Marvell>> bootm 0xd00000 0x800000 0x01000000 bootm 0xd00000 0x800000 0x01000000 ## Booting kernel from Legacy Image at 00d00000 ... Image Name: Linux-3.10.108 Created: 2021-10-18 11:15:28 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2247000 Bytes = 2.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00800000 ... Image Name: synology_armada38x_ds218j 42218 Created: 2021-10-18 13:15:33 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3463856 Bytes = 3.3 MiB Load Address: 08000000 Entry Point: 08000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Kernel Image ... OK OK Loading Ramdisk to 1f6d9000, end 1fa26ab0 ... OK Loading Device Tree to 00ff8000, end 00fff30a ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. [00] BootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6820 High speed PHY - Version: 2.0 Init Synology board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 0 | SGMII0 | | 1 | 6 | SATA0 | | 2 | 6 | SATA1 | | 4 | 5 | USB3 HOST0 | | 5 | 5 | USB3 HOST1 | ------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-g15634d4 (Jun 27 2017 - 15:11:00) Marvell version: 2015_T1.0p16 Board: SYNO-DS218j SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR3 @ 666 [MHz] DDR3 16 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB MMC: mv_sdh: 0 SF: Detected MX25L6405D with page size 64 KiB, total 8 MiB USB3.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x1ff38000:0x1ffc9708 BSS: 0x1ffefaa8 Stack: 0x1fa27f20 Heap: 0x1fa28000:0x1ff38000 U-Boot Environment: 0x007e0000:0x007f0000 (SPI) Board configuration detected: Synology Model: DS218j Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | SGMII | 0x01 | egiga0 [PRIME] Press Ctrl+C to abort autoboot in 3 second (Re)start USB controller... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 USB1: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 SF: Detected MX25L6405D with page size 64 KiB, total 8 MiB ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-3.10.108 Created: 2022-09-21 2:56:09 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2251616 Bytes = 2.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: synology_armada38x_ds218j 42962 Created: 2022-09-22 10:07:49 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3528278 Bytes = 3.4 MiB Load Address: 08000000 Entry Point: 08000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Kernel Image ... OK OK Loading Ramdisk to 1f6c9000, end 1fa26656 ... OK Loading Device Tree to 00ff9000, end 00fffa9f ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.108 (root@build16) (gcc version 8.5.0 (GCC) ) #42962 SMP Wed Sep 21 10:55:38 CST 2022 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Synology DS218j [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @80a1b000 s7168 r8192 d13312 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x3000000 root=/dev/md0 rw syno_hw_version=DS218j syno_hdd_powerup_seq=2 ihd_num=2 netif_num=1 syno_hdd_enable=15,16 flash_size=8 [ 0.000000] Synology Hardware Version: DS218j-j [ 0.000000] Power on seq num: 2 [ 0.000000] Internal HD num: 2 [ 0.000000] Internal netif num: 1 [ 0.000000] SYNO GPIO hdd enable pin: 15 16 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 1048576 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 508964k/508964k available, 15324k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xa0800000 - 0xfff00000 (1527 MB) [ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB) [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) [ 0.000000] .text : 0x80008000 - 0x80542a70 (5355 kB) [ 0.000000] .init : 0x80543000 - 0x8057ac00 ( 223 kB) [ 0.000000] .data : 0x8057c000 - 0x805af3a0 ( 205 kB) [ 0.000000] .bss : 0x805af3a0 - 0x80610ab4 ( 390 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] [ 0.000000] LSP version: linux-3.10.70-2015_T1.1p7 [ 0.000000] [ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B [ 0.000459] Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) [ 0.060028] pid_max: default: 32768 minimum: 301 [ 0.060081] Security Framework initialized [ 0.060092] AppArmor: AppArmor initialized [ 0.060112] Mount-cache hash table entries: 512 [ 0.060482] Initializing cgroup subsys memory [ 0.060499] Initializing cgroup subsys devices [ 0.060503] Initializing cgroup subsys freezer [ 0.060507] Initializing cgroup subsys blkio [ 0.060533] CPU: Testing write buffer coherency: ok [ 0.060657] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.060694] Setting up static identity map for 0x803fba90 - 0x803fbae8 [ 0.060834] mvebu-pmsu: Initializing Power Management Service Unit [ 0.060868] Initializing CPU Reset module [ 0.061532] CPU1: Booted secondary processor [ 0.120628] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.120690] Brought up 2 CPUs [ 0.120699] SMP: Total of 2 processors activated (5311.69 BogoMIPS). [ 0.120702] CPU: All CPU(s) started in SVC mode. [ 0.121026] devtmpfs: initialized [ 0.123437] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.123637] pinctrl core: initialized pinctrl subsystem [ 0.123916] regulator-dummy: no parameters [ 0.124080] NET: Registered protocol family 16 [ 0.124663] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.126848] irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated [ 0.127221] irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated [ 0.130174] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.130180] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.136240] bio: create slab at 0 [ 0.136641] mvebu-pcie pcie-controller.3: PCIe0.0: link down [ 0.136667] mvebu-pcie pcie-controller.3: PCIe1.0: link down [ 0.136780] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 [ 0.136788] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.136794] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 0.136800] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.137046] PCI: bus0: Fast back to back transfers disabled [ 0.137054] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.137060] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.137154] PCI: bus1: Fast back to back transfers enabled [ 0.137250] PCI: bus2: Fast back to back transfers enabled [ 0.137281] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.137289] pci 0000:00:02.0: PCI bridge to [bus 02] [ 0.137297] PCI: enabling device 0000:00:01.0 (0140 -> 0143) [ 0.137303] PCI: enabling device 0000:00:02.0 (0140 -> 0143) [ 0.137848] SCSI subsystem initialized [ 0.139013] Switching to clocksource armada_370_xp_clocksource [ 0.139221] AppArmor: AppArmor Filesystem Enabled [ 0.140373] NET: Registered protocol family 2 [ 0.140760] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.140803] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.140842] TCP: Hash tables configured (established 4096 bind 4096) [ 0.140871] TCP: reno registered [ 0.140877] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.140891] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.140993] NET: Registered protocol family 1 [ 0.141109] Trying to unpack rootfs image as initramfs... [ 1.223952] Freeing initrd memory: 3444K [ 1.224186] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 1.225888] Initialise module verification [ 1.225931] audit: initializing netlink socket (disabled) [ 1.225963] type=2000 audit(1.210:1): initialized [ 1.227388] VFS: Disk quotas dquot_6.5.2 [ 1.227448] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.227641] msgmni has been set to 1000 [ 1.228279] Key type asymmetric registered [ 1.228285] Asymmetric key parser 'x509' registered [ 1.228487] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 1.228495] io scheduler noop registered [ 1.228499] io scheduler deadline registered [ 1.228516] io scheduler cfq registered (default) [ 1.229806] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.230430] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.269365] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 1.299365] mv_xor f1060800.xor: freeing 1 in use descriptors! [ 1.299376] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 1.299659] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.339347] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 1.369361] mv_xor f1060900.xor: freeing 1 in use descriptors! [ 1.369371] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 1.370213] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.392264] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A [ 2.087689] console [ttyS0] enabled [ 2.111731] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A [ 2.129352] brd: module loaded [ 2.132423] Loading iSCSI transport class v2.0-870. [ 2.140130] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 2.148963] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 2 SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 [ 8.659046] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 8.666010] ata1.00: ATA-9: ST1000DM010-2DM162, CC46, max UDMA/133 [ 8.672226] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.679047] ata1.00: SN: Z4YGV8EN [ 8.684115] ata1.00: configured for UDMA/133 [ 8.688994] scsi 0:0:0:0: Direct-Access ATA ST1000DM010-2DM162 CC46 PQ: 0 ANSI: 5 [ 8.698734] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 8.699451] Delay 5 seconds to wait for disk 2 ready. [ 8.711516] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 8.717108] sd 0:0:0:0: [sda] Write Protect is off [ 8.721983] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.755921] sda: sda1 sda2 sda3 < sda5 > [ 8.762237] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.059043] ata2: link is slow to respond, please be patient (ready=0) [ 25.619044] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 25.660044] ata2.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133 [ 25.666687] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 25.673508] ata2.00: SN: WD-WCAV5R907420 [ 25.680439] ata2.00: configured for UDMA/133 [ 25.686798] scsi 1:0:0:0: Direct-Access WDC WD10EARS-00Y5B1 80.0 PQ: 0 ANSI: 5 [ 25.696589] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 25.702469] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 25.702487] Searching for RedBoot partition table in spi0.0 at offset 0x7f0000 [ 25.716822] sd 1:0:0:0: [sdb] Write Protect is off [ 25.721698] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 25.750931] sdb: sdb1 sdb2 sdb3 < sdb5 > [ 25.757291] sd 1:0:0:0: [sdb] Attached SCSI disk [ 25.802729] 6 RedBoot partitions found on MTD device spi0.0 [ 25.808326] Creating 6 MTD partitions on "spi0.0": [ 25.813154] 0x000000000000-0x0000000f0000 : "RedBoot" [ 25.819526] 0x0000000f0000-0x0000003c0000 : "zImage" [ 25.825847] 0x0000003c0000-0x0000007d0000 : "rd.gz" [ 25.832087] 0x0000007d0000-0x0000007e0000 : "vendor" [ 25.837542] vender Mac0 address : 00:11:32:a3:6c:3e [ 25.842455] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 25.848310] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 25.854213] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 25.860076] serial number='1910Q2N424414' [ 25.865041] 0x0000007e0000-0x0000007f0000 : "RedBoot Config" [ 25.872146] 0x0000007f0000-0x000000800000 : "FIS directory" [ 25.882281] SoC: model = 0x6820, revision = 0x4 [ 25.886895] mvPncVirtBase = 0xa0c00000, pncTcamSize = 1024 [ 25.892419] o 3 Giga ports supported [ 25.896182] o SKB recycle supported for SWF (Disabled) [ 25.901535] o NETA acceleration mode 4 [ 25.905472] o BM supported for CPU: 4 BM pools [ 25.910110] o PnC supported (Enabled) [ 25.913960] o RX Queue support: 8 Queues * 512 Descriptors [ 25.919644] o TX Queue support: 8 Queues * 1024 Descriptors [ 25.925410] o GSO supported [ 25.928387] o GRO supported [ 25.931366] o Receive checksum offload supported [ 25.936174] o Transmit checksum offload supported [ 25.941071] o Driver ERROR statistics enabled [ 25.945617] o Driver INFO statistics enabled [ 25.950078] o Driver DEBUG statistics enabled [ 25.954624] [ 25.957167] port #0: is_sgmii=1, is_rgmii=0, phy_addr=1 [ 25.962453] o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 [ 25.970773] [ 25.972270] o Port 0 is connected to Linux netdevice [ 25.982129] o eth0, ifindex = 2, GbE port = 0 [ 25.986869] o eth0, phy chipid = 1410dd0, Support WOL = 32 [ 25.996156] giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) [ 26.002286] [ 26.004332] libphy: orion_mdio_bus: probed [ 26.010483] mdio_bus f1072004.mdio-mi: cannot get PHY at address 0 [ 26.018113] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 26.039229] i2c /dev entries driver [ 26.054616] armada_thermal f10e4078.thermal: Overheat threshold between 92..107 [ 26.062619] md: raid1 personality registered for level 1 [ 26.067957] cpuidle: using governor ladder [ 26.072380] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 [ 26.081753] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) [ 26.090375] mvCesaInit: channels=2, session=640, queue=256 [ 26.109225] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode [ 26.118862] cesadev_init(80560a18) [ 26.123110] TCP: cubic registered [ 26.126443] NET: Registered protocol family 17 [ 26.130945] Key type dns_resolver registered [ 26.135297] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 26.143026] Registering suspend init for this board failed [ 26.151588] Loading module verification blacklist certificates [ 26.157457] Loading module verification certificates [ 26.162558] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329' [ 26.177915] MODSIGN: Loaded cert 'Synology Root Certification Authority: f2c075361f168425f8b5ef31b796406c3aab2089' [ 26.188359] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certification Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28' [ 26.200273] MODSIGN: Loaded cert 'Synology kernel module signing key: 4646ce54489669338118a3b1286da156ac366fa5' [ 26.210418] registered taskstats version 1 [ 26.214568] regulator-dummy: disabling [ 26.218668] Freeing unused kernel memory: 220K START /linuxrc.syno START /linuxrc.syno.impl Insert basic USB modules... :: Loading module usb-common ... [ OK ] :: Loading module usbcore[ 26.429260] usbcore: registered new interface driver usbfs [ 26.437891] usbcore: registered new interface driver hub [ 26.448935] usbcore: registered new device driver usb ... [ OK ] :: Loading module ehci-hcd[ 26.486093] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ... [ OK ] :: Loading module xhci-hcd[ 26.518648] xhci-hcd f10f0000.usb3: USB2 Vbus gpio 58 [ 26.523803] xhci-hcd f10f0000.usb3: power control enabled [ 26.529255] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 26.534615] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 26.542337] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 [ 26.548820] hub 1-0:1.0: USB hub found [ 26.552659] hub 1-0:1.0: 1 port detected [ 26.556714] xhci-hcd f10f0000.usb3: USB3 Vbus gpio 58 [ 26.561829] xhci-hcd f10f0000.usb3: power control enabled [ 26.567260] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 26.572639] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 26.583352] hub 2-0:1.0: USB hub found [ 26.587148] hub 2-0:1.0: 1 port detected [ 26.591350] xhci-hcd f10f8000.usb3: USB2 Vbus gpio 59 [ 26.596433] xhci-hcd f10f8000.usb3: power control enabled [ 26.601893] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 26.607254] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 26.617075] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 [ 26.625875] hub 3-0:1.0: USB hub found [ 26.629744] hub 3-0:1.0: 1 port detected [ 26.633800] xhci-hcd f10f8000.usb3: USB3 Vbus gpio 59 [ 26.638882] xhci-hcd f10f8000.usb3: power control enabled [ 26.644362] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 26.649750] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 26.660430] hub 4-0:1.0: USB hub found [ 26.664222] hub 4-0:1.0: 1 port detected ... [ OK ] :: Loading module ehci-orion[ 26.734361] ehci-orion: EHCI orion driver [ 26.738575] orion-ehci f1058000.usb: failed to get Vbus gpio [ 26.744296] orion-ehci f1058000.usb: USB2 Vbus gpio -1 [ 26.749467] orion-ehci f1058000.usb: power control disabled [ 26.755063] orion-ehci f1058000.usb: EHCI Host Controller [ 26.760515] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 5 [ 26.768179] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 [ 26.789055] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 26.795711] hub 5-0:1.0: USB hub found [ 26.799535] hub 5-0:1.0: 1 port detected ... [ OK ] insmod: can't insert '/lib/modules/etxhci-hcd.ko': No such file or directory Insert net driver(Mindspeed only)...[ 26.859814] ds218j_synobios: module license 'Synology Inc.' taints kernel. [ 26.867490] Disabling lock debugging due to kernel taint [ 26.875993] synobios open /dev/ttyS1 success [ 26.880308] Synobios DS218j GPIO initialized [ 26.884857] 2023-1-2 21:20:5 UTC [ 26.888099] synobios: load, major number 201 [ 26.892420] Brand: Synology [ 26.895234] Model: DS-218j [ 26.897954] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 26.906473] synobios cpu_arch proc entry initialized [ 26.911469] synobios crypto_hw proc entry initialized [ 26.916543] synobios syno_platform proc entry initialized Starting /usr/syno/bin/synocfgen... /usr/syno/bin/synocfgen returns 0 [ 26.937208] Module [ds218j_synobios] is removed. [ 26.942045] synobios: unload Assemble args: -u 978a118b:a2d37830:3017a5a8:c86610be /dev/sda1 /dev/sdb1 [ 27.149639] md: md0 stopped. [ 27.154776] md: bind [ 27.159130] md: bind [ 27.162374] md/raid1:md0: active with 2 out of 2 mirrors [ 27.190229] md0: detected capacity change from 0 to 2549940224 [ 27.196969] md0: unknown partition table mdadm: /dev/md0 has been started with 2 drives. Partition Version=8 [ 27.343574] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 27.352767] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 27.404154] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) /sbin/e2fsck exists, checking /dev/md0... e2fsck 1.44.1 (24-Mar-2018) /sbin/e2fsck -yvf returns 0 Mounting /dev/md0 /tmpRoot [ 27.840564] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 27.849905] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 27.869461] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) ------------upgrade Begin upgrade procedure Failed to found any patch No upgrade file found ============upgrade ------------bootup-smallupdate Failed to AssertDirectory[/tmpRoot/etc.defaults/] Skip bootup smallupdate, because root is not matched to junior ============bootup-smallupdate Missing directory /etc. Copy from /etc.defaults... cp: can't stat '/tmpRoot/etc.defaults': No such file or directory Exit on error [255] prepare /etc failed... Mon Jan 2 21:20:07 UTC 2023 /dev/md0 /tmpRoot ext4 rw,relatime,journal_checksum,data=ordered 0 0 none /sys/kernel/debug debugfs rw,relatime 0 0 umount: /etc/mtab: No such file or directory linuxrc.syno failed on 255 starting pid 1271, tty '': '/etc/rc' :: Starting /etc/rc :: Mounting procfs ... [ OK ] :: Mounting tmpfs ... [ OK ] :: Mounting devtmpfs ... [ OK ] :: Mounting devpts ... [ OK ] :: Mounting sysfs ... [ OK ] [ 29.387000] md: md1 stopped. [ 29.392207] md: bind [ 29.396635] md: bind [ 29.399852] md/raid1:md1: active with 2 out of 2 mirrors [ 29.430869] md1: detected capacity change from 0 to 2147418112 [ 29.457461] md1: unknown partition table [ 29.516843] Adding 2097084k swap on /dev/md1. Priority:-1 extents:1 across:2097084k :: Loading module fat ... [ OK ] :: Loading module vfat ... [ OK ] :: Loading module sunrpc[ 29.867446] RPC: Registered named UNIX socket transport module. [ 29.873440] RPC: Registered udp transport module. [ 29.878167] RPC: Registered tcp transport module. [ 29.882913] RPC: Registered tcp NFSv4.1 backchannel transport module. ... [ OK ] :: Loading module lockd ... [ OK ] :: Loading module nfs ... [ OK ] :: Loading module nfsv3 ... [ OK ] [ 29.993759] synobios open /dev/ttyS1 success [ 29.998058] Synobios DS218j GPIO initialized [ 30.002656] 2023-1-2 21:20:8 UTC [ 30.005900] synobios: load, major number 201 [ 30.010205] Brand: Synology [ 30.013010] Model: DS-218j [ 30.015724] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 30.024227] synobios cpu_arch proc entry initialized [ 30.029219] synobios crypto_hw proc entry initialized [ 30.034292] synobios syno_platform proc entry initialized mknod: /dev/synobios: File exists Starting SW init... [ 30.360031] Module [ds218j_synobios] is removed. [ 30.364791] synobios: unload :: Loading module synobios[ 30.442934] synobios open /dev/ttyS1 success [ 30.447234] Synobios DS218j GPIO initialized [ 30.451820] 2023-1-2 21:20:8 UTC [ 30.455065] synobios: load, major number 201 [ 30.459368] Brand: Synology [ 30.462173] Model: DS-218j [ 30.464888] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 30.473386] synobios cpu_arch proc entry initialized [ 30.478371] synobios crypto_hw proc entry initialized [ 30.483451] synobios syno_platform proc entry initialized ... [ OK ] [ 30.644103] eth0: mac address changed [ 30.745700] pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added [ 30.753289] eth0: link up [ 30.755990] eth0: started [ 30.756006] eth0: [ 30.756008] link up [ 30.756008] , full duplex [ 30.756009] , speed [ 30.756009] 100 Mbps udhcpc: started, v1.30.1 eth0 Link encap:Ethernet HWaddr 00:11:32:A3:6C:3E inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1024 RX bytes:689 (689.0 B) TX bytes:989 (989.0 B) Interrupt:193 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) :: Starting syslogd ... [ OK ] /etc/rc: line 302: /usr/syno/bin/syno_pstore_collect: not found :: Starting scemd [ 38.585829] eth0: [ 38.587677] link up, full duplex [ 38.590943] , speed [ 38.593146] 100 Mbps :: Starting services in background Starting JuniorExpansionPack Starting findhostd in flash_rd... Starting services in flash_rd... Running /usr/syno/etc/rc.d/J01httpd.sh... Starting httpd:80 in flash_rd... Starting httpd:5000 in flash_rd... Running /usr/syno/etc/rc.d/J03ssdpd.sh... /usr/bin/minissdpd -i eth0 [ 38.713070] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 38.722419] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) (15): upnp:rootdevice (51): uuid:upnp_SynologyNAS-001132a36c3e::upnp:rootdevice[ 38.767318] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) (58): Synology/synology_armada38x_ds218j/7.1-42962/192.168.1.102 (46): http://192.168.1.102:5000/description-eth0.xml Connected. done. /usr/syno/bin/reg_ssdp_service 192.168.1.102 001132a36c3e 7.1-42962 synology_armada38x_ds218j eth0 Running /usr/syno/etc/rc.d/J04synoagentregisterd.sh... Starting synoagentregisterd... Running /usr/syno/etc/rc.d/J30DisableNCQ.sh... Running /usr/syno/etc/rc.d/J80ADTFanControl.sh... Running /usr/syno/etc/rc.d/J98nbnsd.sh... Starting nbnsd... Running /usr/syno/etc/rc.d/J99avahi.sh... Starting Avahi mDNS/DNS-SD Daemon /usr/syno/sbin/avahi-daemon: error while loading shared libraries: libm.so.6: cannot open shared object file: No such file or[ 39.031606] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) directory [ 39.041630] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 39.059963] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 39.117248] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 39.126565] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) :: Loading module usb-storage[ 39.172373] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 39.181265] usbcore: registered new interface driver usb-storage ... [ OK ] Excution Error ============ Date ============ Mon Jan 2 21:20:16 UTC 2023 ============================== starting pid 2385, tty '': '/sbin/getty 115200 console' Mon Jan 2 21:20:16 2023 DiskStation login: [ 41.825710] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 41.834805] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 41.884291] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 42.114878] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 42.123899] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 42.139548] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 42.164992] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 42.174075] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 42.193469] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 73.322976] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 73.516022] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 73.554953] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 164.855903] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 164.864936] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 164.915267] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 207.166618] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 207.175645] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 207.220426] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 210.160952] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 210.170030] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 210.220802] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 211.420955] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.429967] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.479290] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 211.701896] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.710921] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.729436] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 211.755870] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.764946] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.780292] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 211.851385] EXT3-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.860623] EXT2-fs (md0): error: couldn't mount because of unsupported optional features (240) [ 211.879448] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)