__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** uboot_ver:v0.1.7 ** ** MARVELL BOARD: 88F6702A-TCC LE U-Boot 1.1.4 (Jun 25 2012 - 11:53:33) Marvell version: 3.6.0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0 Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz SysClock = 400Mhz , TClock = 166Mhz DRAM (DDR2) CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [512kB@f8000000] Flash: 512 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> run ide_boot Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: WDC WD800AAJS-00WAA0 Firm: 58.01D58 Ser#: WD-WCAS25057693 Type: Hard Disk Supports 48-bit addressing Capacity: 76318.0 MB = 74.5 GB (156299375 x 512) 3164436 bytes read 7179935 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2017-06-23 11:48:35 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3164372 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Canvio Home NAS [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=spi_flash:0x0007E000@0x0(uboot),0x00001000@0x0007E000(param),0x00001000@0x0007F000(param2),0x80000@0x0(flash) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 113632K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000010] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.008218] Console: colour dummy device 80x30 [ 0.012746] Calibrating delay loop... 990.41 BogoMIPS (lpj=4952064) [ 0.100730] pid_max: default: 32768 minimum: 301 [ 0.105514] Security Framework initialized [ 0.109785] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.116468] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.124460] Initializing cgroup subsys io [ 0.128612] Initializing cgroup subsys devices [ 0.133141] Initializing cgroup subsys freezer [ 0.137678] Initializing cgroup subsys net_cls [ 0.142309] CPU: Testing write buffer coherency: ok [ 0.147714] Setting up static identity map for 0x8200 - 0x8258 [ 0.153946] mvebu-soc-id: MVEBU SoC ID=0x6702, Rev=0x3 [ 0.163177] devtmpfs: initialized [ 0.171485] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.181884] prandom: seed boundary self test passed [ 0.191397] prandom: 100 self tests passed [ 0.195583] pinctrl core: initialized pinctrl subsystem [ 0.202388] NET: Registered protocol family 16 [ 0.207393] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.237974] cpuidle: using governor ladder [ 0.267974] cpuidle: using governor menu [ 0.272425] Feroceon L2: Enabling L2 [ 0.276103] Feroceon L2: Cache support initialised. [ 0.281493] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.297355] No ATAGs? [ 0.329605] vgaarb: loaded [ 0.333040] usbcore: registered new interface driver usbfs [ 0.338727] usbcore: registered new interface driver hub [ 0.344178] usbcore: registered new device driver usb [ 0.350545] clocksource: Switched to clocksource orion_clocksource [ 0.420867] NET: Registered protocol family 2 [ 0.426182] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.433350] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.439774] TCP: Hash tables configured (established 1024 bind 1024) [ 0.446275] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.452207] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.458742] NET: Registered protocol family 1 [ 0.463573] RPC: Registered named UNIX socket transport module. [ 0.469551] RPC: Registered udp transport module. [ 0.474372] RPC: Registered tcp transport module. [ 0.479142] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.485965] Unpacking initramfs... [ 1.228855] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 1.234941] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.242768] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.248990] audit: initializing netlink subsys (disabled) [ 1.254542] audit: type=2000 audit(1.240:1): initialized [ 1.260303] Initialise system trusted keyring [ 1.265165] zbud: loaded [ 1.268088] VFS: Disk quotas dquot_6.6.0 [ 1.272190] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.279797] NFS: Registering the id_resolver key type [ 1.285007] Key type id_resolver registered [ 1.289254] Key type id_legacy registered [ 1.293378] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.300138] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.306811] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.314514] Key type big_key registered [ 1.341087] Key type asymmetric registered [ 1.345268] Asymmetric key parser 'x509' registered [ 1.350304] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.357937] io scheduler noop registered [ 1.362006] io scheduler deadline registered [ 1.366400] io scheduler cfq registered (default) [ 1.372187] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 36 [ 1.379469] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 37 [ 1.386825] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 38 [ 1.394152] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 39 [ 1.401472] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 40 [ 1.408750] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 41 [ 1.416047] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 42 [ 1.423345] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 43 [ 1.430646] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 44 [ 1.437927] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 45 [ 1.445222] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 46 [ 1.452522] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47 [ 1.459795] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 48 [ 1.467090] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49 [ 1.474762] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 1.482904] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated [ 1.490288] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated [ 1.497840] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.541358] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.548960] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.591339] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.599235] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.607247] console [ttyS0] disabled [ 1.611012] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 10416666) is a 16550A [ 1.620049] console [ttyS0] enabled [ 1.620049] console [ttyS0] enabled [ 1.627124] bootconsole [earlycon0] disabled [ 1.627124] bootconsole [earlycon0] disabled [ 1.637995] m25p80 spi0.0: mx25l4005a (512 Kbytes) [ 1.649777] libphy: Fixed MDIO Bus: probed [ 1.654370] libphy: orion_mdio_bus: probed [ 1.663645] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 1.671852] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address e8:9d:87:f9:97:ff [ 1.680785] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.687310] ehci-pci: EHCI PCI platform driver [ 1.691866] ehci-orion: EHCI orion driver [ 1.696052] orion-ehci f1050000.ehci: EHCI Host Controller [ 1.701600] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 1.709393] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 1.730581] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 1.736811] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.743598] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.750811] usb usb1: Product: EHCI Host Controller [ 1.755672] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 1.762274] usb usb1: SerialNumber: f1050000.ehci [ 1.767780] hub 1-0:1.0: USB hub found [ 1.771604] hub 1-0:1.0: 1 port detected [ 1.776562] mousedev: PS/2 mouse device common for all mice [ 1.782887] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 1.789928] i2c /dev entries driver [ 1.794420] hidraw: raw HID events driver (C) Jiri Kosina [ 1.800223] drop_monitor: Initializing network drop monitor service [ 1.806807] NET: Registered protocol family 17 [ 1.811571] Key type dns_resolver registered [ 1.816788] registered taskstats version 1 [ 1.820954] Loading compiled-in X.509 certificates [ 1.825793] zswap: loaded using pool lzo/zbud [ 1.839292] Key type encrypted registered [ 1.843992] rtc-mv f1010300.rtc: setting system clock to 2000-03-19 02:51:13 UTC (953434273) [ 1.855012] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 1.937362] systemd-udevd[81]: starting version 215 [ 1.952929] random: systemd-udevd urandom read with 3 bits of entropy available [ 2.123637] SCSI subsystem initialized [ 2.182732] sata_mv f1080000.sata: slots 32 ports 1 [ 2.220772] scsi host0: sata_mv [ 2.224330] ata1: SATA max UDMA/133 irq 33 [ 2.730596] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 2.770620] ata1.00: HPA detected: current 156299375, native 156301488 [ 2.777128] ata1.00: ATA-8: WDC WD800AAJS-00WAA0, 58.01D58, max UDMA/133 [ 2.783823] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.830632] ata1.00: configured for UDMA/133 [ 2.851066] scsi 0:0:0:0: Direct-Access ATA WDC WD800AAJS-00 1D58 PQ: 0 ANSI: 5 [ 2.870205] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB) [ 2.881074] sd 0:0:0:0: [sda] Write Protect is off [ 2.885992] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.908896] sda: sda1 sda2 [ 2.914110] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.923016] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Checking root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 18.290965] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.329026] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 20.416793] systemd-udevd[288]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 20.877498] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 21.076796] marvell-cesa: probe of f1030000.crypto failed with error -524 [ 21.123520] orion_wdt: Initial timeout 25 sec done. [....] Activating swap...[ 22.663115] random: nonblocking pool is initialized done. [ 22.843898] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 14523/131072 files, 169840/524288 blocks done. [ 23.240766] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 26.347011] NET: Registered protocol family 10 [ 26.481570] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/e8:9d:87:f9:97:ff Sending on LPF/eth0/e8:9d:87:f9:97:ff Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 [ 30.216826] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 30.226666] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 192.168.1.1 bound to 192.168.1.50 -- renewal in 39047 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1230 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1233 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login: