U-Boot 2023.01-rc1-00041-g0cbeed4f66-dirty (Nov 25 2022 - 15:12:20 +0100) SoC: MV78230-B0 at 1066 MHz DRAM: 512 MiB (533 MHz, 32-bit, ECC not enabled) Core: 20 devices, 15 uclasses, devicetree: separate Loading Environment from SPIFlash... SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB OK In: serial@12000 Out: serial@12000 Err: serial@12000 Model: Synology DS214 Board: DS414 Net: No ethernet found. => run starttftp pcie0.0: Link up starting USB... Bus xhci_pci: Register 4000440 NbrPorts 4 Starting the controller USB XHCI 1.00 scanning bus xhci_pci for devices... Warning: asix_eth MAC addresses don't match: Address in ROM is 00:00:00:00:03:66 Address in environment is 00:50:43:02:02:00 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Waiting for Ethernet connection... done. Using asix_eth device TFTP from server 192.168.1.20; our IP address is 192.168.1.190 Filename 'uImage'. Load address: 0x2000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################### 931.6 KiB/s done Bytes transferred = 5401120 (526a20 hex) 10418159 bytes read in 245 ms (40.6 MiB/s) ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-6.0.8-mvebu-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5401056 Bytes = 5.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 08000000 ... Image Name: initramfs-6.0.7-mvebu-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 10418095 Bytes = 9.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Working FDT set to 0 Loading Kernel Image Starting kernel ... DTB:0x0052A898 (0x00004148) C:0x000080E0-0x0052EAA0->0x0127F900-0x017A62C0 DTB:0x017A20B8 (0x000041F1) Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.0.8-mvebu-tld-1 (root@67e0d50e71cc) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #5 SMP PREEMPT Sat Nov 26 14:44:49 UTC 2022 [ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: div instructions available: patching division code [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Synology DS214 [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] HighMem empty [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] percpu: Embedded 17 pages/cpu s38996 r8192 d22444 u69632 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: "console=ttyS0,115200 root=/dev/sda1 rootdelay=5 $mtdparts earlyprintk=serial syno_hw_version=DS214v10 ihd_num=2 netif_num=1 flash_size=8" [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 488936K/524288K available (11264K kernel code, 1531K rwdata, 3552K rodata, 1024K init, 468K bss, 35352K reserved, 0K cma-reserved, 0K highmem) [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a096b00 -> 0x1a096b02 [ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB [ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a096b02 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval) [ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns [ 0.000001][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.000018][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.001259][ T0] Console: colour dummy device 80x30 [ 0.001302][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.001320][ T0] pid_max: default: 32768 minimum: 301 [ 0.001654][ T0] LSM: Security Framework initializing [ 0.001858][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001875][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003006][ T0] CPU: Testing write buffer coherency: ok [ 0.003370][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004878][ T1] cblist_init_generic: Setting adjustable number of callback queues. [ 0.004890][ T1] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.005054][ T1] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.005221][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.005584][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2 [ 0.005724][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.005978][ T1] rcu: Hierarchical SRCU implementation. [ 0.005986][ T1] rcu: Max phase no-delay instances is 1000. [ 0.007122][ T1] smp: Bringing up secondary CPUs ... [ 0.008129][ T1] Booting CPU 1 [ 0.008562][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.018648][ T1] smp: Brought up 1 node, 2 CPUs [ 0.018661][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.018670][ T1] CPU: All CPU(s) started in SVC mode. [ 0.019376][ T1] devtmpfs: initialized [ 0.024881][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.025238][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025276][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.025478][ T1] prandom: seed boundary self test passed [ 0.028298][ T1] prandom: 100 self tests passed [ 0.028306][ T1] pinctrl core: initialized pinctrl subsystem [ 0.030004][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.030435][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.031504][ T1] audit: initializing netlink subsys (disabled) [ 0.031848][ T24] audit: type=2000 audit(0.030:1): state=initialized audit_enabled=0 res=1 [ 0.032569][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.032916][ T1] cpuidle: using governor ladder [ 0.032962][ T1] cpuidle: using governor menu [ 0.033041][ T16] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 [ 0.033052][ T16] hw-breakpoint: CPU 0 failed to disable vector catch [ 0.033089][ T17] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 [ 0.240173][ T1] raid6: int32x8 gen() 188 MB/s [ 0.410153][ T1] raid6: int32x4 gen() 204 MB/s [ 0.580140][ T1] raid6: int32x2 gen() 340 MB/s [ 0.750125][ T1] raid6: int32x1 gen() 352 MB/s [ 0.750134][ T1] raid6: using algorithm int32x1 gen() 352 MB/s [ 0.920077][ T1] raid6: .... xor() 169 MB/s, rmw enabled [ 0.920085][ T1] raid6: using intx1 recovery algorithm [ 0.921299][ T1] SCSI subsystem initialized [ 0.921893][ T1] usbcore: registered new interface driver usbfs [ 0.921953][ T1] usbcore: registered new interface driver hub [ 0.922004][ T1] usbcore: registered new device driver usb [ 0.922374][ T1] pps_core: LinuxPPS API ver. 1 registered [ 0.922382][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.922405][ T1] PTP clock support registered [ 0.924068][ T1] vgaarb: loaded [ 0.924671][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.925497][ T1] VFS: Disk quotas dquot_6.6.0 [ 0.925602][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.938956][ T1] NET: Registered PF_INET protocol family [ 0.939178][ T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.940487][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.940597][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.940630][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.940676][ T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.940720][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 0.940950][ T1] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.941027][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.941054][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.941318][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.942129][ T1] RPC: Registered named UNIX socket transport module. [ 0.942140][ T1] RPC: Registered udp transport module. [ 0.942146][ T1] RPC: Registered tcp transport module. [ 0.942151][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.942162][ T1] PCI: CLS 0 bytes, default 64 [ 0.942247][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.942619][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.945170][ T8] Trying to unpack rootfs image as initramfs... [ 1.333955][ T1] Initialise system trusted keyrings [ 1.334041][ T1] Key type blacklist registered [ 1.335279][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 1.335459][ T1] zbud: loaded [ 1.337445][ T1] NFS: Registering the id_resolver key type [ 1.337517][ T1] Key type id_resolver registered [ 1.337525][ T1] Key type id_legacy registered [ 1.337570][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.337586][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.429693][ T1] xor: measuring software checksum speed [ 1.438909][ T1] arm4regs : 1072 MB/sec [ 1.451838][ T1] 8regs : 767 MB/sec [ 1.462017][ T1] 32regs : 973 MB/sec [ 1.462031][ T1] xor: using function: arm4regs (1072 MB/sec) [ 1.462052][ T1] async_tx: api initialized (async) [ 1.462066][ T1] Key type asymmetric registered [ 1.462073][ T1] Asymmetric key parser 'x509' registered [ 1.545330][ T8] Freeing initrd memory: 10176K [ 1.569463][ T1] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.569683][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.569889][ T1] io scheduler bfq registered [ 1.574016][ T1] armada-xp-pinctrl f1018000.pin-ctrl: registered pinctrl driver [ 1.577052][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 1.578262][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 1.579195][ T1] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: [ 1.579277][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 1.579318][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000 [ 1.579356][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1048000..0x00f1049fff -> 0x0000048000 [ 1.579393][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f104c000..0x00f104dfff -> 0x000004c000 [ 1.579430][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000 [ 1.579467][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 1.579502][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 1.579537][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 1.579572][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 1.579607][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 1.579642][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 1.579676][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 1.579711][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 1.579746][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 1.579771][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 1.579877][ T1] mvebu-pcie soc:pcie@82000000: pcie0.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@1,0 does not contain intx interrupt [ 1.579953][ T1] mvebu-pcie soc:pcie@82000000: pcie1.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@5,0 does not contain intx interrupt [ 1.580317][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 1.580332][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.580350][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 1.580365][ T1] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff]) [ 1.580378][ T1] pci_bus 0000:00: root bus resource [mem 0xf1048000-0xf1049fff] (bus address [0x00048000-0x00049fff]) [ 1.580392][ T1] pci_bus 0000:00: root bus resource [mem 0xf104c000-0xf104dfff] (bus address [0x0004c000-0x0004dfff]) [ 1.580405][ T1] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff]) [ 1.580417][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 1.580428][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 1.580564][ T1] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400 [ 1.581317][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400 [ 1.582913][ T1] PCI: bus0: Fast back to back transfers disabled [ 1.582939][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.582971][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.583245][ T1] pci 0000:01:00.0: [1b6f:7023] type 00 class 0x0c0330 [ 1.583286][ T1] pci 0000:01:00.0: reg 0x10: [mem 0xc0000000-0xc0007fff 64bit] [ 1.583356][ T1] pci 0000:01:00.0: enabling Extended Tags [ 1.583449][ T1] pci 0000:01:00.0: supports D1 D2 [ 1.583459][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot [ 1.583833][ T1] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 1.604763][ T1] PCI: bus1: Fast back to back transfers disabled [ 1.604785][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.605094][ T1] PCI: bus2: Fast back to back transfers enabled [ 1.605113][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.605168][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff] [ 1.605188][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8007fff 64bit] [ 1.605213][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.605229][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 1.605257][ T1] pci 0000:00:05.0: PCI bridge to [bus 02] [ 1.605361][ T1] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 1.606210][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.665946][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.669964][ T1] mv_xor f10f0900.xor: Marvell shared XOR driver [ 1.725941][ T1] mv_xor f10f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.871191][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.875619][ T1] printk: console [ttyS0] disabled [ 1.895850][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 35, base_baud = 15625000) is a 16550A [ 3.280612][ T1] printk: console [ttyS0] enabled [ 3.307568][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 36, base_baud = 15625000) is a 16550A [ 3.322683][ T1] sata_mv f10a0000.sata: slots 32 ports 2 [ 3.331357][ T1] scsi host0: sata_mv [ 3.336445][ T1] scsi host1: sata_mv [ 3.340894][ T1] ata1: SATA max UDMA/133 irq 37 [ 3.345761][ T1] ata2: SATA max UDMA/133 irq 37 [ 3.354791][ T1] spi-nor spi0.0: n25q064 (8192 Kbytes) [ 3.360407][ T1] 6 fixed-partitions partitions found on MTD device spi0.0 [ 3.367516][ T1] Creating 6 MTD partitions on "spi0.0": [ 3.373031][ T1] 0x000000000000-0x0000000d0000 : "RedBoot" [ 3.381248][ T1] 0x0000000d0000-0x0000003a0000 : "zImage" [ 3.389279][ T1] 0x0000003a0000-0x0000007d0000 : "rd.gz" [ 3.397190][ T1] 0x0000007d0000-0x0000007e0000 : "vendor" [ 3.405300][ T1] 0x0000007e0000-0x0000007f0000 : "RedBoot config" [ 3.413954][ T1] 0x0000007f0000-0x000000800000 : "FIS directory" [ 3.423339][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.431946][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 3.463761][ T1] hwmon hwmon0: temp1_input not attached to any thermal zone [ 3.476981][ T1] mvneta f1070000.ethernet eth0: Using random mac address e2:2f:54:1d:fe:f5 [ 3.486846][ T1] sky2: driver version 1.30 [ 3.491645][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.499001][ T1] ehci-pci: EHCI PCI platform driver [ 3.504369][ T1] ehci-orion: EHCI orion driver [ 3.509481][ T1] orion-ehci f1050000.usb: EHCI Host Controller [ 3.515696][ T1] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1 [ 3.524116][ T1] orion-ehci f1050000.usb: irq 39, io mem 0xf1050000 [ 3.554699][ T1] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00 [ 3.561779][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 3.570841][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.578817][ T1] usb usb1: Product: EHCI Host Controller [ 3.584416][ T1] usb usb1: Manufacturer: Linux 6.0.8-mvebu-tld-1 ehci_hcd [ 3.591510][ T1] usb usb1: SerialNumber: f1050000.usb [ 3.597962][ T1] hub 1-0:1.0: USB hub found [ 3.602483][ T1] hub 1-0:1.0: 1 port detected [ 3.609032][ T1] usbcore: registered new interface driver usblp [ 3.615525][ T1] usbcore: registered new interface driver usb-storage [ 3.623087][ T1] mousedev: PS/2 mouse device common for all mice [ 3.631131][ T1] i2c_dev: i2c /dev entries driver [ 3.637439][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 3.651360][ T1] rtc-s35390a 0-0030: registered as rtc0 [ 3.657275][ T1] rtc-s35390a 0-0030: setting system clock to 2022-11-26T15:01:39 UTC (1669474899) [ 3.676396][ T686] ata1: SATA link down (SStatus 0 SControl F300) [ 3.771724][ T1] orion_wdt: Initial timeout 171 sec [ 3.778493][ T1] device-mapper: uevent: version 1.0.3 [ 3.784224][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 3.793941][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 3.801227][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 3.808583][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 3.815994][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 3.822811][ T1] device-mapper: raid: Loading target version 1.15.1 [ 3.830918][ T1] debugfs: Directory 'cpu1' with parent 'opp' already present! [ 3.841155][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered [ 3.849818][ T1] hid: raw HID events driver (C) Jiri Kosina [ 3.856551][ T1] usbcore: registered new interface driver usbhid [ 3.862853][ T1] usbhid: USB HID core driver [ 3.868165][ T1] drop_monitor: Initializing network drop monitor service [ 3.876247][ T1] NET: Registered PF_INET6 protocol family [ 3.883513][ T1] Segment Routing with IPv6 [ 3.887931][ T1] RPL Segment Routing with IPv6 [ 3.892713][ T1] In-situ OAM (IOAM) with IPv6 [ 3.897467][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.906670][ T1] NET: Registered PF_PACKET protocol family [ 3.912706][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 3.917762][ T1] Key type dns_resolver registered [ 3.922838][ T1] ThumbEE CPU extension supported. [ 3.927892][ T1] Registering SWP/SWPB emulation handler [ 3.934251][ T1] registered taskstats version 1 [ 3.939163][ T1] Loading compiled-in X.509 certificates [ 3.945411][ T1] zswap: loaded using pool lzo/zbud [ 3.951202][ T1] Key type .fscrypt registered [ 3.955890][ T1] Key type fscrypt-provisioning registered [ 3.963814][ T1] Key type big_key registered [ 3.991736][ T1] Key type encrypted registered [ 4.006762][ T691] ata2: SATA link down (SStatus 0 SControl F300) [ 10.162080][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 10.197551][ T1] Checked W+X mappings: passed, no W+X pages found [ 10.203970][ T1] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 12.080669][ T1004] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 12.094548][ T1004] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 12.185207][ T1004] xhci_hcd 0000:01:00.0: hcc params 0x040050a7 hci version 0x100 quirks 0x0000000000080490 [ 12.212497][ T1004] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 12.227098][ T1004] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 12.243652][ T1004] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 12.259606][ T1004] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 12.274961][ T1004] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.292494][ T1004] usb usb2: Product: xHCI Host Controller [ 12.309056][ T1004] usb usb2: Manufacturer: Linux 6.0.8-mvebu-tld-1 xhci-hcd [ 12.322829][ T1004] usb usb2: SerialNumber: 0000:01:00.0 [ 12.331925][ T1004] hub 2-0:1.0: USB hub found [ 12.344904][ T1004] hub 2-0:1.0: 2 ports detected [ 12.368934][ T1004] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.389269][ T1004] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00 [ 12.407817][ T1004] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.435620][ T1004] usb usb3: Product: xHCI Host Controller [ 12.441260][ T1004] usb usb3: Manufacturer: Linux 6.0.8-mvebu-tld-1 xhci-hcd [ 12.472582][ T1004] usb usb3: SerialNumber: 0000:01:00.0 [ 12.488449][ T1004] hub 3-0:1.0: USB hub found [ 12.503762][ T1004] hub 3-0:1.0: 2 ports detected [ 12.644872][ T1015] usb 2-1: new full-speed USB device number 2 using xhci_hcd [ 12.866156][ T1015] usb 2-1: not running at top speed; connect to a high speed hub [ 12.958091][ T1015] usb 2-1: New USB device found, idVendor=0b95, idProduct=7720, bcdDevice= 0.01 [ 12.970903][ T1015] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.984325][ T1015] usb 2-1: Product: AX88772 [ 12.989026][ T1015] usb 2-1: Manufacturer: ASIX Elec. Corp. [ 13.000770][ T1015] usb 2-1: SerialNumber: 000366 [ 13.164870][ T1015] usb 2-2: new high-speed USB device number 3 using xhci_hcd [ 13.412100][ T1015] usb 2-2: New USB device found, idVendor=0781, idProduct=55b0, bcdDevice= 3.05 [ 13.421115][ T1015] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 13.429032][ T1015] usb 2-2: Product: Portable SSD [ 13.433858][ T1015] usb 2-2: Manufacturer: SanDisk [ 13.438714][ T1015] usb 2-2: SerialNumber: 32323332315A343031383630 [ 13.498826][ T1010] scsi host2: uas [ 13.503640][ T1010] usbcore: registered new interface driver uas [ 13.505325][ T10] scsi 2:0:0:0: Direct-Access SanDisk Portable SSD 0305 PQ: 0 ANSI: 6 [ 13.530608][ T10] scsi 2:0:0:1: Enclosure SanDisk SES Device 0305 PQ: 0 ANSI: 6 [ 13.564183][ T45] sd 2:0:0:0: [sda] 937701376 512-byte logical blocks: (480 GB/447 GiB) [ 13.572736][ T45] sd 2:0:0:0: [sda] 4096-byte physical blocks [ 13.579696][ T45] sd 2:0:0:0: [sda] Write Protect is off [ 13.586985][ T45] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 13.597037][ T45] sd 2:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 13.604219][ T45] sd 2:0:0:0: [sda] Optimal transfer size 1048576 bytes [ 13.629693][ T45] sda: sda1 sda2 sda3 [ 13.635770][ T45] sd 2:0:0:0: [sda] Attached SCSI disk [ 13.667666][ T1010] scsi 2:0:0:1: Wrong diagnostic page; asked for 1 got 8 [ 13.685050][ T1010] scsi 2:0:0:1: Failed to get diagnostic page 0x1 [ 13.705252][ T1010] scsi 2:0:0:1: Failed to bind enclosure -19 [ 13.711802][ T1010] ses 2:0:0:1: Attached Enclosure device Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext2 (1) -- /dev/sda1] fsck.ext2 -a -C0 /dev/sda1 /dev/sda1: clean, 28333/1310720 files, 701684/5242880 blocks done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 23.671782][ T1220] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 23.694412][ T1220] ses 2:0:0:1: Attached scsi generic sg1 type 13 [ 25.526566][ T1219] Generic PHY usb-002:002:10: attached PHY driver (mii_bus:phy_addr=usb-002:002:10, irq=POLL) [ 25.557394][ T1219] asix 2-1:1.0 eth1: register 'asix' at usb-0000:01:00.0-1, ASIX AX88772 USB 2.0 Ethernet, 00:50:43:02:02:00 [ 25.608592][ T1219] usbcore: registered new interface driver asix [ 25.956608][ T1226] asix 2-1:1.0 enx005043020200: renamed from eth1 [ 27.104731][ C1] random: crng init done done. Not activating swap on swapfile. ... (warning). [ 27.959408][ T1426] ext2 filesystem being remounted at / supports timestamps until 2038 (0x7fffffff) Will now check all file systems. Checking all file systems. /dev/sda1 is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. [ 30.729085][ T1713] Adding 1048572k swap on /swapfile. Priority:-2 extents:16 across:2954944k SSFS Will now mount local filesystems:. Will now activate swapfile swap, if any:swapon: /swapfile: found signature [pagesize=4096, signature=swap] swapon: /swapfile: pagesize=4096, swapsize=1073741824, devsize=1073741824 swapon /swapfile done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Initializing random number generator...done. Starting Setting kernel variables: sysctl. [ 31.855906][ T1840] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL) [ 31.869608][ T1840] mvneta f1070000.ethernet eth0: configuring for phy/rgmii-id link mode Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 [ 35.035879][ T72] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 35.044490][ T72] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 17 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting fancontrol; run pwmconfig first. ... (warning). Not starting NFS kernel daemon: no exports. ... (warning). Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1986 (syslogd) . Starting periodic command scheduler: cron. Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting NTP server: ntpd. Starting OpenBSD Secure Shell server: sshd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2033 (klogd) . Running local boot scripts (/etc/rc.local) Cannot read environment, using default Cannot read default environment from file <13>Nov 26 07:03:13 root[2117]: Cannot read u-boot env ethaddr . Debian GNU/Linux 11 debian ttyS0 debian login: root