Welcome! Log In Create A New Profile

Advanced

NSA 325 v2 bricked

Posted by buec65 
NSA 325 v2 bricked
January 15, 2017 11:51AM
My NSA325v2 is bricked

No network and only frontusb is working after boot, before starting kernel networks seems to be OK.

Restarting system.
Reseting !! 
ü
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: DB-88F6282A-BP LE 

U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz 

DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000   size 512MB 
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled 
Write allocate disabled


USB 0: host mode
	[BlueDBG] reseting SoC Pex[0]  0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
	[BlueDBG] reseting SoC Pex[1]  0 ...
	[BlueDBG] reseting SoC Pex[1]  1 ...
	[BlueDBG] reseting SoC Pex[1]  2 ...
	[BlueDBG] reseting SoC Pex[1]  3 ...
	[BlueDBG] reseting SoC Pex[1]  4 ...
	[BlueDBG] reseting SoC Pex[1]  5 ...
	[BlueDBG] reseting SoC Pex[1]  6 ...
	[BlueDBG] reseting SoC Pex[1]  7 ...
	[BlueDBG] reseting SoC Pex[1]  8 ...
	[BlueDBG] reseting SoC Pex[1]  9 ...
	[BlueDBG] reseting SoC Pex[1]  10 ...
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  2  1  0 

NAND read: device 0 offset 0x4640000, size 0xa00000


Reading data from 0x4640000 --   0% complete.
Reading data from 0x4659800 --   1% complete.
Reading data from 0x4673000 --   2% complete.
Reading data from 0x468c800 --   3% complete.
Reading data from 0x46a6000 --   4% complete.
Reading data from 0x46bf800 --   5% complete.
Reading data from 0x46d9800 --   6% complete.
Reading data from 0x46f3000 --   7% complete.
Reading data from 0x470c800 --   8% complete.
Reading data from 0x4726000 --   9% complete.
Reading data from 0x473f800 --  10% complete.
Reading data from 0x4759800 --  11% complete.
Reading data from 0x4773000 --  12% complete.
Reading data from 0x478c800 --  13% complete.
Reading data from 0x47a6000 --  14% complete.
Reading data from 0x47bf800 --  15% complete.
Reading data from 0x47d9800 --  16% complete.
Reading data from 0x47f3000 --  17% complete.
Reading data from 0x480c800 --  18% complete.
Reading data from 0x4826000 --  19% complete.
Reading data from 0x483f800 --  20% complete.
Reading data from 0x4859800 --  21% complete.
Reading data from 0x4873000 --  22% complete.
Reading data from 0x488c800 --  23% complete.
Reading data from 0x48a6000 --  24% complete.
Reading data from 0x48bf800 --  25% complete.
Reading data from 0x48d9800 --  26% complete.
Reading data from 0x48f3000 --  27% complete.
Reading data from 0x490c800 --  28% complete.
Reading data from 0x4926000 --  29% complete.
Reading data from 0x493f800 --  30% complete.
Reading data from 0x4959800 --  31% complete.
Reading data from 0x4973000 --  32% complete.
Reading data from 0x498c800 --  33% complete.
Reading data from 0x49a6000 --  34% complete.
Reading data from 0x49bf800 --  35% complete.
Reading data from 0x49d9800 --  36% complete.
Reading data from 0x49f3000 --  37% complete.
Reading data from 0x4a0c800 --  38% complete.
Reading data from 0x4a26000 --  39% complete.
Reading data from 0x4a3f800 --  40% complete.
Reading data from 0x4a59800 --  41% complete.
Reading data from 0x4a73000 --  42% complete.
Reading data from 0x4a8c800 --  43% complete.
Reading data from 0x4aa6000 --  44% complete.
Reading data from 0x4abf800 --  45% complete.
Reading data from 0x4ad9800 --  46% complete.
Reading data from 0x4af3000 --  47% complete.
Reading data from 0x4b0c800 --  48% complete.
Reading data from 0x4b26000 --  49% complete.
Reading data from 0x4b3f800 --  50% complete.
Reading data from 0x4b59800 --  51% complete.
Reading data from 0x4b73000 --  52% complete.
Reading data from 0x4b8c800 --  53% complete.
Reading data from 0x4ba6000 --  54% complete.
Reading data from 0x4bbf800 --  55% complete.
Reading data from 0x4bd9800 --  56% complete.
Reading data from 0x4bf3000 --  57% complete.
Reading data from 0x4c0c800 --  58% complete.
Reading data from 0x4c26000 --  59% complete.
Reading data from 0x4c3f800 --  60% complete.
Reading data from 0x4c59800 --  61% complete.
Reading data from 0x4c73000 --  62% complete.
Reading data from 0x4c8c800 --  63% complete.
Reading data from 0x4ca6000 --  64% complete.
Reading data from 0x4cbf800 --  65% complete.
Reading data from 0x4cd9800 --  66% complete.
Reading data from 0x4cf3000 --  67% complete.
Reading data from 0x4d0c800 --  68% complete.
Reading data from 0x4d26000 --  69% complete.
Reading data from 0x4d3f800 --  70% complete.
Reading data from 0x4d59800 --  71% complete.
Reading data from 0x4d73000 --  72% complete.
Reading data from 0x4d8c800 --  73% complete.
Reading data from 0x4da6000 --  74% complete.
Reading data from 0x4dbf800 --  75% complete.
Reading data from 0x4dd9800 --  76% complete.
Reading data from 0x4df3000 --  77% complete.
Reading data from 0x4e0c800 --  78% complete.
Reading data from 0x4e26000 --  79% complete.
Reading data from 0x4e3f800 --  80% complete.
Reading data from 0x4e59800 --  81% complete.
Reading data from 0x4e73000 --  82% complete.
Reading data from 0x4e8c800 --  83% complete.
Reading data from 0x4ea6000 --  84% complete.
Reading data from 0x4ebf800 --  85% complete.
Reading data from 0x4ed9800 --  86% complete.
Reading data from 0x4ef3000 --  87% complete.
Reading data from 0x4f0c800 --  88% complete.
Reading data from 0x4f26000 --  89% complete.
Reading data from 0x4f3f800 --  90% complete.
Reading data from 0x4f59800 --  91% complete.
Reading data from 0x4f73000 --  92% complete.
Reading data from 0x4f8c800 --  93% complete.
Reading data from 0x4fa6000 --  94% complete.
Reading data from 0x4fbf800 --  95% complete.
Reading data from 0x4fd9800 --  96% complete.
Reading data from 0x4ff3000 --  97% complete.
Reading data from 0x500c800 --  98% complete.
Reading data from 0x5026000 --  99% complete.
Reading data from 0x503f800 -- 100% complete.
 10485760 bytes read: OK
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2015-05-15   4:20:19 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5796192 Bytes =  5.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................................................................................................................................................................ done, booting the kernel.

Linux version 2.6.31.8 (root@BuildMachine) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #2 Fri May 15 12:20:01 CST 2015
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 506752KB available (5360K code, 302K data, 2872K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
invoking softwareStaggeredSpinUp()..., it will delay 5 seconds to spin up the second harddisk

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB 
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
PEX1_MEM ....base e8000000, size 128MB 
PEX1_IO ....base f2100000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
NFLASH_CS ....base fa000000, size   2MB 
SPI_CS ....base f4000000, size  16MB 
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB 

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- DB-88F6282A-BP  Soc: MV88F6282 Rev 1 LE

 Detected Tclk 200000000 and SysClk 533333333 
Marvell USB EHCI Host controller #0: d003a740
	[BlueDBG] reseting SoC Pex[0]  0 ...
PEX0 interface detected Link X1
	[BlueDBG] reseting SoC Pex[1]  0 ...
	[BlueDBG] reseting SoC Pex[1]  1 ...
	[BlueDBG] reseting SoC Pex[1]  2 ...
	[BlueDBG] reseting SoC Pex[1]  3 ...
	[BlueDBG] reseting SoC Pex[1]  4 ...
	[BlueDBG] reseting SoC Pex[1]  5 ...
	[BlueDBG] reseting SoC Pex[1]  6 ...
	[BlueDBG] reseting SoC Pex[1]  7 ...
	[BlueDBG] reseting SoC Pex[1]  8 ...
	[BlueDBG] reseting SoC Pex[1]  9 ...
	[BlueDBG] reseting SoC Pex[1]  10 ...
PEX1 interface detected no Link.
pci 0000:00:01.0: PME# supported from D0 D3hot
pci 0000:00:01.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
gpio_dev = fd00000
LED_SET_CTL_IOC_NUM= 6702
High gpio polarity = 50 
High gpio polarity = 70 
Enable Interrupt
mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
mv88f6281_wdt: HW Watchdog timeout    = 15 sec.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 990
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
Wake up disk0......
Wake up disk1......
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
EnablePowerSaving 
PowerSavingTime = 15
No found HD
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 1 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Network Fast Processing (Routing) supported - (Disabled)
  o Driver ERROR statistics enabled
  o Proc tool API enabled
  o SKB Reuse supported - (Disabled)
  o SKB Recycle supported - (Disabled)
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
     o register under mv88fx_eth platform
     o eth0, ifindex = 2, GbE port = 0

mvFpRuleDb (d10a0000): 16384 entries, 65536 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 100 at 0x000000c80000
Bad eraseblock 200 at 0x000001900000
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
rtc-pcf8563 0-0051: retrieved date/time is not valid.
rtc-pcf8563 0-0051: hctosys: invalid date/time
Freeing init memory: 2872K
*** Stage 1: Setup system and device drivers ***
usb 1-1: new high speed USB device using ehci_marvell and address 2
eth0: mac address changed
egiga0: started
ADDRCONF(NETDEV_UP): egiga0: link is not ready
rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
rtc-pcf8563 0-0051: retrieved date/time is not valid.
*** Stage 2: Prepare the root file system ***
Mount system partition...
yaffs: dev is 32505864 name is "mtdblock8" ro
yaffs: passed flags ""
storage_gen_mntfw.sh: no internal disk available
1
WARNING: No valid partition on HDD or no HDD plugged!
WARNING: No valid partition on HDD or no HDD plugged
Boot from RAM disk
usb 1-1: device descriptor read/64, error -110
Mount system disk image ...
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
/etc/zyxel/conf does not exist.. recoverying /etc/zyxel..
rm: can't remove '/etc/zyxel/lost+found': Directory not empty
Umount /etc/zyxel
flash_eraseall mtd4

Erasing 128 Kibyte @ 0 --  0 % complete.
Erasing 128 Kibyte @ 20000 --  1 % complete.
Erasing 128 Kibyte @ 40000 --  2 % complete.
Erasing 128 Kibyte @ 60000 --  3 % complete.
Erasing 128 Kibyte @ 80000 --  5 % complete.
Erasing 128 Kibyte @ a0000 --  6 % complete.
Erasing 128 Kibyte @ c0000 --  7 % complete.
Erasing 128 Kibyte @ e0000 --  8 % complete.
Erasing 128 Kibyte @ 100000 -- 10 % complete.
Erasing 128 Kibyte @ 120000 -- 11 % complete.
Erasing 128 Kibyte @ 140000 -- 12 % complete.
Erasing 128 Kibyte @ 160000 -- 13 % complete.
Erasing 128 Kibyte @ 180000 -- 15 % complete.
Erasing 128 Kibyte @ 1a0000 -- 16 % complete.
Erasing 128 Kibyte @ 1cyaffs: dev is 32505860 name is "mtdblock4" rw
0000 -- 17 % comyaffs: passed flags ""
plete.
Erasing 128 Kibyte @ 1e0000 -- 18 % complete.
Erasing 128 Kibyte @ 200000 -- 20 % complete.
Erasing 128 Kibyte @ 220000 -- 21 % complete.
Erasing 128 Kibyte @ 240000 -- 22 % complete.
Erasing 128 Kibyte @ 260000 -- 23 % complete.
Erasing 128 Kibyte @ 280000 -- 25 % complete.
Erasing 128 Kibyte @ 2a0000 -- 26 % complete.
Erasing 128 Kibyte @ 2c0000 -- 27 % complete.
Erasing 128 Kibyte @ 2e0000 -- 28 % complete.
Erasing 128 Kibyte @ 300000 -- 30 % complete.
Erasing 128 Kibyte @ 320000 -- 31 % complete.
Erasing 128 Kibyte @ 340000 -- 32 % complete.
Erasing 128 Kibyte @ 360000 -- 33 % complete.
Erasing 128 Kibyte @ 380000 -- 35 % complete.
Erasing 128 Kibyte @ 3a0000 -- 36 % complete.
Erasing 128 Kibyte @ 3c0000 -- 37 % complete.
Erasing 128 Kibyte @ 3e0000 -- 38 % complete.
Erasing 128 Kibyte @ 400000 -- 40 % complete.
Erasing 128 Kibyte @ 420000 -- 41 % complete.
Erasing 128 Kibyte @ 440000 -- 42 % complete.
Erasing 128 Kibyte @ 460000 -- 43 % complete.
Erasing 128 Kibyte @ 480000 -- 45 % complete.
Erasing 128 Kibyte @ 4a0000 -- 46 % complete.
Erasing 128 Kibyte @ 4c0000 -- 47 % complete.
Erasing 128 Kibyte @ 4e0000 -- 48 % complete.
Erasing 128 Kibyte @ 500000 -- 50 % complete.
Erasing 128 Kibyte @ 520000 -- 51 % complete.
Erasing 128 Kibyte @ 540000 -- 52 % complete.
Erasing 128 Kibyte @ 560000 -- 53 % complete.
Erasing 128 Kibyte @ 580000 -- 55 % complete.
Erasing 128 Kibyte @ 5a0000 -- 56 % complete.
Erasing 128 Kibyte @ 5c0000 -- 57 % complete.
Erasing 128 Kibyte @ 5e0000 -- 58 % complete.
Erasing 128 Kibyte @ 600000 -- 60 % complete.
Erasing 128 Kibyte @ 620000 -- 61 % complete.
Erasing 128 Kibyte @ 640000 -- 62 % complete.
Erasing 128 Kibyte @ 660000 -- 63 % complete.
Erasing 128 Kibyte @ 680000 -- 65 % complete.
Erasing 128 Kibyte @ 6a0000 -- 66 % complete.
Erasing 128 Kibyte @ 6c0000 -- 67 % complete.
Erasing 128 Kibyte @ 6e0000 -- 68 % complete.
Erasing 128 Kibyte @ 700000 -- 70 % complete.
Erasing 128 Kibyte @ 720000 -- 71 % complete.
Erasing 128 Kibyte @ 740000 -- 72 % complete.
Erasing 128 Kibyte @ 760000 -- 73 % complete.
Erasing 128 Kibyte @ 780000 -- 75 % complete.
Erasing 128 Kibyte @ 7a0000 -- 76 % complete.
Erasing 128 Kibyte @ 7c0000 -- 77 % complete.
Erasing 128 Kibyte @ 7e0000 -- 78 % complete.
Erasing 128 Kibyte @ 800000 -- 80 % complete.
Erasing 128 Kibyte @ 820000 -- 81 % complete.
Erasing 128 Kibyte @ 840000 -- 82 % complete.
Erasing 128 Kibyte @ 860000 -- 83 % complete.
Erasing 128 Kibyte @ 880000 -- 85 % complete.
Erasing 128 Kibyte @ 8a0000 -- 86 % complete.
Erasing 128 Kibyte @ 8c0000 -- 87 % complete.
Erasing 128 Kibyte @ 8e0000 -- 88 % complete.
Erasing 128 Kibyte @ 900000 -- 90 % complete.
Erasing 128 Kibyte @ 920000 -- 91 % complete.
Erasing 128 Kibyte @ 940000 -- 92 % complete.
Erasing 128 Kibyte @ 960000 -- 93 % complete.
Erasing 128 Kibyte @ 980000 -- 95 % complete.
Erasing 128 Kibyte @ 9a0000 -- 96 % complete.
Erasing 128 Kibyte @ 9c0000 -- 97 % complete.
Erasing 128 Kibyte @ 9e0000 -- 98 % complete.
Mount /etc/zyxel back
/etc/init.d/rcS: line 420: can't create /sys/block/sda/queue/read_ahead_kb: nonexistent directory
Start rcS2 of ZyXEL style
Set the phy back to auto-negotiation mode
base address = 4014e000
words[0] = phypoke
words[1] = 1
words[2] = 4
words[3] = 1e1
:GbitPhy[0x00000001:0x00000004] <= 0x000001e1
base address = 4014e000
words[0] = phypoke
words[1] = 1
words[2] = 9
words[3] = 300
:GbitPhy[0x00000001:0x00000009] <= 0x00000300
base address = 4014e000
words[0] = phypoke
words[1] = 1
words[2] =NTFS driver 2.1.29 [Flags: R/O MODULE].
 0
words[3] = 9140
:GbitPhy[0x00000001:0x00000000] <= 0x00009140
*** Stage 3: Start services on HDD ***
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3011.12.23 [Flags: R/W MODULE].
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
PPP BSD Compression module registered
modprobe: module fuse not found in modules.dep
usb 1-1: device descriptor read/64, error -110
In hub_port_init, and number is 0, retry 0, port 1 .....
usb 1-1: new high speed USB device using ehci_marvell and address 3

Press ENTER to continue...
Starting zylogd...
 zylog starts.
Starting uamd...
Starting ZySH daemon and client...
Start NSA-220 system daemon....
 Start ZySH daemon
zyshd: version 2.0.0 (build: 11:28:55 May 15 2015)
% zylog init start 
cat: can't open '/var/run/syslog-ng.pid': No such file or directory
Try to KILL SIGHUP to syslog-ng: pid=0
syslog-ng not running, start /usr/sbin/syslog-ng
Dec  4 01:20:19 (none) syslog-ng[1334]: syslog-ng starting up; version='2.0.10'
zyio_open_config success. (/etc/__system_default.xml, 0)
zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0)
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
/bin/hostname NSA325-v2
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2015-05-15 11:23:13 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

Init SMB DB access... 
rm: can't remove '/var/log/samba/smb.db': No such file or directory
WARNING: can't open config file: /etc/ssl/openssl.cnf
Generating a 1024 bit RSA private key
...++++++
....................++++++
writing new private key to '/etc/zyxel/cert/key/default_key.cer'
-----
WARNING: can't open config file: /etc/ssl/openssl.cnf
zyio_container_create_template(/etc/__system_default.xml): scope:[network/wlan] list:[wlan_list] type:[wlan_t] is not existed
usb 1-1: device descriptor read/64, error -110
Assemble volume....
[1383] server write-only FIFO is opened (fd=6)
[1383] server read-only FIFO is opened (fd=7)
[1383] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 280
 Startup config
POLLHUP on 7
  pid = 1383
[1383] is disconnected
[1521] server write-only FIFO is opened (fd=6)
[1521] server read-only FIFO is opened (fd=7)
[1521] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 14
argc = 1,  func = 17
argc = 2,  func = 105
argid[1]: 1087; argv[1]: ge1
argc = 5,  func = 108
argid[1]: 1087; argv[1]: ge1
argid[2]: 313; argv[2]: ip
argid[3]: 434; argv[3]: address
argid[4]: 539; argv[4]: dhcp
killall: httpd: no process killed
Dec  4 01:20:25 (none) httpd[1529]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Dec  4 01:20:25 (none) httpd[1529]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Dec  4 01:20:25 (none) httpd[1529]: [warn] RSA server certificate CommonName (CN) `NSA325-v2' does NOT match server name!?
Dec  4 01:20:25 (none) httpd[1529]: [error] mod_auth_zyxel: initialized.
argc = 3,  func = 106
argid[1]: 1087; argv[1]: ge1
argid[2]: 350; argv[2]: exit
argc = 2,  func = 444
argid[1]: 1080; argv[1]: 192.168.1.1
argc = 3,  func = 446
argid[1]: 879; argv[1]: fetch
argid[2]: 632; argv[2]: auto
Dec  4 01:20:26 (none) httpd[1530]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Dec  4 01:20:26 (none) httpd[1530]: [warn] RSA server certificate CommonName (CN) `NSA325-v2' does NOT match server name!?
Dec  4 01:20:26 (none) httpd[1530]: [error] mod_auth_zyxel: initialized.
/bin/rm -f /var/zyxel/zysh/egiga0.metric
/bin/ip route del default via 0.0.0.0 dev egiga0
RTNETLINK answers: No such process
[1536] server write-only FIFO is opened (fd=9)
[1536] server read-only FIFO is opened (fd=10)
[1536] server error read-only FIFO is opened (fd=11)
argc = 7,  func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1415; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 478; argv[6]: alert
mail server '1' log_category(all) is:alert 
argc = 1,  func = 445
POLLHUP on 10
  pid = 1536
[1536] is disconnected
argc = 7,  func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1415; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 375; argv[6]: all
mail server '1' log_category(all) is:all 
argc = 1,  func = 72
/usr/sbin/ntpdate_agent 
argc = 2,  func = 68
argid[1]: 1079; argv[1]: time.stdtime.gov.tw
argc = 2,  func = 60
argid[1]: 1130; argv[1]: +0800
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
Dec  4 09:20:30 (none) ntpdate[1588]: can't find host time.stdtime.gov.tw
Dec  4 09:20:30 (none) ntpdate[1588]: no servers can be used, exiting
argc = 1,  func = 38
killall: pure-ftpd: no process killed
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2015-05-15 11:23:13 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

argc = 4,  func = 414
argid[1]: 1250; argv[1]: yes
argid[2]: 1251; argv[2]: yes
argid[3]: 1252; argv[3]: yes
Dec  4 09:20:33 (none) dhcpcd[1571]: timed out waiting for a valid DHCP server response
argc = 2,  func DisablePowerSaving
= 147
argid[1]:TimerState = 0
 1155; argv[1]: EnablePowerSaving 
15
PowerSavingTime = 15
No found HD
test0
Test1
Test2
Test3:
argc = 2,  func = 161
argid[1]: 1160; argv[1]: g
exec_cmd complete
eth status = g 
ethtest0
Test1
Test2
Test3:
argc = 2,  func = 676
argid[1]: 1087; argv[1]: ge1
Dec  4 09:20:34 (none) ntpdate[1741]: can't find host ntp1.cs.wisc.edu
Dec  4 09:20:34 (none) ntpdate[1741]: no servers can be used, exiting
Dec  4 09:20:34 (none) httpd[1739]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Dec  4 09:20:34 (none) httpd[1739]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Dec  4 09:20:34 (none) httpd[1739]: [warn] RSA server certificate CommonName (CN) `NSA325-v2' does NOT match server name!?
Dec  4 09:20:34 (none) httpd[1739]: [error] mod_auth_zyxel: initialized.
argc = 2,  func = 163
argid[1]: 1161; argv[1]: enable
argc = 2,  func = 18
argid[1]: 350; argv[1]: exit
argc = 1,  func = 20
POLLHUP on 7
  pid = 1521
[1521] is disconnected
Dec  4 09:20:37 (none) httpd[1754]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Dec  4 09:20:37 (none) httpd[1754]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Dec  4 09:20:37 (none) httpd[1754]: [warn] RSA server certificate CommonName (CN) `NSA325-v2' does NOT match server name!?
Dec  4 09:20:37 (none) httpd[1754]: [error] mod_auth_zyxel: initialized.
configure terminal ip smb internal disable "/i-data/md0"
[1762] server write-only FIFO is opened (fd=6)
[1762] server read-only FIFO is opened (fd=7)
[1762] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 184
argid[1]: 634; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1183; argv[3]: "/i-data/md0"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2203 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
  pid = 1762
[1762] is disconnected
configure terminal ip smb internal disable "/i-data/md1"
[1767] server write-only FIFO is opened (fd=6)
[1767] server read-only FIFO is opened (fd=7)
[1767] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 184
argid[1]: 634; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1183; argv[3]: "/i-data/md1"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2203 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
  pid = 1767
[1767] is disconnected
Dec  4 09:20:38 (none) httpd[1755]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Dec  4 09:20:38 (none) httpd[1755]: [warn] RSA server certificate CommonName (CN) `NSA325-v2' does NOT match server name!?
Dec  4 09:20:38 (none) httpd[1755]: [error] mod_auth_zyxel: initialized.
usb 1-1: device descriptor read/64, error -110
In hub_port_init, and number is 0, retry 1, port 1 .....
usb 1-1: new high speed USB device using ehci_marvell and address 4
Dec  4 09:20:42 (none) ntpdate[1798]: can't find host ntp1.gbg.netnod.se
Dec  4 09:20:42 (none) ntpdate[1798]: no servers can be used, exiting
usb 1-1: device not accepting address 4, error -110
In hub_port_init, and number is 0, retry 2, port 1 .....
usb 1-1: new high speed USB device using ehci_marvell and address 5
Dec  4 09:20:50 (none) ntpdate[1801]: can't find host ntp2.cs.wisc.edu
Dec  4 09:20:50 (none) ntpdate[1801]: no servers can be used, exiting
Dec  4 09:20:57 (none) zcip: init egiga0
Dec  4 09:20:57 (none) zcip: start, interface egiga0
usb 1-1: device not accepting address 5, error -110
In hub_port_init, and number is 0, retry 3, port 1 .....
hub 1-0:1.0: unable to enumerate USB device on port 1
Starting smbd...
Starting nmbd...
Starting NSU Agent...
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb2: configuration #1 chosen from 1 choice
hotplug918add:
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hotplug919add:9
hotplug919add:[9/0/0]USB hub device:09h/xxh/xxh
Starting copy auto daylight saving tzfile to /i-data/md0/.system/ ...
cp -a /usr/local/zoneinfo /i-data/md0/.system/
cp: can't create directory '/i-data/md0/.system/': No such file or directory
storage_gen_swap.sh: not enough space to dd swap file
GMT offset=28800s
setting system time zone to tz_minuteswest=-480
mknod: /dev/btncpy: File exists
setLED COPY OFF
led_state_map_addr = 10
[2274] server write-only FIFO is opened (fd=6)
[2274] server read-only FIFO is opened (fd=7)
[2274] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 351
argid[1]: 1226; argv[1]: former
Warning - readback failed
POLLHUP on 7
  pid = 2274
[2274] is disconnected
schedule_controller is already running now.
Starting "/etc/init.d/zypkg_controller.sh".
Starting to set up zy-pkgs environment ...
-> No volume exists now. zy-pkgs will not work.
sh: you need to specify whom to kill
Dec  4 09:21:01 (none) syslog-ng[1334]: Termination requested via signal, terminating;
Dec  4 09:21:01 (none) syslog-ng[1334]: syslog-ng shutting down; version='2.0.10'
rm: can't remove '/i-data/.system/dropbox/dropbox.enable': No such file or directory
mkdir: can't create directory '/i-data/.system/dropbox': No such file or directory
Dec  4 09:21:01 NSA325-v2 syslog-ng[2318]: syslog-ng starting up; version='2.0.10'
cp: can't create '/i-data/.system/dropbox/dropbox.db': No such file or directory
mkdir: can't create directory '/i-data/md0/.system/web_cache': No such file or directory
mount: special device /i-data/md0/.system/web_cache does not exist
chmod: /i-data/md0/.system/zyxelFrameworkLog: No such file or directory
chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
Web Server already started.
mkdir: can't create directory '/i-data/md0/': No such file or directory
mkdir: can't create directory '/i-data/md0/': No such file or directory
Starting app_wd...
 core_checksum : 3f68d24c4d30c56ef86dd0808f89ec72
 fwversion : V4.80(AALS.0)C0
 img_checksum : 24c99d7e5313ccefa42942ee2ef043d7
 modelid : AE03
 revision : 46871
 romfile_checksum : 6613
 zld_checksum : b56a608539da559b33d27781c58ab2a9
GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1

Update zypkg list
[2407] server write-only FIFO is opened (fd=6)
[2407] server read-only FIFO is opened (fd=7)
[2407] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 644
POLLHUP on 7
  pid = 2407
[2407] is disconnected
chmod: /i-data/md0/admin/zy-pkgs: No such file or directory
[2430] server write-only FIFO is opened (fd=6)
[2430] server read-only FIFO is opened (fd=7)
[2430] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 412
killall: twonkystarter: no process killed
/usr/lib/python2.6/site-packages/flickrapi/__init__.py:45: DeprecationWarning: the md5 module is deprecated; use hashlib instead
umount: /usr/local/apache/htdocs/adv,/res/imdb_poster: not mounted
Dec  4 09:21:08 NSA325-v2 zcip: config egiga0 169.254.157.149
Dec  4 09:21:08 NSA325-v2 zcip: script /usr/share/zcip.script config failed, exitcode=1
POLLHUP on 7
  pid = 2430
[2430] is disconnected
mdadm_status_log.sh: raid status = DeviceDisappeared
2462
led_state_map_addr = 46

Please press Enter to activate this console. mdadm_status_log.sh: raid mdx = /dev/md0
Dec  4 09:21:20 NSA325-v2 ntpdate[2047]: can't find host tock.usno.navy.mil
Dec  4 09:21:20 NSA325-v2 ntpdate[2047]: no servers can be used, exiting
Dec  4 09:21:32 NSA325-v2 dhcpcd[2485]: timed out waiting for a valid DHCP server response
Dec  4 09:21:42 NSA325-v2 ntpdate[2481]: can't find host ntp3.cs.wisc.edu
Dec  4 09:21:42 NSA325-v2 ntpdate[2481]: no servers can be used, exiting
egiga0: link up, full duplex, speed 100 Mbps
ADDRCONF(NETDEV_CHANGE): egiga0: link becomes ready
[2495] server write-only FIFO is opened (fd=6)
[2495] server read-only FIFO is opened (fd=7)
[2495] server error read-only FIFO is opened (fd=8)
argc = 3,  func = 106
argid[1]: 1087; argv[1]: ge1
argid[2]: 350; argv[2]: exit
POLLHUP on 7
  pid = 2495
[2495] is disconnected
[2500] server write-only FIFO is opened (fd=6)
[2500] server read-only FIFO is opened (fd=7)
[2500] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 445
POLLHUP on 7
  pid = 2500
[2500] is disconnected
[2505] server write-only FIFO is opened (fd=6)
[2505] server read-only FIFO is opened (fd=7)
[2505] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 446
argid[1]: 879; argv[1]: fetch
argid[2]: 632; argv[2]: auto
argid[3]: 1087; argv[3]: ge1
Dec  4 09:21:46 NSA325-v2 ntpdate[2519]: can't find host ntp.cs.strath.ac.uk
Dec  4 09:21:46 NSA325-v2 ntpdate[2519]: no servers can be used, exiting
/bin/rm -f /var/zyxel/zysh/egiga0.metric
Dec  4 09:21:55 NSA325-v2 ntpdate[2526]: can't find host ntp1.sp.se
Dec  4 09:21:55 NSA325-v2 ntpdate[2526]: no servers can be used, exiting
/bin/ip route del default via 0.0.0.0 dev egiga0
RTNETLINK answers: No such process
Dec  4 09:21:58 NSA325-v2 ntpdate[2539]: can't find host time1.stupi.se
Dec  4 09:21:58 NSA325-v2 ntpdate[2539]: no servers can be used, exiting
POLLHUP on 7
  pid = 2505
[2505] is disconnected
[2546] server write-only FIFO is opened (fd=6)
[2546] server read-only FIFO is opened (fd=7)
[2546] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 141
POLLHUP on 7
  pid = 2546
[2546] is disconnected
Dec  4 09:22:01 NSA325-v2 dhcpcd[2537]: timed out waiting for a valid DHCP server response
Dec  4 09:22:04 NSA325-v2 ntpdate[2574]: can't find host tick.stdtime.gov.tw
Dec  4 09:22:04 NSA325-v2 ntpdate[2574]: no servers can be used, exiting
Dec  4 09:22:09 NSA325-v2 ntpdate[2577]: can't find host tock.stdtime.gov.tw
Dec  4 09:22:09 NSA325-v2 ntpdate[2577]: no servers can be used, exiting
egiga0: link down
egiga0: link up, full duplex, speed 100 Mbps
[2601] server write-only FIFO is opened (fd=6)
[2601] server read-only FIFO is opened (fd=7)
[2601] server error read-only FIFO is opened (fd=8)
argc = 3,  func = 106
argid[1]: 1087; argv[1]: ge1
argid[2]: 350; argv[2]: exit
POLLHUP on 7
  pid = 2601
[2601] is disconnected
[2606] server write-only FIFO is opened (fd=6)
[2606] server read-only FIFO is opened (fd=7)
[2606] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 445
POLLHUP on 7
  pid = 2606
[2606] is disconnected
[2611] server write-only FIFO is opened (fd=6)
[2611] server read-only FIFO is opened (fd=7)
[2611] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 446
argid[1]: 879; argv[1]: fetch
argid[2]: 632; argv[2]: auto
argid[3]: 1087; argv[3]: ge1
/bin/rm -f /var/zyxel/zysh/egiga0.metric
/bin/ip route del default via 0.0.0.0 dev egiga0
POLLHUP on 7
  pid = 2611
[2611] is disconnected
[2638] server write-only FIFO is opened (fd=6)
[2638] server read-only FIFO is opened (fd=7)
[2638] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 141
POLLHUP on 7
  pid = 2638
[2638] is disconnected



BusyBox v1.17.2 (2015-05-15 11:23:13 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # Dec  4 01:22:36 NSA325-v2 linuxrc: starting pid 2468, tty '': '-/bin/sh'
Dec  4 09:22:37 NSA325-v2 dhcpcd[2632]: timed out waiting for a valid DHCP server response
/bi
/ # /bin/
-/bin/sh: /bin/: Permission denied
/ # ls
bin      etc      init     mnt      root     tmp      zyxel
dev      home     lib      proc     sbin     usr
e-data   i-data   linuxrc  ram_bin  sys      var
/ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
/ # 
/ # route 0.0.0.0 192.168.1.10[2677] server write-only FIFO is opened (fd=6)
[2677] server read-only FIFO is opened (fd=7)
[2677] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 70
POLLHUP on 7
  pid = 2677
[2677] is disconnected
[2682] server write-only FIFO is opened (fd=6)
[2682] server read-only FIFO is opened (fd=7)
[2682] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 71
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
./bin/ln -s -f /etc/MyZone /etc/localtime
Dec  4 09:23:01 NSA325-v2 zcip: init egiga0
POLLHUP on 7
  pid = 2682
[2682] is disconnected
Dec  4 09:23:01 NSA325-v2 zcip: start, interface egiga0
1[2695] server write-only FIFO is opened (fd=6)
[2695] server read-only FIFO is opened (fd=7)
[2695] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 349
POLLHUP on 7
  pid = 2695
[2695] is disconnected
[2720] server write-only FIFO is opened (fd=6)
[2720] server read-only FIFO is opened (fd=7)
[2720] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 349
POLLHUP on 7
  pid = 2720
[2720] is disconnected
[2725] server write-only FIFO is opened (fd=6)
[2725] server read-only FIFO is opened (fd=7)
[2725] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 346
argid[1]: 1224; argv[1]: ""
argid[2]: 597; argv[2]: in
argid[3]: 1225; argv[3]: "NULL"
POLLHUP on 7
  pid = 2725
[2725] is disconnected

BusyBox v1.17.2 (2015-05-15 11:23:13 CST) multi-call binary.

Usage: route [{add|del|delete}]

/ # 
/ # route 0.0.0.0 192.168.10.1
/ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         *               0.0.0.0         U     50     0        0 egiga0
/ # Dec  4 09:23:11 NSA325-v2 zcip: config egiga0 169.254.157.149
Dec  4 09:23:11 NSA325-v2 zcip: script /usr/share/zcip.script config failed, exitcode=1
cd /u
/ # cd /usr/sDec  4 09:23:21 NSA325-v2 ntpdate[2704]: can't find host time.stdtime.gov.tw
Dec  4 09:23:21 NSA325-v2 ntpdate[2704]: no servers can be used, exiting
h
/ # cd /usr/share/
/usr/share # ls
WordPress_patch_1.09.2.tgz  udhcpc
empty                       zcip.script
gallery_patch_1.09.2.tgz
/usr/share # cat zc
/usr/share # cat zcip.script 
#!/bin/sh

# only for use as a "zcip" callback script
if [ "x$interface" = x ]
then
	exit 1
fi

if [ -z $metric ]; then
	metric=10
fi

# zcip should start on boot/resume and various media changes
case "$1" in
init)
	# for now, zcip requires the link to be already up,
	# and it drops links when they go down.  that isn't
	# the most robust model...
	exit 0
	;;
config)
	if [ "x$ip" = x ]
	then
		exit 1
	fi
	# remember $ip for $interface, to use on restart
	if [ "x$IP" != x -a -w "$IP.$interface" ]
	then
		echo $ip > "$IP.$interface"
	fi
	ip address add dev $interface \
		scope global local "$ip/16" broadcast +
	exec route add default dev $interface metric $metric
	;;
deconfig)
	if [ x$ip = x ]
	then
		exit 1
	fi
	exec ip address del dev $interface local $ip
	;;
esac
exit 1
/usr/share # Dec  4 09:23:36 NSA325-v2 dhcpcd[2798]: timed out waiting for a valid DHCP server response
./z
/usr/share # ./zcip.script 
/usr/share # ls -la
drwxr-xr-x    4 root     root          1024 May 15  2015 .
drwxr-xr-x    8 root     root          1024 May 15  2015 ..
-rwxr-xr-x    1 root     root           929 May 15  2015 WordPress_patch_1.09.2.tgz
drwxr-xr-x    2 root     root          1024 May 15  2015 empty
-rwxr-xr-x    1 root     root          2038 May 15  2015 gallery_patch_1.09.2.tgz
drwxr-xr-x    2 root     root          1024 May 15  2015 udhcpc
-rwxr-xr-x    1 root     root           781 May 15  2015 zcip.script
/usr/share # ./u
/usr/share # ./udhcpc/
-/bin/sh: ./udhcpc/: Permission denied
/usr/share # cd u
/usr/share # cd udhcpc/
/usr/share/udhcpc # ls
default.script
/usr/share/udhcpc # ./d
/usr/share/udhcpc # ./default.script 
Error: should be called from udhcpc
/usr/share/udhcpc # cat de
/usr/share/udhcpc # cat default.script 
#!/bin/sh

# udhcpc script edited by Tim Riker <Tim@Rikers.org>

[ -z "$1" ] && echo "Error: should be called from udhcpc" && exit 1

RESOLV_CONF="/etc/resolv.conf"
[ -n "$broadcast" ] && BROADCAST="broadcast $broadcast"
[ -n "$subnet" ] && NETMASK="netmask $subnet"

case "$1" in
	deconfig)
		/sbin/ifconfig $interface 192.168.1.3
		;;

	renew|bound)
		/sbin/ifconfig $interface $ip $BROADCAST $NETMASK

		if [ -n "$router" ] ; then
			echo "deleting routers"
			while route del default dev $interface ; do
				:
			done

			metric=0
			for i in $router ; do
				route add default gw $i dev $interface metric $((metric++))
			done
		fi

		echo -n > $RESOLV_CONF
		[ -n "$domain" ] && echo search $domain >> $RESOLV_CONF
		for i in $dns ; do
			echo adding dns $i
			echo nameserver $i >> $RESOLV_CONF
		done
		;;
esac

exit 0
/usr/share/udhcpc # Dec  4 09:24:32 NSA325-v2 dhcpcd[2826]: timed out waiting for a valid DHCP server response

/usr/share/udhcpc # ifconfig egigia0 192.168.10.85 netmaksk 255.255.255.0
/usr/share/udhcpc # 
/usr/share/udhcpc # ifconfig egiga0 192.168.10.85 netmask 255.255.255.0
/usr/share/udhcpc # cat default.script ifconfig
egiga0    Link encap:Ethernet  HWaddr 00:50:43:00:02:02  
          inet addr:192.168.10.85  Bcast:192.168.10.255  Mask:255.255.255.0
          inet6 addr: fe80::250:43ff:fe00:202/64 Scope:Link
          UP BROADCAST NOTRAILERS RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532 
          RX bytes:0 (0.0 B)  TX bytes:6448 (6.2 KiB)
          Interrupt:11 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:34 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:6084 (5.9 KiB)  TX bytes:6084 (5.9 KiB)

/usr/share/udhcpc # ifconfig
egiga0    Link encap:Ethernet  HWaddr 00:50:43:00:02:02  
          inet addr:192.168.10.85  Bcast:192.168.10.255  Mask:255.255.255.0
          inet6 addr: fe80::250:43ff:fe00:202/64 Scope:Link
          UP BROADCAST NOTRAILERS RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532 
          RX bytes:0 (0.0 B)  TX bytes:6448 (6.2 KiB)
          Interrupt:11 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:35 errors:0 dropped:0 overruns:0 frame:0
          TX packets:35 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:6440 (6.2 KiB)  TX bytes:6440 (6.2 KiB)

/usr/share/udhcpc # 
/usr/share/udhcpc # ifconfig --help
BusyBox v1.17.2 (2015-05-15 11:23:13 CST) multi-call binary.

Usage: ifconfig [-a] interface [address]

/usr/share/udhcpc # ifconfig
egiga0    Link encap:Ethernet  HWaddr 00:50:43:00:02:02  
          inet addr:192.168.10.85  Bcast:192.168.10.255  Mask:255.255.255.0
          inet6 addr: fe80::250:43ff:fe00:202/64 Scope:Link
          UP BROADCAST NOTRAILERS RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:51 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532 
          RX bytes:0 (0.0 B)  TX bytes:8940 (8.7 KiB)
          Interrupt:11 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:36 errors:0 dropped:0 overruns:0 frame:0
          TX packets:36 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:6796 (6.6 KiB)  TX bytes:6796 (6.6 KiB)

/usr/share/udhcpc # Dec  4 09:25:28 NSA325-v2 dhcpcd[2847]: timed out waiting for a valid DHCP server response
ifconfig egiga0 inet6 down
ifconfig: bad address 'inet6'
/usr/share/udhcpc # 
/usr/share/udhcpc # ifconfig egiga0 inet6 down
ifconfig: bad address 'inet6'
/usr/share/udhcpc # egiga0: link down
exit

Please press Enter to activate this console. Dec  4 01:26:21 NSA325-v2 linuxrc: process '-/bin/sh' (pid 2468) exited. Scheduling for restart.



BusyBox v1.17.2 (2015-05-15 11:23:13 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # Dec  4 09:26:25 NSA325-v2 linuxrc: starting pid 2877, tty '': '-/bin/sh'
exit

Please press Enter to activate this console. Dec  4 09:26:27 NSA325-v2 linuxrc: process '-/bin/sh' (pid 2877) exited. Scheduling for restart.

Re: NSA 325 v2 bricked
January 15, 2017 04:40PM
buec65,

No, it is not that badlybricked. You are running stock FW on this NSA325v2. And perhaps something in your stock OS has been set erronously, so the OS is not completing the boot process.

If you like to install and run latest Linux kernel:
http://forum.doozan.com/read.php?2,12096

and latest u-boot:
http://forum.doozan.com/read.php?3,12381

Read these 2 threads and post questions if you are not sure.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: NSA 325 v2 bricked
January 27, 2017 09:55AM
with nandwrite mtd1 to mtd8 from other nsa325 written now problem

Any chance to recover?

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.01.27 15:52:30 =~=~=~=~=~=~=~=~=~=~=~=
ü
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: DB-88F6282A-BP LE 

U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz 

DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000   size 512MB 
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0xc80000.

Streaming disabled 
Write allocate disabled


USB 0: host mode
	[BlueDBG] reseting SoC Pex[0]  0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
	[BlueDBG] reseting SoC Pex[1]  0 ...
	[BlueDBG] reseting SoC Pex[1]  1 ...
	[BlueDBG] reseting SoC Pex[1]  2 ...
	[BlueDBG] reseting SoC Pex[1]  3 ...
	[BlueDBG] reseting SoC Pex[1]  4 ...
	[BlueDBG] reseting SoC Pex[1]  5 ...
	[BlueDBG] reseting SoC Pex[1]  6 ...
	[BlueDBG] reseting SoC Pex[1]  7 ...
	[BlueDBG] reseting SoC Pex[1]  8 ...
	[BlueDBG] reseting SoC Pex[1]  9 ...
	[BlueDBG] reseting SoC Pex[1]  10 ...
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  2  1  0 

NAND read: device 0 offset 0xc80000, size 0xa00000


Bad block at 0xc80000 in erase block from 0xc80000 will be skipped

Reading data from 0xca0000 --   0% complete.
Reading data from 0xcb9800 --   1% complete.
Reading data from 0xcd3000 --   2% complete.
Reading data from 0xcec800 --   3% complete.
Reading data from 0xd06000 --   4% complete.
Reading data from 0xd1f800 --   5% complete.
Reading data from 0xd39800 --   6% complete.
Reading data from 0xd53000 --   7% complete.
Reading data from 0xd6c800 --   8% complete.
Reading data from 0xd86000 --   9% complete.
Reading data from 0xd9f800 --  10% complete.
Reading data from 0xdb9800 --  11% complete.
Reading data from 0xdd3000 --  12% complete.
Reading data from 0xdec800 --  13% complete.
Reading data from 0xe06000 --  14% complete.
Reading data from 0xe1f800 --  15% complete.
Reading data from 0xe39800 --  16% complete.
Reading data from 0xe53000 --  17% complete.
Reading data from 0xe6c800 --  18% complete.
Reading data from 0xe86000 --  19% complete.
Reading data from 0xe9f800 --  20% complete.
Reading data from 0xeb9800 --  21% complete.
Reading data from 0xed3000 --  22% complete.
Reading data from 0xeec800 --  23% complete.
Reading data from 0xf06000 --  24% complete.
Reading data from 0xf1f800 --  25% complete.
Reading data from 0xf39800 --  26% complete.
Reading data from 0xf53000 --  27% complete.
Reading data from 0xf6c800 --  28% complete.
Reading data from 0xf86000 --  29% complete.
Reading data from 0xf9f800 --  30% complete.
Reading data from 0xfb9800 --  31% complete.
Reading data from 0xfd3000 --  32% complete.
Reading data from 0xfec800 --  33% complete.
Reading data from 0x1006000 --  34% complete.
Reading data from 0x101f800 --  35% complete.
Reading data from 0x1039800 --  36% complete.
Reading data from 0x1053000 --  37% complete.
Reading data from 0x106c800 --  38% complete.
Reading data from 0x1086000 --  39% complete.
Reading data from 0x109f800 --  40% complete.
Reading data from 0x10b9800 --  41% complete.
Reading data from 0x10d3000 --  42% complete.
Reading data from 0x10ec800 --  43% complete.
Reading data from 0x1106000 --  44% complete.
Reading data from 0x111f800 --  45% complete.
Reading data from 0x1139800 --  46% complete.
Reading data from 0x1153000 --  47% complete.
Reading data from 0x116c800 --  48% complete.
Reading data from 0x1186000 --  49% complete.
Reading data from 0x119f800 --  50% complete.
Reading data from 0x11b9800 --  51% complete.
Reading data from 0x11d3000 --  52% complete.
Reading data from 0x11ec800 --  53% complete.
Reading data from 0x1206000 --  54% complete.
Reading data from 0x121f800 --  55% complete.
Reading data from 0x1239800 --  56% complete.
Reading data from 0x1253000 --  57% complete.
Reading data from 0x126c800 --  58% complete.
Reading data from 0x1286000 --  59% complete.
Reading data from 0x129f800 --  60% complete.
Reading data from 0x12b9800 --  61% complete.
Reading data from 0x12d3000 --  62% complete.
Reading data from 0x12ec800 --  63% complete.
Reading data from 0x1306000 --  64% complete.
Reading data from 0x131f800 --  65% complete.
Reading data from 0x1339800 --  66% complete.
Reading data from 0x1353000 --  67% complete.
Reading data from 0x136c800 --  68% complete.
Reading data from 0x1386000 --  69% complete.
Reading data from 0x139f800 --  70% complete.
Reading data from 0x13b9800 --  71% complete.
Reading data from 0x13d3000 --  72% complete.
Reading data from 0x13ec800 --  73% complete.
Reading data from 0x1406000 --  74% complete.
Reading data from 0x141f800 --  75% complete.
Reading data from 0x1439800 --  76% complete.
Reading data from 0x1453000 --  77% complete.
Reading data from 0x146c800 --  78% complete.
Reading data from 0x1486000 --  79% complete.
Reading data from 0x149f800 --  80% complete.
Reading data from 0x14b9800 --  81% complete.
Reading data from 0x14d3000 --  82% complete.
Reading data from 0x14ec800 --  83% complete.
Reading data from 0x1506000 --  84% complete.
Reading data from 0x151f800 --  85% complete.
Reading data from 0x1539800 --  86% complete.
Reading data from 0x1553000 --  87% complete.
Reading data from 0x156c800 --  88% complete.
Reading data from 0x1586000 --  89% complete.
Reading data from 0x159f800 --  90% complete.
Reading data from 0x15b9800 --  91% complete.
Reading data from 0x15d3000 --  92% complete.
Reading data from 0x15ec800 --  93% complete.
Reading data from 0x1606000 --  94% complete.
Reading data from 0x161f800 --  95% complete.
Reading data from 0x1639800 --  96% complete.
Reading data from 0x1653000 --  97% complete.
Reading data from 0x166c800 --  98% complete.
Reading data from 0x1686000 --  99% complete.
Reading data from 0x169f800 -- 100% complete.
 10485760 bytes read: OK
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2016-01-26  10:49:44 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5796068 Bytes =  5.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................................................................................................................................................................ done, booting the kernel.

Linux version 2.6.31.8 (root@BuildMachine) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #2 Tue Jan 26 18:49:28 CST 2016
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 506752KB available (5360K code, 302K data, 2872K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
invoking softwareStaggeredSpinUp()..., it will delay 5 seconds to spin up the second harddisk

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB 
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
PEX1_MEM ....base e8000000, size 128MB 
PEX1_IO ....base f2100000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
NFLASH_CS ....base fa000000, size   2MB 
SPI_CS ....base f4000000, size  16MB 
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB 

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- DB-88F6282A-BP  Soc: MV88F6282 Rev 1 LE

 Detected Tclk 200000000 and SysClk 533333333 
Marvell USB EHCI Host controller #0: d003a740
	[BlueDBG] reseting SoC Pex[0]  0 ...
PEX0 interface detected Link X1
	[BlueDBG] reseting SoC Pex[1]  0 ...
	[BlueDBG] reseting SoC Pex[1]  1 ...
	[BlueDBG] reseting SoC Pex[1]  2 ...
	[BlueDBG] reseting SoC Pex[1]  3 ...
	[BlueDBG] reseting SoC Pex[1]  4 ...
	[BlueDBG] reseting SoC Pex[1]  5 ...
	[BlueDBG] reseting SoC Pex[1]  6 ...
	[BlueDBG] reseting SoC Pex[1]  7 ...
	[BlueDBG] reseting SoC Pex[1]  8 ...
	[BlueDBG] reseting SoC Pex[1]  9 ...
	[BlueDBG] reseting SoC Pex[1]  10 ...
PEX1 interface detected no Link.
pci 0000:00:01.0: PME# supported from D0 D3hot
pci 0000:00:01.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
gpio_dev = fd00000
LED_SET_CTL_IOC_NUM= 6702
High gpio polarity = 50 
High gpio polarity = 70 
Enable Interrupt
mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
mv88f6281_wdt: HW Watchdog timeout    = 15 sec.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 990
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
Wake up disk0......
Wake up disk1......
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
EnablePowerSaving 
PowerSavingTime = 15
No found HD
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 1 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Network Fast Processing (Routing) supported - (Disabled)
  o Driver ERROR statistics enabled
  o Proc tool API enabled
  o SKB Reuse supported - (Disabled)
  o SKB Recycle supported - (Disabled)
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
     o register under mv88fx_eth platform
     o eth0, ifindex = 2, GbE port = 0

mvFpRuleDb (d1090000): 16384 entries, 65536 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 100 at 0x000000c80000
Bad eraseblock 200 at 0x000001900000
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
rtc-pcf8563 0-0051: retrieved date/time is not valid.
rtc-pcf8563 0-0051: hctosys: invalid date/time
Freeing init memory: 2872K
*** Stage 1: Setup system and device drivers ***
usb 1-1: new high speed USB device using ehci_marvell and address 2
eth0: mac address changed
egiga0: started
ADDRCONF(NETDEV_UP): egiga0: link is not ready
rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
rtc-pcf8563 0-0051: retrieved date/time is not valid.
*** Stage 2: Prepare the root file system ***
Mount system partition...
yaffs: dev is 32505862 name is "mtdblock6" ro
yaffs: passed flags ""
ls: /zyxel/mnt/nand/sysdisk.img.gz: No such file or directory
NAND Flash Corrupt... 
Starting Pure-FTPd ...
/etc/init.d/rcS: line 205: /bin/pure-ftpd.official: not found
1 second...
2 second...
3 second...
4 second...
5 second...
6 second...
7 second...
8 second...
9 second...
10 second...

the sys-root image /dev/mtdblock6 is currupt !!
Dual images are currupt !!!
Starting Pure-FTPd ...
/etc/init.d/rcS: line 205: /bin/pure-ftpd.official: not found
1 second...
2 second...
usb 1-1: device descriptor read/64, error -110
3 second...
4 second...
5 second...
6 second...
7 second...
8 second...
9 second...
10 second...

bz time = 1f
bz status = 3
start buzzer

Please press Enter to activate this console. 


BusyBox v1.17.2 (2016-01-26 18:21:04 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # fw_printenvusb 1-1: device descriptor read/64, error -110
In hub_port_init, and number is 0, retry 0, port 1 .....
usb 1-1: new high speed USB device using ehci_marvell and address 3

bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=AE03
PRODUCT_NAME=NSA-325v2
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
ethaddr=28:28:5D:13:EC:0D
ethprime=egiga0
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
arcNumber=4495
ethact=egiga0
console=console=ttyS0,115200=mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
bootargs_root=root=/dev/nfs=rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
usb0Mode=host
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
disaMvPnp=no
enaAutoRecovery=yes
kernel_addr=0xc80000
pcieTune=no
pcieTune1=no
bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000
/ # halt
led_state_map_addr = 4e
Starting "/etc/init.d/zypkg_controller.sh".
Stopping all zypkgs via "/etc/init.d/zypkg_controller.sh" ...
- Failed: dependency file "/usr/local/zy-pkgs/etc/init.d/ZYPKG_DEPS" not exists.
/ # Starting "/etc/init.d/zypkg_controller.sh".
Starting to release zy-pkgs environment ...
umount: /usr/local/apache/htdocs/adv,/pkg: not found
umount: /etc/zyxel/zy-pkgs: not mounted
umount: /usr/local/zy-pkgs: not found
Finish "/etc/init.d/zypkg_controller.sh".
start kill.
 1107 root      2788 S    -/bin/sh

  1107 root      2788 S    -/bin/sh
usb 1-1: device descriptor read/64, error -110
BusyBox v1.17.2 (2016-01-26 18:21:04 CST) multi-call binary.

Usage: swapoff [-a] [DEVICE]

umount: /etc/zyxel: not mounted
rootfs / rootfs rw 0 0
/proc /proc proc rw,relatime 0 0
/sys /sys sysfs rw,relatime 0 0
none /proc/bus/usb usbfs rw,relatime 0 0
devpts /dev/pts devpts rw,relatime,mode=600 0 0
/dev/mtdblock6 /zyxel/mnt/nand yaffs2 ro,relatime 0 0

The system is going down NOW!

Sent SIGTERM to all processes

Sent SIGKILL to all processes

Requesting system halt
md: stopping all md devices.
Power down.
reg(3, 18) = 4985
reg(0, 18) = 0
reg(17, 16) = 4500
reg(17, 25) = 2828
reg(17, 24) = 135d
reg(17, 23) = dec
 
Re: NSA 325 v2 bricked
January 27, 2017 04:51PM
buec65,

Some of your NAND flash partitions were corrupted. And nandwrite will not fix them. If you don't really want to run newer kernel and u-boot, and just want to restore stock, you can find instruction at NAS Central:

http://zyxel.nas-central.org/wiki/Category:NSA-325

Basically, you will need to use a USB drive to reflash stock FW.

If that still does not work, then you will need to run new kernel that I posted above. After you can run new kernel and boot into Debian, you can restore stock FW from there.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner



Edited 1 time(s). Last edit at 01/27/2017 04:54PM by bodhi.
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: