NSA310> boot resetting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found 6075028 bytes read in 851 ms (6.8 MiB/s) 10295205 bytes read in 1137 ms (8.6 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-6.2.7-kirkwood-tld-1 Created: 2023-04-10 2:51:11 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6074964 Bytes = 5.8 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02100000 ... Image Name: initramfs-6.2.7-kirkwood-tld-1 Created: 2023-04-10 2:52:09 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 10295141 Bytes = 9.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Loading Ramdisk to 0f13c000, end 0fb0d765 ... OK Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.2.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 PREEMPT Tue Mar 21 18:52:10 PDT 2023 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: ZyXEL NSA310 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 229028K/262144K available (11264K kernel code, 1689K rwdata, 5216K rodata, 1024K init, 310K bss, 33116K reserved, 0K cma-reserved) [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008609][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.017241][ T0] Console: colour dummy device 80x30 [ 0.022522][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.033867][ T0] pid_max: default: 32768 minimum: 301 [ 0.040016][ T0] LSM: initializing lsm=capability,integrity [ 0.046371][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054501][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.065473][ T0] CPU: Testing write buffer coherency: ok [ 0.074345][ T1] cblist_init_generic: Setting adjustable number of callback queues. [ 0.082421][ T1] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.089668][ T1] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.097005][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.104327][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.110650][ T1] rcu: Hierarchical SRCU implementation. [ 0.116187][ T1] rcu: Max phase no-delay instances is 1000. [ 0.124187][ T1] devtmpfs: initialized [ 0.137501][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.148229][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.156394][ T1] prandom: seed boundary self test passed [ 0.166303][ T1] prandom: 100 self tests passed [ 0.171183][ T1] pinctrl core: initialized pinctrl subsystem [ 0.180155][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.187621][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.196792][ T1] audit: initializing netlink subsys (disabled) [ 0.205073][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.205499][ T16] audit: type=2000 audit(0.190:1): state=initialized audit_enabled=0 res=1 [ 0.220957][ T1] cpuidle: using governor ladder [ 0.225885][ T1] cpuidle: using governor menu [ 0.231205][ T1] Feroceon L2: Enabling L2 [ 0.235541][ T1] Feroceon L2: Cache support initialised. [ 0.252305][ T1] No ATAGs? [ 0.618630][ T1] raid6: int32x8 gen() 108 MB/s [ 0.958628][ T1] raid6: int32x4 gen() 96 MB/s [ 1.298654][ T1] raid6: int32x2 gen() 136 MB/s [ 1.638627][ T1] raid6: int32x1 gen() 97 MB/s [ 1.643632][ T1] raid6: using algorithm int32x2 gen() 136 MB/s [ 1.998627][ T1] raid6: .... xor() 85 MB/s, rmw enabled [ 2.004152][ T1] raid6: using intx1 recovery algorithm [ 2.019833][ T1] SCSI subsystem initialized [ 2.029206][ T1] usbcore: registered new interface driver usbfs [ 2.035483][ T1] usbcore: registered new interface driver hub [ 2.058693][ T1] usbcore: registered new device driver usb [ 2.064874][ T1] pps_core: LinuxPPS API ver. 1 registered [ 2.078629][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.088539][ T1] PTP clock support registered [ 2.111116][ T1] vgaarb: loaded [ 2.119262][ T1] clocksource: Switched to clocksource orion_clocksource [ 2.140372][ T1] VFS: Disk quotas dquot_6.6.0 [ 2.145115][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.190349][ T1] NET: Registered PF_INET protocol family [ 2.199394][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 2.220073][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 2.239489][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 2.247998][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 2.279322][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 2.287245][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 2.309650][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 2.317704][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 2.339339][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 2.347386][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 2.370217][ T1] RPC: Registered named UNIX socket transport module. [ 2.376880][ T1] RPC: Registered udp transport module. [ 2.389289][ T1] RPC: Registered tcp transport module. [ 2.394720][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.419297][ T1] PCI: CLS 0 bytes, default 32 [ 2.424347][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.432116][ T19] Trying to unpack rootfs image as initramfs... [ 4.356734][ T19] Freeing initrd memory: 10056K [ 4.526351][ T1] Initialise system trusted keyrings [ 4.532641][ T1] Key type blacklist registered [ 4.537784][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 4.545281][ T1] zbud: loaded [ 4.551359][ T1] NFS: Registering the id_resolver key type [ 4.557202][ T1] Key type id_resolver registered [ 4.562193][ T1] Key type id_legacy registered [ 4.566999][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.574481][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 4.583169][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 4.591557][ T1] fuse: init (API version 7.38) [ 4.596825][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 4.604331][ T1] orangefs_init: module version upstream loaded [ 4.610498][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 4.716106][ T1] xor: measuring software checksum speed [ 4.730488][ T1] arm4regs : 1118 MB/sec [ 4.750260][ T1] 8regs : 671 MB/sec [ 4.765693][ T1] 32regs : 952 MB/sec [ 4.770790][ T1] xor: using function: arm4regs (1118 MB/sec) [ 4.776754][ T1] async_tx: api initialized (async) [ 4.781859][ T1] Key type asymmetric registered [ 4.786678][ T1] Asymmetric key parser 'x509' registered [ 4.836244][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 4.844819][ T1] io scheduler bfq registered [ 5.040981][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 5.050174][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 5.061137][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 5.071814][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 5.081874][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 5.092137][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 5.102890][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 5.114388][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 5.122749][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 5.128978][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 5.139934][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 5.147548][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 5.154684][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 5.163087][ T1] PCI: bus0: Fast back to back transfers disabled [ 5.169445][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 5.178533][ T1] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 5.185324][ T1] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 5.191683][ T1] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit pref] [ 5.199681][ T1] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 5.207651][ T1] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 5.215221][ T1] pci 0000:01:00.0: supports D1 D2 [ 5.220242][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 5.249380][ T1] PCI: bus1: Fast back to back transfers disabled [ 5.255701][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 5.263125][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 5.270770][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 5.277878][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 5.285872][ T1] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 5.294397][ T1] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 5.302922][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 5.309957][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 5.315653][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 5.322685][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 5.330386][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 5.337920][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 5.400682][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 5.413122][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 5.480664][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 5.493449][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.502573][ T1] printk: console [ttyS0] disabled [ 5.507660][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A [ 5.517528][ T1] printk: console [ttyS0] enabled [ 5.517528][ T1] printk: console [ttyS0] enabled [ 5.527410][ T1] printk: bootconsole [earlycon0] disabled [ 5.527410][ T1] printk: bootconsole [earlycon0] disabled [ 5.571728][ T1] loop: module loaded [ 5.576761][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 5.586976][ T1] scsi host0: sata_mv [ 5.591951][ T1] scsi host1: sata_mv [ 5.596222][ T1] ata1: SATA max UDMA/133 irq 29 [ 5.601116][ T1] ata2: SATA max UDMA/133 irq 29 [ 5.607189][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 5.614324][ T1] nand: Samsung NAND 128MiB 3,3V 8-bit [ 5.619692][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 5.628036][ T1] Scanning device for bad blocks [ 5.669216][ T1] Bad eraseblock 376 at 0x000002f00000 [ 5.710890][ T1] Bad eraseblock 753 at 0x000005e20000 [ 5.742390][ T1] 9 fixed-partitions partitions found on MTD device orion_nand [ 5.749851][ T1] Creating 9 MTD partitions on "orion_nand": [ 5.755776][ T1] 0x000000000000-0x000000100000 : "uboot" [ 5.762168][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 5.768851][ T1] 0x000000180000-0x000000200000 : "key_store" [ 5.775562][ T1] 0x000000200000-0x000000280000 : "info" [ 5.781852][ T1] 0x000000280000-0x000000c80000 : "etc" [ 5.787974][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 5.794630][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 5.801404][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 5.808057][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 5.815335][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.823994][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 5.837926][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 5.844266][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 5.852975][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 5.889290][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 5.896453][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.02 [ 5.905526][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.913567][ T1] usb usb1: Product: EHCI Host Controller [ 5.919204][ T1] usb usb1: Manufacturer: Linux 6.2.7-kirkwood-tld-1 ehci_hcd [ 5.926600][ T1] usb usb1: SerialNumber: f1050000.ehci [ 5.932078][ T50] ata1: SATA link down (SStatus 0 SControl F300) [ 5.939455][ T1] hub 1-0:1.0: USB hub found [ 5.943997][ T1] hub 1-0:1.0: 1 port detected [ 5.949826][ T1] usbcore: registered new interface driver usb-storage [ 5.957294][ T1] mousedev: PS/2 mouse device common for all mice [ 5.965223][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 5.971084][ T1] rtc-mv f1010300.rtc: setting system clock to 2023-04-10T02:55:38 UTC (1681095338) [ 5.980602][ T1] i2c_dev: i2c /dev entries driver [ 5.987909][ T1] device-mapper: uevent: version 1.0.3 [ 5.993727][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 6.003669][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 6.011024][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 6.018381][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 6.025861][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 6.032719][ T1] device-mapper: raid: Loading target version 1.15.1 [ 6.042386][ T1] hid: raw HID events driver (C) Jiri Kosina [ 6.048710][ T1] drop_monitor: Initializing network drop monitor service [ 6.056403][ T1] NET: Registered PF_INET6 protocol family [ 6.064105][ T1] Segment Routing with IPv6 [ 6.068502][ T1] RPL Segment Routing with IPv6 [ 6.073436][ T1] In-situ OAM (IOAM) with IPv6 [ 6.078204][ T1] NET: Registered PF_PACKET protocol family [ 6.084603][ T1] Key type dns_resolver registered [ 6.105906][ T1] registered taskstats version 1 [ 6.110987][ T1] Loading compiled-in X.509 certificates [ 6.117728][ T1] zswap: loaded using pool lzo/zbud [ 6.123747][ T1] Key type .fscrypt registered [ 6.128401][ T1] Key type fscrypt-provisioning registered [ 6.140293][ T1] Key type big_key registered [ 6.182958][ T1] Key type encrypted registered [ 6.229375][ T47] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 6.282839][ T52] ata2: SATA link down (SStatus 0 SControl F300) [ 6.298768][ T101] "cryptomgr_test" (101) uses obsolete ecb(arc4) skcipher [ 6.441107][ T47] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 6.459284][ T47] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 6.467163][ T47] usb 1-1: Product: USB2.0 Hub [ 6.490483][ T47] hub 1-1:1.0: USB hub found [ 6.499295][ T47] hub 1-1:1.0: 4 ports detected [ 6.829291][ T47] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 7.290604][ T47] usb 1-1.3: New USB device found, idVendor=13fe, idProduct=5000, bcdDevice= 1.10 [ 7.309309][ T47] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.317363][ T47] usb 1-1.3: Product: MKNUFDVP32GB [ 7.333984][ T47] usb 1-1.3: Manufacturer: MUSHKIN [ 7.338990][ T47] usb 1-1.3: SerialNumber: 07072672BAF71704 [ 7.360344][ T47] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 7.379876][ T47] scsi host2: usb-storage 1-1.3:1.0 [ 8.410195][ T8] scsi 2:0:0:0: Direct-Access MUSHKIN MKNUFDVP32GB PMAP PQ: 0 ANSI: 4 [ 8.431398][ T28] sd 2:0:0:0: [sda] 61767680 512-byte logical blocks: (31.6 GB/29.5 GiB) [ 8.449768][ T28] sd 2:0:0:0: [sda] Write Protect is off [ 8.459352][ T28] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.705878][ T28] sda: sda1 sda2 [ 8.710491][ T28] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 8.720220][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 8.740116][ T1] Checked W+X mappings: passed, no W+X pages found [ 8.746551][ T1] Run /init as init process Loading, please wait... Starting version 247.3-6 [ 9.756013][ T143] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 9.954444][ T143] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 10.050875][ T143] r8169 0000:01:00.0 eth0: RTL8168d/8111d, 00:00:00:00:00:30, XID 283, IRQ 36 [ 10.082731][ T148] usbcore: registered new interface driver uas [ 10.096980][ T143] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] [ 10.154731][ T138] regulator@1 enforce active low on GPIO handle [ 10.708332][ T143] r8169 0000:01:00.0 enp1s0: renamed from eth0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: clean, 18713/256000 files, 271642/1024000 blocks done. [ 21.067177][ T169] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.148283][ T169] EXT4-fs (sda1): mounted filesystem 56f958f2-a1c6-46bf-8f70-86789254af6f with ordered data mode. Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 24.658470][ T353] orion_wdt: Initial timeout 21 sec [ 24.853183][ T350] hwmon_vid: Unknown VRM version of your CPU [ 25.006173][ T350] lm85 0-002e: Starting monitoring [ 25.200709][ T350] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 25.279385][ T358] marvell-cesa f1030000.crypto: CESA device successfully registered done. Activating swap:. [ 26.612091][ T507] EXT4-fs (sda1): re-mounted 56f958f2-a1c6-46bf-8f70-86789254af6f. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. [ 28.022538][ T116] random: crng init done Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. Initializing random number generator...done. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Cannot find device "eth0" Failed to get interface index: No such device If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging. exiting. ifup: failed to bring up eth0 failed. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1035 (syslogd) . Starting NFS common utilities: statd idmapd. Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Not starting NFS kernel daemon: no exports. ... (warning). Starting NTP server: ntpd. Starting OpenBSD Secure Shell server: sshd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1075 (klogd) . Running local boot scripts (/etc/rc.local) . Debian GNU/Linux 11 debian ttyS0 debian login: