Seagate Goflex Net hangs at startup January 15, 2015 12:03PM |
Registered: 10 years ago Posts: 19 |
U-Boot 2011.12 (Apr 18 2012 - 23:08:20) Seagate GoFlexNet SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Using egiga0 device ping failed; host 10.10.10.5 is not alive Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1751 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1730 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. Reset IDE: ide_preinit failed ** No boot file defined ** ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ........ read_nand_cached: error reading nand off 0x187f800 size 8192 bytes read_nand_cached: error reading nand off 0x1881800 size 8192 bytes read_nand_cached: error reading nand off 0x1883800 size 8192 bytes read_nand_cached: error reading nand off 0x1885800 size 8192 bytes read_nand_cached: error reading nand off 0x1887800 size 8192 bytes read_nand_cached: error reading nand off 0x1889800 size 8192 bytes read_nand_cached: error reading nand off 0x188b800 size 8192 bytes read_nand_cached: error reading nand off 0x188d800 size 8192 bytes read_nand_cached: error reading nand off 0x188f800 size 8192 bytes read_nand_cached: error reading nand off 0x1891800 size 8192 bytes read_nand_cached: error reading nand off 0x1893800 size 8192 bytes read_nand_cached: error reading nand off 0x1895800 size 8192 bytes read_nand_cached: error reading nand off 0x1897800 size 8192 bytes read_nand_cached: error reading nand off 0x1899800 size 8192 bytes read_nand_cached: error reading nand off 0x189b800 size 8192 bytes read_nand_cached: error reading nand off 0x189d800 size 8192 bytes read_nand_cached: error reading nand off 0x189f800 size 8192 bytes . done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
U-Boot 2011.12 (Apr 18 2012 - 23:08:20) Seagate GoFlexNet SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Using egiga0 device ping failed; host 10.10.10.5 is not alive Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1751 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1730 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 (usbda1) 2822232 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 6114335 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.17.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2822168 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.17.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6114271 Bytes = 5.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000c11). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
Re: Seagate Goflex Net hangs at startup January 15, 2015 12:36PM |
Admin Registered: 13 years ago Posts: 18,560 |
Quote
cd /media/sdb1/boot
cp -a zImage-3.17.0-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-3.17.0-kirkwood-tld-1 -d /media/sdb1/boot/zImage.fdt /media/sdb1/boot/uImage
sync
Re: Seagate Goflex Net hangs at startup January 15, 2015 01:56PM |
Registered: 10 years ago Posts: 19 |
Re: Seagate Goflex Net hangs at startup January 15, 2015 05:21PM |
Registered: 10 years ago Posts: 19 |
Re: Seagate Goflex Net hangs at startup January 15, 2015 10:58PM |
Admin Registered: 13 years ago Posts: 18,560 |
Re: Seagate Goflex Net hangs at startup January 16, 2015 09:46AM |
Registered: 10 years ago Posts: 19 |
cd /tmp wget http://projects.doozan.com/debian/kirkwood.debian-wheezy.sh chmod +x kirkwood.debian-wheezy.sh export PATH=$PATH:/usr/sbin:/sbin ./kirkwood.debian-wheezy.sh
Re: Seagate Goflex Net hangs at startup January 16, 2015 10:10AM |
Registered: 10 years ago Posts: 19 |
dmesg | grep -i 'bad' [ 11.863780] Scanning device for bad blocks [ 11.882630] Bad eraseblock 196 at 0x000001880000 [ 11.966838] Bad eraseblock 1258 at 0x000009d40000
flash_erase /dev/mtd0 0 4
Re: Seagate Goflex Net hangs at startup January 16, 2015 10:15AM |
Admin Registered: 13 years ago Posts: 18,560 |
> dmesg | grep -i 'bad' > > [ 11.863780] Scanning device for bad blocks > [ 11.882630] Bad eraseblock 196 at > 0x000001880000 > [ 11.966838] Bad eraseblock 1258 at > 0x000009d40000 >>
> flash_erase /dev/mtd0 0 4 >
Re: Seagate Goflex Net hangs at startup January 16, 2015 10:33AM |
Registered: 10 years ago Posts: 19 |
U-Boot 2014.07-tld-2 (Sep 20 2014 - 00:58:11) Seagate GoFlex Net SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB ## Error: flags type check failure for "ethaddr" <= "MYMACADDRESS" (type: m) himport_r: can't insert "ethaddr=MYMACADDRESS" into hash table In: serial Out: serial Err: serial Net: egiga0 Warning: failed to set MAC address
Re: Seagate Goflex Net hangs at startup March 14, 2015 04:54PM |
Registered: 9 years ago Posts: 1,037 |