Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1751 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1730 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.32.18-dockstar Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3175992 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux......................................................................................................................................................................................................... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.32.18-dockstar (root@stfu.tcbnet) (gcc version 4.3.5 (Buildroot 2010.08) ) #1 Thu Sep 16 16:04:06 EDT 2010 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Marvell SheevaPlug Reference Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 122964KB available (5852K code, 695K data, 124K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000000] Console: colour dummy device 80x30 [ 21.474959] Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776) [ 21.714914] Security Framework initialized [ 21.714933] SELinux: Disabled at boot. [ 21.714953] Mount-cache hash table entries: 512 [ 21.715202] Initializing cgroup subsys ns [ 21.715215] Initializing cgroup subsys cpuacct [ 21.715224] Initializing cgroup subsys devices [ 21.715233] Initializing cgroup subsys freezer [ 21.715241] Initializing cgroup subsys net_cls [ 21.715275] CPU: Testing write buffer coherency: ok [ 21.715827] devtmpfs: initialized [ 21.717252] regulator: core version 0.5 [ 21.717353] NET: Registered protocol family 16 [ 21.717735] Kirkwood: MV88F6281-A0, TCLK=200000000. [ 21.717747] Feroceon L2: Cache support initialised. [ 21.720711] bio: create slab at 0 [ 21.721004] vgaarb: loaded [ 21.721269] SCSI subsystem initialized [ 21.721521] usbcore: registered new interface driver usbfs [ 21.721581] usbcore: registered new interface driver hub [ 21.721680] usbcore: registered new device driver usb [ 21.722119] Switching to clocksource orion_clocksource [ 21.727473] NET: Registered protocol family 2 [ 21.727723] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 21.728500] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 21.728599] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 21.728653] TCP: Hash tables configured (established 4096 bind 4096) [ 21.728663] TCP reno registered [ 21.728820] NET: Registered protocol family 1 [ 21.729084] RPC: Registered udp transport module. [ 21.729093] RPC: Registered tcp transport module. [ 21.729101] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 21.729255] NetWinder Floating Point Emulator V0.97 (double precision) [ 21.729501] audit: initializing netlink socket (disabled) [ 21.729533] type=2000 audit(0.242:1): initialized [ 21.736370] VFS: Disk quotas dquot_6.5.2 [ 21.736626] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 21.739233] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 21.740863] Registering the dns_resolver key type [ 21.740911] Slow work thread pool: Starting up [ 21.741034] Slow work thread pool: Ready [ 21.741043] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 21.741814] fuse init (API version 7.13) [ 21.742302] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 21.743868] msgmni has been set to 240 [ 21.745948] alg: No test for stdrng (krng) [ 21.746117] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 21.746130] io scheduler noop registered [ 21.746137] io scheduler anticipatory registered [ 21.746145] io scheduler deadline registered [ 21.746405] io scheduler cfq registered (default) [ 21.752380] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 21.752842] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 22.134850] console [ttyS0] enabled [ 22.138939] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) [ 22.147557] Scanning device for bad blocks [ 22.162659] Bad eraseblock 295 at 0x0000024e0000 [ 22.211838] Bad eraseblock 1497 at 0x00000bb20000 [ 22.236975] 4 cmdlinepart partitions found on MTD device orion_nand [ 22.243292] Creating 4 MTD partitions on "orion_nand": [ 22.248460] 0x000000000000-0x000000100000 : "u-boot" [ 22.254024] 0x000000100000-0x000000500000 : "uImage" [ 22.259458] 0x000000500000-0x000002500000 : "rootfs" [ 22.264938] 0x000002500000-0x000010000000 : "data" [ 22.270622] UBI: attaching mtd2 to ubi0 [ 22.274498] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 22.280795] UBI: logical eraseblock size: 129024 bytes [ 22.286228] UBI: smallest flash I/O unit: 2048 [ 22.290953] UBI: sub-page size: 512 [ 22.295601] UBI: VID header offset: 512 (aligned 512) [ 22.301461] UBI: data offset: 2048 [ 22.365673] UBI: attached mtd2 to ubi0 [ 22.369442] UBI: MTD device name: "rootfs" [ 22.374537] UBI: MTD device size: 32 MiB [ 22.379435] UBI: number of good PEBs: 255 [ 22.384084] UBI: number of bad PEBs: 1 [ 22.388547] UBI: max. allowed volumes: 128 [ 22.393195] UBI: wear-leveling threshold: 4096 [ 22.397921] UBI: number of internal volumes: 1 [ 22.402394] UBI: number of user volumes: 1 [ 22.406859] UBI: available PEBs: 0 [ 22.411323] UBI: total number of reserved PEBs: 255 [ 22.416233] UBI: number of PEBs reserved for bad PEB handling: 2 [ 22.422276] UBI: max/mean erase counter: 6/1 [ 22.426567] UBI: image sequence number: 0 [ 22.430604] UBI: background thread "ubi_bgt0d" started, PID 38 [ 22.436642] MV-643xx 10/100/1000 ethernet driver version 1.4 [ 22.442422] mv643xx_eth smi: probed [ 22.447711] net eth0: port 0 with MAC address 00:10:75:1a:94:b9 [ 22.453753] console [netcon0] enabled [ 22.457426] netconsole: network logging started [ 22.461979] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 22.468590] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 22.473902] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 22.502172] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 22.522156] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 22.528158] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 22.534990] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 22.542257] usb usb1: Product: Marvell Orion EHCI [ 22.546983] usb usb1: Manufacturer: Linux 2.6.32.18-dockstar ehci_hcd [ 22.553461] usb usb1: SerialNumber: orion-ehci.0 [ 22.558372] usb usb1: configuration #1 chosen from 1 choice [ 22.564103] hub 1-0:1.0: USB hub found [ 22.567893] hub 1-0:1.0: 1 port detected [ 22.572066] Initializing USB Mass Storage driver... [ 22.577069] usbcore: registered new interface driver usb-storage [ 22.583119] USB Mass Storage support registered. [ 22.587963] mice: PS/2 mouse device common for all mice [ 22.593284] i2c /dev entries driver [ 22.597580] device-mapper: uevent: version 1.0.3 [ 22.602637] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com [ 22.611199] cpuidle: using governor ladder [ 22.615466] cpuidle: using governor menu [ 22.619512] Registered led device: dockstar:green:health [ 22.624936] Registered led device: dockstar:orange:health [ 22.630417] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver [ 22.636832] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver [ 22.682191] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 22.722187] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) [ 22.762240] mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) [ 22.802185] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) [ 22.809068] TCP cubic registered [ 22.812338] NET: Registered protocol family 17 [ 22.817178] registered taskstats version 1 [ 22.821997] Initalizing network drop monitor service [ 22.827115] md: Waiting for all devices to be available before autodetect [ 22.833955] md: If you don't use raid, use raid=noautodetect [ 22.840034] md: Autodetecting RAID arrays. [ 22.844169] md: Scanned 0 and added 0 devices. [ 22.848632] md: autorun ... [ 22.851430] md: ... autorun DONE. [ 22.906020] usb 1-1: new high speed USB device using orion-ehci and address 2 [ 22.964520] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 22.970572] UBIFS: mounted read-only [ 22.974201] UBIFS: file system size: 30707712 bytes (29988 KiB, 29 MiB, 238 LEBs) [ 22.981893] UBIFS: journal size: 9033728 bytes (8822 KiB, 8 MiB, 71 LEBs) [ 22.989250] UBIFS: media format: w4/r0 (latest is w4/r0) [ 22.995121] UBIFS: default compressor: lzo [ 22.999235] UBIFS: reserved for root: 0 bytes (0 KiB) [ 23.005144] VFS: Mounted root (ubifs filesystem) readonly on device 0:16. [ 23.012008] Freeing init memory: 124K [ 23.094067] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 23.100810] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 23.108031] usb 1-1: Product: USB2.0 Hub [ 23.128247] usb 1-1: configuration #1 chosen from 1 choice [ 23.143107] hub 1-1:1.0: USB hub found [ 23.152244] hub 1-1:1.0: 4 ports detected Initializing random number generator... read-only file system detected...done Starting network... [ 23.432469] usb 1-1.2: new high speed USB device using orion-ehci and address 3 [ 24.863308] usb 1-1.2: New USB device found, idVendor=14cd, idProduct=6116 [ 24.870220] usb 1-1.2: New USB device strings: Mfr=1, Product=3, SerialNumber=2 [ 24.877573] usb 1-1.2: Product: USB 2.0 SATA BRIDGE [ 24.882859] usb 1-1.2: Manufacturer: Super Top [ 24.887587] usb 1-1.2: SerialNumber: M6116018VE15 [ 24.892934] usb 1-1.2: configuration #1 chosen from 1 choice [ 24.903231] scsi0 : SCSI emulation for USB Mass Storage devices [ 29.913021] scsi 0:0:0:0: Direct-Access ST925031 5AS PQ: 0 ANSI: 0 ntpd: bad address 'pool.ntp.org' run-parts: /etc/network/if-up.d/ntpd exited with code 1 Starting Network Interface Plugging Daemon: eth0. Starting sshd: OK Starting heartbeat LED... Jeff Doozan's Dockstar/Pogoplug Recovery System rescue login: [ 37.213433] eth0: link up, 100 Mb/s, full duplex, flow control disabled