=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.11.01 19:34:50 =~=~=~=~=~=~=~=~=~=~=~= U-Boot 1.1.4 (Oct 1 2011 - 12:06:06) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006918B4 Soc: 88F6192 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A3 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME] Hit any key to stop autoboot: 1 0 CE>> CE>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes CASset=min MALLOC_len=1 ethprime=egiga0 load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 boot=bootm 0x800000 boot_nand=run load_nand boot || run load_nand2 boot ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 ethaddr=00:25:31:04:de:09 cesvcid=W7K4T5RWBR5WW7KC2WY49364YN ceboardver=PPV4A3 ipaddr=192.168.58.233 serverip=192.168.58.188 bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs bootcmd=run boot_nand stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=1 disaMvPnp=no hddPowerCtrl=no pcieTune=no Environment size: 834/131068 bytes CE>> help ? - alias for 'help' base - print or set address offset boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name bootm - boot application image from memory bootp- boot image via network using BootP/TFTP protocol bubt- Burn an image on the Boot Nand Flash. chpart- change active partition cmp - memory compare cmpm- Compare Memory cp - memory copy cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time dclk- Display the MV device CLKs. dhcp- invoke DHCP client to obtain IP/boot params diskboot- boot from IDE device echo - echo args to console eeprom - EEPROM sub-system erase - erase FLASH memory exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fi- Find value in the memory. flinfo - print FLASH memory information fsinfo- print information about filesystems fsload- load binary file from a filesystem image g- start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help icrc32 - checksum calculation ide - IDE sub-system iloop - infinite loop on address range imd - i2c memory display imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses ir- reading and changing MV internal register values. loop - infinite loop on address range ls- list files in a directory (default /) map- Diasplay address decode windows md - memory display me- PCI master enable mm - memory modify (auto-incrementing) mp- map PCI BAR mtdparts- define flash/nand partitions mtest - simple RAM test mv_diag - perform board diagnostics mv_diag - run all available tests mv_diag [1|2|...] - run specified test number mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nbubt- Burn a boot loader image on the Boot Nand Flash. nm - memory modify (constant address) pci - list and access PCI Configuration Space phyRead- Read PCI-E Phy register pciePhyWrite- Write PCI-E Phy register phyRead- Read Phy register phyWrite- Write Phy register ping- send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU resetenv- Return all environment variable to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage se- PCI Slave enable setenv - set environment variables sflash- read, write or erase the external SPI Flash. sg- scanning the PHYs status sp- Scan PCI bus. switchRegRead- Read switch register switchRegWrite- Write switch register test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol version - print monitor version CE>> boot Loading from NAND 128MB 3,3V 8-bit, offset 0x200000 Image Name: Linux-2.6.31.8 Created: 2011-09-28 19:09:20 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00800000 ... Image Name: Linux-2.6.31.8 Created: 2011-09-28 19:09:20 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................... done, booting the kernel. [ 0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #5 Wed Sep 28 12:09:12 PDT 2011 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Ignoring unrecognised tag 0x41004345 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) [ 0.230000] Mount-cache hash table entries: 512 [ 0.230000] CPU: Testing write buffer coherency: ok [ 0.230000] NET: Registered protocol family 16 [ 0.230000] Feroceon L2: Enabling L2 [ 0.230000] Feroceon L2: Cache support initialised. [ 0.230000] [ 0.230000] CPU Interface [ 0.230000] ------------- [ 0.230000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.230000] SDRAM_CS1 ....disable [ 0.230000] SDRAM_CS2 ....disable [ 0.230000] SDRAM_CS3 ....disable [ 0.230000] PEX0_MEM ....base e0000000, size 128MB [ 0.230000] PEX0_IO ....base f2000000, size 1MB [ 0.230000] PEX1_MEM ....no such [ 0.230000] PEX1_IO ....no such [ 0.230000] INTER_REGS ....base f1000000, size 1MB [ 0.230000] NFLASH_CS ....base fa000000, size 2MB [ 0.230000] SPI_CS ....base f4000000, size 16MB [ 0.230000] BOOT_ROM_CS ....no such [ 0.230000] DEV_BOOTCS ....no such [ 0.230000] CRYPT_ENG ....base f0000000, size 2MB [ 0.230000] [ 0.230000] Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- RD-88F6192A-NAS Soc: 88F6192 A1 LE [ 0.230000] [ 0.230000] Detected Tclk 166666667 and SysClk 200000000 [ 0.230000] Marvell USB EHCI Host controller #0: c403e740 [ 0.730000] PEX0 interface detected Link X1 [ 0.740000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 0.740000] pci 0000:00:01.0: PME# disabled [ 0.740000] PCI: bus0: Fast back to back transfers disabled [ 0.740000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 [ 0.750000] bio: create slab at 0 [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.750000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.750000] TCP reno registered [ 0.750000] NET: Registered protocol family 1 [ 0.750000] cpufreq: Init kirkwood cpufreq driver [ 0.760000] XOR registered 4 channels [ 0.760000] XOR 2nd invalidate WA enabled [ 0.760000] cesadev_init(c000d7fc) [ 0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.770000] msgmni has been set to 231 [ 0.770000] alg: No test for cipher_null (cipher_null-generic) [ 0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 0.770000] alg: No test for digest_null (digest_null-generic) [ 0.770000] alg: No test for compress_null (compress_null-generic) [ 0.780000] alg: No test for stdrng (krng) [ 0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic)) [ 0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.790000] io scheduler noop registered [ 0.790000] io scheduler anticipatory registered (default) [ 0.790000] Initializing ths8200_init [ 0.790000] Initializing dove_adi9889_init [ 0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.810000] console [ttyS0] enabled [ 0.820000] Integrated Sata device found [ 0.830000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs [ 0.850000] scsi0 : Marvell SCSI to SATA adapter [ 0.860000] scsi1 : Marvell SCSI to SATA adapter [ 0.870000] Loading Marvell Ethernet Driver: [ 0.870000] o Cached descriptors in DRAM [ 0.880000] o DRAM SW cache-coherency [ 0.880000] o 1 Giga ports supported [ 0.880000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.890000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.890000] o TCP segmentation offload (TSO) supported [ 0.900000] o Large Receive offload (LRO) supported [ 0.900000] o Receive checksum offload supported [ 0.910000] o Transmit checksum offload supported [ 0.910000] o Network Fast Processing (Routing) supported - (Disabled) [ 0.920000] o Driver ERROR statistics enabled [ 0.930000] o Proc tool API enabled [ 0.930000] o SKB Reuse supported - (Disabled) [ 0.930000] o SKB Recycle supported - (Disabled) [ 0.940000] o Rx descripors: q0=128 [ 0.940000] o Tx descripors: q0=532 [ 0.950000] o Loading network interface(s): [ 0.950000] o register under mv88fx_eth platform [ 0.960000] o eth0, ifindex = 2, GbE port = 0 [ 0.960000] [ 0.960000] mvFpRuleDb (c45b2000): 1024 entries, 4096 bytes [ 0.970000] Counter=0, opIdx=6, overhead=16 [ 0.970000] Counter=1, opIdx=2, overhead=0 [ 0.980000] Counter=2, opIdx=1, overhead=18 [ 0.980000] Counter=3, opIdx=2, overhead=0 [ 0.990000] tun: Universal TUN/TAP device driver, 1.6 [ 0.990000] tun: (C) 1999-2004 Max Krasnyansky [ 1.000000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.010000] Scanning device for bad blocks [ 1.010000] Bad eraseblock 4 at 0x000000080000 [ 1.050000] Bad eraseblock 697 at 0x000005720000 [ 1.070000] Using static partition definition [ 1.070000] Creating 5 MTD partitions on "nand_mtd": [ 1.070000] 0x000000000000-0x000000200000 : "u-boot" [ 1.080000] 0x000000200000-0x000000500000 : "uImage" [ 1.090000] 0x000000500000-0x000000800000 : "uImage2" [ 1.090000] 0x000000800000-0x000001000000 : "failsafe" [ 1.100000] 0x000001000000-0x000008000000 : "root" [ 1.100000] UBI: attaching mtd4 to ubi0 [ 1.110000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 1.110000] UBI: logical eraseblock size: 126976 bytes [ 1.120000] UBI: smallest flash I/O unit: 2048 [ 1.120000] UBI: sub-page size: 512 [ 1.130000] UBI: VID header offset: 2048 (aligned 2048) [ 1.130000] UBI: data offset: 4096 [ 1.360000] UBI: attached mtd4 to ubi0 [ 1.360000] UBI: MTD device name: "root" [ 1.370000] UBI: MTD device size: 112 MiB [ 1.370000] UBI: number of good PEBs: 895 [ 1.380000] UBI: number of bad PEBs: 1 [ 1.380000] UBI: max. allowed volumes: 128 [ 1.390000] UBI: wear-leveling threshold: 4096 [ 1.390000] UBI: number of internal volumes: 1 [ 1.400000] UBI: number of user volumes: 1 [ 1.400000] UBI: available PEBs: 0 [ 1.410000] UBI: total number of reserved PEBs: 895 [ 1.410000] UBI: number of PEBs reserved for bad PEB handling: 8 [ 1.420000] UBI: max/mean erase counter: 1/0 [ 1.420000] UBI: image sequence number: 0 [ 1.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.430000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.440000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.450000] UBI: background thread "ubi_bgt0d" started, PID 452 [ 1.480000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.500000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 [ 1.500000] usb usb1: configuration #1 chosen from 1 choice [ 1.510000] hub 1-0:1.0: USB hub found [ 1.510000] hub 1-0:1.0: 1 port detected [ 1.520000] xhci_hcd 0000:00:01.0: xHCI Host Controller [ 1.520000] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2 [ 1.530000] xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000 [ 1.540000] usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor [ 1.550000] usb usb2: configuration #1 chosen from 1 choice [ 1.550000] hub 2-0:1.0: USB hub found [ 1.560000] hub 2-0:1.0: 4 ports detected [ 1.560000] Initializing USB Mass Storage driver... [ 1.560000] usbcore: registered new interface driver usb-storage [ 1.570000] USB Mass Storage support registered. [ 1.580000] usbcore: registered new interface driver ums-datafab [ 1.580000] usbcore: registered new interface driver ums-freecom [ 1.590000] usbcore: registered new interface driver ums-jumpshot [ 1.590000] usbcore: registered new interface driver ums-sddr09 [ 1.600000] usbcore: registered new interface driver ums-sddr55 [ 1.610000] usbcore: registered new interface driver ums-usbat [ 1.610000] mice: PS/2 mouse device common for all mice [ 1.620000] i2c /dev entries driver [ 1.630000] sdhci: Secure Digital Host Controller Interface driver [ 1.630000] sdhci: Copyright(c) Pierre Ossman [ 1.640000] mmc0: mvsdio driver initialized, using GPIO 27 for card detection [ 1.650000] usbcore: registered new interface driver usbhid [ 1.650000] usbhid: v2.6:USB HID core driver [ 1.660000] TCP cubic registered [ 1.660000] NET: Registered protocol family 17 [ 1.670000] RPC: Registered udp transport module. [ 1.670000] RPC: Registered tcp transport module. [ 1.680000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.820000] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 1.820000] UBIFS: file system size: 110723072 bytes (108128 KiB, 105 MiB, 872 LEBs) [ 1.830000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) [ 1.840000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 1.840000] UBIFS: default compressor: lzo [ 1.850000] UBIFS: reserved for root: 0 bytes (0 KiB) [ 1.850000] VFS: Mounted root (ubifs filesystem) on device 0:11. [ 1.860000] Freeing init memory: 124K [ 4.230000] eth0: link down [ 4.230000] eth0: started udhcpc (v1.16.1) started HWADDR 00 0x25 0x31 0x04 0xde 0x09 PIP0 222 PIP1 9 cat: can't open '/etc/resolv.conf': No such file or directory route: SIOCDELRT: No such process grep: /etc/resolv.conf: No such file or directory Sending discover... [ 5.860000] eth0: link up, full duplex, speed 1 Gbps Sending discover... Sending select for 192.168.1.97... Lease of 192.168.1.97 obtained, lease time 86400 HWADDR 00 0x25 0x31 0x04 0xde 0x09 PIP0 222 PIP1 9 route: SIOCDELRT: No such process modprobe: module 'vfat' not found [ 7.910000] ufsd: module license 'Commercial product' taints kernel. [ 7.920000] Disabling lock debugging due to kernel taint [ 7.950000] ufsd: driver 8.5 (NTFS4LINUX_U85_017_S[2011-08-17-16:51:48]) LBD=ON with delayalloc with ioctl loaded at bf000000 [ 7.950000] NTFS support included [ 7.950000] Hfs+/HfsX support included [ 7.950000] For 'CloudEngines_PogoPlug_2011-08-03' Loading rt3070sta.ko: [ 8.280000] rtusb init rt2870 ---> [ 8.290000] usbcore: registered new interface driver rt2870 Success Loading xce.ko: [ 8.320000] Cloud Engines XCE Init [Version: 3.1.99.12] [ 8.320000] XCE: CPU MEMORY MAP: [ 8.320000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings [ 8.330000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space [ 8.340000] XCE: -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram [ 8.350000] XCE: -- 0xc8800000 - 0xe7ffffff ( 504 MB) Kernel vmalloc space [ 8.350000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space [ 8.360000] XCE: CPU FEATURES: [ 8.360000] XCE: -- I Cache: enabled [ 8.370000] XCE: -- D Cache: enabled [ 8.370000] XCE: -- Branch Predict: disabled [ 8.380000] XCE: -- MMU: enabled [ 8.380000] XCE: -- Alignment Abort: enabled [ 8.390000] XCE: BLPARAMS: -- Loading properties [c4c2defc]. [ 8.400000] XCE: BLPARAMS: -- MTD @ [c45c1c00]. [ 8.400000] XCE: BLPARAMS: Locating parameter block... [ 8.410000] XCE: BLPARAMS: reading 2048 bytes @ a0000 [ 8.410000] XCE: Loaded Property Size: 2048 [ 8.420000] XCE: - 'cesvcid' -> 'W7K4T5RWBR5WW7KC2WY49364YN' [ 8.420000] XCE: - 'ceboardver' -> 'PPV4A3' [ 8.430000] XCE: -- ICache Prefetch: enabled [ 8.430000] XCE: -- DCache Prefetch: enabled [ 8.440000] XCE: -- L2 Cache: enabled [ 8.440000] XCE: -- L2 Prefetch: disabled [ 8.440000] XCE: -- L2 Writethrough: disabled [ 8.450000] XCE: -- Write Allocate: disabled [ 8.450000] XCE: -- Streaming: disabled [ 8.460000] XCE: Current GPIO State: [ 8.460000] XCE: GPIO L OUT: 0x01f18400 [ 8.470000] XCE: GPIO L OE: 0xfe004800 [ 8.470000] XCE: GPIO L BLINK: 0x00000000 [ 8.470000] XCE: GPIO L POL: 0x08000000 [ 8.480000] XCE: GPIO L IN: 0x31f00000 [ 8.480000] XCE: GPIO H OUT: 0x00000008 [ 8.490000] XCE: GPIO H OE: 0x00000005 [ 8.490000] XCE: GPIO H BLINK: 0x00000000 [ 8.500000] XCE: GPIO H POL: 0x00000000 [ 8.500000] XCE: GPIO H IN: 0x00000008 Success Starting hbplug: Success / # [ 8.580000] XCE: BLPARAMS: -- Loading properties [c4c23ecc]. [ 8.590000] XCE: BLPARAMS: -- MTD @ [c45c1c00]. [ 8.590000] XCE: BLPARAMS: Locating parameter block... [ 8.600000] XCE: BLPARAMS: reading 2048 bytes @ a0000 [ 8.610000] XCE: BLPARAMS: reading 2048 bytes @ a0800 [ 8.610000] XCE: BLPARAMS: reading 2048 bytes @ a1000 [ 8.620000] XCE: BLPARAMS: reading 2048 bytes @ a1800 [ 13.900000] XCE: XCE: LED -> CONNECTED / # login Pogoplug login: root Password: login[676]: root login on 'console' ~ # halt The system is going down NOW! Sent SIGTERM to all processes Terminated ~ # Sent SIGKILL to[ 52.150000] System halted.