: 3898 MByte, 3898142208 Byte 120 Köpfe, 62 Sektoren/Spur, 1023 Zylinder, zusammen 7613559 Sektoren Einheiten = Sektoren von 1 × 512 = 512 Bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Festplattenidentifikation: 0x006a21b4 Gerät boot. Anfang Ende Blöcke Id System Befehl (m für Hilfe): n Partition type: p primary (0 primary, 0 extended, 4 free) e extended Select (default p): p Partitionsnummer (1-4, Vorgabe: 1): 1 Erster Sektor (2048-7613558, Vorgabe: 2048): Benutze den Standardwert 2048 Last Sektor, +Sektoren or +size{K,M,G} (2048-7613558, Vorgabe: 7613558): +3500M Befehl (m für Hilfe): n Partition type: p primary (1 primary, 0 extended, 3 free) e extended Select (default p): p Partitionsnummer (1-4, Vorgabe: 2): 2 Erster Sektor (7170048-7613558, Vorgabe: 7170048): Benutze den Standardwert 7170048 Last Sektor, +Sektoren or +size{K,M,G} (7170048-7613558, Vorgabe: 7613558): Benutze den Standardwert 7613558 Befehl (m für Hilfe): a Partitionsnummer (1-4): 1 Befehl (m für Hilfe): t Partitionsnummer (1-4): 1 Hex code (L um eine Liste anzuzeigen): 83 Befehl (m für Hilfe): t Partitionsnummer (1-4): 2 Hex code (L um eine Liste anzuzeigen): 82 Der Dateisystemtyp der Partition 2 ist nun 82 (Linux Swap / Solaris) Befehl (m für Hilfe): p Platte /dev/sdl: 3898 MByte, 3898142208 Byte 120 Köpfe, 62 Sektoren/Spur, 1023 Zylinder, zusammen 7613559 Sektoren Einheiten = Sektoren von 1 × 512 = 512 Bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Festplattenidentifikation: 0x006a21b4 Gerät boot. Anfang Ende Blöcke Id System /dev/sdl1 * 2048 7170047 3584000 83 Linux /dev/sdl2 7170048 7613558 221755+ 82 Linux Swap / Solaris Befehl (m für Hilfe): w Die Partitionstabelle wurde verändert! Rufe ioctl() um Partitionstabelle neu einzulesen. Synchronisiere Platten. USERNAME@PCNAME:~$ sudo mkfs.ext3 -L rootfs /dev/sdl1 mke2fs 1.42.9 (4-Feb-2014) Dateisystem-Label=rootfs OS-Typ: Linux Blockgröße=4096 (log=2) Fragmentgröße=4096 (log=2) Stride=0 Blöcke, Stripebreite=0 Blöcke 224000 Inodes, 896000 Blöcke 44800 Blöcke (5.00%) reserviert für den Superuser Erster Datenblock=0 Maximale Dateisystem-Blöcke=918552576 28 Blockgruppen 32768 Blöcke pro Gruppe, 32768 Fragmente pro Gruppe 8000 Inodes pro Gruppe Superblock-Sicherungskopien gespeichert in den Blöcken: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Platz für Gruppentabellen wird angefordert: erledigt Inode-Tabellen werden geschrieben: erledigt Erstelle Journal (16384 Blöcke): erledigt Schreibe Superblöcke und Dateisystem-Accountinginformationen: erledigt (mounted /media/USERNAME/rootfs via graphical tools) USERNAME@PCNAME:~$ cd /media/USERNAME/rootfs USERNAME@PCNAME:/media/USERNAME/rootfs$ sudo tar -xjf /home/USERNAME/Desktop/Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 . USERNAME@PCNAME:/media/USERNAME/rootfs$ cat etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> /dev/root / ext3 noatime,errors=remount-ro 0 1 tmpfs /tmp tmpfs defaults 0 0 USERNAME@PCNAME:/media/USERNAME/rootfs$ cat etc/network/interfaces auto lo eth0 iface lo inet loopback iface eth0 inet dhcp USERNAME@PCNAME:/media/USERNAME/rootfs$ sync USERNAME@PCNAME:/media/USERNAME/rootfs$ cd .. USERNAME@PCNAME:/media/USERNAME$ umount rootfs/ USERNAME@PCNAME:/media/USERNAME$
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.14.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Apr 1 22:54:58 PDT 2014 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Seagate FreeAgent DockStar [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 122460K/131072K available (4779K kernel code, 352K rwdata, 1644K rodata, 213K init, 424K bss, 8612K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc064df14 (6424 kB) [ 0.000000] .init : 0xc064e000 - 0xc0683444 ( 214 kB) [ 0.000000] .data : 0xc0684000 - 0xc06dc3c4 ( 353 kB) [ 0.000000] .bss : 0xc06dc3c4 - 0xc074665c ( 425 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns [ 5.431378] Console: colour dummy device 80x30 [ 5.431408] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 5.521154] pid_max: default: 32768 minimum: 301 [ 5.521261] Security Framework initialized [ 5.521326] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 5.521346] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 5.521933] Initializing cgroup subsys devices [ 5.521957] Initializing cgroup subsys freezer [ 5.521971] Initializing cgroup subsys net_cls [ 5.521982] Initializing cgroup subsys blkio [ 5.522056] CPU: Testing write buffer coherency: ok [ 5.522447] Setting up static identity map for 0x485fa0 - 0x485fdc [ 5.524556] devtmpfs: initialized [ 5.527168] prandom: seed boundary self test passed [ 5.531267] prandom: 100 self tests passed [ 5.531283] pinctrl core: initialized pinctrl subsystem [ 5.531661] regulator-dummy: no parameters [ 5.531998] NET: Registered protocol family 16 [ 5.532426] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 5.533216] cpuidle: using governor ladder [ 5.533232] cpuidle: using governor menu [ 5.533342] Kirkwood: MV88F6281-A0, TCLK=200000000. [ 5.533363] Feroceon L2: Enabling L2 [ 5.533401] Feroceon L2: Cache support initialised. [ 5.538615] bio: create slab <bio-0> at 0 [ 5.539065] vgaarb: loaded [ 5.539366] usbcore: registered new interface driver usbfs [ 5.539434] usbcore: registered new interface driver hub [ 5.539561] usbcore: registered new device driver usb [ 5.540292] Switched to clocksource orion_clocksource [ 5.565038] NET: Registered protocol family 2 [ 5.565688] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 5.565714] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 5.565734] TCP: Hash tables configured (established 1024 bind 1024) [ 5.565803] TCP: reno registered [ 5.565818] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 5.565840] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 5.566032] NET: Registered protocol family 1 [ 5.566354] RPC: Registered named UNIX socket transport module. [ 5.566366] RPC: Registered udp transport module. [ 5.566372] RPC: Registered tcp transport module. [ 5.566379] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.566726] NetWinder Floating Point Emulator V0.97 (double precision) [ 5.567249] futex hash table entries: 256 (order: -1, 3072 bytes) [ 5.567398] audit: initializing netlink subsys (disabled) [ 5.567445] audit: type=2000 audit(0.120:1): initialized [ 5.568099] bounce pool size: 64 pages [ 5.568169] zbud: loaded [ 5.568358] VFS: Disk quotas dquot_6.5.2 [ 5.568411] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.568695] NFS: Registering the id_resolver key type [ 5.568750] Key type id_resolver registered [ 5.568759] Key type id_legacy registered [ 5.568777] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 5.568786] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 5.568940] jffs2: version 2.2. (NAND) (SUMMARY) \0xc2\0xa9 2001-2006 Red Hat, Inc. [ 5.569221] msgmni has been set to 239 [ 5.569339] Key type big_key registered [ 5.571178] alg: No test for stdrng (krng) [ 5.571270] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 5.571281] io scheduler noop registered [ 5.571289] io scheduler deadline registered [ 5.571319] io scheduler cfq registered (default) [ 5.571575] mv_xor mv_xor.0: Marvell shared XOR driver [ 5.610381] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 5.650348] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 5.650470] mv_xor mv_xor.1: Marvell shared XOR driver [ 5.690355] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 5.730353] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 5.730647] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.751303] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A [ 6.289834] console [ttyS0] enabled [ 6.294422] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 6.300834] nand: Micron MT29F2G08AAD [ 6.304516] nand: 256MiB, SLC, page size: 2048, OOB size: 64 [ 6.310206] Scanning device for bad blocks [ 6.529850] 4 cmdlinepart partitions found on MTD device orion_nand [ 6.536160] Creating 4 MTD partitions on "orion_nand": [ 6.541343] 0x000000000000-0x000000100000 : "u-boot" [ 6.546616] 0x000000100000-0x000000500000 : "uImage" [ 6.551904] 0x000000500000-0x000002500000 : "rootfs" [ 6.557177] 0x000002500000-0x000010000000 : "data" [ 6.563078] libphy: Fixed MDIO Bus: probed [ 6.573332] libphy: orion_mdio_bus: probed [ 6.577531] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.661031] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:10:75:1a:d2:81 [ 7.669966] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.676544] ehci-pci: EHCI PCI platform driver [ 7.681082] ehci-orion: EHCI orion driver [ 7.685174] orion-ehci orion-ehci.0: EHCI Host Controller [ 7.690638] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 7.698352] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 7.720325] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 7.726441] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.733284] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.740549] usb usb1: Product: EHCI Host Controller [ 7.745453] usb usb1: Manufacturer: Linux 3.14.0-kirkwood-tld-1 ehci_hcd [ 7.752199] usb usb1: SerialNumber: orion-ehci.0 [ 7.757388] hub 1-0:1.0: USB hub found [ 7.761215] hub 1-0:1.0: 1 port detected [ 7.765703] mousedev: PS/2 mouse device common for all mice [ 8.080346] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.231740] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 8.238485] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.245677] usb 1-1: Product: USB2.0 Hub [ 8.250393] hub 1-1:1.0: USB hub found [ 8.254489] hub 1-1:1.0: 4 ports detected [ 8.540617] usb 1-1.4: new high-speed USB device number 3 using orion-ehci [ 8.656865] usb 1-1.4: New USB device found, idVendor=1307, idProduct=0165 [ 8.663797] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.671169] usb 1-1.4: Product: USB Mass Storage Device [ 8.676418] usb 1-1.4: Manufacturer: USBest Technology [ 8.681597] usb 1-1.4: SerialNumber: 100202500155a8 [ 8.780320] rtc-mv rtc-mv: internal RTC not ticking [ 8.785332] i2c /dev entries driver [ 8.789454] hidraw: raw HID events driver (C) Jiri Kosina [ 8.795196] drop_monitor: Initializing network drop monitor service [ 8.801706] TCP: cubic registered [ 8.805038] NET: Registered protocol family 17 [ 8.809628] Key type dns_resolver registered [ 8.814418] registered taskstats version 1 [ 8.819013] regulator-dummy: incomplete constraints, leaving on [ 8.825305] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 8.832660] Waiting 10 sec before mounting root device... [ 18.840713] VFS: Cannot open root device "sda1" or unknown-block(0,0): error -19 [ 18.848148] Please append a correct "root=" boot option; here are the available partitions: [ 18.856578] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 18.864886] CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.0-kirkwood-tld-1 #1 [ 18.871993] [<c00142fc>] (unwind_backtrace) from [<c0010e78>] (show_stack+0x10/0x14) [ 18.879782] [<c0010e78>] (show_stack) from [<c047e8c8>] (panic+0x80/0x1e4) [ 18.886693] [<c047e8c8>] (panic) from [<c064f018>] (mount_block_root+0x1fc/0x240) [ 18.894214] [<c064f018>] (mount_block_root) from [<c064f140>] (mount_root+0xe4/0x10c) [ 18.902079] [<c064f140>] (mount_root) from [<c064f28c>] (prepare_namespace+0x124/0x184) [ 18.910119] [<c064f28c>] (prepare_namespace) from [<c064ec48>] (kernel_init_freeable+0x1f8/0x240) [ 18.919031] [<c064ec48>] (kernel_init_freeable) from [<c047cb48>] (kernel_init+0x8/0xe4) [ 18.927159] [<c047cb48>] (kernel_init) from [<c000e050>] (ret_from_fork+0x14/0x24)