__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000' Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... ....................................................................... 4975179 bytes read .... . ................... ......................... ................................................... ................................................................................................................................................................................................................................................................................................................... .... .................................................................................................................................................................................................................................................................................................................................................................................................................... .... ............................................................................................................................ 9713936 bytes read ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-12-17 11:52:39 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4975115 Bytes = 4.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005317f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000][ T0] Memory: 234784K/262144K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 27360K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008521][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015869][ T0] Console: colour dummy device 80x30 [ 0.021064][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032277][ T0] pid_max: default: 32768 minimum: 301 [ 0.037936][ T0] LSM: Security Framework initializing [ 0.043442][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.050775][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.059394][ T0] *** VALIDATE proc *** [ 0.063632][ T0] *** VALIDATE cgroup1 *** [ 0.067895][ T0] *** VALIDATE cgroup2 *** [ 0.072275][ T0] CPU: Testing write buffer coherency: ok [ 0.079521][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.086653][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.092785][ T1] rcu: Hierarchical SRCU implementation. [ 0.101931][ T1] devtmpfs: initialized [ 0.111653][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.122216][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.129287][ T1] xor: measuring software checksum speed [ 0.228543][ T1] arm4regs : 1013.200 MB/sec [ 0.328544][ T1] 8regs : 646.400 MB/sec [ 0.428543][ T1] 32regs : 939.600 MB/sec [ 0.433408][ T1] xor: using function: arm4regs (1013.200 MB/sec) [ 0.439692][ T1] prandom: seed boundary self test passed [ 0.449736][ T1] prandom: 100 self tests passed [ 0.454513][ T1] pinctrl core: initialized pinctrl subsystem [ 0.461879][ T1] NET: Registered protocol family 16 [ 0.467561][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.475972][ T1] audit: initializing netlink subsys (disabled) [ 0.483283][ T14] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1 [ 0.491825][ T1] cpuidle: using governor ladder [ 0.496672][ T1] cpuidle: using governor menu [ 0.501868][ T1] Feroceon L2: Enabling L2 [ 0.506155][ T1] Feroceon L2: Cache support initialised. [ 0.518014][ T1] No ATAGs? [ 2.568528][ C0] random: fast init done [ 6.620643][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 6.626818][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 6.809041][ T1] raid6: int32x8 gen() 123 MB/s [ 6.978979][ T1] raid6: int32x8 xor() 84 MB/s [ 7.149008][ T1] raid6: int32x4 gen() 126 MB/s [ 7.318781][ T1] raid6: int32x4 xor() 81 MB/s [ 7.488842][ T1] raid6: int32x2 gen() 127 MB/s [ 7.658874][ T1] raid6: int32x2 xor() 89 MB/s [ 7.828694][ T1] raid6: int32x1 gen() 99 MB/s [ 7.998968][ T1] raid6: int32x1 xor() 64 MB/s [ 8.003909][ T1] raid6: using algorithm int32x2 gen() 127 MB/s [ 8.009993][ T1] raid6: .... xor() 89 MB/s, rmw enabled [ 8.015451][ T1] raid6: using intx1 recovery algorithm [ 8.021098][ T1] vgaarb: loaded [ 8.025022][ T1] SCSI subsystem initialized [ 8.029986][ T1] usbcore: registered new interface driver usbfs [ 8.036190][ T1] usbcore: registered new interface driver hub [ 8.042302][ T1] usbcore: registered new device driver usb [ 8.048203][ T1] pps_core: LinuxPPS API ver. 1 registered [ 8.053863][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 8.063684][ T1] PTP clock support registered [ 8.069674][ T1] clocksource: Switched to clocksource orion_clocksource [ 9.234462][ T1] VFS: Disk quotas dquot_6.6.0 [ 9.239143][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 9.257069][ T1] NET: Registered protocol family 2 [ 9.263018][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 9.271434][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 9.279085][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 9.286187][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 9.293344][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 9.299883][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 9.307045][ T1] NET: Registered protocol family 1 [ 9.312755][ T1] RPC: Registered named UNIX socket transport module. [ 9.319341][ T1] RPC: Registered udp transport module. [ 9.324796][ T1] RPC: Registered tcp transport module. [ 9.330190][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.337300][ T1] PCI: CLS 0 bytes, default 32 [ 9.342157][ T1] Trying to unpack rootfs image as initramfs... [ 10.206988][ T1] Freeing initrd memory: 9488K [ 10.211871][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 10.220433][ T1] Initialise system trusted keyrings [ 10.225587][ T1] Key type blacklist registered [ 10.230553][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.237761][ T1] zbud: loaded [ 10.242204][ T1] NFS: Registering the id_resolver key type [ 10.247940][ T1] Key type id_resolver registered [ 10.252882][ T1] Key type id_legacy registered [ 10.257581][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 10.264968][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.272303][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 10.280274][ T1] fuse: init (API version 7.31) [ 10.285379][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.292699][ T1] orangefs_init: module version upstream loaded [ 10.298763][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 10.324837][ T1] async_tx: api initialized (async) [ 10.329980][ T1] Key type asymmetric registered [ 10.334748][ T1] Asymmetric key parser 'x509' registered [ 10.340429][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 10.350122][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.360228][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 10.368463][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.374687][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 10.382255][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 10.389287][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 10.396010][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 10.404903][ T1] PCI: bus0: Fast back to back transfers disabled [ 10.411192][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 10.421304][ T1] PCI: bus1: Fast back to back transfers enabled [ 10.427471][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 10.434974][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 10.442886][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.449169][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.510569][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.520751][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.580550][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.591030][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.599423][ T1] printk: console [ttyS0] disabled [ 10.604506][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 10.614210][ T1] printk: console [ttyS0] enabled [ 10.614210][ T1] printk: console [ttyS0] enabled [ 10.624053][ T1] printk: bootconsole [earlycon0] disabled [ 10.624053][ T1] printk: bootconsole [earlycon0] disabled [ 10.643533][ T1] loop: module loaded [ 10.648018][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 10.656576][ T1] scsi host0: sata_mv [ 10.661112][ T1] scsi host1: sata_mv [ 10.665281][ T1] ata1: SATA max UDMA/133 irq 33 [ 10.670160][ T1] ata2: SATA max UDMA/133 irq 33 [ 10.675996][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 10.683203][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit [ 10.688542][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 10.696877][ T1] Scanning device for bad blocks [ 10.906765][ T1] Bad eraseblock 1920 at 0x00000f000000 [ 10.925823][ T1] 3 fixed-partitions partitions found on MTD device orion_nand [ 10.933302][ T1] Creating 3 MTD partitions on "orion_nand": [ 10.939194][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 10.946332][ T1] 0x000000100000-0x000000700000 : "uImage" [ 10.953416][ T1] 0x000000700000-0x000010000000 : "root" [ 10.962516][ T1] libphy: Fixed MDIO Bus: probed [ 10.968218][ T1] libphy: orion_mdio_bus: probed [ 10.973132][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove [ 10.999050][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 11.007187][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 11.014097][ T112] ata1: SATA link down (SStatus 0 SControl F300) [ 11.361398][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 11.740363][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:01:d2:0e:0a:72 [ 11.749992][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.757271][ T1] ehci-pci: EHCI PCI platform driver [ 11.762522][ T1] ehci-orion: EHCI orion driver [ 11.767450][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.773735][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.782339][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.809715][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.816723][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 11.825757][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.833736][ T1] usb usb1: Product: EHCI Host Controller [ 11.839338][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 11.846702][ T1] usb usb1: SerialNumber: f1050000.ehci [ 11.852782][ T1] hub 1-0:1.0: USB hub found [ 11.857289][ T1] hub 1-0:1.0: 1 port detected [ 11.862707][ T1] usbcore: registered new interface driver usb-storage [ 11.869881][ T1] mousedev: PS/2 mouse device common for all mice [ 11.876761][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 11.882582][ T1] i2c /dev entries driver [ 12.229713][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.430473][ T15] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11 [ 12.439404][ T15] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.447305][ T15] usb 1-1: Product: USB 2.0 Hub [ 12.452636][ T15] hub 1-1:1.0: USB hub found [ 12.457222][ T15] hub 1-1:1.0: 4 ports detected [ 12.879705][ T15] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 13.130849][ T15] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00 [ 13.139977][ T15] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 13.148042][ T15] usb 1-1.2: Product: Cruzer Fit [ 13.152880][ T15] usb 1-1.2: Manufacturer: SanDisk' [ 13.157959][ T15] usb 1-1.2: SerialNumber: 00005103080620233952 [ 13.164914][ T15] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 13.172403][ T15] scsi host2: usb-storage 1-1.2:1.0 [ 13.929715][ T1] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0 [ 13.936984][ T1] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-110 addr=0e, data=03 [ 13.945400][ T1] rtc-pcf8563 0-0051: pcf8563_probe: write error [ 13.951675][ T1] rtc-pcf8563: probe of 0-0051 failed with error -5 [ 13.959030][ T1] device-mapper: uevent: version 1.0.3 [ 13.964718][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 13.974363][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 13.981696][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 13.989043][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 13.996498][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 14.003349][ T1] device-mapper: raid: Loading target version 1.14.0 [ 14.011754][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 14.018222][ T1] drop_monitor: Initializing network drop monitor service [ 14.025611][ T1] NET: Registered protocol family 17 [ 14.031051][ T1] Key type dns_resolver registered [ 14.036921][ T1] registered taskstats version 1 [ 14.041772][ T1] Loading compiled-in X.509 certificates [ 14.047360][ T1] zswap: loaded using pool lzo/zbud [ 14.145279][ T1] Key type big_key registered [ 14.192212][ T1] Key type encrypted registered [ 14.199086][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-12-18T12:22:35 UTC (1608294155) [ 14.211837][ T1] Freeing unused kernel memory: 1024K [ 14.220368][ T1] Checked W+X mappings: passed, no W+X pages found [ 14.226758][ T1] Run /init as init process [ 14.251218][ T23] scsi 2:0:0:0: Direct-Access SanDisk' Cruzer Fit 1.00 PQ: 0 ANSI: 6 [ 14.266788][ T7] sd 2:0:0:0: [sda] 60088320 512-byte logical blocks: (30.8 GB/28.7 GiB) [ 14.281783][ T7] sd 2:0:0:0: [sda] Write Protect is off [ 14.291921][ T7] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA Loading, please wait... [ 14.314425][ T7] sda: sda1 [ 14.322907][ T7] sd 2:0:0:0: [sda] Attached SCSI removable disk Starting version 241 [ 15.238715][ T165] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: recovering journal rootfs: clean, 15079/1880480 files, 350575/7510528 blocks done. [ 26.062780][ T192] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 26.136371][ T192] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [ ok ] Synthesizing the initial hotplug events (devices)...[ 29.072545][ T394] input: gpio-keys as /devices/platform/gpio-keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 29.132716][ T392] systemd-udevd[392]: Using default interface naming scheme 'v240'. [ 29.289040][ T392] systemd-udevd[392]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 29.427380][ C0] random: crng init done [ 29.587540][ T372] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 29.700891][ T372] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 29.848949][ T374] marvell-cesa f1030000.crypto: CESA device successfully registered [ 29.875324][ T372] orion_wdt: Initial timeout 21 sec [ 29.928172][ T391] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 30.034073][ T393] systemd-udevd[393]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.689727][ T394] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0 [ 31.697113][ T394] lm75: probe of 0-0048 failed with error -110 done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 32.582661][ T590] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:01:d2:0e:0a:72 Sending on LPF/eth0/00:01:d2:0e:0a:72 Sending on Socket/fallback DHCPREQUEST for 192.168.0.85 on eth0 to 255.255.255.255 port 67 [ 38.256397][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled DHCPREQUEST for 192.168.0.85 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.0.85 from 192.168.0.254 invoke-rc.d: could not determine current runlevel bound to 192.168.0.85 -- renewal in 476809 seconds. [ 44.048119][ T1151] NET: Registered protocol family 10 [ 44.055342][ T1151] Segment Routing with IPv6 done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1360 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1387 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Fri Dec 18 03:46:27 PST 2020 on ttyS0 Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# printenv SHELL=/bin/bash PWD=/root LOGNAME=root HOME=/root LANG=C TERM=linux USER=root SHLVL=1 HUSHLOGIN=FALSE PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin MAIL=/var/mail/root _=/usr/bin/printenv root@debian:~# usb reset -bash: usb: command not found root@debian:~# help GNU bash, version 5.0.3(1)-release (arm-unknown-linux-gnueabi) These shell commands are defined internally. Type `help' to see this list. Type `help name' to find out more about the function `name'. Use `info bash' to find out more about the shell in general. Use `man -k' or `info' to find out more about commands not in this list. A star (*) next to a name means that the command is disabled. job_spec [&] history [-c] [-d offset] [n] or hist> (( expression )) if COMMANDS; then COMMANDS; [ elif C> . filename [arguments] jobs [-lnprs] [jobspec ...] or jobs > : kill [-s sigspec | -n signum | -sigs> [ arg... ] let arg [arg ...] [[ expression ]] local [option] name[=value] ... alias [-p] [name[=value] ... ] logout [n] bg [job_spec ...] mapfile [-d delim] [-n count] [-O or> bind [-lpsvPSVX] [-m keymap] [-f file> popd [-n] [+N | -N] break [n] printf [-v var] format [arguments] builtin [shell-builtin [arg ...]] pushd [-n] [+N | -N | dir] caller [expr] pwd [-LP] case WORD in [PATTERN [| PATTERN]...)> read [-ers] [-a array] [-d delim] [-> cd [-L|[-P [-e]] [-@]] [dir] readarray [-d delim] [-n count] [-O > command [-pVv] command [arg ...] readonly [-aAf] [name[=value] ...] o> compgen [-abcdefgjksuv] [-o option] [> return [n] complete [-abcdefgjksuv] [-pr] [-DEI]> select NAME [in WORDS ... ;] do COMM> compopt [-o|+o option] [-DEI] [name .> set [-abefhkmnptuvxBCHP] [-o option-> continue [n] shift [n] coproc [NAME] command [redirections] shopt [-pqsu] [-o] [optname ...] declare [-aAfFgilnrtux] [-p] [name[=v> source filename [arguments] dirs [-clpv] [+N] [-N] suspend [-f] disown [-h] [-ar] [jobspec ... | pid > test [expr] echo [-neE] [arg ...] time [-p] pipeline enable [-a] [-dnps] [-f filename] [na> times eval [arg ...] trap [-lp] [[arg] signal_spec ...] exec [-cl] [-a name] [command [argume> true exit [n] type [-afptP] name [name ...] export [-fn] [name[=value] ...] or ex> typeset [-aAfFgilnrtux] [-p] name[=v> false ulimit [-SHabcdefiklmnpqrstuvxPT] [l> fc [-e ename] [-lnr] [first] [last] o> umask [-p] [-S] [mode] fg [job_spec] unalias [-a] name [name ...] for NAME [in WORDS ... ] ; do COMMAND> unset [-f] [-v] [-n] [name ...] for (( exp1; exp2; exp3 )); do COMMAN> until COMMANDS; do COMMANDS; done function name { COMMANDS ; } or name > variables - Names and meanings of so> getopts optstring name [arg] wait [-fn] [id ...] hash [-lr] [-p pathname] [-dt] [name > while COMMANDS; do COMMANDS; done help [-dms] [pattern ...] { COMMANDS ; } root@debian:~#