__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.1 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Toggle power status Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found CPU : Marvell Feroceon (Rev 1) Found initrd at 0x2d8000 Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST3120827AS Rev: 3.42 Type: Hard Disk Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> scsi scan scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST3120827AS Rev: 3.42 Type: Hard Disk Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) Marvell>> setenv hdd_make_boot_args 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) earlyprintk=serial' Marvell>> setenv load_initrd 'ext2load scsi 0:2 0x2100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load scsi 0:2 0x40000 /boot/uImage' Marvell>> setenv hdd_boot 'scsi start; run load_uimage; run load_initrd; bootm 0x40000 0x2100000' Marvell>> setenv bootcmd 'scsi scan; scsi dev 0; run hdd_make_boot_args ; run hdd_boot; reset' Marvell>> boot scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST3120827AS Rev: 3.42 Type: Hard Disk Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST3120827AS Rev: 3.42 Type: Hard Disk Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) ... is now current device Usage: scsi - SCSI sub-system 4074874 bytes read 8014099 bytes read ## Booting image at 00040000 ... Image Name: Linux-4.16.1-kirkwood-tld-1 Created: 2018-06-23 16:02:47 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4074810 Bytes = 3.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC �