▒ __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: SHEEVA PLUG LE U-Boot 1.1.4 (May 13 2009 - 13:10:52) Marvell version: 3.4.16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF100 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:512 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... cannot reset port 1!? 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Bad partition 1 ** ## Booting image at 00800000 ... Bad Magic Number NAND read: device 0 offset 0x100000, size 0x400000 Reading data from 0x4ff800 -- 100% complete. 4194304 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.30-rc6 Created: 2009-05-20 11:42:10 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2595144 Bytes = 2.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux........................................................................................................................................................................ done, booting the kernel. Linux version 2.6.30-rc6 (kelly@speedy) (gcc version 4.2.1) #2 PREEMPT Wed May 20 05:42:04 MDT 2009 CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: Marvell SheevaPlug Reference Board Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs NR_IRQS:114 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 256MB 256MB = 512MB total Memory: 513408KB available (4680K code, 998K data, 140K init, 0K highmem) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 980 bytes NET: Registered protocol family 16 Kirkwood: MV88F6281-A0, TCLK=200000000. Feroceon L2: Enabling L2 Feroceon L2: Cache support initialised. Kirkwood: Gating clock using mask 0x1ac224 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. JFS: nTxBlock = 4013, nTxLock = 32104 msgmni has been set to 1003 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A console [ttyS0] enabled brd: module loaded loop: module loaded Driver 'sd' needs updating - please use bus_type methods MV-643xx 10/100/1000 ethernet driver version 1.4 mv643xx_eth smi: probed net eth0: port 0 with MAC address 00:50:43:01:d4:ed libertas_sdio: Libertas SDIO driver libertas_sdio: Copyright Pierre Ossman NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 1320 at 0x00000a500000 Bad eraseblock 1321 at 0x00000a520000 Bad eraseblock 2042 at 0x00000ff40000 Bad eraseblock 2186 at 0x000011140000 Bad eraseblock 2196 at 0x000011280000 Bad eraseblock 2212 at 0x000011480000 Bad eraseblock 2213 at 0x0000114a0000 Bad eraseblock 2608 at 0x000014600000 Bad eraseblock 3413 at 0x00001aaa0000 Bad eraseblock 3419 at 0x00001ab60000 Bad eraseblock 3654 at 0x00001c8c0000 Bad eraseblock 3657 at 0x00001c920000 Bad eraseblock 3658 at 0x00001c940000 Bad eraseblock 3663 at 0x00001c9e0000 2 cmdlinepart partitions found on MTD device orion_nand Creating 2 MTD partitions on "orion_nand": 0x000000100000-0x000000500000 : "uImage" 0x000000500000-0x000020000000 : "rootfs" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "rootfs" UBI: MTD device size: 507 MiB UBI: number of good PEBs: 4042 UBI: number of bad PEBs: 14 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 4042 UBI: number of PEBs reserved for bad PEB handling: 40 UBI: max/mean erase counter: 24/2 UBI: background thread "ubi_bgt0d" started, PID 444 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver orion-ehci orion-ehci.0: Marvell Orion EHCI orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 mice: PS/2 mouse device common for all mice rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0 i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mmc0: mvsdio driver initialized, lacking card detect (fall back to polling) Registered led device: plug:green:health mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver oprofile: using timer interrupt. TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. lib80211: common routines for IEEE802.11 drivers rtc-mv rtc-mv: setting system clock to 2034-02-06 12:57:15 UTC (2022843435) UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 513902592 bytes (501858 KiB, 490 MiB, 3983 LEBs) UBIFS: journal size: 25675776 bytes (25074 KiB, 24 MiB, 199 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 4952683 bytes (4836 KiB) VFS: Mounted root (ubifs filesystem) on device 253:1. Freeing init memory: 140K usb 1-1: new high speed USB device using orion-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices * Setting preliminary keymap... [ OK ] * Setting the system clock Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. * Unable to set System Clock to: Mon Feb 6 12:57:17 UTC 2034 * Starting basic networking... [ OK ] * Starting kernel event manager... [ OK ] * Loading hardware drivers... uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0 Buffer I/O error on device mtdblock0, logical block 0 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 8 Buffer I/O error on device mtdblock0, logical block 1 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 16 Buffer I/O error on device mtdblock0, logical block 2 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 24 Buffer I/O error on device mtdblock0, logical block 3 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0 Buffer I/O error on device mtdblock0, logical block 0 [ OK ] * Setting the system clock * Loading kernel modules... * Loading manual drivers... [ OK ] * Setting kernel variables (/etc/sysctl.conf)... [ OK ] * Setting kernel variables (/etc/sysctl.d/10-console-messages.conf)... [ OK ] * Setting kernel variables (/etc/sysctl.d/10-network-security.conf)... [ OK ] * Setting kernel variables (/etc/sysctl.d/10-process-security.conf)... error: "vm.mmap_min_addr" is an unknown key [fail] sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through * Setting kernel variables (/etc/sysctl.d/10-tcp-timestamps-workaround.conf)... [ OK ] * Activating swap... [ OK ] * Starting early crypto disks... [ OK ] * Starting remaining crypto disks... [ OK ] * Checking file systems... fsck 1.41.3 (12-uncorrectable error : Oct-2008) <3>end_request: I/O error, dev mtdblock0, sector 8064 Buffer I/O error on device mtdblock0, logical block 1008 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 8064 Buffer I/O error on device mtdblock0, logical block 1008 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0 Buffer I/O error on device mtdblock0, logical block 0 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 8 Buffer I/O error on device mtdblock0, logical block 1 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 16 Buffer I/O error on device mtdblock0, logical block 2 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 24 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 32 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 40 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 48 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 56 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 64 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 72 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 80 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 88 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 96 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 104 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 112 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 120 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 528 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 528 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 528 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 8064 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 8064 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 8 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 16 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 24 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 32 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 40 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 48 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 56 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 64 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 72 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 80 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 88 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 96 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 104 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 112 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 120 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 528 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 528 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 528 [ OK ] * Mounting local filesystems... [ OK ] * Activating swapfile swap... [ OK ] * Configuring network interfaces... [ OK ] * Setting up console font and keymap... [ OK ] * Starting system log daemon... Ubuntu jaunty (development branch) TonidoPlug ttyS0 TonidoPlug login: [ OK ] * Starting kernel log daemon... [ OK ] * Starting OpenBSD Secure Shell server sshd [ OK ] * Starting Samba daemons [ OK ] * Starting uShare UPnP A/V & DLNA Media Server: ushare * No shares avalaible ... [ OK ] * Starting periodic command scheduler crond [ OK ] Ubuntu jaunty (development branch) TonidoPlug ttyS0 TonidoPlug login: