Terminal log file Date: 09.11.2022 - 23:17:48 ----------------------------------------------- reboot root@StoraWrt:/# [ 69.909959] br-lan: port 1(eth0) entered disabled state [ 69.923460] device eth0 left promiscuous mode [ 69.927934] br-lan: port 1(eth0) entered disabled state [ 74.166054] reboot: Restarting system U-Boot 2020.04 (Jul 10 2020 - 13:03:49 +0000) Netgear Stora MS2110 SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out 88E1116 Initialized on egiga0 IDE: ide_preinit failed Hit any key to stop autoboot: 2  0 Netgear Stora> setenv mainlineLinux yes Netgear Stora> setenv arcNumber 2743 Netgear Stora> setenv ipaddr 192.168.88.121 Netgear Stora> setenv serverip 192.168.88.10 Netgear Stora> tftpboot 0x200000 uImage Using egiga0 device TFTP from server 192.168.88.10; our IP address is 192.168.88.121 Filename 'uImage'. Load address: 0x200000 Loading: *################################################################# ################################################################# ###################################### 1.6 MiB/s done Bytes transferred = 2463519 (25971f hex) Netgear Stora> tftpboot 0x800000 uInitrd Using egiga0 device TFTP from server 192.168.88.10; our IP address is 192.168.88.121 Filename 'uInitrd'. Load address: 0x800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 1.3 MiB/s done Bytes transferred = 10546955 (a0ef0b hex) Netgear Stora> setenv bootargs console=ttyS0,115200n8 base-installer/initramfs-tools/driver-policy=most Netgear Stora> bootm 0x200000 0x800000 ## Booting kernel from Legacy Image at 00200000 ... Image Name: Debian kernel Created: 2022-09-06 20:55:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2463455 Bytes = 2.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00800000 ... Image Name: debian-installer ramdisk Created: 2022-09-06 20:55:12 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 10546891 Bytes = 10.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image Loading Ramdisk to 035f1000, end 03fffecb ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.0-18-marvell (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Debian 5.10.140-1 (2022-09-02) [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: OpenRD Base [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200n8 base-installer/initramfs-tools/driver-policy=most [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 111944K/131072K available (4748K kernel code, 825K rwdata, 1312K rodata, 292K init, 224K bss, 19128K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] ftrace: allocating 22276 entries in 66 pages [ 0.000000] ftrace: allocated 66 pages with 2 groups [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000062] Switching to timer-based delay loop, resolution 5ns [ 0.000266] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=800000) [ 0.000305] pid_max: default: 32768 minimum: 301 [ 0.001030] LSM: Security Framework initializing [ 0.001317] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.001719] AppArmor: AppArmor initialized [ 0.001974] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002013] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.004499] CPU: Testing write buffer coherency: ok [ 0.006983] Setting up static identity map for 0x8200 - 0x823c [ 0.007336] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.008967] devtmpfs: initialized [ 0.014496] VFP support v0.3: not present [ 0.014721] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.014770] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.015020] pinctrl core: initialized pinctrl subsystem [ 0.017761] NET: Registered protocol family 16 [ 0.018654] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.019839] audit: initializing netlink subsys (disabled) [ 0.020499] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1 [ 0.021506] thermal_sys: Registered thermal governor 'fair_share' [ 0.021523] thermal_sys: Registered thermal governor 'bang_bang' [ 0.021548] thermal_sys: Registered thermal governor 'step_wise' [ 0.021563] thermal_sys: Registered thermal governor 'user_space' [ 0.021675] cpuidle: using governor ladder [ 0.021703] cpuidle: using governor menu [ 0.022152] Feroceon L2: Enabling L2 [ 0.022216] Feroceon L2: Cache support initialised. [ 0.038459] No ATAGs? [ 0.048767] clocksource: Switched to clocksource orion_clocksource [ 0.106418] VFS: Disk quotas dquot_6.6.0 [ 0.106564] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107498] AppArmor: AppArmor Filesystem Enabled [ 0.109430] NET: Registered protocol family 2 [ 0.109746] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.110784] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.111091] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.111126] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.111152] TCP: Hash tables configured (established 1024 bind 1024) [ 0.111324] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.111364] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.111690] NET: Registered protocol family 1 [ 0.111739] PCI: CLS 0 bytes, default 32 [ 0.112200] Trying to unpack rootfs image as initramfs... [ 1.226285] Freeing initrd memory: 10300K [ 1.227333] Initialise system trusted keyrings [ 1.227462] Key type blacklist registered [ 1.227827] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.234485] zbud: loaded [ 1.235414] Key type asymmetric registered [ 1.235435] Asymmetric key parser 'x509' registered [ 1.235500] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.238770] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 1.239570] gpio-28 (SelRS232or485): hogged as output/low [ 1.240578] gpio-34 (SelUARTorSD): hogged as output/high [ 1.241559] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 1.241620] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 1.241662] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 1.241690] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 1.241967] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 1.241994] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.242017] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 1.242035] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 1.242052] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 1.242168] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 1.243678] PCI: bus0: Fast back to back transfers disabled [ 1.243702] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.244955] PCI: bus1: Fast back to back transfers enabled [ 1.244980] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.245209] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.246048] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.282569] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.283093] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.318556] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.319298] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.320833] printk: console [ttyS0] disabled [ 1.320946] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 1.958861] printk: console [ttyS0] enabled [ 1.964255] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 26, base_baud = 12500000) is a 16550A [ 1.975120] i2c /dev entries driver [ 1.979792] ledtrig-cpu: registered to indicate activity on CPUs [ 1.986713] registered taskstats version 1 [ 1.990870] Loading compiled-in X.509 certificates [ 2.012537] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 2.021760] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 2.032652] AppArmor: AppArmor sha1 policy hashing enabled [ 2.046182] Freeing unused kernel memory: 292K [ 2.050681] Kernel memory protection not selected by kernel config. [ 2.057013] Run /init as init process [ 2.396943] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 2.403372] nand: Samsung NAND 256MiB 3,3V 8-bit [ 2.408035] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.479399] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.532932] Scanning device for bad blocks [ 2.550575] usbcore: registered new interface driver usbfs [ 2.562795] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 2.579799] kirkwood-pinctrl f1010000.pin-controller: pin PIN13 already requested by f1012100.serial; cannot claim for f1090000.mvsdio [ 2.592013] kirkwood-pinctrl f1010000.pin-controller: pin-13 (f1090000.mvsdio) status -22 [ 2.600259] kirkwood-pinctrl f1010000.pin-controller: could not request pin 13 (PIN13) from group mpp13 on device f1010000.pin-controller [ 2.612774] mvsdio f1090000.mvsdio: Error applying setting, reverse things back [ 2.627627] Bad eraseblock 64 at 0x000000800000 [ 2.651110] usbcore: registered new interface driver hub [ 2.661294] Bad eraseblock 65 at 0x000000820000 [ 2.681024] usbcore: registered new device driver usb [ 2.700356] Bad eraseblock 125 at 0x000000fa0000 [ 2.806644] mvsdio: probe of f1090000.mvsdio failed with error -22 [ 2.821836] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.849341] ehci-orion: EHCI orion driver [ 2.861920] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.885870] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.901927] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 2.928829] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.939743] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 2.948093] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.955373] usb usb1: Product: EHCI Host Controller [ 2.960298] usb usb1: Manufacturer: Linux 5.10.0-18-marvell ehci_hcd [ 2.966708] usb usb1: SerialNumber: f1050000.ehci [ 2.997066] Bad eraseblock 1250 at 0x000009c40000 [ 3.009579] hub 1-0:1.0: USB hub found [ 3.018078] hub 1-0:1.0: 1 port detected [ 3.129865] 3 fixed-partitions partitions found on MTD device orion_nand [ 3.136662] Creating 3 MTD partitions on "orion_nand": [ 3.142005] 0x000000000000-0x000000100000 : "u-boot" [ 3.149780] 0x000000100000-0x000000500000 : "uImage" [ 3.157486] 0x000000600000-0x000020000000 : "root" [ 3.162354] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0xfa00000 Starting system log daemon: syslogd, klogd.  ----------------------------------------------- Date: 09.11.2022 - 23:36:38 End log file