U-Boot 2013.07 (Sep 20 2013 - 15:45:03) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 12568 bytes read in 312 ms (39.1 KiB/s) 4192888 bytes read in 350 ms (11.4 MiB/s) 8157136 bytes read in 500 ms (15.6 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.19.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4192824 Bytes = 4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.19.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 8157072 Bytes = 7.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f376000, end 0fb3d790 ... OK Loading Device Tree to 0f36f000, end 0f375117 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.0-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Mon Oct 22 17:08:01 PDT 2018 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NSA310 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] random: get_random_bytes called from start_kernel+0x78/0x4e4 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sdb1 rootdelay=5 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 238428K/262144K available (8192K kernel code, 800K rwdata, 2172K rodata, 1024K init, 280K bss, 23716K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (9184 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 801 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 281 kB) [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000045] Switching to timer-based delay loop, resolution 5ns [ 0.000622] Console: colour dummy device 80x30 [ 0.000675] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000701] pid_max: default: 32768 minimum: 301 [ 0.001038] Security Framework initialized [ 0.001195] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001220] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002283] CPU: Testing write buffer coherency: ok [ 0.003811] Setting up static identity map for 0x100000 - 0x100058 [ 0.004112] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.004365] rcu: Hierarchical SRCU implementation. [ 0.007927] devtmpfs: initialized [ 0.013607] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.013644] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.013968] prandom: seed boundary self test passed [ 0.018154] prandom: 100 self tests passed [ 0.018166] pinctrl core: initialized pinctrl subsystem [ 0.019504] NET: Registered protocol family 16 [ 0.019940] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.020855] audit: initializing netlink subsys (disabled) [ 0.022093] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1 [ 0.022206] cpuidle: using governor ladder [ 0.022277] cpuidle: using governor menu [ 0.022752] Feroceon L2: Enabling L2 [ 0.022800] Feroceon L2: Cache support initialised. [ 0.028006] No ATAGs? [ 0.036767] vgaarb: loaded [ 0.037113] SCSI subsystem initialized [ 0.037571] usbcore: registered new interface driver usbfs [ 0.037634] usbcore: registered new interface driver hub [ 0.037692] usbcore: registered new device driver usb [ 0.037881] pps_core: LinuxPPS API ver. 1 registered [ 0.037892] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.037926] PTP clock support registered [ 0.038863] clocksource: Switched to clocksource orion_clocksource [ 0.140886] VFS: Disk quotas dquot_6.6.0 [ 0.140993] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.150672] NET: Registered protocol family 2 [ 0.151481] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.151512] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.151547] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.151578] TCP: Hash tables configured (established 2048 bind 2048) [ 0.151670] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.151696] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.151906] NET: Registered protocol family 1 [ 0.152497] RPC: Registered named UNIX socket transport module. [ 0.152510] RPC: Registered udp transport module. [ 0.152518] RPC: Registered tcp transport module. [ 0.152525] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.152788] Unpacking initramfs... [ 0.879535] Freeing initrd memory: 7968K [ 0.879665] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.880866] Initialise system trusted keyrings [ 0.880926] Key type blacklist registered [ 0.881139] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.881246] zbud: loaded [ 0.882241] NFS: Registering the id_resolver key type [ 0.882268] Key type id_resolver registered [ 0.882278] Key type id_legacy registered [ 0.882297] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.882308] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.882593] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.882801] fuse init (API version 7.27) [ 0.883188] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.883383] orangefs_init: module version upstream loaded [ 0.883395] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 2.558871] random: fast init done [ 6.813089] Key type asymmetric registered [ 6.813106] Asymmetric key parser 'x509' registered [ 6.813169] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 6.813182] io scheduler noop registered [ 6.813191] io scheduler deadline registered [ 6.813303] io scheduler cfq registered (default) [ 6.814712] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.816548] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 6.816569] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.816584] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.816597] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 6.818186] PCI: bus0: Fast back to back transfers disabled [ 6.818213] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.818656] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 7.876 Gb/s with 8 GT/s x1 link) [ 6.850161] PCI: bus1: Fast back to back transfers disabled [ 6.850394] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 6.850412] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 6.850432] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 6.850450] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 6.850475] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 6.850499] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 6.850517] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.850531] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 6.850548] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 6.850663] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 6.851255] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.909681] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.909923] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.969669] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.970127] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.971404] console [ttyS0] disabled [ 6.971476] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 7.719137] console [ttyS0] enabled [ 7.729689] loop: module loaded [ 7.733422] sata_mv f1080000.sata: slots 32 ports 2 [ 7.741005] scsi host0: sata_mv [ 7.744617] scsi host1: sata_mv [ 7.747964] ata1: SATA max UDMA/133 irq 32 [ 7.752148] ata2: SATA max UDMA/133 irq 32 [ 7.757053] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 7.763551] nand: Samsung NAND 128MiB 3,3V 8-bit [ 7.768190] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.775829] Scanning device for bad blocks [ 7.780220] Bad eraseblock 2 at 0x000000040000 [ 7.784735] Bad eraseblock 3 at 0x000000060000 [ 7.888305] 9 fixed-partitions partitions found on MTD device orion_nand [ 7.895060] Creating 9 MTD partitions on "orion_nand": [ 7.900253] 0x000000000000-0x000000100000 : "uboot" [ 7.906171] 0x000000100000-0x000000180000 : "uboot_env" [ 7.912435] 0x000000180000-0x000000200000 : "key_store" [ 7.918590] 0x000000200000-0x000000280000 : "info" [ 7.924360] 0x000000280000-0x000000c80000 : "etc" [ 7.930105] 0x000000c80000-0x000001680000 : "kernel_1" [ 7.936222] 0x000001680000-0x000004640000 : "rootfs1" [ 7.942618] 0x000004640000-0x000005040000 : "kernel_2" [ 7.948774] 0x000005040000-0x000008000000 : "rootfs2" [ 7.956236] libphy: Fixed MDIO Bus: probed [ 7.961117] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.967695] ehci-pci: EHCI PCI platform driver [ 7.972245] ehci-orion: EHCI orion driver [ 7.976468] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.982072] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.990011] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 8.018892] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.025215] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 8.033572] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.040871] usb usb1: Product: EHCI Host Controller [ 8.045775] usb usb1: Manufacturer: Linux 4.19.0-kirkwood-tld-1 ehci_hcd [ 8.052546] usb usb1: SerialNumber: f1050000.ehci [ 8.057900] hub 1-0:1.0: USB hub found [ 8.061769] hub 1-0:1.0: 1 port detected [ 8.066427] usbcore: registered new interface driver usb-storage [ 8.072930] mousedev: PS/2 mouse device common for all mice [ 8.079174] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 8.086275] i2c /dev entries driver [ 8.093199] hidraw: raw HID events driver (C) Jiri Kosina [ 8.099006] drop_monitor: Initializing network drop monitor service [ 8.105607] NET: Registered protocol family 17 [ 8.110187] Key type dns_resolver registered [ 8.115209] registered taskstats version 1 [ 8.119362] Loading compiled-in X.509 certificates [ 8.124253] zswap: loaded using pool lzo/zbud [ 8.150972] Key type big_key registered [ 8.164893] Key type encrypted registered [ 8.171056] rtc-mv f1010300.rtc: setting system clock to 2019-02-19 21:54:27 UTC (1550613267) [ 8.258909] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 8.269764] ata1.00: ATA-9: ST2000DM001-1CH164, CC27, max UDMA/133 [ 8.275975] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.287727] ata1.00: configured for UDMA/133 [ 8.302562] scsi 0:0:0:0: Direct-Access ATA ST2000DM001-1CH1 CC27 PQ: 0 ANSI: 5 [ 8.311718] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 8.320016] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 8.325392] sd 0:0:0:0: [sda] Write Protect is off [ 8.330408] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.362726] sda: sda1 sda2 [ 8.367107] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.428893] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.630640] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 8.638908] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.646119] usb 1-1: Product: USB2.0 Hub [ 8.650920] hub 1-1:1.0: USB hub found [ 8.654735] ata2: SATA link down (SStatus 0 SControl F300) [ 8.660644] hub 1-1:1.0: 4 ports detected [ 8.673420] Freeing unused kernel memory: 1024K [ 8.678597] Checked W+X mappings: passed, no W+X pages found [ 8.684320] Run /init as init process Loading, please wait... starting version 232 [ 8.788646] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 8.806424] random: udevadm: uninitialized urandom read (16 bytes read) [ 8.813959] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 8.978958] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 9.158294] usb 1-1.3: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01 [ 9.174787] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.188595] usb 1-1.3: Product: DataTraveler 3.0 [ 9.198570] usb 1-1.3: Manufacturer: Kingston [ 9.207932] usb 1-1.3: SerialNumber: C03FD5F2F2C2F160F9A4010A [ 9.220026] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 9.235478] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 9.241677] scsi host2: usb-storage 1-1.3:1.0 [ 9.287800] libphy: r8169: probed [ 9.293316] r8169 0000:01:00.0 eth0: RTL8168d/8111d, 00:00:00:00:00:30, XID 283000c0, IRQ 35 [ 9.338351] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 9.769993] usbcore: registered new interface driver uas [ 9.808411] r8169 0000:01:00.0 enp1s0: renamed from eth0 Begin: Loading essential drivers ... done. [ 10.249995] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6 [ 10.264084] sd 2:0:0:0: [sdb] 15109516 512-byte logical blocks: (7.74 GB/7.20 GiB) [ 10.279001] sd 2:0:0:0: [sdb] Write Protect is off [ 10.288996] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 10.310524] sdb: sdb1 [ 10.318814] sd 2:0:0:0: [sdb] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /dev/sdb1] fsck.ext3 -a -C0 /dev/sdb1 rootfs: clean, 87399/472352 files, 571968/1888256 blocks done. [ 15.055232] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 15.072052] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...[ 17.170831] input: gpio_keys as /devices/platform/gpio_keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 17.663978] orion_wdt: Initial timeout 21 sec [ 17.682020] hwmon_vid: Unknown VRM version of your CPU [ 17.687233] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 17.735537] marvell-cesa f1030000.crypto: CESA device successfully registered [ 17.784222] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 17.828739] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 17.854655] adt7475 0-002e: ADT7476 device, revision 1 [ 17.878052] adt7475 0-002e: Optional features: in0 in4 pwm2 vid [ 17.917061] adt7475 0-002e: Bypassing attenuators on: in0 in1 [ 18.315122] random: crng init done [ 18.318554] random: 7 urandom warning(s) missed due to ratelimiting done. [ ok ] Activating swap:. [ 19.207990] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 21.965189] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168d-2.fw failed with error -2 [ 21.974490] r8169 0000:01:00.0 enp1s0: unable to load firmware patch rtl_nic/rtl8168d-2.fw (-2) [ 21.983829] RTL8211B Gigabit Ethernet r8169-100:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-100:00, irq=IGNORE) [ 22.140876] r8169 0000:01:00.0 enp1s0: Link is Down [ 22.679257] NET: Registered protocol family 10 [ 22.687885] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 22.694200] Segment Routing with IPv6 [ 24.546954] r8169 0000:01:00.0 enp1s0: Link is Up - 1Gbps/Full - flow control rx/tx [ 24.554703] IPv6: ADDRCONF(NETDEV_CHANGE): enp1s0: link becomes ready [ ok ] Configuring network interfaces...done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1308 (syslogd) . ok [warn] Not starting motion daemon, disabled via /etc/default/motion ... (warning). [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1307 (klogd) . ok [warn] Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools ... (warning). [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: