BootROM 1.08 Booting from NAND flash General initialization - Version: 1.0.0 High speed PHY - Version: 2.1.4 (COM-PHY-V20) Update PEX Device ID 0x6710 High speed PHY - Ended Successfully 0000 DDR3 Training Sequence - Ver 5.7.1 DDR3 Training Sequence - Run without PBS. DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:53:05) Marvell version: v2011.12 2014_T2.0p1 06/23/2015 ReadyNAS-102 V2.0 Board: DB-88F6710-BP SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB Map: Code: 0x1feef000:0x1ff9ef34 BSS: 0x1ffef0a0 Stack: 0x1f9eeef8 Heap: 0x1f9ef000:0x1feef000 NAND: (ID 0xf1ad) 128 MiB MMC: MRVL_MMC: 0 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x000001820000 nand_read_bbt: Bad block at 0x000001f00000 Initialize and scan all PCI interfaces PEX unit.port(active IF[-first bus]): ------------------------------------------ PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0 FPU not initialized USB 0: Host Mode USB 1: Host Mode Shutting down unused interfaces: GBE0 SDIO AUDIO TDM Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Net: , egiga1 [PRIME] Power On! FDT loaded successfully Hit any key to stop autoboot: 0 (Re)start USB... USB: Active port: 0 Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/boot/uImage" from usb device 0:1 (usbda1) 5417257 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 9488618 bytes read ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.8.5-mvebu-370xp-tld-1 Created: 2020-09-04 5:28:43 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5417193 Bytes = 5.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: initramfs-5.2.9-mvebu-tld-1 Created: 2019-08-26 11:03:27 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9488554 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.8.5-mvebu-370xp-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubun tu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Mon Aug 31 00:00:32 PDT 2020 [ 0.000000][ T0] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Globalscale Mirabox [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] HighMem empty [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] CPU: All CPU(s) started in SVC mode. [ 0.000000][ T0] percpu: Embedded 20 pages/cpu s53068 r8192 d20660 u81920 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:0x180000@0(u -boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) earlyprintk=serial mtdparts=px a3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) reason =normal bdtype=rn102 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 493628K/524288K available (10240K kernel code, 1012K rwdata, 3072K rodata, 1024K init, 342K bss, 306 60K reserved, 0K cma-reserved, 0K highmem) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x338/0x794 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x12086300 -> 0x1a086302 [ 0.000000][ T0] Aurora cache controller enabled, 4 ways, 256 kB [ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 [ 0.000000][ T0] Switching to timer-based delay loop, resolution 53ns [ 0.000007][ T0] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114537122277ns [ 0.007874][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101938038664 n s [ 0.019276][ T0] Console: colour dummy device 80x30 [ 0.023995][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 37.49 BogoMIPS (lpj=187492) [ 0.034125][ T0] pid_max: default: 32768 minimum: 301 [ 0.039216][ T0] LSM: Security Framework initializing [ 0.044151][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051479][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.060277][ T0] CPU: Testing write buffer coherency: ok [ 0.065717][ T1] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.072039][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.078723][ T1] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 [ 0.084150][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.090659][ T1] rcu: Hierarchical SRCU implementation. [ 0.098484][ T1] smp: Bringing up secondary CPUs ... [ 0.103374][ T1] smp: Brought up 1 node, 1 CPU [ 0.107671][ T1] SMP: Total of 1 processors activated (37.49 BogoMIPS). [ 0.113990][ T1] CPU: All CPU(s) started in SVC mode. [ 0.119523][ T1] devtmpfs: initialized [ 0.127698][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.136600][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.146368][ T1] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.153574][ T1] xor: measuring software checksum speed [ 0.258575][ T1] arm4regs : 1103.200 MB/sec [ 0.358571][ T1] 8regs : 671.200 MB/sec [ 0.458567][ T1] 32regs : 1062.400 MB/sec [ 0.463020][ T1] xor: using function: arm4regs (1103.200 MB/sec) [ 0.468784][ T1] prandom: seed boundary self test passed [ 0.477386][ T1] prandom: 100 self tests passed [ 0.481801][ T1] pinctrl core: initialized pinctrl subsystem [ 0.488921][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.489662][ T1] NET: Registered protocol family 16 [ 0.502501][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.510374][ T1] audit: initializing netlink subsys (disabled) [ 0.516337][ T31] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1 [ 0.526622][ T1] cpuidle: using governor ladder [ 0.532641][ T1] cpuidle: using governor menu [ 0.537130][ T1] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.809632][ T1] raid6: int32x8 gen() 214 MB/s [ 0.979026][ T1] raid6: int32x8 xor() 135 MB/s [ 1.148644][ T1] raid6: int32x4 gen() 224 MB/s [ 1.318714][ T1] raid6: int32x4 xor() 151 MB/s [ 1.488575][ T1] raid6: int32x2 gen() 414 MB/s [ 1.658568][ T1] raid6: int32x2 xor() 217 MB/s [ 1.828603][ T1] raid6: int32x1 gen() 430 MB/s [ 1.998590][ T1] raid6: int32x1 xor() 201 MB/s [ 2.003121][ T1] raid6: using algorithm int32x1 gen() 430 MB/s [ 2.008694][ T1] raid6: .... xor() 201 MB/s, rmw enabled [ 2.013778][ T1] raid6: using intx1 recovery algorithm [ 2.020120][ T1] vgaarb: loaded [ 2.025031][ T1] SCSI subsystem initialized [ 2.030297][ T1] usbcore: registered new interface driver usbfs [ 2.035995][ T1] usbcore: registered new interface driver hub [ 2.043180][ T1] usbcore: registered new device driver usb [ 2.049883][ T1] mc: Linux media interface: v0.10 [ 2.055287][ T1] videodev: Linux video capture interface: v2.00 [ 2.061787][ T1] pps_core: LinuxPPS API ver. 1 registered [ 2.066955][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.076699][ T1] PTP clock support registered [ 2.084515][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource [ 3.073596][ T1] VFS: Disk quotas dquot_6.6.0 [ 3.077982][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 3.115447][ T1] NET: Registered protocol family 2 [ 3.121459][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 3.130237][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 3.138205][ T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 3.145490][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 3.152498][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 3.159315][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 3.166544][ T1] NET: Registered protocol family 1 [ 3.171904][ T1] RPC: Registered named UNIX socket transport module. [ 3.178043][ T1] RPC: Registered udp transport module. [ 3.182971][ T1] RPC: Registered tcp transport module. [ 3.187918][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.194436][ T1] PCI: CLS 0 bytes, default 64 [ 3.199065][ T1] Trying to unpack rootfs image as initramfs... [ 3.812118][ T1] Freeing initrd memory: 9268K [ 3.816720][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 3.823614][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 3.835609][ T1] Initialise system trusted keyrings [ 3.840354][ T1] Key type blacklist registered [ 3.846157][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 3.852841][ T1] zbud: loaded [ 3.857623][ T1] NFS: Registering the id_resolver key type [ 3.862899][ T1] Key type id_resolver registered [ 3.867777][ T1] Key type id_legacy registered [ 3.872097][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.879018][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.885889][ T1] jffs2: version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc. [ 3.894041][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 3.901008][ T1] orangefs_init: module version upstream loaded [ 3.980756][ T1] async_tx: api initialized (async) [ 3.985474][ T1] Key type asymmetric registered [ 3.989848][ T1] Asymmetric key parser 'x509' registered [ 3.995197][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 4.002698][ T1] io scheduler bfq registered [ 4.009943][ T1] armada-370-pinctrl d0018000.pin-ctrl: registered pinctrl driver [ 4.026679][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 4.033446][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.039840][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 4.047136][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 4.053632][ T1] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 [ 4.059978][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 4.067382][ T1] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 [ 4.073530][ T1] pci 0000:00:02.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 4.081856][ T1] PCI: bus0: Fast back to back transfers disabled [ 4.087800][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.095886][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.104186][ T1] pci 0000:01:00.0: [1b4b:9170] type 00 class 0x010601 [ 4.110594][ T1] pci 0000:01:00.0: reg 0x10: [io 0xfffffff8-0xffffffff] [ 4.117073][ T1] pci 0000:01:00.0: reg 0x14: [io 0xfffffffc-0xffffffff] [ 4.123438][ T1] pci 0000:01:00.0: reg 0x18: [io 0xfffffff8-0xffffffff] [ 4.129893][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xfffffffc-0xffffffff] [ 4.136314][ T1] pci 0000:01:00.0: reg 0x20: [io 0xfffffff0-0xffffffff] [ 4.142678][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400001ff] [ 4.149103][ T1] pci 0000:01:00.0: reg 0x30: [mem 0xd0000000-0xd000ffff pref] [ 4.155925][ T1] pci 0000:01:00.0: Enabling fixed DMA alias to 00.1 [ 4.161942][ T1] pci 0000:01:00.0: PME# supported from D3hot [ 4.167851][ T1] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 4.205479][ T1] PCI: bus1: Fast back to back transfers disabled [ 4.211218][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 4.218326][ T1] pci 0000:02:00.0: [1b73:1009] type 00 class 0x0c0330 [ 4.224482][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x4200ffff 64bit] [ 4.231522][ T1] pci 0000:02:00.0: reg 0x18: [mem 0x42010000-0x42010fff 64bit] [ 4.238471][ T1] pci 0000:02:00.0: reg 0x20: [mem 0x42011000-0x42011fff 64bit] [ 4.245473][ T1] pci 0000:02:00.0: supports D1 [ 4.249772][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold [ 4.256727][ T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 4.295475][ T1] PCI: bus2: Fast back to back transfers disabled [ 4.301214][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 4.308049][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff] [ 4.315020][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff] [ 4.321933][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 4.328418][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref] [ 4.335671][ T1] pci 0000:00:02.0: BAR 6: assigned [mem 0xf8300000-0xf83007ff pref] [ 4.342908][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8000000-0xf800ffff pref] [ 4.350157][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xf8010000-0xf80101ff] [ 4.357013][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 4.363372][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 4.369749][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 4.376126][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 4.382486][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 4.388863][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 4.394032][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 4.400408][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 4.407267][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf810ffff 64bit] [ 4.414601][ T1] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8110000-0xf8110fff 64bit] [ 4.421916][ T1] pci 0000:02:00.0: BAR 4: assigned [mem 0xf8111000-0xf8111fff 64bit] [ 4.429247][ T1] pci 0000:00:02.0: PCI bridge to [bus 02] [ 4.434418][ T1] pci 0000:00:02.0: bridge window [mem 0xf8100000-0xf81fffff] [ 4.441389][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 4.447737][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0142) [ 4.455207][ T1] mv_xor d0060800.xor: Marvell shared XOR driver [ 4.525883][ T1] mv_xor d0060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.536895][ T1] mv_xor d0060900.xor: Marvell shared XOR driver [ 4.605893][ T1] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.808491][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 4.819810][ T1] printk: console [ttyS0] disabled [ 4.845819][ T1] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 20, base_baud = 12500000) is a 16550A [ 4.855002][ T1] printk: console [ttyS0] enabled [ 4.855002][ T1] printk: console [ttyS0] enabled [ 4.863988][ T1] printk: bootconsole [earlycon0] disabled [ 4.863988][ T1] printk: bootconsole [earlycon0] disabled [ 4.876833][ T1] ahci 0000:01:00.0: enabling device (0146 -> 0147) [ 4.883060][ T1] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode [ 4.892139][ T1] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 4.903624][ T1] scsi host0: ahci [ 4.908290][ T1] scsi host1: ahci [ 4.912299][ T1] ata1: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010100 irq 45 [ 4.920089][ T1] ata2: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010180 irq 45 [ 4.930548][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 4.937638][ T1] nand: Hynix H27U1G8F2BTR-BC [ 4.941821][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 4.949602][ T1] nand: WARNING: pxa3xx_nand-0: the ECC used on your system (1b/2048B) is too weak compared to the one require d by the NAND chip (1b/512B) [ 4.963143][ T1] Bad block table found at page 65472, version 0x01 [ 4.969645][ T1] Bad block table found at page 65408, version 0x01 [ 4.975885][ T1] nand_read_bbt: bad block at 0x000001820000 [ 4.981261][ T1] nand_read_bbt: bad block at 0x000001f00000 [ 4.986740][ T1] 5 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 4.993394][ T1] Creating 5 MTD partitions on "pxa3xx_nand-0": [ 4.999036][ T1] 0x000000000000-0x000000180000 : "u-boot" [ 5.006543][ T1] 0x000000180000-0x0000001a0000 : "u-boot-env" [ 5.014891][ T1] 0x000000200000-0x000000800000 : "uImage" [ 5.022845][ T1] 0x000000800000-0x000000c00000 : "minirootfs" [ 5.031211][ T1] 0x000000c00000-0x000008000000 : "ubifs" [ 5.040925][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.050099][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 5.063378][ T1] libphy: Fixed MDIO Bus: probed [ 5.072981][ T1] libphy: orion_mdio_bus: probed [ 5.092296][ T1] mdio_bus d0072004.mdio-mii: MDIO device at address 1 is missing.