U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:42:03 -0700) ZyXEL NSA325 2-Bay Power Media Server SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD30EFRX-68AX9N0 Firm: 80.00A80 Ser#: WD-WCC1T1087167 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N5AE5FKE Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 62666752 14effde5-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Partition Map for IDE device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 63 48321 7c3dec53-01 83 2 48384 4294918656 7c3dec53-02 83 Partition Map for IDE device 1 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 692 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4977686 bytes read in 983 ms (4.8 MiB/s) loading uInitrd ... 9713936 bytes read in 896 ms (10.3 MiB/s) loading DTB /boot/dts/kirkwood-nsa325.dtb ... 14006 bytes read in 1553 ms (8.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-11-18 8:44:06 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4977622 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 1f1ca000, end 1fb0d8d0 ... OK Loading Device Tree to 1f1c3000, end 1f1c96b5 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: ZyXEL NSA325 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000][ T0] Memory: 504168K/524288K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 20120K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000040][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000642][ T0] Console: colour dummy device 80x30 [ 0.000686][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000708][ T0] pid_max: default: 32768 minimum: 301 [ 0.001012][ T0] LSM: Security Framework initializing [ 0.001165][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001186][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001958][ T0] *** VALIDATE proc *** [ 0.002190][ T0] *** VALIDATE cgroup1 *** [ 0.002212][ T0] *** VALIDATE cgroup2 *** [ 0.002301][ T0] CPU: Testing write buffer coherency: ok [ 0.003752][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.004011][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.004256][ T1] rcu: Hierarchical SRCU implementation. [ 0.006794][ T1] devtmpfs: initialized [ 0.012020][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.012047][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.012273][ T1] xor: measuring software checksum speed [ 0.110100][ T1] arm4regs : 1453.200 MB/sec [ 0.210065][ T1] 8regs : 872.400 MB/sec [ 0.310062][ T1] 32regs : 1268.000 MB/sec [ 0.310078][ T1] xor: using function: arm4regs (1453.200 MB/sec) [ 0.310095][ T1] prandom: seed boundary self test passed [ 0.313228][ T1] prandom: 100 self tests passed [ 0.313237][ T1] pinctrl core: initialized pinctrl subsystem [ 0.314459][ T1] NET: Registered protocol family 16 [ 0.314791][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.315445][ T1] audit: initializing netlink subsys (disabled) [ 0.316490][ T14] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.316594][ T1] cpuidle: using governor ladder [ 0.316661][ T1] cpuidle: using governor menu [ 0.317026][ T1] Feroceon L2: Enabling L2 [ 0.317067][ T1] Feroceon L2: Cache support initialised. [ 0.321847][ T1] No ATAGs? [ 2.560046][ C0] random: fast init done [ 4.743448][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 4.743732][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 4.920386][ T1] raid6: int32x8 gen() 171 MB/s [ 5.090126][ T1] raid6: int32x8 xor() 115 MB/s [ 5.260182][ T1] raid6: int32x4 gen() 172 MB/s [ 5.430156][ T1] raid6: int32x4 xor() 112 MB/s [ 5.600132][ T1] raid6: int32x2 gen() 176 MB/s [ 5.770047][ T1] raid6: int32x2 xor() 125 MB/s [ 5.940333][ T1] raid6: int32x1 gen() 134 MB/s [ 6.110341][ T1] raid6: int32x1 xor() 92 MB/s [ 6.110350][ T1] raid6: using algorithm int32x2 gen() 176 MB/s [ 6.110356][ T1] raid6: .... xor() 125 MB/s, rmw enabled [ 6.110363][ T1] raid6: using intx1 recovery algorithm [ 6.110589][ T1] vgaarb: loaded [ 6.110990][ T1] SCSI subsystem initialized [ 6.111394][ T1] usbcore: registered new interface driver usbfs [ 6.111442][ T1] usbcore: registered new interface driver hub [ 6.111508][ T1] usbcore: registered new device driver usb [ 6.111643][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.111652][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 6.111672][ T1] PTP clock support registered [ 6.112657][ T1] clocksource: Switched to clocksource orion_clocksource [ 6.886580][ T1] VFS: Disk quotas dquot_6.6.0 [ 6.886664][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 6.894177][ T1] NET: Registered protocol family 2 [ 6.894843][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 6.894875][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 6.894929][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 6.894981][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 6.895057][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 6.895081][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 6.895266][ T1] NET: Registered protocol family 1 [ 6.895803][ T1] RPC: Registered named UNIX socket transport module. [ 6.895814][ T1] RPC: Registered udp transport module. [ 6.895820][ T1] RPC: Registered tcp transport module. [ 6.895827][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.895839][ T1] PCI: CLS 0 bytes, default 32 [ 6.896098][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 6.896992][ T1] Initialise system trusted keyrings [ 6.897036][ T1] Key type blacklist registered [ 6.897228][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 6.897299][ T1] zbud: loaded [ 6.898145][ T1] NFS: Registering the id_resolver key type [ 6.898170][ T1] Key type id_resolver registered [ 6.898178][ T1] Key type id_legacy registered [ 6.898193][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.898206][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.898440][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 6.898621][ T1] fuse: init (API version 7.31) [ 6.898933][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.899085][ T1] orangefs_init: module version upstream loaded [ 6.899096][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 6.901497][ T1] async_tx: api initialized (async) [ 6.901514][ T1] Key type asymmetric registered [ 6.901521][ T1] Asymmetric key parser 'x509' registered [ 6.901567][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 6.902784][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.904324][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 6.904342][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.904354][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.904364][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 6.904467][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 6.904501][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 6.905705][ T1] PCI: bus0: Fast back to back transfers disabled [ 6.905727][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.905879][ T1] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330 [ 6.905926][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 6.906075][ T1] pci 0000:01:00.0: PME# supported from D0 D3hot [ 6.906144][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 6.933743][ T1] PCI: bus1: Fast back to back transfers disabled [ 6.933765][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 6.933922][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 6.933937][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 6.933953][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] [ 6.933974][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.933988][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 6.934083][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 6.934150][ T1] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 6.934615][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.993276][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.994811][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 7.053279][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 7.055051][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 7.056095][ T1] printk: console [ttyS0] disabled [ 7.056158][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 7.948803][ T1] printk: console [ttyS0] enabled [ 7.959618][ T1] loop: module loaded [ 7.964000][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 7.971727][ T1] scsi host0: sata_mv [ 7.976091][ T1] scsi host1: sata_mv [ 7.980161][ T1] ata1: SATA max UDMA/133 irq 32 [ 7.985021][ T1] ata2: SATA max UDMA/133 irq 32 [ 7.990647][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 7.997829][ T1] nand: Samsung NAND 128MiB 3,3V 8-bit [ 8.003186][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 8.011491][ T1] Scanning device for bad blocks [ 8.037909][ T1] Bad eraseblock 226 at 0x000001c40000 [ 8.078051][ T1] Bad eraseblock 592 at 0x000004a00000 [ 8.091640][ T1] Bad eraseblock 678 at 0x0000054c0000 [ 8.129917][ T1] 9 fixed-partitions partitions found on MTD device orion_nand [ 8.137364][ T1] Creating 9 MTD partitions on "orion_nand": [ 8.143243][ T1] 0x000000000000-0x000000100000 : "uboot" [ 8.149889][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 8.156842][ T1] 0x000000180000-0x000000200000 : "key_store" [ 8.163789][ T1] 0x000000200000-0x000000280000 : "info" [ 8.170266][ T1] 0x000000280000-0x000000c80000 : "etc" [ 8.176726][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 8.183612][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 8.190468][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 8.197364][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 8.205189][ T1] libphy: Fixed MDIO Bus: probed [ 8.210624][ T1] libphy: orion_mdio_bus: probed [ 8.216570][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 8.224551][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 8.231896][ T1] mv643xx_eth: Set the PHY to fix link down [ 8.232596][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 8.248024][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.255367][ T1] ehci-pci: EHCI PCI platform driver [ 8.260594][ T1] ehci-orion: EHCI orion driver [ 8.265521][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 8.271782][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 8.280350][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 8.312675][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.319654][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 8.328747][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.336714][ T1] usb usb1: Product: EHCI Host Controller [ 8.342312][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 8.349669][ T1] usb usb1: SerialNumber: f1050000.ehci [ 8.355593][ T1] hub 1-0:1.0: USB hub found [ 8.360087][ T1] hub 1-0:1.0: 1 port detected [ 8.365408][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 8.371373][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 8.379824][ T1] xhci_hcd 0000:01:00.0: hcc params 0x014042c3 hci version 0x96 quirks 0x0000000000000004 [ 8.390048][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 8.399068][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.407039][ T1] usb usb2: Product: xHCI Host Controller [ 8.412639][ T1] usb usb2: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd [ 8.419995][ T1] usb usb2: SerialNumber: 0000:01:00.0 [ 8.425785][ T1] hub 2-0:1.0: USB hub found [ 8.430286][ T1] hub 2-0:1.0: 2 ports detected [ 8.435476][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 8.441438][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 8.449629][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 8.456732][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 8.465702][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02 [ 8.474801][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.482775][ T1] usb usb3: Product: xHCI Host Controller [ 8.488372][ T1] usb usb3: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd [ 8.495756][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 8.502775][ T1] usb usb3: SerialNumber: 0000:01:00.0 [ 8.508691][ T1] hub 3-0:1.0: USB hub found [ 8.513460][ T1] hub 3-0:1.0: 2 ports detected [ 8.518248][ T112] ata1.00: ATA-9: WDC WD30EFRX-68AX9N0, 80.00A80, max UDMA/133 [ 8.526311][ T1] usbcore: registered new interface driver usb-storage [ 8.533095][ T112] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.541041][ T1] mousedev: PS/2 mouse device common for all mice [ 8.547979][ T1] i2c /dev entries driver [ 8.554557][ T112] ata1.00: configured for UDMA/133 [ 8.563790][ T1] rtc-pcf8563 0-0051: registered as rtc0 [ 8.569985][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68A 0A80 PQ: 0 ANSI: 5 [ 8.580267][ T116] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 8.589406][ T1] device-mapper: uevent: version 1.0.3 [ 8.595041][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 8.604273][ T116] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 8.610294][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 8.616263][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.626118][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 8.633622][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 8.640962][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 8.649421][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 8.656274][ T1] device-mapper: raid: Loading target version 1.14.0 [ 8.662987][ T116] sda: sda1 sda2 [ 8.668414][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 8.675765][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.681376][ T1] drop_monitor: Initializing network drop monitor service [ 8.688685][ T1] NET: Registered protocol family 17 [ 8.694103][ T1] Key type dns_resolver registered [ 8.699671][ T1] registered taskstats version 1 [ 8.704540][ T1] Loading compiled-in X.509 certificates [ 8.710117][ T1] zswap: loaded using pool lzo/zbud [ 8.726607][ T1] Key type big_key registered [ 8.732733][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.741340][ T1] Key type encrypted registered [ 8.749096][ T1] rtc-pcf8563 0-0051: setting system clock to 2020-11-18T09:26:31 UTC (1605691591) [ 8.944108][ T15] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 8.953057][ T15] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.960934][ T15] usb 1-1: Product: USB2.0 Hub [ 8.966232][ T15] hub 1-1:1.0: USB hub found [ 8.970980][ T15] hub 1-1:1.0: 4 ports detected [ 9.092696][ T114] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.102140][ T114] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133 [ 9.109597][ T114] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 9.119653][ T114] ata2.00: configured for UDMA/133 [ 9.135081][ T23] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5 [ 9.144698][ T116] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 9.153490][ T116] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 9.159500][ T116] sd 1:0:0:0: [sdb] Write Protect is off [ 9.165131][ T116] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.186525][ T116] sdb: [ 9.190107][ T116] sd 1:0:0:0: [sdb] Attached SCSI disk [ 9.195639][ T1] md: Waiting for all devices to be available before autodetect [ 9.203273][ T1] md: If you don't use raid, use raid=noautodetect [ 9.210322][ T1] md: Autodetecting RAID arrays. [ 9.215192][ T1] md: autorun ... [ 9.218716][ T1] md: ... autorun DONE. [ 9.222937][ T1] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 9.231159][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 9.240322][ T1] 1f00 1024 mtdblock0 [ 9.240325][ T1] (driver?) [ 9.248394][ T1] 1f01 512 mtdblock1 [ 9.248397][ T1] (driver?) [ 9.256430][ T1] 1f02 512 mtdblock2 [ 9.256433][ T1] (driver?) [ 9.264446][ T1] 1f03 512 mtdblock3 [ 9.264449][ T1] (driver?) [ 9.272423][ T1] 1f04 10240 mtdblock4 [ 9.272426][ T1] (driver?) [ 9.280403][ T1] 1f05 10240 mtdblock5 [ 9.280405][ T1] (driver?) [ 9.288382][ T1] 1f06 48896 mtdblock6 [ 9.288384][ T1] (driver?) [ 9.296360][ T1] 1f07 10240 mtdblock7 [ 9.296362][ T1] (driver?) [ 9.304344][ T1] 1f08 48896 mtdblock8 [ 9.304346][ T1] (driver?) [ 9.312308][ T1] 0800 2930266584 sda [ 9.312311][ T1] driver: sd [ 9.319851][ T1] 0801 24160 sda1 7c3dec53-01 [ 9.319853][ T1] [ 9.327665][ T15] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 9.335289][ T1] 0802 2147459328 sda2 7c3dec53-02 [ 9.335292][ T1] [ 9.343124][ T1] 0810 2930266584 sdb [ 9.343127][ T1] driver: sd [ 9.350691][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 9.359693][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.9-kirkwood-tld-1 #1 [ 9.367379][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 9.374388][ T1] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 9.382871][ T1] [] (show_stack) from [] (panic+0xe0/0x30c) [ 9.390484][ T1] [] (panic) from [] (mount_block_root+0x1bc/0x2a4) [ 9.398701][ T1] [] (mount_block_root) from [] (mount_root+0xe8/0x154) [ 9.407263][ T1] [] (mount_root) from [] (prepare_namespace+0x14c/0x18c) [ 9.416000][ T1] [] (prepare_namespace) from [] (kernel_init_freeable+0x270/0x2dc) [ 9.425613][ T1] [] (kernel_init_freeable) from [] (kernel_init+0x8/0x10c) [ 9.434531][ T1] [] (kernel_init) from [] (ret_from_fork+0x14/0x34) [ 9.442826][ T1] Exception stack(0xdf48bfb0 to 0xdf48bff8) [ 9.448592][ T1] bfa0: 00000000 00000000 00000000 00000000 [ 9.457504][ T1] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 9.466416][ T1] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 9.473766][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---