U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
OX820 # bdinfo
arch_number = 0x00000480
boot_params = 0x60000100
DRAM bank   = 0x00000000
-> start    = 0x60000000
-> size     = 0x08000000
eth0name    = mii0
ethaddr     = 74:F0:6D:6A:1D:17
current eth = mii0
ip_addr     = 10.0.0.71
baudrate    = 115200 bps
TLB addr    = 0x67FF0000
relocaddr   = 0x67F2D000
reloc off   = 0x03F2D000
irq_sp      = 0x67E2CF48
sp start    = 0x67E2CF38
OX820 #

Stage-1 Bootloader Thu Jun  3 10:29:14 PDT 2010
Attempting to set PLLA to 700MHz ...
  plla_ctrl0 : 0x00000118
  plla_ctrl1 : 0x00380000
  plla_ctrl2 : 0x006F00D0
  plla_ctrl3 : 0x000000B0
PLLA Set

Setup memory, testing
Reading NAND, Image 0
Failed to correct error
  Hdr len: 0x0001AB60
  Hdr CRC: 0xE0B0E526
 read failed
Reading NAND, Image 1
  Hdr len: 0x0001AB60
  Hdr CRC: 0xE0B0E526
 OK


U-Boot 1.1.2 (Mar  2 2011 - 10:17:22)

U-Boot code: 60D00000 -> 60D1AB60  BSS: -> 60D1F218
RAM Configuration:
        Bank #0: 60000000 128 MB
SRAM Configuration:
        64KB at 0x50000000
NAND:256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0
$ bdinfo
arch_number = 0x00000480
env_t       = 0x00000000
boot_params = 0x60000100
DRAM bank   = 0x00000000
-> start    = 0x60000000
-> size     = 0x08000000
ethaddr     = 00:30:E0:00:00:01
ip_addr     = 192.168.50.100
baudrate    = 115200 bps
$

bdinfo

Quote

Openwrt does not find it. I'm loading with sata, there is no mdX on sata

bdinfo

/dev/mtd2 0x0 0x2000 0x2000 1

root @ OpenWrt: / # fw_printenv
Предупреждение: неверный CRC, используется среда по умолчанию
bootcmd = ВООТР; setenv bootargs root = / dev / nfs nfsroot = $ {serverip}: $ {rootpath} ip = $ {ipaddr}: $ {serverip}: $ {gatewayip}: $ {netmask}: $ {hostname} :: off; bootm
BootDelay = 5
боды = 115200

Quote
For now, you can work around this by specifying the MAC address inside /etc/network/interfaces.

	option macaddr '2A:C0:XX:XX:XX:XX'

Quote
After you rebuilt kernel and DTB, and then copy the files you should use "cp -a"

-rw-r--r--    1 root     root          8996 May 31 00:13 ox820-pogoplug-classic.dtb

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
OX820 # printenv
SET_dtb=fdt addr ${fdtaddr} ; fdt header
autoload=no
baudrate=115200
bootargs=root=LABEL=rootfs root=/dev/sda2
bootcmd=run ideboot
bootdelay=3
bootnew=bootm 60000000 - 61000000
bootold=bootm 60000000
console=console=ttyS0,115200n8
ethact=mii0
ethaddr=74:F0:6D:6A:1D:17
ext4_dtb=ext4load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb
ext4_ideboot=run ext4_uimage ; run ext4_dtb ; run SET_dtb ; run bootnew
ext4_uimage=ext4load ide 0:2 60000000 /boot/uImage
ext4_uinitrd=ext4load ide 0:2 0x60e00000 /boot/uInitrd
fdtaddr=61000000
filesize=2316
ideboot=run ext4_ideboot
idebootold=${loadold} ;${bootold}
imgaddr=60000000
ipaddr=10.0.0.71
keypressed=1
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
netcon=echo switch to net console;setenv stderr nc;setenv stdin nc;setenv stdout nc;echo switch to net console
preboot=run safeboot
serialcon=echo switch to serial console;setenv stderr serial;setenv stdin serial;setenv stdout serial;echo switch to serial console
stderr=serial
stdin=serial
stdout=serial
updboot=bootp;tftp 60000000 u-boot.img;ide write 60000000 400 400

Environment size: 1167/16380 bytes
OX820 # boot
3765068 bytes read in 598 ms (6 MiB/s)
8996 bytes read in 56 ms (156.3 KiB/s)
magic:                  0xd00dfeed
totalsize:              0x2324 (8996)
off_dt_struct:          0x38
off_dt_strings:         0x1fd8
off_mem_rsvmap:         0x28
version:                17
last_comp_version:      16
boot_cpuid_phys:        0x0
size_dt_strings:        0x34c
size_dt_struct:         0x1fa0
number mem_rsv:         0x0

## Booting kernel from Legacy Image at 60000000 ...
   Image Name:   ARM OpenWrt Linux-5.4.42
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3765004 Bytes = 3.6 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
   Booting using the fdt blob at 0x61000000
   Loading Kernel Image ... OK
   Loading Device Tree to 67e26000, end 67e2b323 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.42 (admin@runtu) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13374-2b92ee3)) #0 SMP Wed May 27 22:48:39 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 3
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x64000000
[    0.000000] percpu: Embedded 15 pages/cpu s29644 r8192 d23604 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: earlyprintk console=ttyS0,115200 root=/dev/sda2 rootfstype=ext4
[    0.000000] Bootloader command line not present
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 54360K/131072K available (6144K kernel code, 169K rwdata, 1372K rodata, 1024K init, 210K bss, 11176K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x2c0/0x4ec with crng_init=0
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000069] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000081] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000104] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000266] GIC: PPI13 is secure or misconfigured
[    0.000317] GIC: PPI13 is secure or misconfigured
[    0.000401] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.050416] pid_max: default: 32768 minimum: 301
[    0.050682] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.050705] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.052008] CPU: Testing write buffer coherency: ok
[    0.053757] Setting up static identity map for 0x60100000 - 0x6010005c
[    0.054010] rcu: Hierarchical SRCU implementation.
[    0.054635] smp: Bringing up secondary CPUs ...
[    0.055587] GIC: PPI13 is secure or misconfigured
[    0.110658] smp: Brought up 1 node, 2 CPUs
[    0.110689] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[    0.115425] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.115458] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.121812] pinctrl core: initialized pinctrl subsystem
[    0.122659] NET: Registered protocol family 16
[    0.126807] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.129100] cpuidle: using governor menu
[    0.129228] No ATAGs?
[    0.154078] SCSI subsystem initialized
[    0.154739] pps_core: LinuxPPS API ver. 1 registered
[    0.154752] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.154795] PTP clock support registered
[    0.155880] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.157199] thermal_sys: Registered thermal governor 'step_wise'
[    0.157557] NET: Registered protocol family 2
[    0.158320] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.158394] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.158428] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.158464] TCP: Hash tables configured (established 1024 bind 1024)
[    0.158615] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.158663] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.159057] NET: Registered protocol family 1
[    0.159111] PCI: CLS 0 bytes, default 32
[    0.160878] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.172800] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.175767] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.177702] printk: console [ttyS0] disabled
[    0.177858] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    0.609131] printk: console [ttyS0] enabled
[    0.629224] brd: module loaded
[    0.642488] loop: module loaded
[    0.647498] scsi host0: sata_oxnas
[    0.651427] ata1: SATA max UDMA/133 irq 57
[    0.656056] sata_oxnas: resetting SATA core
[    0.726182] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    0.734830] ONFI parameter recovery failed, aborting
[    0.739829] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    0.746191] nand: Hynix NAND 256MiB 3,3V 8-bit
[    0.750620] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.758192] Scanning device for bad blocks
[    0.788815] Bad eraseblock 324 at 0x000002880000
[    0.793451] Bad eraseblock 325 at 0x0000028a0000
[    0.938874] 5 fixed-partitions partitions found on MTD device 41000000.nand-controller
[    0.946787] Creating 5 MTD partitions on "41000000.nand-controller":
[    0.953118] 0x000000000000-0x000000040000 : "stage1"
[    0.959682] 0x000000040000-0x0000003c0000 : "u-boot"
[    0.966231] 0x0000003c0000-0x000000440000 : "u-boot-env"
[    0.973184] 0x000000440000-0x000000e00000 : "kernel"
[    0.979840] 0x000000e00000-0x000008000000 : "ubi"
[    0.987205] libphy: Fixed MDIO Bus: probed
[    0.992092] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[    0.998254] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    1.004067] oxnas-dwmac 40400000.ethernet: no reset control found
[    1.076264] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[    1.083212] oxnas-dwmac 40400000.ethernet:   DWMAC1000
[    1.088302] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    1.095577] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    1.102881] oxnas-dwmac 40400000.ethernet: COE Type 2
[    1.107939] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    1.114777] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    1.121095] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    1.127918] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    1.134499] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    1.140170] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.148014] oxnas-dwmac 40400000.ethernet: device MAC address ea:f8:07:b9:18:8f
[    1.165360] libphy: stmmac: probed
[    1.165931] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    1.168821] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.187604] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    1.202442] ledtrig-cpu: registered to indicate activity on CPUs
[    1.210076] NET: Registered protocol family 10
[    1.216166] Segment Routing with IPv6
[    1.219911] NET: Registered protocol family 17
[    1.230586] UBI error: no valid UBI magic found inside mtd4
[    1.236275] ata1.00: HPA detected: current 156299375, native 156301488
[    1.242808] ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
[    1.242818] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    1.291312] ata1.00: configured for UDMA/133
[    1.296312] scsi 0:0:0:0: Direct-Access     ATA      ST380815AS       C    PQ: 0 ANSI: 5
[    1.305681] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.306401] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    1.318822] sd 0:0:0:0: [sda] Write Protect is off
[    1.323822] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.356372]  sda: sda1 sda2 sda3
[    1.362055] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.373265] EXT4-fs (sda2): INFO: recovery required on readonly filesystem
[    1.380183] EXT4-fs (sda2): write access will be enabled during recovery
[    1.451210] EXT4-fs (sda2): recovery complete
[    1.489318] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[    1.497098] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[    1.505231] Freeing unused kernel memory: 1024K
[    1.510064] Run /sbin/init as init process
[    1.664350] init: Console is alive
[    1.771845] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    1.804848] usbcore: registered new interface driver usbfs
[    1.810485] usbcore: registered new interface driver hub
[    1.815987] usbcore: registered new device driver usb
[    1.822830] Button Hotplug driver version 0.4.1
[    1.830310] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.838604] ehci-fsl: Freescale EHCI Host controller driver
[    1.845294] ehci-platform: EHCI generic platform driver
[    2.055910] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    2.061424] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    2.069708] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    2.095930] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    2.103086] hub 1-0:1.0: USB hub found
[    2.107000] hub 1-0:1.0: 2 ports detected
[    2.116805] usbcore: registered new interface driver usb-storage
[    2.124011] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.133550] init: - preinit -
[    2.532254] random: jshn: uninitialized urandom read (4 bytes read)
[    2.577464] random: jshn: uninitialized urandom read (4 bytes read)
[    2.613939] random: jshn: uninitialized urandom read (4 bytes read)
[    2.647680] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211DN Gigabit Ethernet]
[    2.658734] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found
[    2.666193] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    2.674785] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[    2.681208] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.872314] mount_root: mounting /dev/root
[    6.886492] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    6.894924] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    6.895326] EXT4-fs (sda2): re-mounted. Opts: (null)
[    6.906529] mount_root: loading kmods from internal overlay
[    6.937077] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    6.946757] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    7.506186] block: attempting to load /etc/config/fstab
[    7.523947] block: extroot: not configured
[    7.531632] urandom-seed: Seeding with /etc/urandom.seed
[    7.582259] oxnas-dwmac 40400000.ethernet eth0: Link is Down
[    7.598848] procd: - early -
[    7.827484] urandom_read: 1 callbacks suppressed
[    7.827496] random: jshn: uninitialized urandom read (4 bytes read)
[    8.166054] procd: - ubus -
[    8.229437] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.236610] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.244587] procd: - init -
Please press Enter to activate this console.
[    8.854586] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.867261] urngd: v1.0.2 started.
[    8.970368] videodev: Linux video capture interface: v2.00
[    9.014858] usbcore: registered new interface driver ums-alauda
[    9.022648] random: crng init done
[    9.022735] usbcore: registered new interface driver ums-cypress
[    9.026127] random: 3 urandom warning(s) missed due to ratelimiting
[    9.042465] usbcore: registered new interface driver ums-datafab
[    9.050429] usbcore: registered new interface driver ums-freecom
[    9.063265] usbcore: registered new interface driver ums-isd200
[    9.087467] usbcore: registered new interface driver ums-jumpshot
[    9.095444] usbcore: registered new interface driver ums-karma
[    9.113167] usbcore: registered new interface driver ums-sddr09
[    9.132769] usbcore: registered new interface driver ums-sddr55
[    9.142036] usbcore: registered new interface driver ums-usbat
[    9.203207] xt_time: kernel timezone is -0000
[    9.267576] usbcore: registered new interface driver uvcvideo
[    9.273305] USB Video Class driver (1.1.1)
[    9.310671] kmodloader: done loading kernel modules from /etc/modules.d/*
[   13.253524] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211DN Gigabit Ethernet]
[   13.306042] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found
[   13.313428] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   13.322063] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[   13.328448] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode
[   13.344143] br-lan: port 1(eth0) entered blocking state
[   13.349460] br-lan: port 1(eth0) entered disabled state
[   13.355013] device eth0 entered promiscuous mode
[   17.526458] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   17.534899] br-lan: port 1(eth0) entered blocking state
[   17.540180] br-lan: port 1(eth0) entered forwarding state
[   17.547248] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.31.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r13374-2b92ee3
 -----------------------------------------------------
root@OpenWrt:/# fw_printenv
Warning: Bad CRC, using default environment
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=5
baudrate=115200
root@OpenWrt:/# ls -lart /boot
-rw-r--r--    1 root     root      15554100 May 31 00:13 uInitrd
-rw-r--r--    1 root     root       3765068 May 31 00:13 uImage
drwxr-xr-x    2 root     root          4096 May 31 00:13 dts
drwxrwxr-x   18 root     root          4096 May 31 00:13 ..
drwxr-xr-x    3 root     root          4096 May 31 00:13 .
root@OpenWrt:/# ls -lart /boot/dts
-rw-r--r--    1 root     root          8996 May 31 00:13 ox820-pogoplug-classic.dtb
drwxr-xr-x    3 root     root          4096 May 31 00:13 ..
drwxr-xr-x    2 root     root          4096 May 31 00:13 .
root@OpenWrt:/#

printenv
boot

fw_printenv
ls -lart /boot
ls -lart /boot/dts

printenv ethaddr

setenv ethaddr xxxxx

--- a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts	2020-05-30 03:19:08.975612000 +0300
+++ b/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts	2020-05-30 18:19:58.000000000 +0300
@@ -24,6 +24,7 @@
 	};
 
 	aliases {
+		ethernet0 = &etha;
 		serial0 = &uart0;
 		gpio0 = &gpio0;
 		gpio1 = &gpio1;

diff -Naur --no-dereference a/arch/arm/boot/dts/ox820-pogoplug-classic.dts b/arch/arm/boot/dts/ox820-pogoplug-classic.dts

.......

+       aliases {
+               ethernet0 = &etha;
+               serial0 = &uart0;
+               gpio0 = &gpio0;
+               gpio1 = &gpio1;
+       };

Quote
The new DTBs fix the SATA problem with Pogo Pro, and also enable the kernel to use the MAC address passed by u-boot to bring up network (fixed the problem with the MAC address generated randomly by the kernel)

--- a/arch/arm/boot/dts/ox820.dtsi	2020-05-29 22:26:20.216313000 +0300
+++ b/arch/arm/boot/dts/ox820.dtsi	2020-05-30 02:15:29.045576000 +0300
@@ -93,7 +93,6 @@
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq", "eth_wake_irq";
-			mac-address = [000000000000]; /* Filled in by U-Boot */
 			phy-mode = "rgmii";
 
 			clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>;

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
3754342 bytes read in 599 ms (6 MiB/s)
6130758 bytes read in 947 ms (6.2 MiB/s)
8982 bytes read in 48 ms (182.6 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   ARM OpenWrt Linux-5.4.42
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3754278 Bytes = 3.6 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   ARM OpenWrt Linux-5.4.42
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6130694 Bytes = 5.8 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
No Linux ARM Ramdisk Image
Ramdisk image is corrupt or invalid
OX820 # printenv
SET_dtb=fdt addr ${fdtaddr} ; fdt header
autoload=no
baudrate=115200
bootargs=root=LABEL=rootfs root=/dev/sda2
bootcmd=run ideboot
bootdelay=3
bootnew=bootm 60000000 - 61000000
bootold=bootm 60000000
console=console=ttyS0,115200n8
ethact=mii0
ethaddr=74:F0:6D:6A:1D:17
ext4_dtb=ext4load ide 0:2 0x62c00000 /boot/dts/ox820-pogoplug-classic.dtb
ext4_ideboot=run ext4_uimage ; run ext4_uinitrd; run ext4_dtb; bootm 0x60500000 0x60e00000 0x62c00000
ext4_uimage=ext4load ide 0:2 0x60500000 /boot/uImage
ext4_uinitrd=ext4load ide 0:2 0x60e00000 /boot/uInitrd
fdtaddr=61000000
filesize=2316
ideboot=run ext4_ideboot
idebootold=${loadold} ;${bootold}
imgaddr=60000000
ipaddr=10.0.0.71
keypressed=1
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
netcon=echo switch to net console;setenv stderr nc;setenv stdin nc;setenv stdout nc;echo switch to net console
preboot=run safeboot
serialcon=echo switch to serial console;setenv stderr serial;setenv stdin serial;setenv stdout serial;echo switch to serial console
stderr=serial
stdin=serial
stdout=serial
updboot=bootp;tftp 60000000 u-boot.img;ide write 60000000 400 400

Environment size: 1201/16380 bytes
OX820 #

setenv ext4_ideboot 'run ext4_uimage ; run ext4_dtb ; run SET_dtb ; run bootnew'
setenv ext4_uimage 'ext4load ide 0:2 60000000 /boot/uImage'
setenv ext4_dtb 'ext4load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb'

git clone https://git.openwrt.org/openwrt/openwrt.git Openwrt-snapshot-5.4

		bootargs= "earlyprintk console=ttyS0,115200 root=/dev/sda2 rootfstype=ext4";

LABEL=rootfs    /               ext4    noatime,errors=remount-ro 0 1

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
3754342 bytes read in 607 ms (5.9 MiB/s)
8982 bytes read in 47 ms (186.5 KiB/s)
magic:                  0xd00dfeed
totalsize:              0x2316 (8982)
off_dt_struct:          0x38
off_dt_strings:         0x1fc8
off_mem_rsvmap:         0x28
version:                17
last_comp_version:      16
boot_cpuid_phys:        0x0
size_dt_strings:        0x34e
size_dt_struct:         0x1f90
number mem_rsv:         0x0

## Booting kernel from Legacy Image at 60000000 ...
   Image Name:   ARM OpenWrt Linux-5.4.42
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3754278 Bytes = 3.6 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
   Booting using the fdt blob at 0x61000000
   Loading Kernel Image ... OK
   Loading Device Tree to 67e26000, end 67e2b315 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.42 (admin@runtu) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13374-2b92ee3)) #0 SMP Wed May 27 22:48:39 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 3
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x64000000
[    0.000000] percpu: Embedded 15 pages/cpu s29644 r8192 d23604 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: earlyprintk console=ttyS0,115200 root=/dev/sda2 rootfstype=ext4
[    0.000000] Bootloader command line not present
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 54368K/131072K available (6144K kernel code, 169K rwdata, 1364K rodata, 1024K init, 208K bss, 11168K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x2c0/0x4ec with crng_init=0
[    0.000020] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000066] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000081] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000102] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000258] GIC: PPI13 is secure or misconfigured
[    0.000307] GIC: PPI13 is secure or misconfigured
[    0.000394] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.050403] pid_max: default: 32768 minimum: 301
[    0.050711] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.050731] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.052032] CPU: Testing write buffer coherency: ok
[    0.053821] Setting up static identity map for 0x60100000 - 0x6010005c
[    0.054085] rcu: Hierarchical SRCU implementation.
[    0.054714] smp: Bringing up secondary CPUs ...
[    0.055677] GIC: PPI13 is secure or misconfigured
[    0.110650] smp: Brought up 1 node, 2 CPUs
[    0.110681] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[    0.115955] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.115988] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.122257] pinctrl core: initialized pinctrl subsystem
[    0.123005] NET: Registered protocol family 16
[    0.127155] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.129246] cpuidle: using governor menu
[    0.129379] No ATAGs?
[    0.154393] SCSI subsystem initialized
[    0.155046] pps_core: LinuxPPS API ver. 1 registered
[    0.155061] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.155097] PTP clock support registered
[    0.156200] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.157591] thermal_sys: Registered thermal governor 'step_wise'
[    0.157964] NET: Registered protocol family 2
[    0.158755] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.158827] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.158863] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.158899] TCP: Hash tables configured (established 1024 bind 1024)
[    0.159057] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.159111] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.159503] NET: Registered protocol family 1
[    0.159554] PCI: CLS 0 bytes, default 32
[    0.161292] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.173181] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.176552] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.178140] printk: console [ttyS0] disabled
[    0.178293] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    0.609538] printk: console [ttyS0] enabled
[    0.629383] brd: module loaded
[    0.642900] loop: module loaded
[    0.647923] scsi host0: sata_oxnas
[    0.651837] ata1: SATA max UDMA/133 irq 57
[    0.656360] sata_oxnas: resetting SATA core
[    0.726507] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    0.735157] ONFI parameter recovery failed, aborting
[    0.740154] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    0.746516] nand: Hynix NAND 256MiB 3,3V 8-bit
[    0.750945] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.758520] Scanning device for bad blocks
[    0.789184] Bad eraseblock 324 at 0x000002880000
[    0.793820] Bad eraseblock 325 at 0x0000028a0000
[    0.939107] 5 fixed-partitions partitions found on MTD device 41000000.nand-controller
[    0.947020] Creating 5 MTD partitions on "41000000.nand-controller":
[    0.953349] 0x000000000000-0x000000040000 : "stage1"
[    0.959874] 0x000000040000-0x0000003c0000 : "u-boot"
[    0.966517] 0x0000003c0000-0x000000440000 : "u-boot-env"
[    0.973345] 0x000000440000-0x000000e00000 : "kernel"
[    0.980021] 0x000000e00000-0x000008000000 : "ubi"
[    0.987384] libphy: Fixed MDIO Bus: probed
[    0.992256] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[    0.998425] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    1.004239] oxnas-dwmac 40400000.ethernet: no reset control found
[    1.076579] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[    1.083525] oxnas-dwmac 40400000.ethernet:   DWMAC1000
[    1.088611] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    1.095887] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    1.103196] oxnas-dwmac 40400000.ethernet: COE Type 2
[    1.108249] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    1.115092] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    1.121400] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    1.128217] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    1.134799] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    1.140469] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.148308] oxnas-dwmac 40400000.ethernet: device MAC address 5e:46:c2:b0:d4:82
[    1.165698] libphy: stmmac: probed
[    1.166251] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    1.169164] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.187947] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    1.202703] ledtrig-cpu: registered to indicate activity on CPUs
[    1.210416] NET: Registered protocol family 10
[    1.216504] Segment Routing with IPv6
[    1.220252] NET: Registered protocol family 17
[    1.230978] UBI error: no valid UBI magic found inside mtd4
[    1.238389] ata1.00: HPA detected: current 156299375, native 156301488
[    1.244904] ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
[    1.250506] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    1.296721] ata1.00: configured for UDMA/133
[    1.301644] scsi 0:0:0:0: Direct-Access     ATA      ST380815AS       C    PQ: 0 ANSI: 5
[    1.311121] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.311726] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    1.324272] sd 0:0:0:0: [sda] Write Protect is off
[    1.329341] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.361781]  sda: sda1 sda2 sda3
[    1.367667] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.397363] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[    1.405063] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[    1.413314] Freeing unused kernel memory: 1024K
[    1.436456] Run /sbin/init as init process
[    1.614824] init: Console is alive
[    1.642490] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    1.674007] usbcore: registered new interface driver usbfs
[    1.679646] usbcore: registered new interface driver hub
[    1.685058] usbcore: registered new device driver usb
[    1.691916] Button Hotplug driver version 0.4.1
[    1.699399] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.710981] ehci-fsl: Freescale EHCI Host controller driver
[    1.717785] ehci-platform: EHCI generic platform driver
[    1.936225] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    1.941736] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    1.950013] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    1.976220] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    1.983301] hub 1-0:1.0: USB hub found
[    1.987215] hub 1-0:1.0: 2 ports detected
[    1.995148] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.013352] init: - preinit -
[    2.407692] random: jshn: uninitialized urandom read (4 bytes read)
[    2.452428] random: jshn: uninitialized urandom read (4 bytes read)
[    2.488204] random: jshn: uninitialized urandom read (4 bytes read)
[    2.521262] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211DN Gigabit Ethernet]
[    2.532267] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found
[    2.539729] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    2.548375] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[    2.554718] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.752483] mount_root: mounting /dev/root
[    6.775790] EXT4-fs (sda2): re-mounted. Opts: (null)
[    6.781122] mount_root: loading kmods from internal overlay
[    6.798865] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    6.808153] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    7.369858] block: attempting to load /etc/config/fstab
[    7.400844] block: extroot: not configured
[    7.408488] urandom-seed: Seeding with /etc/urandom.seed
[    7.481310] procd: - early -
[    8.046589] procd: - ubus -
[    8.214054] urandom_read: 1 callbacks suppressed
[    8.214067] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.225707] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.232291] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.240145] procd: - init -
Please press Enter to activate this console.
[    8.871971] urngd: v1.0.2 started.
[    8.927398] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.984870] random: crng init done
[    8.988331] random: 3 urandom warning(s) missed due to ratelimiting
[    8.996247] kmodloader: done loading kernel modules from /etc/modules.d/*
[   12.226414] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211DN Gigabit Ethernet]
[   12.256307] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found
[   12.263782] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   12.272460] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[   12.278865] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode
[   12.297850] br-lan: port 1(eth0) entered blocking state
[   12.303088] br-lan: port 1(eth0) entered disabled state
[   12.308825] device eth0 entered promiscuous mode
[   16.486766] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   16.495211] br-lan: port 1(eth0) entered blocking state
[   16.500495] br-lan: port 1(eth0) entered forwarding state
[   16.507558] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.31.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r13374-2b92ee3
 -----------------------------------------------------
root@OpenWrt:/#

## Booting kernel from Legacy Image at 60000000 ...
   Image Name:   Linux-4.14.180-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4600384 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
   Booting using the fdt blob at 0x61000000
   Loading Kernel Image ... OK
   Loading Device Tree to 67e26000, end 67e2b2bb ... OK

setenv ext4_ideboot 'run ext4_uimage ; run ext4_uinitrd; run ext4_dtb; bootm 0x60500000 0x60e00000 0x62c00000'
setenv ext4_uimage 'ext4load ide 0:2 0x60500000 /boot/uImage'
setenv ext4_uinitrd 'ext4load ide 0:2 0x60e00000 /boot/uInitrd
setenv ext4_dtb 'ext4load ide 0:2 0x62c00000 /boot/dts/ox820-pogoplug-classic.dtb'

boot

LABEL=rootfs    /               ext4    noatime,errors=remount-ro 0 1

LABEL=rootfs /     # so on with whatever  remained in this line

setenv bootargs 'root=LABEL=rootfs mtdparts=41000000.nand:14m(boot),-(ubi) earlyprintk=serial'

e2label /dev/sda2 rootfs

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
OX820 # setenv bootargs 'root=LABEL=rootfs mtdparts=41000000.nand:14m(boot),-(ubi) earlyprintk=serial'
OX820 # printenv bootargs
bootargs=root=LABEL=rootfs mtdparts=41000000.nand:14m(boot),-(ubi) earlyprintk=serial
OX820 # boot
4600448 bytes read in 723 ms (6.1 MiB/s)
8892 bytes read in 40 ms (216.8 KiB/s)
magic:                  0xd00dfeed
totalsize:              0x22bc (8892)
off_dt_struct:          0x38
off_dt_strings:         0x1f98
off_mem_rsvmap:         0x28
version:                17
last_comp_version:      16
boot_cpuid_phys:        0x0
size_dt_strings:        0x324
size_dt_struct:         0x1f60
number mem_rsv:         0x0

## Booting kernel from Legacy Image at 60000000 ...
   Image Name:   Linux-4.14.180-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4600384 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
   Booting using the fdt blob at 0x61000000
   Loading Kernel Image ... OK
   Loading Device Tree to 67e26000, end 67e2b2bb ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug V3 Classic
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=LABEL=rootfs mtdparts=41000000.nand:14m(boot),-(ubi) earlyprintk=serial
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119032K/131072K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 12040K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0800000   (8160 kB)
[    0.000000]       .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
[    0.000000]       .data : 0xc0b00000 - 0xc0b31f68   ( 200 kB)
[    0.000000]        .bss : 0xc0b383b8 - 0xc0b757c0   ( 246 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008171] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.018897] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.025057] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.033592] GIC: PPI13 is secure or misconfigured
[    0.038397] GIC: PPI13 is secure or misconfigured
[    0.043325] Console: colour dummy device 80x30
[    0.047836] console [tty0] enabled
[    0.051374] bootconsole [earlycon0] disabled
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug V3 Classic
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=LABEL=rootfs mtdparts=41000000.nand:14m(boot),-(ubi) earlyprintk=serial
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119032K/131072K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 12040K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0800000   (8160 kB)
[    0.000000]       .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
[    0.000000]       .data : 0xc0b00000 - 0xc0b31f68   ( 200 kB)
[    0.000000]        .bss : 0xc0b383b8 - 0xc0b757c0   ( 246 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008171] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.018897] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.025057] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.033592] GIC: PPI13 is secure or misconfigured
[    0.038397] GIC: PPI13 is secure or misconfigured
[    0.043325] Console: colour dummy device 80x30
[    0.047836] console [tty0] enabled
[    0.051374] bootconsole [earlycon0] disabled
[    0.055749] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.098524] pid_max: default: 32768 minimum: 301
[    0.098810] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098856] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.099811] CPU: Testing write buffer coherency: ok
[    0.138562] Setting up static identity map for 0x60100000 - 0x60100038
[    0.158456] Hierarchical SRCU implementation.
[    0.198458] smp: Bringing up secondary CPUs ...
[    0.268577] GIC: PPI13 is secure or misconfigured
[    0.328773] smp: Brought up 1 node, 2 CPUs
[    0.328834] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[    0.329623] devtmpfs: initialized
[    0.335444] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.335511] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.335882] prandom: seed boundary self test passed
[    0.340456] prandom: 100 self tests passed
[    0.340492] pinctrl core: initialized pinctrl subsystem
[    0.341232] NET: Registered protocol family 16
[    0.342947] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.345525] cpuidle: using governor ladder
[    0.345615] cpuidle: using governor menu
[    0.364282] vgaarb: loaded
[    0.364856] SCSI subsystem initialized
[    0.365616] usbcore: registered new interface driver usbfs
[    0.365747] usbcore: registered new interface driver hub
[    0.365936] usbcore: registered new device driver usb
[    0.366159] pps_core: LinuxPPS API ver. 1 registered
[    0.366205] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.366272] PTP clock support registered
[    0.367352] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.384079] NET: Registered protocol family 2
[    0.385070] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.385149] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.385210] TCP: Hash tables configured (established 1024 bind 1024)
[    0.385408] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.385495] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.385797] NET: Registered protocol family 1
[    0.386618] RPC: Registered named UNIX socket transport module.
[    0.386675] RPC: Registered udp transport module.
[    0.386705] RPC: Registered tcp transport module.
[    0.386736] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.388421] Initialise system trusted keyrings
[    0.388526] Key type blacklist registered
[    0.388897] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.396052] zbud: loaded
[    0.400855] NFS: Registering the id_resolver key type
[    0.400936] Key type id_resolver registered
[    0.400967] Key type id_legacy registered
[    0.401011] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.401047] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.401971] fuse init (API version 7.26)
[    0.402941] orangefs_debugfs_init: called with debug mask: :none: :0:
[    0.403264] orangefs_init: module version upstream loaded
[    2.473630] Key type asymmetric registered
[    2.473694] Asymmetric key parser 'x509' registered
[    2.473825] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    2.473873] io scheduler noop registered
[    2.473902] io scheduler deadline registered
[    2.473986] io scheduler cfq registered (default)
[    2.475816] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    2.477539] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    3.051683] console [ttyS0] enabled
[    3.066513] loop: module loaded
[    3.071633] scsi host0: sata_oxnas
[    3.075381] ata1: SATA max UDMA/133 irq 57
[    3.079659] sata_oxnas: resetting SATA core
[    3.147712] nand: Could not find valid ONFI parameter page; aborting
[    3.154078] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    3.160476] nand: Hynix NAND 256MiB 3,3V 8-bit
[    3.164925] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.172538] Scanning device for bad blocks
[    3.203320] Bad eraseblock 324 at 0x000002880000
[    3.208012] Bad eraseblock 325 at 0x0000028a0000
[    3.355980] 2 ofpart partitions found on MTD device 41000000.nand-controller
[    3.363059] Creating 2 MTD partitions on "41000000.nand-controller":
[    3.369441] 0x000000000000-0x000000e00000 : "boot"
[    3.375930] 0x000000e00000-0x000008000000 : "data"
[    3.383992] libphy: Fixed MDIO Bus: probed
[    3.388648] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    3.394503] oxnas-dwmac 40400000.ethernet: no reset control found
[    3.467461] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    3.472532] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    3.478243] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    3.485550] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    3.492362] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    3.499005] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    3.506304] oxnas-dwmac 40400000.ethernet: COE Type 2
[    3.511383] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    3.518282] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    3.524546] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    3.541895] libphy: stmmac: probed
[    3.545326] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    3.554851] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    3.565314] PPP generic driver version 2.4.2
[    3.570001] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.576535] ehci-pci: EHCI PCI platform driver
[    3.597434] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    3.651409] ata1.00: HPA detected: current 156299375, native 156301488
[    3.658007] ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
[    3.663580] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    3.709729] ata1.00: configured for UDMA/133
[    3.724666] scsi 0:0:0:0: Direct-Access     ATA      ST380815AS       C    PQ: 0 ANSI: 5
[    3.734809] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    3.742732] sd 0:0:0:0: [sda] Write Protect is off
[    3.747832] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.783413]  sda: sda1 sda2 sda3
[    3.787473] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    3.793021] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    3.802864] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.807759] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    3.837411] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    3.843752] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.850647] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.857909] usb usb1: Product: EHCI Host Controller
[    3.862786] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd
[    3.869419] usb usb1: SerialNumber: 40200100.ehci
[    3.875072] hub 1-0:1.0: USB hub found
[    3.878970] hub 1-0:1.0: 2 ports detected
[    3.884049] usbcore: registered new interface driver cdc_wdm
[    3.889948] usbcore: registered new interface driver usb-storage
[    3.896125] usbcore: registered new interface driver usbserial
[    3.902072] usbcore: registered new interface driver usbserial_generic
[    3.908702] usbserial: USB Serial support registered for generic
[    3.915095] mousedev: PS/2 mouse device common for all mice
[    3.920860] i2c /dev entries driver
[    3.925639] hidraw: raw HID events driver (C) Jiri Kosina
[    3.931374] usbcore: registered new interface driver usbhid
[    3.936952] usbhid: USB HID core driver
[    3.942384] NET: Registered protocol family 10
[    3.948467] Segment Routing with IPv6
[    3.952238] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.960079] NET: Registered protocol family 17
[    3.964656] Key type dns_resolver registered
[    3.970329] registered taskstats version 1
[    3.974440] Loading compiled-in X.509 certificates
[    3.979404] zswap: loaded using pool lzo/zbud
[    3.992066] Key type big_key registered
[    3.998766] Key type encrypted registered
[    4.005058] hctosys: unable to open rtc device (rtc0)
[    4.011056] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6
[    4.019159] Please append a correct "root=" boot option; here are the available partitions:
[    4.027586] 1f00           14336 mtdblock0
[    4.027596]  (driver?)
[    4.034132] 1f01          116736 mtdblock1
[    4.034140]  (driver?)
[    4.040760] 0800        78149687 sda
[    4.040768]  driver: sd
[    4.046863]   0801           16384 sda1 00008000-01
[    4.046868]
[    4.053276]   0802         4194304 sda2 00008000-02
[    4.053281]
[    4.059706]   0803        73937975 sda3 00008000-03
[    4.059714]
[    4.066068] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    4.074324] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.14.180-oxnas-tld-1 #1
[    4.081438] Hardware name: Generic DT based system
[    4.086246] [<c01095b0>] (unwind_backtrace) from [<c01053bc>] (show_stack+0x10/0x14)
[    4.093998] [<c01053bc>] (show_stack) from [<c07384cc>] (dump_stack+0xb4/0xd0)
[    4.101222] [<c07384cc>] (dump_stack) from [<c0111b88>] (panic+0xec/0x268)
[    4.108103] [<c0111b88>] (panic) from [<c0a012bc>] (mount_block_root+0x1e0/0x2a8)
[    4.115589] [<c0a012bc>] (mount_block_root) from [<c0a0146c>] (mount_root+0xe8/0x128)
[    4.123412] [<c0a0146c>] (mount_root) from [<c0a015dc>] (prepare_namespace+0x130/0x194)
[    4.131409] [<c0a015dc>] (prepare_namespace) from [<c0a00e5c>] (kernel_init_freeable+0x17c/0x1c4)
[    4.140275] [<c0a00e5c>] (kernel_init_freeable) from [<c074b198>] (kernel_init+0x8/0x110)
[    4.148446] [<c074b198>] (kernel_init) from [<c01029b8>] (ret_from_fork+0x14/0x3c)
[    4.156014] CPU0: stopping
[    4.158743] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.14.180-oxnas-tld-1 #1
[    4.165862] Hardware name: Generic DT based system
[    4.170664] [<c01095b0>] (unwind_backtrace) from [<c01053bc>] (show_stack+0x10/0x14)
[    4.178411] [<c01053bc>] (show_stack) from [<c07384cc>] (dump_stack+0xb4/0xd0)
[    4.185635] [<c07384cc>] (dump_stack) from [<c01082a8>] (handle_IPI+0x190/0x1dc)
[    4.193034] [<c01082a8>] (handle_IPI) from [<c01014c8>] (gic_handle_irq+0x7c/0x8c)
[    4.200601] [<c01014c8>] (gic_handle_irq) from [<c0106278>] (__irq_svc+0x58/0x8c)
[    4.208069] Exception stack(0xc0b01f28 to 0xc0b01f70)
[    4.213114] 1f20:                   00000001 00000000 00000000 00000000 00000000 ffffe000
[    4.221281] 1f40: c0b03ae4 c0b03a88 00000000 00000000 c0a39e68 c08f607c 00000000 c0b01f78
[    4.229442] 1f60: c0103278 c010327c 60000013 ffffffff
[    4.234493] [<c0106278>] (__irq_svc) from [<c010327c>] (arch_cpu_idle+0x28/0x30)
[    4.241891] [<c010327c>] (arch_cpu_idle) from [<c0149f5c>] (do_idle+0x180/0x1d4)
[    4.249287] [<c0149f5c>] (do_idle) from [<c014a270>] (cpu_startup_entry+0x18/0x1c)
[    4.256857] [<c014a270>] (cpu_startup_entry) from [<c0a00c50>] (start_kernel+0x368/0x3f8)
[    4.265031] [<c0a00c50>] (start_kernel) from [<60008074>] (0x60008074)
[    4.271559] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
OX820 # printenv
SET_dtb=fdt addr ${fdtaddr} ; fdt header
autoload=no
baudrate=115200
bootargs=root=LABEL=rootfs root=/dev/sda2
bootcmd=run ideboot
bootdelay=3
bootnew=bootm 60000000 - 61000000
bootold=bootm 60000000
console=console=ttyS0,115200n8
ethact=mii0
ethaddr=74:F0:6D:6A:1D:17
ext2_dtb=ext2load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb
ext2_ideboot=run ext2_uimage ; run ext2_dtb ; run SET_dtb ; run bootnew
ext2_uimage=ext2load ide 0:2 60000000 /boot/uImage
ext4_dtb=ext4load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb
ext4_ideboot=run ext4_uimage ; run ext4_dtb ; run SET_dtb ; run bootnew
ext4_uimage=ext4load ide 0:2 60000000 /boot/uImage
fdtaddr=61000000
filesize=1b79
ideboot=run ext4_ideboot
idebootold=${loadold} ;${bootold}
imgaddr=60000000
ipaddr=10.0.0.71
keypressed=1
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
netcon=echo switch to net console;setenv stderr nc;setenv stdin nc;setenv stdout nc;echo switch to net console
preboot=run safeboot
serialcon=echo switch to serial console;setenv stderr serial;setenv stdin serial;setenv stdout serial;echo switch to serial console
stderr=serial
stdin=serial
stdout=serial
updboot=bootp;tftp 60000000 u-boot.img;ide write 60000000 400 400

Environment size: 1311/16380 bytes
OX820 #

setenv bootargs 'root=LABEL=rootfs mtdparts=41000000.nand:14m(boot),-(ubi) earlyprintk=serial'

OX820 # setenv bootargs root=LABEL=rootfs root=/dev/sda2
OX820 # printenv bootargs
bootargs=root=LABEL=rootfs root=/dev/sda2
OX820 # saveenv
Saving Environment to FAT...
writing u-boot.env
done
OX820 #

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
4600448 bytes read in 723 ms (6.1 MiB/s)
8892 bytes read in 41 ms (210.9 KiB/s)
magic:                  0xd00dfeed
totalsize:              0x22bc (8892)
off_dt_struct:          0x38
off_dt_strings:         0x1f98
off_mem_rsvmap:         0x28
version:                17
last_comp_version:      16
boot_cpuid_phys:        0x0
size_dt_strings:        0x324
size_dt_struct:         0x1f60
number mem_rsv:         0x0

## Booting kernel from Legacy Image at 60000000 ...
   Image Name:   Linux-4.14.180-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4600384 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
   Booting using the fdt blob at 0x61000000
   Loading Kernel Image ... OK
   Loading Device Tree to 67e26000, end 67e2b2bb ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug V3 Classic
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=LABEL=rootfs root=/dev/sda2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119032K/131072K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 12040K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0800000   (8160 kB)
[    0.000000]       .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
[    0.000000]       .data : 0xc0b00000 - 0xc0b31f68   ( 200 kB)
[    0.000000]        .bss : 0xc0b383b8 - 0xc0b757c0   ( 246 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000051] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000066] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000092] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000250] GIC: PPI13 is secure or misconfigured
[    0.000307] GIC: PPI13 is secure or misconfigured
[    0.000486] Console: colour dummy device 80x30
[    0.001269] console [tty0] enabled
[    0.001323] Calibrating delay loop... 317.03 BogoMIPS (lpj=1585152)
[    0.060275] pid_max: default: 32768 minimum: 301
[    0.060605] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060661] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.061626] CPU: Testing write buffer coherency: ok
[    0.100467] Setting up static identity map for 0x60100000 - 0x60100038
[    0.120363] Hierarchical SRCU implementation.
[    0.160366] smp: Bringing up secondary CPUs ...
[    0.230484] GIC: PPI13 is secure or misconfigured
[    0.290677] smp: Brought up 1 node, 2 CPUs
[    0.290757] SMP: Total of 2 processors activated (636.51 BogoMIPS).
[    0.291558] devtmpfs: initialized
[    0.297287] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.297369] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.297740] prandom: seed boundary self test passed
[    0.302330] prandom: 100 self tests passed
[    0.302371] pinctrl core: initialized pinctrl subsystem
[    0.303137] NET: Registered protocol family 16
[    0.304837] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.307640] cpuidle: using governor ladder
[    0.307750] cpuidle: using governor menu
[    0.327260] vgaarb: loaded
[    0.327841] SCSI subsystem initialized
[    0.328622] usbcore: registered new interface driver usbfs
[    0.328775] usbcore: registered new interface driver hub
[    0.328967] usbcore: registered new device driver usb
[    0.329198] pps_core: LinuxPPS API ver. 1 registered
[    0.329239] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.329308] PTP clock support registered
[    0.330437] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.347292] NET: Registered protocol family 2
[    0.348275] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.348357] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.348421] TCP: Hash tables configured (established 1024 bind 1024)
[    0.348620] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.348700] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.349007] NET: Registered protocol family 1
[    0.349772] RPC: Registered named UNIX socket transport module.
[    0.349829] RPC: Registered udp transport module.
[    0.349859] RPC: Registered tcp transport module.
[    0.349888] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.351646] Initialise system trusted keyrings
[    0.351756] Key type blacklist registered
[    0.352071] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.359047] zbud: loaded
[    0.363962] NFS: Registering the id_resolver key type
[    0.364044] Key type id_resolver registered
[    0.364075] Key type id_legacy registered
[    0.364124] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.364160] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.365096] fuse init (API version 7.26)
[    0.366072] orangefs_debugfs_init: called with debug mask: :none: :0:
[    0.366402] orangefs_init: module version upstream loaded
[    2.447646] Key type asymmetric registered
[    2.447708] Asymmetric key parser 'x509' registered
[    2.447838] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    2.447889] io scheduler noop registered
[    2.447918] io scheduler deadline registered
[    2.447994] io scheduler cfq registered (default)
[    2.449763] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    2.451502] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    3.013409] console [ttyS0] enabled
[    3.028183] loop: module loaded
[    3.033384] scsi host0: sata_oxnas
[    3.037150] ata1: SATA max UDMA/133 irq 57
[    3.041423] sata_oxnas: resetting SATA core
[    3.110786] nand: Could not find valid ONFI parameter page; aborting
[    3.117158] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    3.123558] nand: Hynix NAND 256MiB 3,3V 8-bit
[    3.128005] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.135621] Scanning device for bad blocks
[    3.166405] Bad eraseblock 324 at 0x000002880000
[    3.171100] Bad eraseblock 325 at 0x0000028a0000
[    3.317227] 2 ofpart partitions found on MTD device 41000000.nand-controller
[    3.324298] Creating 2 MTD partitions on "41000000.nand-controller":
[    3.330693] 0x000000000000-0x000000e00000 : "boot"
[    3.337162] 0x000000e00000-0x000008000000 : "data"
[    3.345205] libphy: Fixed MDIO Bus: probed
[    3.349795] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    3.355704] oxnas-dwmac 40400000.ethernet: no reset control found
[    3.430533] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    3.435601] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    3.441313] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    3.448619] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    3.455429] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    3.462069] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    3.469373] oxnas-dwmac 40400000.ethernet: COE Type 2
[    3.474449] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    3.481349] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    3.487610] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    3.504939] libphy: stmmac: probed
[    3.508369] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    3.517898] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    3.528424] PPP generic driver version 2.4.2
[    3.533089] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.539622] ehci-pci: EHCI PCI platform driver
[    3.560506] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    3.614315] ata1.00: HPA detected: current 156299375, native 156301488
[    3.620910] ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
[    3.626483] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    3.672637] ata1.00: configured for UDMA/133
[    3.677501] scsi 0:0:0:0: Direct-Access     ATA      ST380815AS       C    PQ: 0 ANSI: 5
[    3.687221] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    3.695659] sd 0:0:0:0: [sda] Write Protect is off
[    3.700812] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.729607]  sda: sda1 sda2 sda3
[    3.735603] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.750504] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    3.756042] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    3.763960] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    3.790489] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    3.796830] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.803676] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.810936] usb usb1: Product: EHCI Host Controller
[    3.815813] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd
[    3.822453] usb usb1: SerialNumber: 40200100.ehci
[    3.828008] hub 1-0:1.0: USB hub found
[    3.831943] hub 1-0:1.0: 2 ports detected
[    3.837002] usbcore: registered new interface driver cdc_wdm
[    3.842882] usbcore: registered new interface driver usb-storage
[    3.849067] usbcore: registered new interface driver usbserial
[    3.855045] usbcore: registered new interface driver usbserial_generic
[    3.861675] usbserial: USB Serial support registered for generic
[    3.868078] mousedev: PS/2 mouse device common for all mice
[    3.873873] i2c /dev entries driver
[    3.878643] hidraw: raw HID events driver (C) Jiri Kosina
[    3.884313] usbcore: registered new interface driver usbhid
[    3.889889] usbhid: USB HID core driver
[    3.895127] NET: Registered protocol family 10
[    3.901306] Segment Routing with IPv6
[    3.905077] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.912819] NET: Registered protocol family 17
[    3.917401] Key type dns_resolver registered
[    3.922880] registered taskstats version 1
[    3.926996] Loading compiled-in X.509 certificates
[    3.931996] zswap: loaded using pool lzo/zbud
[    3.944629] Key type big_key registered
[    3.951280] Key type encrypted registered
[    3.957281] hctosys: unable to open rtc device (rtc0)
[    3.989736] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[    3.997578] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[    4.020981] devtmpfs: mounted
[    4.025748] Freeing unused kernel memory: 1024K
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
ERROR: could not open /proc/stat: No such file or directory
findfs: unable to resolve 'LABEL=rootfs'
[    5.530170] random: fast init done
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
[    6.200893] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    6.221073] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    6.229365] random: systemd-udevd: uninitialized urandom read (16 bytes read)
.
[ ok ] Synthesizing the initial hotplug events...done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[    8.860249] EXT4-fs (sda2): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.29.2
rootfs: clean, 18655/262144 files, 223055/1048576 blocks
done.
[    9.226708] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[....] Checking file systems...fsck from util-linux 2.29.2
done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Loading kernel modules...done.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

[   13.232424] oxnas-dwmac 40400000.ethernet eth0: No phy led trigger registered for speed(-1)
[   13.240870] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[   13.255406] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   13.264284] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[   13.271383] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Listening on LPF/eth0/74:f0:6d:6a:1d:17
Sending on   LPF/eth0/74:f0:6d:6a:1d:17
Sending on   Socket/fallback
DHCPREQUEST of 192.168.3.193 on eth0 to 255.255.255.255 port 67
[   14.311436] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   14.319920] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST of 192.168.3.193 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.3.193 from 192.168.3.1
[   21.160099] random: crng init done
[   21.163560] random: 7 urandom warning(s) missed due to ratelimiting
bound to 192.168.3.193 -- renewal in 21049 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1151 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1178 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.

Debian GNU/Linux 10 debian ttyS0

debian login: root
Password:
Last login: Wed Dec 31 16:00:34 PST 1969 on ttyS0
Linux debian 4.14.180-oxnas-tld-1 #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020 armv6l

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~#

+		bootargs = "earlyprintk";

+		bootargs = "earlyprintk root=/dev/sda2 rootfstype=ext4";

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
4620168 bytes read in 716 ms (6.2 MiB/s)
8924 bytes read in 39 ms (222.7 KiB/s)
magic:                  0xd00dfeed
totalsize:              0x22dc (8924)
off_dt_struct:          0x38
off_dt_strings:         0x1fb8
off_mem_rsvmap:         0x28
version:                17
last_comp_version:      16
boot_cpuid_phys:        0x0
size_dt_strings:        0x324
size_dt_struct:         0x1f80
number mem_rsv:         0x0

## Booting kernel from Legacy Image at 60000000 ...
   Image Name:   Linux-4.14.180-oxnas-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4620104 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
   Booting using the fdt blob at 0x61000000
   Loading Kernel Image ... OK
   Loading Device Tree to 67e26000, end 67e2b2db ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.180-oxnas-oxnas-tld-1 (admin@runtu) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Mon May 25 19:37:15 MSK 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug V3 Classic
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk root=/dev/sda2 rootfstype=ext4
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119032K/131072K available (7168K kernel code, 199K rwdata, 1520K rodata, 1024K init, 246K bss, 12040K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0800000   (8160 kB)
[    0.000000]       .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
[    0.000000]       .data : 0xc0b00000 - 0xc0b31f40   ( 200 kB)
[    0.000000]        .bss : 0xc0b38318 - 0xc0b75c38   ( 247 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008166] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.018897] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.025054] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.033587] GIC: PPI13 is secure or misconfigured
[    0.038394] GIC: PPI13 is secure or misconfigured
[    0.043328] Console: colour dummy device 80x30
[    0.047841] console [tty0] enabled
[    0.051379] bootconsole [earlycon0] disabled
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.180-oxnas-oxnas-tld-1 (admin@runtu) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Mon May 25 19:37:15 MSK 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug V3 Classic
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk root=/dev/sda2 rootfstype=ext4
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119032K/131072K available (7168K kernel code, 199K rwdata, 1520K rodata, 1024K init, 246K bss, 12040K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0800000   (8160 kB)
[    0.000000]       .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
[    0.000000]       .data : 0xc0b00000 - 0xc0b31f40   ( 200 kB)
[    0.000000]        .bss : 0xc0b38318 - 0xc0b75c38   ( 247 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008166] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.018897] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.025054] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.033587] GIC: PPI13 is secure or misconfigured
[    0.038394] GIC: PPI13 is secure or misconfigured
[    0.043328] Console: colour dummy device 80x30
[    0.047841] console [tty0] enabled
[    0.051379] bootconsole [earlycon0] disabled
[    0.055756] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.098513] pid_max: default: 32768 minimum: 301
[    0.098810] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098856] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.099850] CPU: Testing write buffer coherency: ok
[    0.138557] Setting up static identity map for 0x60100000 - 0x60100038
[    0.158453] Hierarchical SRCU implementation.
[    0.198456] smp: Bringing up secondary CPUs ...
[    0.268569] GIC: PPI13 is secure or misconfigured
[    0.328768] smp: Brought up 1 node, 2 CPUs
[    0.328834] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[    0.329635] devtmpfs: initialized
[    0.335592] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.335654] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.336033] prandom: seed boundary self test passed
[    0.340510] prandom: 100 self tests passed
[    0.340541] pinctrl core: initialized pinctrl subsystem
[    0.341324] NET: Registered protocol family 16
[    0.343006] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.346293] cpuidle: using governor ladder
[    0.346385] cpuidle: using governor menu
[    0.366973] vgaarb: loaded
[    0.367567] SCSI subsystem initialized
[    0.368337] usbcore: registered new interface driver usbfs
[    0.368583] usbcore: registered new interface driver hub
[    0.368785] usbcore: registered new device driver usb
[    0.369003] pps_core: LinuxPPS API ver. 1 registered
[    0.369049] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.369118] PTP clock support registered
[    0.370352] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.388825] NET: Registered protocol family 2
[    0.389849] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.389931] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.389992] TCP: Hash tables configured (established 1024 bind 1024)
[    0.390200] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.390279] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.390722] NET: Registered protocol family 1
[    0.391498] RPC: Registered named UNIX socket transport module.
[    0.391552] RPC: Registered udp transport module.
[    0.391582] RPC: Registered tcp transport module.
[    0.391613] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.393392] Initialise system trusted keyrings
[    0.393492] Key type blacklist registered
[    0.393812] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.403543] zbud: loaded
[    0.409088] NFS: Registering the id_resolver key type
[    0.409167] Key type id_resolver registered
[    0.409200] Key type id_legacy registered
[    0.409249] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.409285] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.410460] fuse init (API version 7.26)
[    0.411640] orangefs_debugfs_init: called with debug mask: :none: :0:
[    0.412021] orangefs_init: module version upstream loaded
[    2.556979] Key type asymmetric registered
[    2.557045] Asymmetric key parser 'x509' registered
[    2.557171] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    2.557224] io scheduler noop registered
[    2.557255] io scheduler deadline registered
[    2.557345] io scheduler cfq registered (default)
[    2.559193] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    2.561018] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    3.135308] console [ttyS0] enabled
[    3.151370] loop: module loaded
[    3.156672] scsi host0: sata_oxnas
[    3.160558] ata1: SATA max UDMA/133 irq 57
[    3.164787] sata_oxnas: resetting SATA core
[    3.230725] nand: Could not find valid ONFI parameter page; aborting
[    3.237089] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    3.243489] nand: Hynix NAND 256MiB 3,3V 8-bit
[    3.247936] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.255549] Scanning device for bad blocks
[    3.286530] Bad eraseblock 324 at 0x000002880000
[    3.291230] Bad eraseblock 325 at 0x0000028a0000
[    3.437603] 2 ofpart partitions found on MTD device 41000000.nand-controller
[    3.444679] Creating 2 MTD partitions on "41000000.nand-controller":
[    3.451074] 0x000000000000-0x000000e00000 : "boot"
[    3.457738] 0x000000e00000-0x000008000000 : "data"
[    3.466014] libphy: Fixed MDIO Bus: probed
[    3.470686] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    3.476538] oxnas-dwmac 40400000.ethernet: no reset control found
[    3.550458] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    3.555527] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    3.561244] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    3.568550] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    3.575367] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    3.582016] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    3.589324] oxnas-dwmac 40400000.ethernet: COE Type 2
[    3.594408] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    3.601313] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    3.607580] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    3.635100] libphy: stmmac: probed
[    3.638533] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    3.648064] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    3.658657] PPP generic driver version 2.4.2
[    3.663339] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.669872] ehci-pci: EHCI PCI platform driver
[    3.690416] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    3.742579] ata1.00: HPA detected: current 156299375, native 156301488
[    3.749125] ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
[    3.754757] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    3.800901] ata1.00: configured for UDMA/133
[    3.805793] scsi 0:0:0:0: Direct-Access     ATA      ST380815AS       C    PQ: 0 ANSI: 5
[    3.815851] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    3.823705] sd 0:0:0:0: [sda] Write Protect is off
[    3.828733] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.857845]  sda: sda1 sda2 sda3
[    3.864273] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.880453] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    3.886018] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    3.893959] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    3.920424] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    3.926771] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.933624] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.940881] usb usb1: Product: EHCI Host Controller
[    3.945756] usb usb1: Manufacturer: Linux 4.14.180-oxnas-oxnas-tld-1 ehci_hcd
[    3.952916] usb usb1: SerialNumber: 40200100.ehci
[    3.958609] hub 1-0:1.0: USB hub found
[    3.962562] hub 1-0:1.0: 2 ports detected
[    3.967697] usbcore: registered new interface driver cdc_wdm
[    3.973608] usbcore: registered new interface driver usb-storage
[    3.979776] usbcore: registered new interface driver usbserial
[    3.985758] usbcore: registered new interface driver usbserial_generic
[    3.992396] usbserial: USB Serial support registered for generic
[    3.998794] mousedev: PS/2 mouse device common for all mice
[    4.004597] i2c /dev entries driver
[    4.009487] hidraw: raw HID events driver (C) Jiri Kosina
[    4.015173] usbcore: registered new interface driver usbhid
[    4.020807] usbhid: USB HID core driver
[    4.026196] NET: Registered protocol family 10
[    4.032407] Segment Routing with IPv6
[    4.036175] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.044170] NET: Registered protocol family 17
[    4.048770] Key type dns_resolver registered
[    4.054371] registered taskstats version 1
[    4.058483] Loading compiled-in X.509 certificates
[    4.063444] zswap: loaded using pool lzo/zbud
[    4.076848] Key type big_key registered
[    4.083540] Key type encrypted registered
[    4.089786] hctosys: unable to open rtc device (rtc0)
[    4.118031] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[    4.125977] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[    4.149084] devtmpfs: mounted
[    4.153953] Freeing unused kernel memory: 1024K
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
ERROR: could not open /proc/stat: No such file or directory
findfs: unable to resolve 'LABEL=rootfs'
[    5.635230] random: fast init done
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
[    6.323276] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    6.340664] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    6.348229] random: systemd-udevd: uninitialized urandom read (16 bytes read)
.
[ ok ] Synthesizing the initial hotplug events...done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[    9.013598] EXT4-fs (sda2): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.29.2
rootfs: clean, 17094/262144 files, 205491/1048576 blocks
done.
[    9.388270] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[....] Checking file systems...fsck from util-linux 2.29.2
done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Loading kernel modules...done.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

[   13.377625] oxnas-dwmac 40400000.ethernet eth0: No phy led trigger registered for speed(-1)
[   13.386135] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[   13.400558] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   13.412894] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[   13.420019] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Listening on LPF/eth0/74:f0:6d:6a:1d:17
Sending on   LPF/eth0/74:f0:6d:6a:1d:17
Sending on   Socket/fallback
DHCPREQUEST of 192.168.3.193 on eth0 to 255.255.255.255 port 67
[   14.441441] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   14.449925] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST of 192.168.3.193 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.3.193 from 192.168.3.1
[   20.031741] random: crng init done
[   20.035171] random: 7 urandom warning(s) missed due to ratelimiting
bound to 192.168.3.193 -- renewal in 18773 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1150 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1177 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.

Debian GNU/Linux 10 debian ttyS0

debian login: root
Password:
Last login: Wed Dec 31 16:00:35 PST 1969 on ttyS0
Linux debian 4.14.180-oxnas-oxnas-tld-1 #1 SMP PREEMPT Mon May 25 19:37:15 MSK 2020 armv6l

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~#