Welcome! Log In Create A New Profile

Advanced

Using mSATA device on PogoPlug Pro

Posted by rayknight 
Using mSATA device on PogoPlug Pro
April 22, 2017 01:39AM
I have finally gotten around to trying to use the SATA to mSATA adapter on one of my PogoPlug Pros. I have been using this system with an eSATA drive successfully for over a year. I first used a USB to SATA adapter to connect the mSATA to SATA adapter with a SanDisk X300 MSATA 128GB SSD as /dev/sdb. I used fdisk to create the /dev/sdb1 partition and then formatted as ext3 with rootfs label and mounted as /media/usb0. I then ran rsync to sync the data from / to /media/usb0. To verify the copy I then removed the eSATA drive and booted again with the USB to SATA adapter. This boot was successful. I then disconnected the USB to SATA adapter and plugged the mSATA to SATA adapter directly to the SATA connector on the PogoPlug Pro. This resulted in the following issue:

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.
9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr
=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio
n cache
[    0.000000] Machine model: Pogoplug V3 Pro
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical
_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @c7eda000 s17696 r8192 d23264 u4915
2
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 116928K/131072K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 14144K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000166] Console: colour dummy device 80x30
[    0.000197] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.050017] pid_max: default: 32768 minimum: 301
[    0.050186] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.050204] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.051020] Initializing cgroup subsys net_cls
[    0.051102] CPU: Testing write buffer coherency: ok
[    0.051522] Setting up static identity map for 0x60008220 - 0x60008258
[    0.190131] Brought up 2 CPUs
[    0.190154] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.190942] devtmpfs: initialized
[    0.196119] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.196162] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.196472] prandom: seed boundary self test passed
[    0.200888] prandom: 100 self tests passed
[    0.200916] pinctrl core: initialized pinctrl subsystem
[    0.201743] NET: Registered protocol family 16
[    0.202301] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.230016] cpuidle: using governor ladder
[    0.260011] cpuidle: using governor menu
[    0.265290] gpio-oxnas 44000000.gpio: at address c8848000
[    0.265687] gpio-oxnas 44100000.gpio: at address c884a000
[    0.266275] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[    0.390064] oxnas-pcie 47c00000.pcie-controller: PCIe version/deviceID 0x82510b5
[    0.390184] oxnas-pcie 47c00000.pcie-controller: link up
[    0.390510] oxnas-pcie 47c00000.pcie-controller: PCI host bridge to bus 0000:00
[    0.390535] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[    0.390556] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[    0.390574] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff]
[    0.390594] pci_bus 0000:00: root bus resource [bus 00-7f]
[    0.391155] PCI: bus0: Fast back to back transfers disabled
[    0.391244] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x4800ffff]
[    0.391708] vgaarb: loaded
[    0.392202] SCSI subsystem initialized
[    0.393077] usbcore: registered new interface driver usbfs
[    0.393187] usbcore: registered new interface driver hub
[    0.393338] usbcore: registered new device driver usb
[    0.393546] pps_core: LinuxPPS API ver. 1 registered
[    0.393561] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.393605] PTP clock support registered
[    0.395786] clocksource: Switched to clocksource rps_clocksource_timer
[    0.414374] NET: Registered protocol family 2
[    0.415260] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.415303] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.415339] TCP: Hash tables configured (established 1024 bind 1024)
[    0.415439] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.415482] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.415746] NET: Registered protocol family 1
[    0.416281] RPC: Registered named UNIX socket transport module.
[    0.416302] RPC: Registered udp transport module.
[    0.416312] RPC: Registered tcp transport module.
[    0.416322] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.416716] Unpacking initramfs...
[    0.818803] Freeing initrd memory: 3764K (c7a7f000 - c7e2c000)
[    0.820528] Initialise system trusted keyring
[    0.852869] zbud: loaded
[    0.871400] NFS: Registering the id_resolver key type
[    0.871472] Key type id_resolver registered
[    0.871485] Key type id_legacy registered
[    0.871528] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.871552] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.872494] fuse init (API version 7.23)
[    0.874572] Key type big_key registered
[    0.964474] Key type asymmetric registered
[    0.964510] Asymmetric key parser 'x509' registered
[    0.964646] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.964672] io scheduler noop registered
[    0.964692] io scheduler deadline registered
[    0.964756] io scheduler cfq registered (default)
[    0.965409] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.966924] console [ttyS0] disabled
[    0.967022] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[    1.549816] console [ttyS0] enabled
[    1.564503] loop: module loaded
[    1.569605] scsi host0: sata_oxnas
[    1.573486] ata1: SATA max UDMA/133 irq 7
[    1.577569] sata_oxnas: resetting SATA core
[    1.578588] nand: Could not find valid ONFI parameter page; aborting
[    1.578629] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    1.578634] nand: Hynix NAND 128MiB 3,3V 8-bit
[    1.578644] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.578659] Scanning device for bad blocks
[    1.660935] 2 cmdlinepart partitions found on MTD device 41000000.nand
[    1.667440] Creating 2 MTD partitions on "41000000.nand":
[    1.672849] 0x000000000000-0x000000e00000 : "boot"
[    1.679559] 0x000000e00000-0x000008000000 : "data"
[    1.686845] oxnas-gmac 40400000.ethernet: no reset control found
[    1.692869] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    1.697891]  Ring mode enabled
[    1.700943]  DMA HW capability register supported
[    1.705448]  Enhanced/Alternate descriptors
[    1.709780]  Enabled extended descriptors
[    1.713779]  RX Checksum Offload Engine supported (type 2)
[    1.719232]  TX Checksum insertion supported
[    1.723486]  Wake-Up On Lan supported
[    1.727129]  Enable RX Mitigation via HW Watchdog Timer
[    1.748510] libphy: stmmac: probed
[    1.751964] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[    1.758379] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[    1.765104] PPP generic driver version 2.4.2
[    1.769786] rt2800pci 0000:00:00.0: enabling device (0140 -> 0142)
[    1.776153] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3213 detected
[    1.787386] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[    1.796523] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.803079] ehci-pci: EHCI PCI platform driver
[    1.807877] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    1.813434] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    1.821263] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[    1.840145] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    1.846456] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.853255] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.860464] usb usb1: Product: EHCI Host Controller
[    1.865318] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[    1.871741] usb usb1: SerialNumber: 40200100.ehci
[    1.877419] hub 1-0:1.0: USB hub found
[    1.881285] hub 1-0:1.0: 2 ports detected
[    1.886430] usbcore: registered new interface driver cdc_acm
[    1.892106] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.900216] usbcore: registered new interface driver cdc_wdm
[    1.906009] usbcore: registered new interface driver usb-storage
[    1.912220] usbcore: registered new interface driver usbserial
[    1.918110] usbcore: registered new interface driver usbserial_generic
[    1.924718] usbserial: USB Serial support registered for generic
[    1.931161] mousedev: PS/2 mouse device common for all mice
[    1.936890] i2c /dev entries driver
[    1.941788] hidraw: raw HID events driver (C) Jiri Kosina
[    1.947422] usbcore: registered new interface driver usbhid
[    1.953011] usbhid: USB HID core driver
[    1.958873] NET: Registered protocol family 10
[    1.980892] sit: IPv6 over IPv4 tunneling driver
[    1.986554] NET: Registered protocol family 17
[    1.991541] Key type dns_resolver registered
[    1.997122] registered taskstats version 1
[    2.001274] Loading compiled-in X.509 certificates
[    2.006167] zswap: loaded using pool lzo/zbud
[    2.025674] Key type encrypted registered
[    2.129999] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    2.136806] ata1.00: ATA-9: SanDisk X300 MSATA 128GB, X3520012, max UDMA/133
[    2.143869] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 0/32)
[    2.220134] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[    2.371911] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    2.378588] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.385725] usb 1-1: Product: USB2.0 Hub
[    2.390743] hub 1-1:1.0: USB hub found
[    2.394913] hub 1-1:1.0: 4 ports detected
[    2.680133] usb 1-1.4: new high-speed USB device number 3 using oxnas-ehci
[    2.792409] usb 1-1.4: New USB device found, idVendor=05e3, idProduct=0718
[    2.799262] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[    2.806568] usb 1-1.4: Product: USB Storage
[    2.810752] usb 1-1.4: SerialNumber: 000000000033
[    2.816604] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    2.823377] scsi host1: usb-storage 1-1.4:1.0
[    3.821539] scsi 1:0:0:0: Direct-Access     USB TO I DE/SATA Device   0041 PQ: 0 ANSI: 0
[    3.834109] sd 1:0:0:0: [sda] Test WP failed, assume Write Enabled
[    3.841730] sd 1:0:0:0: [sda] Asking for cache data failed
[    3.847203] sd 1:0:0:0: [sda] Assuming drive cache: write through
[    3.859356] sd 1:0:0:0: [sda] Attached SCSI disk
[   17.150005] ata1.00: qc timeout (cmd 0xef)
[   17.154088] sata_oxnas: resetting SATA core
[   17.510000] ata1.00: failed to set xfermode (err_mask=0x5)
[   18.020001] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   33.020008] ata1.00: qc timeout (cmd 0xef)
[   33.024087] sata_oxnas: resetting SATA core
[   33.380006] ata1.00: failed to set xfermode (err_mask=0x5)
[   33.385479] ata1.00: limiting speed to UDMA/133:PIO3
[   33.900003] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   48.900008] ata1.00: qc timeout (cmd 0xef)
[   48.904087] sata_oxnas: resetting SATA core
[   49.260011] ata1.00: failed to set xfermode (err_mask=0x5)
[   49.265477] ata1.00: disabled
[   49.268444] sata_oxnas: resetting SATA core
[   49.282869] ata1: exception Emask 0x10 SAct 0x0 SErr 0x20000 action 0xe frozen t4
[   49.290352] ata1: SError: { PHYInt }
[   49.293926] ata1: hard resetting link
[   50.200007] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   50.206799] ata1.00: ATA-9: SanDisk X300 MSATA 128GB, X3520012, max UDMA/133
[   50.213862] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 0/32)
[   65.220011] ata1.00: qc timeout (cmd 0xef)
[   65.224094] sata_oxnas: resetting SATA core
[   65.580019] ata1.00: failed to set xfermode (err_mask=0x5)
[   65.585495] ata1: hard resetting link
[   66.090007] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   81.090012] ata1.00: qc timeout (cmd 0xef)
[   81.094092] sata_oxnas: resetting SATA core
[   81.450014] ata1.00: failed to set xfermode (err_mask=0x5)
[   81.455488] ata1.00: limiting speed to UDMA/133:PIO3
[   81.460467] ata1: hard resetting link
[   81.970014] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   96.970017] ata1.00: qc timeout (cmd 0xef)
[   96.974097] sata_oxnas: resetting SATA core
[   97.330019] ata1.00: failed to set xfermode (err_mask=0x5)
[   97.335482] ata1.00: disabled
[   97.338449] sata_oxnas: resetting SATA core
[   97.352872] ata1: exception Emask 0x10 SAct 0x0 SErr 0x20000 action 0xe frozen t3
[   97.360368] ata1: SError: { PHYInt }
[   97.363944] ata1: hard resetting link
[   98.270018] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   98.276807] ata1.00: ATA-9: SanDisk X300 MSATA 128GB, X3520012, max UDMA/133
[   98.283868] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 0/32)
[  113.290022] ata1.00: qc timeout (cmd 0xef)
[  113.294103] sata_oxnas: resetting SATA core
[  113.650027] ata1.00: failed to set xfermode (err_mask=0x5)
[  113.655498] ata1: hard resetting link
[  114.160023] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  129.160028] ata1.00: qc timeout (cmd 0xef)
[  129.164106] sata_oxnas: resetting SATA core
[  129.520028] ata1.00: failed to set xfermode (err_mask=0x5)
[  129.525496] ata1.00: limiting speed to UDMA/133:PIO3
[  129.530475] ata1: hard resetting link
[  130.040023] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  145.040030] ata1.00: qc timeout (cmd 0xef)
[  145.044111] sata_oxnas: resetting SATA core
[  145.400033] ata1.00: failed to set xfermode (err_mask=0x5)
[  145.405496] ata1.00: disabled
[  145.408460] sata_oxnas: resetting SATA core
[  145.422894] ata1: exception Emask 0x10 SAct 0x0 SErr 0x20000 action 0xe frozen t2
[  145.430379] ata1: SError: { PHYInt }
[  145.433953] ata1: hard resetting link
[  146.340029] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  146.346810] ata1.00: ATA-9: SanDisk X300 MSATA 128GB, X3520012, max UDMA/133
[  146.353871] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 0/32)
[  161.360033] ata1.00: qc timeout (cmd 0xef)
[  161.364111] sata_oxnas: resetting SATA core
[  161.720035] ata1.00: failed to set xfermode (err_mask=0x5)
[  161.725509] ata1: hard resetting link
[  162.230036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  177.230039] ata1.00: qc timeout (cmd 0xef)
[  177.234117] sata_oxnas: resetting SATA core
[  177.590039] ata1.00: failed to set xfermode (err_mask=0x5)
[  177.595512] ata1.00: limiting speed to UDMA/133:PIO3
[  177.600488] ata1: hard resetting link
[  178.110033] ata1: SATA link up 1.5 Gbp

As can be seen in the above output the SATA core keeps resetting and getting a timeout.

I also have tried a Micron M550 64GB mSATA SSD with similar results. The only apparent difference is the Micron SSD prints the following line before the line identifying the Micron device:

[   50.236515] ata1.00: supports DRM functions and may not be fully accessible

For those who have successfully used an mSATA with the PogoPlug Pro what device did you use? I thought a SanDisk and/or a Micron would be a safe choice, but obviously its not.

Ray
Re: Using mSATA device on PogoPlug Pro
April 24, 2017 05:51PM
No response from anyone on this issue, but another data point from me. I was successful in using an older SanDisk 32GB MSATA SSD. Not sure why the larger SanDisk and the Micron cause timeout issues.
Re: Using mSATA device on PogoPlug Pro
April 24, 2017 07:02PM
Ray,

Cool! I'd like to add your mod to the Wiki. Please post:

- Brand and model.
- If you can post the pic of the card installed on the board, it would be nice.
- output of dmesg.

Later, if you get performance benchmarks, then add to the same post.

Thanks!

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Using mSATA device on PogoPlug Pro
April 25, 2017 10:36PM
This is the same mod that LeggoMyEggo posted about in Pogoplug Pro / V3 Internal SSD Mod. So it should already be in the wiki.

Ray
Re: Using mSATA device on PogoPlug Pro
April 25, 2017 11:11PM
rayknight Wrote:
-------------------------------------------------------
> This is the same mod that LeggoMyEggo posted about

Exactly the same mSATA card?

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Using mSATA device on PogoPlug Pro
April 25, 2017 11:35PM
I believe the one that actually worked is very close to what LeggoMyEggo has pictured. It is a SanDisk SDSA5DK-032G-1016 VER:10.56.00.

As stated above I also tried the following without success:
  • Sandisk X300 MSATA 128GB SD7SF6S-128G-1012 FW: X3300012
  • Micron M550 mSATA SSD 64GB SATA Model: MTFDDAT064MAY F/W: MU02

Ray
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: