Pogoplug V4 no longer boots

Re: Pogoplug V4 no longer boots

bodhi — Mon, 30 Dec 2019 01:57:47 -0600

Cool! Glad to hear.

Re: Pogoplug V4 no longer boots

Olek — Sun, 29 Dec 2019 13:07:09 -0600

Bodhi,

A quick heads-up before you spend any more time on this - I went ahead and restored uboot's 's envs from the default ones per instructions in the Uboot section and voila, the system booted up.

The working envs:

bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide mmc
disks=0 1 2 3
ethact=egiga0
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb_addr=0x1c00000
load_initrd_addr=0x1100000
load_uimage_addr=0x800000
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
mainlineLinux=yes
mtdids=nand0=orion_nand
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
usb_ready_retry=15
arcNumber=3960
machid=f78
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
ethaddr=00:11:22:33:44:55
uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done
uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type  $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done;
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi; sleep 3
dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb

Thanks a bunch for your help!
Olek

Re: Pogoplug V4 no longer boots

bodhi — Sun, 29 Dec 2019 01:55:12 -0600

Olek,

I am in transit (on travel). Will check back to give you a hand.

Basically, your current envs are wrong since it can only boot USB rootfs.

Once you restore the envs to the default state. It can boot any type of drives.

Re: Pogoplug V4 no longer boots

Olek — Sat, 28 Dec 2019 21:48:24 -0600

Bodhi,

Managed to boot the system with pristine Debian (5.2.9) per this post, thank you very much:
https://forum.doozan.com/read.php?3,28772,29034#msg-29034

Sadly, the 5.4.2 installation no longer exist - I wiped it out.
Now I need to figure out how to clean up the envs.

Thanks!
O.

Re: Pogoplug V4 no longer boots

bodhi — Sat, 28 Dec 2019 18:09:45 -0600

Hold on,

Your envs actually are messed up badly.

Re: Pogoplug V4 no longer boots

bodhi — Sat, 28 Dec 2019 17:45:49 -0600

Olek,

When you said "unsuccessful upgrade to 5.4.2", I am sure your rootfs is messed up. Especially the /boot directory.

Mount the SD card on another Linux system, and assuming it was mounted at /media/sdb1,

cd /media/sdb1/boot
ls -lart

And post the output here.

Pogoplug V4 no longer boots

Olek — Sat, 28 Dec 2019 09:01:39 -0600

Hi there, first time poster on this forum.

I can no longer boot my pogoplug V4 (pink logo) to Debian after an unsuccessful upgrade to kernel 5.4.2.
Probably took the wrong turn somewhere in Step 4 (4b I guess).

Uboot messages:

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   MVEBU_MMC: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Reset IDE: ide_preinit failed

MMC rescan: current device # 0 initialized OK
## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** Bad device usb 0 **

no IDE devices available

Partition Map for MMC device 0  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	2048      	31289344  	fd637859-01	83 Boot
loading envs from mmc 0 ...
** File not found /boot/uEnv.txt **
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide

Reset IDE: ide_preinit failed
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
Scan device mmc

MMC rescan: current device # 0 initialized OK
device mmc 0:1
1 bytes read in 23 ms (0 Bytes/s)
Found bootable drive on mmc 0
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!

Contents of messed-up uboot printenv:

arcNumber=3960
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide mmc
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb
ethact=egiga0
ethaddr=00:11:22:33:44:55
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb
load_dtb_addr=0x1c00000
load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uimage_addr=0x800000
machid=f78
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi
usb_ready_retry=15

Environment size: 2921/131068 bytes

For comparison, this is the copy of the envs from the PREVIOUSLY working uboot:

arcNumber=3960
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide mmc
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb
ethact=egiga0
ethaddr=00:11:22:33:44:55
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
machid=f78
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_ready_retry=15

Environment size: 2863/131068 bytes

I attempted the kwboot, but still can't boot to Debian (I have a backup copy made prior to this attempt). Nor can I access the ext3-formatted USB stick with a copy of mtd0 partition.
Also, the envs are identical (kwboot and now-messed up uboot) if it matters.

What is the best way to recover from this mess?

The long term goal is to have the pogoplug serve as asterisk server and a light duty NAS if booting issue can be fixed.

Thanks in advance.
O.