U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:42:03 -0700) ZyXEL NSA325 2-Bay Power Media Server SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD30EFRX-68AX9N0 Firm: 80.00A80 Ser#: WD-WCC1T1087167 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N5AE5FKE Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 62666752 14effde5-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Partition Map for IDE device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x15d509baf "raiddata0" attrs: 0x0000000000000000 type: e6d6d379-f507-44c2-a23c-238f2a3df928 type: lvm guid: 41771c29-bf19-452a-a7d6-99376599f225 Partition Map for IDE device 1 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x15d509baf "raddata1" attrs: 0x0000000000000000 type: e6d6d379-f507-44c2-a23c-238f2a3df928 type: lvm guid: 155fb2e3-4631-44c9-ad55-1dc3be14f036 Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 691 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4963680 bytes read in 857 ms (5.5 MiB/s) loading uInitrd ... 9713936 bytes read in 771 ms (12 MiB/s) loading DTB /boot/dts/kirkwood-nsa325.dtb ... 14006 bytes read in 1553 ms (8.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4963616 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 1f1ca000, end 1fb0d8d0 ... OK Loading Device Tree to 1f1c3000, end 1f1c96b5 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: ZyXEL NSA325 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000][ T0] Memory: 494676K/524288K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 29612K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000040][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000648][ T0] Console: colour dummy device 80x30 [ 0.000693][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000716][ T0] pid_max: default: 32768 minimum: 301 [ 0.001020][ T0] LSM: Security Framework initializing [ 0.001172][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001193][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001890][ T0] *** VALIDATE proc *** [ 0.002111][ T0] *** VALIDATE cgroup1 *** [ 0.002132][ T0] *** VALIDATE cgroup2 *** [ 0.002215][ T0] CPU: Testing write buffer coherency: ok [ 0.003675][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.003934][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.004174][ T1] rcu: Hierarchical SRCU implementation. [ 0.006802][ T1] devtmpfs: initialized [ 0.012223][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.012250][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.012468][ T1] xor: measuring software checksum speed [ 0.110096][ T1] arm4regs : 1452.000 MB/sec [ 0.210059][ T1] 8regs : 872.400 MB/sec [ 0.310063][ T1] 32regs : 1268.400 MB/sec [ 0.310080][ T1] xor: using function: arm4regs (1452.000 MB/sec) [ 0.310097][ T1] prandom: seed boundary self test passed [ 0.313230][ T1] prandom: 100 self tests passed [ 0.313238][ T1] pinctrl core: initialized pinctrl subsystem [ 0.314471][ T1] NET: Registered protocol family 16 [ 0.314884][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.315531][ T1] audit: initializing netlink subsys (disabled) [ 0.316571][ T14] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.316674][ T1] cpuidle: using governor ladder [ 0.316739][ T1] cpuidle: using governor menu [ 0.317189][ T1] Feroceon L2: Enabling L2 [ 0.317230][ T1] Feroceon L2: Cache support initialised. [ 0.322027][ T1] No ATAGs? [ 2.560045][ C0] random: fast init done [ 4.743591][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 4.743873][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 4.920458][ T1] raid6: int32x8 gen() 171 MB/s [ 5.090147][ T1] raid6: int32x8 xor() 115 MB/s [ 5.260121][ T1] raid6: int32x4 gen() 173 MB/s [ 5.430153][ T1] raid6: int32x4 xor() 112 MB/s [ 5.600332][ T1] raid6: int32x2 gen() 177 MB/s [ 5.770046][ T1] raid6: int32x2 xor() 125 MB/s [ 5.940333][ T1] raid6: int32x1 gen() 134 MB/s [ 6.110339][ T1] raid6: int32x1 xor() 92 MB/s [ 6.110347][ T1] raid6: using algorithm int32x2 gen() 177 MB/s [ 6.110354][ T1] raid6: .... xor() 125 MB/s, rmw enabled [ 6.110360][ T1] raid6: using intx1 recovery algorithm [ 6.110583][ T1] vgaarb: loaded [ 6.110992][ T1] SCSI subsystem initialized [ 6.111399][ T1] usbcore: registered new interface driver usbfs [ 6.111448][ T1] usbcore: registered new interface driver hub [ 6.111514][ T1] usbcore: registered new device driver usb [ 6.111661][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.111670][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 6.111691][ T1] PTP clock support registered [ 6.112740][ T1] clocksource: Switched to clocksource orion_clocksource [ 6.886662][ T1] VFS: Disk quotas dquot_6.6.0 [ 6.886747][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 6.894290][ T1] NET: Registered protocol family 2 [ 6.894954][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 6.894986][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 6.895039][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 6.895091][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 6.895166][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 6.895189][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 6.895376][ T1] NET: Registered protocol family 1 [ 6.895908][ T1] RPC: Registered named UNIX socket transport module. [ 6.895919][ T1] RPC: Registered udp transport module. [ 6.895926][ T1] RPC: Registered tcp transport module. [ 6.895932][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.895944][ T1] PCI: CLS 0 bytes, default 32 [ 6.896142][ T1] Trying to unpack rootfs image as initramfs... [ 7.540056][ T1] Freeing initrd memory: 9488K [ 7.540206][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 7.541241][ T1] Initialise system trusted keyrings [ 7.541285][ T1] Key type blacklist registered [ 7.541479][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 7.541567][ T1] zbud: loaded [ 7.542453][ T1] NFS: Registering the id_resolver key type [ 7.542483][ T1] Key type id_resolver registered [ 7.542490][ T1] Key type id_legacy registered [ 7.542506][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 7.542521][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.542819][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 7.543011][ T1] fuse: init (API version 7.31) [ 7.543356][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 7.543506][ T1] orangefs_init: module version upstream loaded [ 7.543516][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 7.556977][ T1] async_tx: api initialized (async) [ 7.556998][ T1] Key type asymmetric registered [ 7.557005][ T1] Asymmetric key parser 'x509' registered [ 7.557068][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 7.558240][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 7.559765][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 7.559785][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 7.559797][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 7.559808][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 7.559911][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 7.559944][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 7.561147][ T1] PCI: bus0: Fast back to back transfers disabled [ 7.561169][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 7.561332][ T1] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330 [ 7.561379][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 7.561521][ T1] pci 0000:01:00.0: PME# supported from D0 D3hot [ 7.561588][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 7.583845][ T1] PCI: bus1: Fast back to back transfers disabled [ 7.583867][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 7.584025][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 7.584040][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 7.584056][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] [ 7.584077][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 7.584092][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 7.584184][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 7.584250][ T1] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 7.584714][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 7.643397][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 7.644937][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 7.703356][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 7.705130][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 7.706181][ T1] printk: console [ttyS0] disabled [ 7.706244][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 8.617740][ T1] printk: console [ttyS0] enabled [ 8.628551][ T1] loop: module loaded [ 8.632938][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 8.640663][ T1] scsi host0: sata_mv [ 8.645007][ T1] scsi host1: sata_mv [ 8.649095][ T1] ata1: SATA max UDMA/133 irq 32 [ 8.653956][ T1] ata2: SATA max UDMA/133 irq 32 [ 8.659592][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 8.666773][ T1] nand: Samsung NAND 128MiB 3,3V 8-bit [ 8.672111][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 8.680438][ T1] Scanning device for bad blocks [ 8.706851][ T1] Bad eraseblock 226 at 0x000001c40000 [ 8.746992][ T1] Bad eraseblock 592 at 0x000004a00000 [ 8.760468][ T1] Bad eraseblock 678 at 0x0000054c0000 [ 8.798672][ T1] 4 cmdlinepart partitions found on MTD device orion_nand [ 8.805679][ T1] Creating 4 MTD partitions on "orion_nand": [ 8.811537][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 8.818280][ T1] 0x000000100000-0x000000500000 : "uImage" [ 8.824982][ T1] 0x000000500000-0x000002500000 : "rootfs" [ 8.831689][ T1] 0x000002500000-0x000008000000 : "data" [ 8.839359][ T1] libphy: Fixed MDIO Bus: probed [ 8.844843][ T1] libphy: orion_mdio_bus: probed [ 8.861131][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 8.869124][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 8.876520][ T1] mv643xx_eth: Set the PHY to fix link down [ 8.877217][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:00:02:02 [ 8.892654][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.899985][ T1] ehci-pci: EHCI PCI platform driver [ 8.905236][ T1] ehci-orion: EHCI orion driver [ 8.910120][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 8.916421][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 8.924970][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 8.952759][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.959730][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 8.968768][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.976748][ T1] usb usb1: Product: EHCI Host Controller [ 8.982362][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 8.989731][ T1] usb usb1: SerialNumber: f1050000.ehci [ 8.995702][ T1] hub 1-0:1.0: USB hub found [ 9.000195][ T1] hub 1-0:1.0: 1 port detected [ 9.005501][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 9.011464][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 9.019919][ T1] xhci_hcd 0000:01:00.0: hcc params 0x014042c3 hci version 0x96 quirks 0x0000000000000004 [ 9.030150][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 9.039177][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.047146][ T1] usb usb2: Product: xHCI Host Controller [ 9.052761][ T1] usb usb2: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd [ 9.060097][ T1] usb usb2: SerialNumber: 0000:01:00.0 [ 9.065888][ T1] hub 2-0:1.0: USB hub found [ 9.070386][ T1] hub 2-0:1.0: 2 ports detected [ 9.075571][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 9.081531][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 9.089714][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 9.096813][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 9.105767][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02 [ 9.114865][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.122931][ T1] usb usb3: Product: xHCI Host Controller [ 9.128533][ T1] usb usb3: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd [ 9.135895][ T1] usb usb3: SerialNumber: 0000:01:00.0 [ 9.141680][ T1] hub 3-0:1.0: USB hub found [ 9.146226][ T1] hub 3-0:1.0: 2 ports detected [ 9.151562][ T1] usbcore: registered new interface driver usb-storage [ 9.158635][ T1] mousedev: PS/2 mouse device common for all mice [ 9.164988][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.172469][ T1] i2c /dev entries driver [ 9.177004][ T112] ata1.00: ATA-9: WDC WD30EFRX-68AX9N0, 80.00A80, max UDMA/133 [ 9.185290][ T112] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 9.195393][ T112] ata1.00: configured for UDMA/133 [ 9.203526][ T1] rtc-pcf8563 0-0051: registered as rtc0 [ 9.210830][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68A 0A80 PQ: 0 ANSI: 5 [ 9.219744][ T1] device-mapper: uevent: version 1.0.3 [ 9.225468][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 9.235454][ T116] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 9.244334][ T116] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 9.250629][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 9.258236][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 9.263790][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 9.271130][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 9.278610][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.289524][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 9.296386][ T1] device-mapper: raid: Loading target version 1.14.0 [ 9.305493][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 9.311892][ T1] drop_monitor: Initializing network drop monitor service [ 9.319164][ T1] NET: Registered protocol family 17 [ 9.324567][ T1] Key type dns_resolver registered [ 9.330191][ T1] registered taskstats version 1 [ 9.335034][ T1] Loading compiled-in X.509 certificates [ 9.340606][ T1] zswap: loaded using pool lzo/zbud [ 9.353431][ T116] sda: sda1 [ 9.361881][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 9.372846][ T119] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 9.437229][ T1] Key type big_key registered [ 9.475342][ T1] Key type encrypted registered [ 9.483003][ T1] rtc-pcf8563 0-0051: setting system clock to 2020-11-19T01:28:59 UTC (1605749339) [ 9.584227][ T119] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 9.593176][ T119] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 9.601061][ T119] usb 1-1: Product: USB2.0 Hub [ 9.606356][ T119] hub 1-1:1.0: USB hub found [ 9.611098][ T119] hub 1-1:1.0: 4 ports detected [ 9.742781][ T114] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.752220][ T114] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133 [ 9.759676][ T114] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 9.771818][ T114] ata2.00: configured for UDMA/133 [ 9.787238][ T23] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5 [ 9.796845][ T7] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 9.805630][ T7] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 9.811642][ T7] sd 1:0:0:0: [sdb] Write Protect is off [ 9.817273][ T7] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.878901][ T7] sdb: sdb1 [ 9.883259][ T7] sd 1:0:0:0: [sdb] Attached SCSI disk [ 9.891607][ T1] Freeing unused kernel memory: 1024K [ 9.903249][ T1] Checked W+X mappings: passed, no W+X pages found [ 9.909634][ T1] Run /init as init process [ 9.932981][ T119] usb 1-1.3: new high-speed USB device number 3 using orion-ehci Loading, please wait... Starting version 241 [ 10.098493][ T119] usb 1-1.3: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00 [ 10.119514][ T119] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.152862][ T119] usb 1-1.3: Product: Flash Drive FIT [ 10.158121][ T119] usb 1-1.3: Manufacturer: Samsung [ 10.171789][ T119] usb 1-1.3: SerialNumber: 0339618020001524 [ 10.196699][ T119] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 10.224121][ T119] scsi host2: usb-storage 1-1.3:1.0 [ 10.565969][ T161] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. [ 11.498312][ T23] scsi 2:0:0:0: Direct-Access Samsung Flash Drive FIT 1100 PQ: 0 ANSI: 6 [ 11.512158][ T7] sd 2:0:0:0: [sdc] 62668800 512-byte logical blocks: (32.1 GB/29.9 GiB) [ 11.526018][ T7] sd 2:0:0:0: [sdc] Write Protect is off [ 11.532373][ T7] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.549967][ T7] sdc: sdc1 [ 11.565132][ T7] sd 2:0:0:0: [sdc] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 fsck: error 2 (No such file or directory) while executing fsck.ext4 for /dev/sdc1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 26.339775][ T194] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [ ok ] Synthesizing the initial hotplug events (devices)...[ 28.782259][ C0] random: crng init done done. [ 28.804417][ T393] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [....] Waiting for /dev to be fully populated...[ 28.880165][ T374] systemd-udevd[374]: Using default interface naming scheme 'v240'. [ 29.021965][ T374] systemd-udevd[374]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 29.146439][ T392] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 29.286780][ T392] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 29.401380][ T392] orion_wdt: Initial timeout 21 sec [ 29.431216][ T407] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 29.465822][ T376] marvell-cesa f1030000.crypto: CESA device successfully registered [ 29.493889][ T407] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 29.546209][ T407] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 29.785939][ T393] systemd-udevd[393]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 30.829628][ T595] EXT4-fs (sdc1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.33.1 . ok [ 31.009013][ T620] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location [ ok itable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:00:02:02 Sending on LPF/eth0/00:50:43:00:02:02 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 [ 33.736278][ T1145] mv643xx_eth: Set the PHY back to auto-negotiation mode [ 36.794094][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPOFFER of 192.168.1.77 from 192.168.1.1 DHCPREQUEST for 192.168.1.77 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.77 from 192.168.1.1 bound to 192.168.1.77 -- renewal in 34598 seconds. [ 43.819207][ T1176] NET: Registered protocol family 10 [ 43.826012][ T1176] Segment Routing with IPv6 done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1370 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1397 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login: