Marvell>> BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48206 (Dec 03 2015 - 02:50:37) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95e28 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 2 @0x08700000 *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: Marvell>> run usb_bootcmd Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found 5237717 bytes read in 414 ms (12.1 MiB/s) 19485 bytes read in 657 ms (28.3 KiB/s) 9779082 bytes read in 416 ms (22.4 MiB/s) * kernel: cmdline image address = 0x02000000 ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-5.13.8-mvebu-tld-1 Created: 2021-08-28 12:14:45 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9779018 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Ramdisk to 1f07b000, end 1f9ce74a ... OK Loading Device Tree to 00ff8000, end 00fffc1c ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 [ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NAS326 [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] HighMem empty [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 501396K/524288K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 22892K reserved, 0K cma-reserved, 0K highmem) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000001][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns [ 0.000024][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns [ 0.000047][ T0] Switching to timer-based delay loop, resolution 1ns [ 0.000280][ T0] Ignoring duplicate/late registration of read_current_timer delay [ 0.000292][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.000828][ T0] Console: colour dummy device 80x30 [ 0.000854][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000) [ 0.000868][ T0] pid_max: default: 32768 minimum: 301 [ 0.000986][ T0] LSM: Security Framework initializing [ 0.001037][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001049][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001617][ T0] CPU: Testing write buffer coherency: ok [ 0.001642][ T0] CPU0: Spectre v2: using BPIALL workaround [ 0.001767][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002228][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.002336][ T1] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 [ 0.002451][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.002561][ T1] rcu: Hierarchical SRCU implementation. [ 0.003056][ T1] smp: Bringing up secondary CPUs ... [ 0.003065][ T1] smp: Brought up 1 node, 1 CPU [ 0.003074][ T1] SMP: Total of 1 processors activated (1332.00 BogoMIPS). [ 0.003082][ T1] CPU: All CPU(s) started in SVC mode. [ 0.003356][ T1] devtmpfs: initialized [ 0.006201][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.006406][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.006426][ T1] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.020198][ T19] wait_for_initramfs() called before rootfs_initcalls [ 0.029015][ T1] prandom32: self test passed (less than 6 bits correlated) [ 0.029030][ T1] prandom: seed boundary self test passed [ 0.030653][ T1] prandom: 100 self tests passed [ 0.030662][ T1] pinctrl core: initialized pinctrl subsystem [ 0.031749][ T1] NET: Registered protocol family 16 [ 0.032323][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.032907][ T1] audit: initializing netlink subsys (disabled) [ 0.033827][ T30] audit: type=2000 audit(0.030:1): state=initialized audit_enabled=0 res=1 [ 0.034919][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.036127][ T1] cpuidle: using governor ladder [ 0.036158][ T1] cpuidle: using governor menu [ 0.036219][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.036231][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.036380][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.036392][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.270752][ T1] raid6: int32x8 gen() 243 MB/s [ 0.440784][ T1] raid6: int32x8 xor() 167 MB/s [ 0.610142][ T1] raid6: int32x4 gen() 280 MB/s [ 0.780198][ T1] raid6: int32x4 xor() 174 MB/s [ 0.950171][ T1] raid6: int32x2 gen() 447 MB/s [ 1.120174][ T1] raid6: int32x2 xor() 262 MB/s [ 1.290155][ T1] raid6: int32x1 gen() 497 MB/s [ 1.460160][ T1] raid6: int32x1 xor() 208 MB/s [ 1.460167][ T1] raid6: using algorithm int32x1 gen() 497 MB/s [ 1.460174][ T1] raid6: .... xor() 208 MB/s, rmw enabled [ 1.460180][ T1] raid6: using intx1 recovery algorithm [ 1.460895][ T1] vgaarb: loaded [ 1.461373][ T1] SCSI subsystem initialized [ 1.462720][ T1] usbcore: registered new interface driver usbfs [ 1.462804][ T1] usbcore: registered new interface driver hub [ 1.462878][ T1] usbcore: registered new device driver usb [ 1.463406][ T1] mc: Linux media interface: v0.10 [ 1.463482][ T1] videodev: Linux video capture interface: v2.00 [ 1.463764][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.463774][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.463833][ T1] PTP clock support registered [ 1.467999][ T1] clocksource: Switched to clocksource arm_global_timer [ 1.508345][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.508420][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.522092][ T1] NET: Registered protocol family 2 [ 1.522195][ T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.522855][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.522885][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.522925][ T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.522970][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 1.523078][ T1] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 1.523115][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.523137][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.523259][ T1] NET: Registered protocol family 1 [ 1.524385][ T1] RPC: Registered named UNIX socket transport module. [ 1.524397][ T1] RPC: Registered udp transport module. [ 1.524404][ T1] RPC: Registered tcp transport module. [ 1.524410][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.524420][ T1] PCI: CLS 0 bytes, default 64 [ 1.524663][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.524832][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.277104][ T1] Initialise system trusted keyrings [ 2.277140][ T1] Key type blacklist registered [ 2.277655][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 2.277739][ T1] zbud: loaded [ 2.278937][ T1] NFS: Registering the id_resolver key type [ 2.278959][ T1] Key type id_resolver registered [ 2.278966][ T1] Key type id_legacy registered [ 2.278992][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.279005][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.279012][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.340274][ T1] xor: measuring software checksum speed [ 2.344814][ T1] arm4regs : 2172 MB/sec [ 2.350873][ T1] 8regs : 1637 MB/sec [ 2.356555][ T1] 32regs : 1733 MB/sec [ 2.356562][ T1] xor: using function: arm4regs (2172 MB/sec) [ 2.356574][ T1] async_tx: api initialized (async) [ 2.356582][ T1] Key type asymmetric registered [ 2.356589][ T1] Asymmetric key parser 'x509' registered [ 2.356764][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 2.356830][ T1] io scheduler bfq registered [ 2.358805][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.360086][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 2.361598][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 2.363910][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.418582][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.420236][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.478589][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.582591][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.586336][ T1] printk: console [ttyS0] disabled [ 2.607533][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 12500000) is a 16550A [ 3.596779][ T1] printk: console [ttyS0] enabled [ 3.603033][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 3.612338][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 3.620731][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 3.629385][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.639296][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.650312][ T1] scsi host0: ahci-mvebu [ 3.655245][ T1] scsi host1: ahci-mvebu [ 3.659810][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 51 [ 3.668703][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 51 [ 3.678750][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 3.685844][ T1] nand: Macronix MX30LF2G18AC [ 3.691058][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.699982][ T1] Bad block table found at page 131008, version 0x01 [ 3.707199][ T1] Bad block table found at page 130944, version 0x01 [ 3.714147][ T1] nand_read_bbt: bad block at 0x000001ae0000 [ 3.720158][ T1] 7 fixed-partitions partitions found on MTD device pxa3xx_nand-0 [ 3.727861][ T1] Creating 7 MTD partitions on "pxa3xx_nand-0": [ 3.734018][ T1] 0x000000000000-0x000000200000 : "U-Boot" [ 3.740801][ T1] 0x000000200000-0x000000400000 : "U-Boot env" [ 3.748290][ T1] 0x000000400000-0x000000e00000 : "Config" [ 3.755360][ T1] 0x000000e00000-0x000001d00000 : "Kernel-1" [ 3.762688][ T1] 0x000001d00000-0x000008700000 : "RootFS-1" [ 3.770257][ T1] 0x000008700000-0x000009600000 : "Kernel-2" [ 3.777564][ T1] 0x000009600000-0x000010000000 : "RootFS-2" [ 3.785879][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.795465][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 3.807394][ T1] libphy: Fixed MDIO Bus: probed [ 3.815768][ T1] libphy: orion_mdio_bus: probed [ 3.825587][ T1] mvneta f1070000.ethernet eth0: Using random mac address b6:80:be:a6:07:83 [ 3.836767][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.844581][ T1] ehci-pci: EHCI PCI platform driver [ 3.850089][ T1] ehci-orion: EHCI orion driver [ 3.854972][ T1] orion-ehci f1058000.usb: EHCI Host Controller [ 3.861292][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.869781][ T1] orion-ehci f1058000.usb: irq 47, io mem 0xf1058000 [ 3.898037][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.904874][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.913927][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.921921][ T1] usb usb1: Product: EHCI Host Controller [ 3.927544][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd [ 3.934741][ T1] usb usb1: SerialNumber: f1058000.usb [ 3.940578][ T1] hub 1-0:1.0: USB hub found [ 3.945305][ T1] hub 1-0:1.0: 1 port detected [ 3.951013][ T1] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.957619][ T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.966001][ T1] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.976113][ T1] xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000 [ 3.982906][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.991970][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.999965][ T1] usb usb2: Product: xHCI Host Controller [ 4.005589][ T1] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.012804][ T1] usb usb2: SerialNumber: f10f0000.usb3 [ 4.018691][ T1] hub 2-0:1.0: USB hub found [ 4.023416][ T1] hub 2-0:1.0: 1 port detected [ 4.028422][ T1] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 4.034477][ T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 4.042956][ T1] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 4.050158][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.059201][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 4.068231][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.076196][ T1] usb usb3: Product: xHCI Host Controller [ 4.081821][ T1] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.089094][ T1] usb usb3: SerialNumber: f10f0000.usb3 [ 4.094938][ T1] hub 3-0:1.0: USB hub found [ 4.099667][ T1] hub 3-0:1.0: 1 port detected [ 4.104946][ T1] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.111435][ T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 4.119785][ T1] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.129943][ T1] xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000 [ 4.136639][ T1] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 4.145708][ T1] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.153696][ T1] usb usb4: Product: xHCI Host Controller [ 4.159316][ T1] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.166492][ T1] usb usb4: SerialNumber: f10f8000.usb3 [ 4.172422][ T1] hub 4-0:1.0: USB hub found [ 4.177126][ T1] hub 4-0:1.0: 1 port detected [ 4.182127][ T1] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.188220][ T1237] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 4.195161][ T1242] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 4.202367][ T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 4.210780][ T1242] ata2.00: ATA-8: TOSHIBA DT01ACA300, MX6OABB0, max UDMA/133 [ 4.218101][ T1] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 4.225212][ T1242] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 32) [ 4.232536][ T1] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.241394][ T49] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 4.248957][ T1] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 4.258031][ T1] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.266060][ T1] usb usb5: Product: xHCI Host Controller [ 4.271701][ T1242] ata2.00: configured for UDMA/133 [ 4.276730][ T1] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.283926][ T1] usb usb5: SerialNumber: f10f8000.usb3 [ 4.289807][ T1] hub 5-0:1.0: USB hub found [ 4.294509][ T1] hub 5-0:1.0: 1 port detected [ 4.299792][ T1] usbcore: registered new interface driver usblp [ 4.306637][ T1] usbcore: registered new interface driver usb-storage [ 4.313749][ T1] mousedev: PS/2 mouse device common for all mice [ 4.321749][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 4.328914][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2021-08-28T16:12:33 UTC (1630167153) [ 4.339431][ T1] i2c /dev entries driver [ 4.344445][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 4.353476][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 4.365569][ T1] orion_wdt: Initial timeout 171 sec [ 4.371743][ T1] device-mapper: uevent: version 1.0.3 [ 4.377526][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 4.387138][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 4.394518][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 4.401914][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 4.409361][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 4.416229][ T1] device-mapper: raid: Loading target version 1.15.1 [ 4.428235][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered [ 4.436605][ T1] hid: raw HID events driver (C) Jiri Kosina [ 4.443178][ T1] usbcore: registered new interface driver usbhid [ 4.450017][ T1] usbhid: USB HID core driver [ 4.454936][ T1] drop_monitor: Initializing network drop monitor service [ 4.462673][ T1] NET: Registered protocol family 10 [ 4.468739][ T1] Segment Routing with IPv6 [ 4.473132][ T1] RPL Segment Routing with IPv6 [ 4.477911][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.485870][ T1] NET: Registered protocol family 17 [ 4.491765][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 4.496704][ T49] usb 1-1: New USB device found, idVendor=05dc, idProduct=b051, bcdDevice= 8.15 [ 4.505711][ T1] Key type dns_resolver registered [ 4.510736][ T49] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=5 [ 4.518720][ T1] ThumbEE CPU extension supported. [ 4.523724][ T1] Registering SWP/SWPB emulation handler [ 4.529260][ T49] usb 1-1: Product: microSD RDR [ 4.534080][ T49] usb 1-1: Manufacturer: Lexar [ 4.539005][ T1] registered taskstats version 1 [ 4.543828][ T1] Loading compiled-in X.509 certificates [ 4.549468][ T49] usb 1-1: SerialNumber: 000000000001 [ 4.555181][ T1] zswap: loaded using pool lzo/zbud [ 4.560521][ T49] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.567814][ T1] Key type ._fscrypt registered [ 4.572857][ T49] scsi host2: usb-storage 1-1:1.0 [ 4.577962][ T1] Key type .fscrypt registered [ 4.583489][ T1] Key type fscrypt-provisioning registered [ 4.590023][ T1] Key type big_key registered [ 4.595236][ T1] Key type encrypted registered [ 4.602344][ T575] v5.0-sata0: supplied by pwr_en_sata0 [ 4.607913][ T575] v12.0-sata0: supplied by pwr_en_sata0 [ 4.615036][ T575] v5.0-sata1: supplied by pwr_en_sata1 [ 4.621169][ T575] v12.0-sata1: supplied by pwr_en_sata1 [ 4.627971][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.635497][ T1237] ata1.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133 [ 4.643555][ T1237] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 32) [ 4.658342][ T1237] ata1.00: configured for UDMA/133 [ 4.673679][ T18] scsi 0:0:0:0: Direct-Access ATA WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5 [ 4.683267][ T575] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 4.692267][ T538] scsi 1:0:0:0: Direct-Access ATA TOSHIBA DT01ACA3 ABB0 PQ: 0 ANSI: 5 [ 4.701578][ T575] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.708311][ T18] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 4.716803][ T18] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 4.723459][ T575] sd 0:0:0:0: [sda] Write Protect is off [ 4.729138][ T575] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.739046][ T18] sd 1:0:0:0: [sdb] Write Protect is off [ 4.744622][ T18] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.797345][ T18] sdb: sdb1 [ 4.801340][ T18] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 4.808046][ T575] sda: sda1 sda2 sda3 sda4 [ 4.813773][ T575] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 4.820753][ T1] md: Waiting for all devices to be available before autodetect [ 4.828441][ T1] md: If you don't use raid, use raid=noautodetect [ 4.834835][ T1] md: Autodetecting RAID arrays. [ 4.839757][ T1] md: autorun ... [ 4.843266][ T1] md: ... autorun DONE. [ 4.847560][ T1] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 4.855829][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 4.864965][ T1] 1f00 2048 mtdblock0 [ 4.864971][ T1] (driver?) [ 4.873001][ T1] 1f01 2048 mtdblock1 [ 4.873006][ T1] (driver?) [ 4.881002][ T1] 1f02 10240 mtdblock2 [ 4.881006][ T1] (driver?) [ 4.889004][ T1] 1f03 15360 mtdblock3 [ 4.889009][ T1] (driver?) [ 4.896982][ T1] 1f04 108544 mtdblock4 [ 4.896986][ T1] (driver?) [ 4.904971][ T1] 1f05 15360 mtdblock5 [ 4.904975][ T1] (driver?) [ 4.912956][ T1] 1f06 108544 mtdblock6 [ 4.912961][ T1] (driver?) [ 4.920938][ T1] 0800 2930266584 sda [ 4.920943][ T1] driver: sd [ 4.928485][ T1] 0801 262144 sda1 33b34d1e-2343-4d36-a33f-269013ebf582 [ 4.928490][ T1] [ 4.938476][ T1] 0802 16121856 sda2 6b76ce52-146f-4979-8b57-e789943f2467 [ 4.938481][ T1] [ 4.948465][ T1] 0803 2909785088 sda3 1e270746-2a32-4458-8d89-9d5a1081c7c1 [ 4.948470][ T1] [ 4.958455][ T1] 0804 4096000 sda4 b0250eac-3bce-4a86-bf15-f463554f32e2 [ 4.958460][ T1] [ 4.968448][ T1] 0810 2930266584 sdb [ 4.968453][ T1] driver: sd [ 4.975988][ T1] 0811 2930265088 sdb1 2aac4fc0-154e-4a7b-a1ac-040887b07eaf [ 4.975992][ T1] [ 4.985982][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 4.994991][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.8-mvebu-tld-1 #1.0 [ 5.002866][ T1] Hardware name: Marvell Armada 380/385 (Device Tree) [ 5.009523][ T1] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 5.018025][ T1] [] (show_stack) from [] (dump_stack+0x80/0x9c) [ 5.025995][ T1] [] (dump_stack) from [] (panic+0xe4/0x2f0) [ 5.033617][ T1] [] (panic) from [] (mount_block_root+0x1b4/0x238) [ 5.041851][ T1] [] (mount_block_root) from [] (mount_root+0xf0/0x11c) [ 5.050431][ T1] [] (mount_root) from [] (prepare_namespace+0x144/0x180) [ 5.059186][ T1] [] (prepare_namespace) from [] (kernel_init_freeable+0x230/0x29c) [ 5.068814][ T1] [] (kernel_init_freeable) from [] (kernel_init+0x8/0x118) [ 5.077745][ T1] [] (kernel_init) from [] (ret_from_fork+0x14/0x24) [ 5.086063][ T1] Exception stack(0xc14a3fb0 to 0xc14a3ff8) [ 5.091843][ T1] 3fa0: 00000000 00000000 00000000 00000000 [ 5.100765][ T1] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 5.109687][ T1] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 5.117043][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---