U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:42:03 -0700) ZyXEL NSA325 2-Bay Power Media Server SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x007757de "" attrs: 0x0000000000000000 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 425f4919-edd8-434f-a0bd-9a078de96a5f ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 691 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4963680 bytes read in 1049 ms (4.5 MiB/s) loading uInitrd ... 9713936 bytes read in 1040 ms (8.9 MiB/s) loading DTB /boot/dts/kirkwood-nsa325.dtb ... 14006 bytes read in 1553 ms (8.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4963616 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 1f1ca000, end 1fb0d8d0 ... OK Loading Device Tree to 1f1c3000, end 1f1c96b5 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: ZyXEL NSA325 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000][ T0] Memory: 494676K/524288K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 29612K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000039][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000643][ T0] Console: colour dummy device 80x30 [ 0.000685][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000709][ T0] pid_max: default: 32768 minimum: 301 [ 0.001012][ T0] LSM: Security Framework initializing [ 0.001159][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001181][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001878][ T0] *** VALIDATE proc *** [ 0.002098][ T0] *** VALIDATE cgroup1 *** [ 0.002120][ T0] *** VALIDATE cgroup2 *** [ 0.002204][ T0] CPU: Testing write buffer coherency: ok [ 0.003664][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.003923][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.004164][ T1] rcu: Hierarchical SRCU implementation. [ 0.006801][ T1] devtmpfs: initialized [ 0.012219][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.012246][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.012460][ T1] xor: measuring software checksum speed [ 0.110098][ T1] arm4regs : 1453.200 MB/sec [ 0.210060][ T1] 8regs : 872.400 MB/sec [ 0.310062][ T1] 32regs : 1266.800 MB/sec [ 0.310079][ T1] xor: using function: arm4regs (1453.200 MB/sec) [ 0.310097][ T1] prandom: seed boundary self test passed [ 0.313231][ T1] prandom: 100 self tests passed [ 0.313240][ T1] pinctrl core: initialized pinctrl subsystem [ 0.314471][ T1] NET: Registered protocol family 16 [ 0.314889][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.315530][ T1] audit: initializing netlink subsys (disabled) [ 0.316579][ T14] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.316682][ T1] cpuidle: using governor ladder [ 0.316748][ T1] cpuidle: using governor menu [ 0.317200][ T1] Feroceon L2: Enabling L2 [ 0.317241][ T1] Feroceon L2: Cache support initialised. [ 0.322041][ T1] No ATAGs? [ 2.560045][ C0] random: fast init done [ 4.743620][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 4.743901][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 4.920464][ T1] raid6: int32x8 gen() 171 MB/s [ 5.090148][ T1] raid6: int32x8 xor() 115 MB/s [ 5.260332][ T1] raid6: int32x4 gen() 172 MB/s [ 5.430158][ T1] raid6: int32x4 xor() 112 MB/s [ 5.600051][ T1] raid6: int32x2 gen() 177 MB/s [ 5.770047][ T1] raid6: int32x2 xor() 125 MB/s [ 5.940334][ T1] raid6: int32x1 gen() 134 MB/s [ 6.110340][ T1] raid6: int32x1 xor() 92 MB/s [ 6.110350][ T1] raid6: using algorithm int32x2 gen() 177 MB/s [ 6.110357][ T1] raid6: .... xor() 125 MB/s, rmw enabled [ 6.110363][ T1] raid6: using intx1 recovery algorithm [ 6.110590][ T1] vgaarb: loaded [ 6.111000][ T1] SCSI subsystem initialized [ 6.111406][ T1] usbcore: registered new interface driver usbfs [ 6.111454][ T1] usbcore: registered new interface driver hub [ 6.111522][ T1] usbcore: registered new device driver usb [ 6.111667][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.111676][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 6.111697][ T1] PTP clock support registered [ 6.112744][ T1] clocksource: Switched to clocksource orion_clocksource [ 6.886747][ T1] VFS: Disk quotas dquot_6.6.0 [ 6.886832][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 6.894345][ T1] NET: Registered protocol family 2 [ 6.895014][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 6.895044][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 6.895098][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 6.895150][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 6.895225][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 6.895248][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 6.895433][ T1] NET: Registered protocol family 1 [ 6.895969][ T1] RPC: Registered named UNIX socket transport module. [ 6.895980][ T1] RPC: Registered udp transport module. [ 6.895987][ T1] RPC: Registered tcp transport module. [ 6.895993][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.896005][ T1] PCI: CLS 0 bytes, default 32 [ 6.896200][ T1] Trying to unpack rootfs image as initramfs... [ 7.540235][ T1] Freeing initrd memory: 9488K [ 7.540390][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 7.541429][ T1] Initialise system trusted keyrings [ 7.541474][ T1] Key type blacklist registered [ 7.541665][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 7.541756][ T1] zbud: loaded [ 7.542641][ T1] NFS: Registering the id_resolver key type [ 7.542669][ T1] Key type id_resolver registered [ 7.542676][ T1] Key type id_legacy registered [ 7.542693][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 7.542707][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.543010][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 7.543195][ T1] fuse: init (API version 7.31) [ 7.543544][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 7.543693][ T1] orangefs_init: module version upstream loaded [ 7.543703][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 7.557313][ T1] async_tx: api initialized (async) [ 7.557334][ T1] Key type asymmetric registered [ 7.557342][ T1] Asymmetric key parser 'x509' registered [ 7.557406][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 7.558570][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 7.560101][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 7.560121][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 7.560133][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 7.560143][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 7.560246][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 7.560280][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 7.561484][ T1] PCI: bus0: Fast back to back transfers disabled [ 7.561505][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 7.561664][ T1] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330 [ 7.561712][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 7.561854][ T1] pci 0000:01:00.0: PME# supported from D0 D3hot [ 7.561921][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 7.583849][ T1] PCI: bus1: Fast back to back transfers disabled [ 7.583871][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 7.584029][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 7.584044][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 7.584059][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] [ 7.584081][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 7.584095][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 7.584188][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 7.584255][ T1] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 7.584723][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 7.643403][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 7.644939][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 7.703361][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 7.705148][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 7.706200][ T1] printk: console [ttyS0] disabled [ 7.706263][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 8.628337][ T1] printk: console [ttyS0] enabled [ 8.639140][ T1] loop: module loaded [ 8.643532][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 8.651261][ T1] scsi host0: sata_mv [ 8.655609][ T1] scsi host1: sata_mv [ 8.659699][ T1] ata1: SATA max UDMA/133 irq 32 [ 8.664562][ T1] ata2: SATA max UDMA/133 irq 32 [ 8.670194][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 8.677379][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 8.682365][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 8.690692][ T1] Scanning device for bad blocks [ 8.695600][ T1] 9 cmdlinepart partitions found on MTD device orion_nand [ 8.702594][ T1] Creating 9 MTD partitions on "orion_nand": [ 8.708468][ T1] 0x000000000000-0x000000100000 : "uboot" [ 8.715125][ T1] 0x000000100000-0x000000180000 : "stock_uboot_env" [ 8.722553][ T1] 0x000000180000-0x000000200000 : "key_store" [ 8.729497][ T1] 0x000000200000-0x000000280000 : "info" [ 8.735986][ T1] 0x000000280000-0x000000c80000 : "etc" [ 8.742362][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 8.749245][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 8.756118][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 8.762984][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 8.770775][ T1] libphy: Fixed MDIO Bus: probed [ 8.776262][ T1] libphy: orion_mdio_bus: probed [ 8.792480][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 8.800461][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 8.807824][ T1] mv643xx_eth: Set the PHY to fix link down [ 8.808303][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 8.823722][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.831001][ T1] ehci-pci: EHCI PCI platform driver [ 8.836255][ T1] ehci-orion: EHCI orion driver [ 8.841135][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 8.847419][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 8.855972][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 8.882774][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.889724][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 8.898769][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.906759][ T1] usb usb1: Product: EHCI Host Controller [ 8.912375][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 8.919744][ T1] usb usb1: SerialNumber: f1050000.ehci [ 8.925661][ T1] hub 1-0:1.0: USB hub found [ 8.930157][ T1] hub 1-0:1.0: 1 port detected [ 8.935490][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 8.941489][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 8.949933][ T1] xhci_hcd 0000:01:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 8.960176][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 8.969216][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.977202][ T1] usb usb2: Product: xHCI Host Controller [ 8.982827][ T1] usb usb2: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd [ 8.990184][ T1] usb usb2: SerialNumber: 0000:01:00.0 [ 8.995990][ T1] hub 2-0:1.0: USB hub found [ 9.000486][ T1] hub 2-0:1.0: 2 ports detected [ 9.005270][ T112] ata1: SATA link down (SStatus 0 SControl F300) [ 9.011969][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 9.017989][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 9.026267][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 9.033369][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 9.042330][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02 [ 9.051429][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.059402][ T1] usb usb3: Product: xHCI Host Controller [ 9.065015][ T1] usb usb3: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd [ 9.072359][ T1] usb usb3: SerialNumber: 0000:01:00.0 [ 9.078148][ T1] hub 3-0:1.0: USB hub found [ 9.082645][ T1] hub 3-0:1.0: 2 ports detected [ 9.088006][ T1] usbcore: registered new interface driver usb-storage [ 9.095067][ T1] mousedev: PS/2 mouse device common for all mice [ 9.101592][ T1] i2c /dev entries driver [ 9.108460][ T1] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. [ 9.116925][ T1] rtc-pcf8563 0-0051: registered as rtc0 [ 9.124056][ T1] device-mapper: uevent: version 1.0.3 [ 9.129634][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 9.139157][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 9.146472][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 9.153957][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 9.161359][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 9.168201][ T1] device-mapper: raid: Loading target version 1.14.0 [ 9.176396][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 9.182814][ T1] drop_monitor: Initializing network drop monitor service [ 9.190058][ T1] NET: Registered protocol family 17 [ 9.195528][ T1] Key type dns_resolver registered [ 9.201402][ T1] registered taskstats version 1 [ 9.206250][ T1] Loading compiled-in X.509 certificates [ 9.211859][ T1] zswap: loaded using pool lzo/zbud [ 9.289744][ T1] Key type big_key registered [ 9.302835][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 9.335317][ T1] Key type encrypted registered [ 9.342904][ T1] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. [ 9.351064][ T1] rtc-pcf8563 0-0051: hctosys: unable to read the hardware clock [ 9.363793][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 9.383169][ T1] Freeing unused kernel memory: 1024K [ 9.388892][ T1] Checked W+X mappings: passed, no W+X pages found [ 9.395302][ T1] Run /init as init process Loading, please wait... [ 9.504744][ T15] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 Starting version 241 [ 9.535344][ T15] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 9.543358][ T15] usb 1-1: Product: USB2.0 Hub [ 9.563428][ T15] hub 1-1:1.0: USB hub found [ 9.572836][ T15] hub 1-1:1.0: 4 ports detected [ 9.902836][ T15] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 10.073989][ T15] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.26 [ 10.090380][ T15] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.115269][ T15] usb 1-1.2: Product: Cruzer Blade [ 10.120259][ T15] usb 1-1.2: Manufacturer: SanDisk [ 10.139019][ T15] usb 1-1.2: SerialNumber: 20043513420EDF10DA1B [ 10.152324][ T15] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 10.171873][ T15] scsi host2: usb-storage 1-1.2:1.0 [ 10.534256][ T161] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. [ 11.203684][ T7] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 5 [ 11.217152][ T23] sd 2:0:0:0: [sda] 7821312 512-byte logical blocks: (4.00 GB/3.73 GiB) [ 11.231896][ T23] sd 2:0:0:0: [sda] Write Protect is off [ 11.238126][ T23] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 11.267093][ T23] sda: sda1 [ 11.281885][ T23] sd 2:0:0:0: [sda] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: recovering journal rootfs: clean, 15073/244800 files, 166405/977403 blocks done. [ 20.888148][ T190] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.938954][ T190] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [ ok ] Synthesizing the initial hotplug events (devices)...done. [ 23.575036][ T372] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [....] Waiting for /dev to be fully populated...[ 23.808402][ T373] systemd-udevd[373]: Using default interface naming scheme 'v240'. [ 23.914522][ T373] systemd-udevd[373]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 24.077121][ T371] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 24.205176][ T371] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 24.253560][ T373] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 24.344507][ T405] marvell-cesa f1030000.crypto: CESA device successfully registered [ 24.353915][ T371] orion_wdt: Initial timeout 21 sec [ 24.435844][ T446] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. [ 24.513682][ T370] systemd-udevd[370]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'debian'...done. [ 24.970053][ C0] random: crng init done [ ok ] Activating swap:. [ 25.501281][ T594] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/52:3b:20:9c:11:51 Sending on LPF/eth0/52:3b:20:9c:11:51 Sending on Socket/fallback DHCPREQUEST for 192.168.0.15 on eth0 to 255.255.255.255 port 67 DHCPREQUEST for 192.168.0.15 on eth0 to 255.255.255.255 port 67 DHCPREQUEST for 192.168.0.15 on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 [ 28.215312][ T1118] mv643xx_eth: Set the PHY back to auto-negotiation mode [ 99.127599][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled No DHCPOFFERS received. Trying recorded lease 192.168.0.15 [ 108.294572][ T1124] NET: Registered protocol family 10 [ 108.301274][ T1124] Segment Routing with IPv6 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. --- 192.168.0.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1330 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1357 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login: