__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** uboot_ver:v0.1.7 ** ** MARVELL BOARD: 88F6702A-TCC LE U-Boot 1.1.4 (Jun 25 2012 - 11:53:33) Marvell version: 3.6.0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0 Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz SysClock = 400Mhz , TClock = 166Mhz DRAM (DDR2) CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [512kB@f8000000] Flash: 512 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: TOSHIBA DT01ABA200 Firm: MZ4OABB0 Ser#: 34NN5Z3GS Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) 2696504 bytes read 2723840 bytes read ## Booting image at 02000000 ... Image Name: Linux-2.6.31.8canvio Created: 2013-08-20 6:33:08 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2696440 Bytes = 2.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux....................................................................................................................................................................... done, booting the kernel. Linux version 2.6.31.8canvio (jason@jasonNSR) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #2 Tue Aug 20 14:32:53 CST 2013 CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 CPU: VIVT data cache, VIVT instruction cache Machine: Feroceon-KW Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512 Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:0x0007E000@0x0(uboot),0x00001000@0x0007E000(param),0x00001000@0x0007F000(param2),0x80000@0x0(flash) root=/dev/ram0 rootfstype=cramfs init=/etc/rc.preroot initrd=0x800000,0x1000000 :::DB88FXX81:eth0:none PID hash table entries: 512 (order: 9, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 100848KB available (4888K code, 337K data, 140K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:128 Console: colour dummy device 80x30 Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352) Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok xor: measuring software checksum speed arm4regs : 903.200 MB/sec 8regs : 684.800 MB/sec 32regs : 699.600 MB/sec xor: using function: arm4regs (903.200 MB/sec) NET: Registered protocol family 16 Feroceon L2: Enabling L2 Feroceon L2: Cache support initialised. CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PEX1_MEM ....no such PEX1_IO ....no such INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- 88F6702A-TCC Soc: 88F6702 A1 LE Detected Tclk 166666667 and SysClk 400000000 MV Buttons Device Load Marvell USB EHCI Host controller #0: c403f740 PEX0 interface detected no Link. PCI: bus0: Fast back to back transfers enabled mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb raid6: int32x1 77 MB/s raid6: int32x2 95 MB/s raid6: int32x4 92 MB/s raid6: int32x8 92 MB/s raid6: using algorithm int32x2 (95 MB/s) NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (junk in compressed archive); looks like an initrd Freeing initrd memory: 16384K RTC has been updated!!! rtc mv_rtc: rtc core: registered kw-rtc as rtc0 RTC registered XOR registered 4 channels XOR 2nd invalidate WA enabled cesadev_init(c000ed58) mvCesaInit: sessions=640, queue=64, pSram=f0000000 MV Buttons Driver Load VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.12) SGI XFS with security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 229 alg: No test for cipher_null (cipher_null-generic) alg: No test for ecb(cipher_null) (ecb-cipher_null) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) alg: No test for stdrng (krng) alg: No test for hmac(digest_null) (hmac(digest_null-generic)) async_tx: api initialized (sync-only) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A console [ttyS0] enabled brd: module loaded loop: module loaded Integrated Sata device found IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter scsi 0:0:0:0: Direct-Access TOSHIBA DT01ABA200 MZ4O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512. sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 0:0:0:0: [sda] 0-byte physical blocks sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] Write Protect is off Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o 2 Giga ports supported o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue support - ETH_DEF_TXQ=0 o TCP segmentation offload (TSO) supported o Large Receive offload (LRO) supported o Receive checksum offload supported o Transmit checksum offload supported o Network Fast Processing (Routing) supported - (Disabled) o Proc tool API enabled o SKB Reuse supported - (Disabled) o SKB Recycle supported - (Disabled) o Rx descripors: q0=256 o Tx descripors: q0=532 o Loading network interface(s): o register under mv88fx_eth platform o egiga0, ifindex = 2, GbE port = 0 Warning: Giga 1 is Powered Off mvFpRuleDb (c1413000): 1024 entries, 4096 bytes sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512. SPI Serial flash detected @ 0xf4000000, 512KB (128sec x 4KB) 4 cmdlinepart partitions found on MTD device spi_flash Creating 4 MTD partitions on "spi_flash": 0x000000000000-0x00000007e000 : "uboot" 0x00000007e000-0x00000007f000 : "param" 0x00000007f000-0x000000080000 : "param2" sda: 0x000000000000-0x000000080000 : "flash" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 sda1 sda2 sda3 sda4 sda5 sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512. ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected sd 0:0:0:0: [sda] Attached SCSI disk ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 usbcore: registered new interface driver ums-usbat mice: PS/2 mouse device common for all mice i2c /dev entries driver adt7473 0-002e: adt7473 chip found md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com dm_crypt using the OCF package. usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Target Board is Marvell 6702. WIX LED GPIO Driver 1.1.4 TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 5 RPC: Registered udp transport module. RPC: Registered tcp transport module. Marvell Kirkwood Power Management Initializing registered taskstats version 1 rtc mv_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: invalid raid superblock magic on sda4 md: sda4 does not have a valid v0.90 superblock, not importing! md: Scanned 4 and added 3 devices. md: autorun ... md: considering sda3 ... md: adding sda3 ... md: sda2 has different UUID to sda3 md: sda1 has different UUID to sda3 md: created md2 md: bind md: running: raid1: raid set md2 active with 1 out of 2 mirrors md2: detected capacity change from 0 to 536805376 md: considering sda2 ... md: adding sda2 ... md: sda1 has different UUID to sda2 md: created md1 md: bind md: running: raid1: raid set md1 active with 1 out of 2 mirrors md1: detected capacity change from 0 to 4294901760 md: considering sda1 ... md: adding sda1 ... md: created md0 md: bind md: running: raid1: raid set md0 active with 1 out of 2 mirrors md0: detected capacity change from 0 to 2147418112 md: ... autorun DONE. RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 2660KiB [1 disk] into ram disk... done. VFS: Mounted root (cramfs filesystem) readonly on device 1:0. Freeing init memory: 140K Enter Pre-Root FileSystem: MODEL=TCC-C1 BAY_COUNT=1 DEVICE_LIST=sda FW_UPDATE_FLAG_RES:1 BOARDTEST_FLAG:0 Disk partition result:(0:parted, 1:non-parted) 1 33MB 2180MB 2147MB ext3 raid 2 2180MB 6475MB 4295MB linux-swap raid 3 6475MB 7012MB 537MB ext3 raid 4 7012MB 7012MB 66kB raid 5 7012MB 2000GB 1993GB primary DSK1_RES:0 Disk connect result: DSK1_S_RES:1 RAID5_CHK_RES:1 MD0_CHK_RES:0 FWUPDATE_CHK_RES:1 md0: unknown partition table /dev/md0: recovering journal /dev/md0 has gone 46461 days without being checked, check forced. /dev/md0: 23798/262144 files (1.4% non-contiguous), 120789/524272 blocks kjournald starting. Commit interval 5 seconds EXT3 FS on md0, internal journal EXT3-fs: mounted filesystem with writeback data mode. init started: BusyBox v1.1.1 (2008.10.08-08:58+0000) multi-call binary md2: unknown partition table kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on md2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. md1: unknown partition table Adding 2097136k swap on /dev/md1. Priority:-1 extents:1 across:2097136k Starting pid 710, console /dev/ttyS0: '/etc/init.d/rcS' ==> Starting udev ......................................... udevd version 125 started [ OK ] ==> Resetting clock from /etc/date.save ..................... Sun Oct 8 13:03:00 NZDT 2006 [ OK ] ==> Starting Network & HTTP Server ........................ egiga0: started [ OK ] ==> Activating VGs ........................................ [ OK ] ==> Assembling MD arrays .................................. md: md4 stopped. md: bind md4: detected capacity change from 0 to 1993384500736 md4: unknown partition table [ OK ] ==> Updating disk information ............................. [ OK ] EXT4-fs (md4): barriers disabled kjournald2 starting: pid 1396, dev md4:8, commit interval 5 seconds EXT4-fs (md4): internal journal on md4:8 EXT4-fs (md4): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (md4): recovery complete EXT4-fs (md4): mounted filesystem with ordered data mode [ OK ] ==> Mounting all shares with bind property ................ [ OK ] [ OK ] ==> Check if new client files need to be installed..........[ NO ] - Toshiba folder does not exist ==> Checking symbolic link for Toshiba client software......[ OK ] ==> Checking symbolic link for Toshiba introduction video...[ OK ] ==> Checking symbolic link for Toshiba introduction video for MAC...[ OK ] ==> Starting portmap ...................................... [ OK ] ==> Starting sshd ......................................... [ OK ] ==> Starting EventHandler ................................. [ OK ] ==> Starting HWMonitor .................................... [ OK ] ==> Starting smbd ......................................... [ OK ] ==> Starting nmbd ......................................... [ OK ] ==> Starting AppleTalk services ........................... Starting afpd:[ OK ] ==> Starting mDNSResponder ................................ [ OK ] ==> Starting NTP client ................................... [ OK ] ==> Starting mt-daapd ..................................... [ OK ] Starting /usr/twonky/twonkystarter ... Detaching from parent ==> Starting logrotate .................................... [ OK ] ==> Starting lltd for egiga0............................... [ OK ] ==> Starting WiAutoConfig ................................. [ OK ] ==> Starting crond ..........crond[1788]: crond: crond (busybox 1.17.2) started, log level 8 [ OK ] Starting Network Interface Plugging Daemon:Twonky Version 7.2.7 egiga0. ==> Starting LogOn ..................................... [ OK ] ==> Starting LogOn monitoring daemon ................... [ OK ] For image conversion and scaling the TwonkyServer utilizes ImageMagick. For details on the license please see /usr/twonky/cgi-bin/convert-readme.txt ==> Starting Dynamic DNS Updater .......................... ==> Starting rtorrent ..................................... [ OK ] ==> Starting button monitor ............................... [ OK ] ==> Printer's spooler is GOOD ............................. ==> Starting cupsd ........................................ Dynamic DNS service has been disabled. [ OK ] Starting Downloader's schedulerd ... ok ==> Set readahead 4096 for block device ................... [ OK ] ==> Starting syslogd ...................................... [ OK ] No personal TLS certificate found in /var/twonky/twonkyserver/tls.pem! Will use built-in keys (this is insecure)! You have been warned ... ==> Syncing time from system clock to H/W clock ........... [ OK ] ==> Deleting the critical event(s) ........................ [ OK ] ==> Starting I/O Monitor for HDD standby .................. ==> Starting Daemon Monitor for EventHandler and HWmonitor. ==> Checking whether system get abnormal shutdown ......... [ AB ] iomonitor[2056]: terminate iomonitor becasue HDD standby was disabled Starting pid 2436, console /dev/ttyS0: '/sbin/getty' Canvio-87f997ff login: