nc -l -u -p 6666 U-Boot 2011.12 (Apr 18 2012 - 23:08:20) Seagate GoFlexNet arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1750 UBI: number of bad PEBs: 2 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1729 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST1500LM003-9YH148 Firm: CC94 Ser#: Z110090P Type: Hard Disk Supports 48-bit addressing Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512) Loading file "/boot/uImage" from ide device 0:1 (hda1) 2279256 bytes read Loading file "/boot/uInitrd" from ide device 0:1 (hda1) 6996346 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2279192 Bytes = 2.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.3.2-kirkwood-dg Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6996282 Bytes = 6.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... U-Boot 2011.12 (Apr 18 2012 - 23:08:20) Seagate GoFlexNet arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1750 UBI: number of bad PEBs: 2 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1729 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST1500LM003-9YH148 Firm: CC94 Ser#: Z110090P Type: Hard Disk Supports 48-bit addressing Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512) Loading file "/boot/uImage" from ide device 0:1 (hda1) 1720272 bytes read Loading file "/boot/uInitrd" from ide device 0:1 (hda1) 6941601 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.6.6 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1720208 Bytes = 1.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6941537 Bytes = 6.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...