U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:42:03 -0700) ZyXEL NSA325 2-Bay Power Media Server SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 No link on egiga0 ping failed; host 192.168.16.206 is not alive No link on egiga0 ping failed; host 192.168.16.206 is not alive No link on egiga0 ping failed; host 192.168.16.206 is not alive No link on egiga0 ping failed; host 192.168.16.206 is not alive No link on egiga0 ping failed; host 192.168.16.206 is not alive Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: ST4000VN008-2DR166 Firm: SC60 Ser#: ZM402JC2 Type: Hard Disk Supports 48-bit addressing Capacity: 3815447.8 MB = 3726.0 GB (7814037168 x 512) Device 1: Model: ST4000NE0025-2EW107 Firm: EN02 Ser#: ZC13J8MJ Type: Hard Disk Supports 48-bit addressing Capacity: 3815447.8 MB = 3726.0 GB (7814037168 x 512) Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15353856 1e2e9c52-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Partition Map for IDE device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000f3fff "mitraswap" attrs: 0x0000000000000000 type: 0657fd6d-a4ab-43c4-84e5-0933c84b4f4f type: swap guid: 95514482-ae94-48c9-bf66-b21542868d6b 2 0x000f4000 0x1d1c0b7ff "eexxtt44" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: 0770c9e5-d7b2-4f0e-bd40-ed152aecc996 Partition Map for IDE device 1 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000f3fff "mitraswap" attrs: 0x0000000000000000 type: 0657fd6d-a4ab-43c4-84e5-0933c84b4f4f type: swap guid: 819cfccc-2d0d-4afa-987e-eab840da5a4c 2 0x000f4000 0x1d1c0b7ff "eexxtt44" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: 65797280-5d61-41ee-b2b6-9fb35c885329 Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 723 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5435888 bytes read in 1170 ms (4.4 MiB/s) loading uInitrd ... 9671091 bytes read in 1259 ms (7.3 MiB/s) loading DTB /boot/dts/kirkwood-nsa325.dtb ... 14014 bytes read in 1646 ms (7.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.13.6-kirkwood-tld-1 Created: 2021-09-24 0:22:58 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5435824 Bytes = 5.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.13.6-kirkwood-tld-1 Created: 2021-09-24 1:06:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9671027 Bytes = 9.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 1f1d4000, end 1fb0d173 ... OK Loading Device Tree to 1f1cd000, end 1f1d36bd ... OK Using machid 0x831 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: ZyXEL NSA325 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 490944K/524288K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 33344K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000050][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000764][ T0] Console: colour dummy device 80x30 [ 0.000827][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000862][ T0] pid_max: default: 32768 minimum: 301 [ 0.001195][ T0] LSM: Security Framework initializing [ 0.001344][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001385][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002575][ T0] CPU: Testing write buffer coherency: ok [ 0.004606][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.004879][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.005171][ T1] rcu: Hierarchical SRCU implementation. [ 0.006374][ T1] devtmpfs: initialized [ 0.012344][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.012391][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.040407][ T1] prandom32: self test passed (less than 6 bits correlated) [ 0.040445][ T1] prandom: seed boundary self test passed [ 0.043586][ T1] prandom: 100 self tests passed [ 0.043601][ T1] pinctrl core: initialized pinctrl subsystem [ 0.044986][ T1] NET: Registered protocol family 16 [ 0.045604][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.046385][ T1] audit: initializing netlink subsys (disabled) [ 0.047574][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.047895][ T16] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1 [ 0.048052][ T1] cpuidle: using governor ladder [ 0.048136][ T1] cpuidle: using governor menu [ 0.048558][ T1] Feroceon L2: Enabling L2 [ 0.048599][ T1] Feroceon L2: Cache support initialised. [ 0.056965][ T1] No ATAGs? [ 2.560054][ C0] random: fast init done [ 3.683005][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher [ 3.701712][ T59] wait_for_initramfs() called before rootfs_initcalls [ 3.890248][ T1] raid6: int32x8 gen() 151 MB/s [ 4.060117][ T1] raid6: int32x8 xor() 93 MB/s [ 4.230174][ T1] raid6: int32x4 gen() 153 MB/s [ 4.400146][ T1] raid6: int32x4 xor() 98 MB/s [ 4.570064][ T1] raid6: int32x2 gen() 198 MB/s [ 4.740093][ T1] raid6: int32x2 xor() 121 MB/s [ 4.910092][ T1] raid6: int32x1 gen() 151 MB/s [ 5.080153][ T1] raid6: int32x1 xor() 86 MB/s [ 5.080166][ T1] raid6: using algorithm int32x2 gen() 198 MB/s [ 5.080176][ T1] raid6: .... xor() 121 MB/s, rmw enabled [ 5.080185][ T1] raid6: using intx1 recovery algorithm [ 5.080399][ T1] vgaarb: loaded [ 5.080849][ T1] SCSI subsystem initialized [ 5.081259][ T1] usbcore: registered new interface driver usbfs [ 5.081313][ T1] usbcore: registered new interface driver hub [ 5.081357][ T1] usbcore: registered new device driver usb [ 5.081518][ T1] pps_core: LinuxPPS API ver. 1 registered [ 5.081531][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 5.081557][ T1] PTP clock support registered [ 5.082982][ T1] clocksource: Switched to clocksource orion_clocksource [ 5.163497][ T1] VFS: Disk quotas dquot_6.6.0 [ 5.163590][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.171456][ T1] NET: Registered protocol family 2 [ 5.171621][ T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 5.172644][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 5.172694][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 5.172763][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 5.172821][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 5.173049][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 5.173116][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 5.173149][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 5.173341][ T1] NET: Registered protocol family 1 [ 5.183463][ T1] RPC: Registered named UNIX socket transport module. [ 5.183482][ T1] RPC: Registered udp transport module. [ 5.183491][ T1] RPC: Registered tcp transport module. [ 5.183500][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.183515][ T1] PCI: CLS 0 bytes, default 32 [ 5.183766][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 5.185080][ T58] Trying to unpack rootfs image as initramfs... [ 6.457126][ T58] Freeing initrd memory: 9448K [ 6.926301][ T1] Initialise system trusted keyrings [ 6.926357][ T1] Key type blacklist registered [ 6.926574][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 6.926673][ T1] zbud: loaded [ 6.927815][ T1] NFS: Registering the id_resolver key type [ 6.927850][ T1] Key type id_resolver registered [ 6.927861][ T1] Key type id_legacy registered [ 6.927896][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.927916][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.927927][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.928154][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 6.928532][ T1] fuse: init (API version 7.34) [ 6.928876][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.929040][ T1] orangefs_init: module version upstream loaded [ 6.929055][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 7.004306][ T1] xor: measuring software checksum speed [ 7.010929][ T1] arm4regs : 1493 MB/sec [ 7.021974][ T1] 8regs : 895 MB/sec [ 7.029559][ T1] 32regs : 1302 MB/sec [ 7.029572][ T1] xor: using function: arm4regs (1493 MB/sec) [ 7.029591][ T1] async_tx: api initialized (async) [ 7.029607][ T1] Key type asymmetric registered [ 7.029617][ T1] Asymmetric key parser 'x509' registered [ 7.029666][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 7.029734][ T1] io scheduler bfq registered [ 7.178691][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 7.180195][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 7.180264][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 7.180299][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000 [ 7.180332][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000 [ 7.180364][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 7.180396][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 7.180427][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 7.180451][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 7.180699][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 7.180717][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 7.180736][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 7.180754][ T1] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff]) [ 7.180772][ T1] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff]) [ 7.180788][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 7.180802][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 7.180915][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 7.180945][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 7.182102][ T1] PCI: bus0: Fast back to back transfers disabled [ 7.182130][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 7.182307][ T1] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330 [ 7.182347][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 7.182496][ T1] pci 0000:01:00.0: PME# supported from D0 D3hot [ 7.182572][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 7.203998][ T1] PCI: bus1: Fast back to back transfers disabled [ 7.204024][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 7.204197][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 7.204221][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 7.204242][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] [ 7.204269][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 7.204286][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 7.204386][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 7.204465][ T1] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 7.204931][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 7.263825][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 7.265818][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 7.323824][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 7.326069][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 7.327210][ T1] printk: console [ttyS0] disabled [ 7.327290][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 8.461051][ T1] printk: console [ttyS0] enabled [ 8.472577][ T1] loop: module loaded [ 8.477176][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 8.485733][ T1] scsi host0: sata_mv [ 8.490097][ T1] scsi host1: sata_mv [ 8.494195][ T1] ata1: SATA max UDMA/133 irq 32 [ 8.499015][ T1] ata2: SATA max UDMA/133 irq 32 [ 8.504620][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 8.511749][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 8.516762][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 8.525302][ T1] Scanning device for bad blocks [ 8.535371][ T1] Bad eraseblock 100 at 0x000000c80000 [ 8.545896][ T1] Bad eraseblock 200 at 0x000001900000 [ 8.593836][ T1] 9 cmdlinepart partitions found on MTD device orion_nand [ 8.600837][ T1] Creating 9 MTD partitions on "orion_nand": [ 8.606714][ T1] 0x000000000000-0x000000100000 : "uboot" [ 8.613539][ T1] 0x000000100000-0x000000180000 : "stock_uboot_env" [ 8.621069][ T1] 0x000000180000-0x000000200000 : "key_store" [ 8.628118][ T1] 0x000000200000-0x000000280000 : "info" [ 8.634703][ T1] 0x000000280000-0x000000c80000 : "etc" [ 8.641226][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 8.648233][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 8.655248][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 8.662209][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 8.669662][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 8.678268][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 8.689527][ T1] libphy: Fixed MDIO Bus: probed [ 8.695515][ T1] libphy: orion_mdio_bus: probed [ 8.713103][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 8.721893][ T1] mv643xx_eth: Set the PHY to fix link down [ 8.722435][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 5c:f4:ab:e7:ca:95 [ 8.737874][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.745257][ T1] ehci-pci: EHCI PCI platform driver [ 8.750503][ T1] ehci-orion: EHCI orion driver [ 8.755432][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 8.761693][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 8.770278][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 8.802999][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.810003][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 8.819049][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.827056][ T1] usb usb1: Product: EHCI Host Controller [ 8.832680][ T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd [ 8.840141][ T1] usb usb1: SerialNumber: f1050000.ehci [ 8.846167][ T1] hub 1-0:1.0: USB hub found [ 8.850670][ T1] hub 1-0:1.0: 1 port detected [ 8.856033][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 8.862000][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 8.870469][ T1] xhci_hcd 0000:01:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 8.880731][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 8.889851][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.897823][ T1] usb usb2: Product: xHCI Host Controller [ 8.903434][ T1] usb usb2: Manufacturer: Linux 5.13.6-kirkwood-tld-1 xhci-hcd [ 8.910868][ T1] usb usb2: SerialNumber: 0000:01:00.0 [ 8.916723][ T1] hub 2-0:1.0: USB hub found [ 8.921237][ T1] hub 2-0:1.0: 2 ports detected [ 8.926534][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 8.932495][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 8.940678][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 8.947800][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 8.956869][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 8.965891][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.973858][ T1] usb usb3: Product: xHCI Host Controller [ 8.979459][ T1] usb usb3: Manufacturer: Linux 5.13.6-kirkwood-tld-1 xhci-hcd [ 8.986902][ T1] usb usb3: SerialNumber: 0000:01:00.0 [ 8.992737][ T1] hub 3-0:1.0: USB hub found [ 8.997375][ T1] hub 3-0:1.0: 2 ports detected [ 9.002832][ T1] usbcore: registered new interface driver usb-storage [ 9.009977][ T1] mousedev: PS/2 mouse device common for all mice [ 9.016331][ T94] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.023804][ T1] i2c /dev entries driver [ 9.034798][ T1] rtc-pcf8563 0-0051: registered as rtc0 [ 9.041543][ T1] rtc-pcf8563 0-0051: setting system clock to 2022-02-02T23:08:57 UTC (1643843337) [ 9.052295][ T1] device-mapper: uevent: version 1.0.3 [ 9.058216][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 9.067551][ T94] ata1.00: ATA-10: ST4000VN008-2DR166, SC60, max UDMA/133 [ 9.075325][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 9.082593][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 9.089981][ T94] ata1.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 9.097683][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 9.105264][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 9.112300][ T1] device-mapper: raid: Loading target version 1.15.1 [ 9.118933][ T94] ata1.00: configured for UDMA/133 [ 9.126040][ T1] hid: raw HID events driver (C) Jiri Kosina [ 9.132449][ T1] drop_monitor: Initializing network drop monitor service [ 9.139841][ T1] NET: Registered protocol family 10 [ 9.145254][ T17] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 9.152880][ T7] scsi 0:0:0:0: Direct-Access ATA ST4000VN008-2DR1 SC60 PQ: 0 ANSI: 5 [ 9.163013][ T1] Segment Routing with IPv6 [ 9.167401][ T1] RPL Segment Routing with IPv6 [ 9.172227][ T1] NET: Registered protocol family 17 [ 9.178455][ T80] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB) [ 9.187387][ T80] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 9.193623][ T1] Key type dns_resolver registered [ 9.199043][ T80] sd 0:0:0:0: [sda] Write Protect is off [ 9.204690][ T1] registered taskstats version 1 [ 9.209515][ T1] Loading compiled-in X.509 certificates [ 9.215202][ T80] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.225025][ T100] usb 2-1: new high-speed USB device number 2 using xhci_hcd [ 9.232676][ T1] zswap: loaded using pool lzo/zbud [ 9.239125][ T1] Key type ._fscrypt registered [ 9.243911][ T1] Key type .fscrypt registered [ 9.248549][ T1] Key type fscrypt-provisioning registered [ 9.255886][ T1] Key type big_key registered [ 9.284705][ T1] Key type encrypted registered [ 9.302239][ T80] sda: sda1 sda2 [ 9.307270][ T80] sd 0:0:0:0: [sda] Attached SCSI disk [ 9.374659][ T17] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 9.383610][ T17] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 9.391493][ T17] usb 1-1: Product: USB2.0 Hub [ 9.396948][ T17] hub 1-1:1.0: USB hub found [ 9.401782][ T17] hub 1-1:1.0: 4 ports detected [ 9.445355][ T100] usb 2-1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 2.00 [ 9.454315][ T100] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.462203][ T100] usb 2-1: Product: DataTraveler 2.0 [ 9.467397][ T100] usb 2-1: Manufacturer: Kingston [ 9.472298][ T100] usb 2-1: SerialNumber: 50E549C342E8108029100190 [ 9.481389][ T100] usb-storage 2-1:1.0: USB Mass Storage device detected [ 9.488695][ T100] scsi host2: usb-storage 2-1:1.0 [ 9.693011][ T96] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.723007][ T100] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 9.730757][ T96] ata2.00: ATA-10: ST4000NE0025-2EW107, EN02, max UDMA/133 [ 9.737912][ T96] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 9.749995][ T96] ata2.00: configured for UDMA/133 [ 9.765456][ T58] scsi 1:0:0:0: Direct-Access ATA ST4000NE0025-2EW EN02 PQ: 0 ANSI: 5 [ 9.775348][ T80] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB) [ 9.784154][ T80] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 9.790169][ T80] sd 1:0:0:0: [sdb] Write Protect is off [ 9.795839][ T80] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.837745][ T80] sdb: sdb1 sdb2 [ 9.842677][ T80] sd 1:0:0:0: [sdb] Attached SCSI disk [ 9.851323][ T1] Freeing unused kernel memory: 1024K [ 9.863709][ T1] Checked W+X mappings: passed, no W+X pages found [ 9.870129][ T1] Run /init as init process [ 9.886888][ T100] usb 1-1.2: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 1.00 [ 9.899517][ T100] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.911675][ T100] usb 1-1.2: Product: DataTraveler 2.0 [ 9.921309][ T100] usb 1-1.2: Manufacturer: Kingston [ 9.930562][ T100] usb 1-1.2: SerialNumber: 1C6F65342F78BE30A9372A7E Loading, please [ 9.943318][ T100] usb-storage 1-1.2:1.0: USB Mass Storage device detected wait... [ 9.958747][ T100] scsi host3: usb-storage 1-1.2:1.0 Starting version 247.3-6 [ 10.565349][ T80] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 0000 PQ: 0 ANSI: 4 [ 10.591588][ T58] sd 2:0:0:0: [sdc] 30535744 512-byte logical blocks: (15.6 GB/14.6 GiB) [ 10.618497][ T143] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 10.627859][ T58] sd 2:0:0:0: [sdc] Write Protect is off [ 10.644975][ T58] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 10.684907][ T58] sdc: sdc1 sdc2 [ 10.699680][ T58] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 10.799340][ T143] usbcore: registered new interface driver uas [ 11.045521][ T58] scsi 3:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 4 [ 11.465328][ T80] sd 3:0:0:0: [sdd] 15356160 512-byte logical blocks: (7.86 GB/7.32 GiB) [ 11.475819][ T80] sd 3:0:0:0: [sdd] Write Protect is off [ 11.482059][ T80] sd 3:0:0:0: [sdd] No Caching mode page found [ 11.489101][ T80] sd 3:0:0:0: [sdd] Assuming drive cache: write through [ 11.503444][ T80] sdd: sdd1 [ 11.513955][ T80] sd 3:0:0:0: [sdd] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext3 (1) -- /dev/sdd1] fsck.ext3 -a -C0 /dev/sdd1 rootfs: clean, 22556/480496 files, 280665/1919232 blocks done. [ 22.110210][ T173] EXT4-fs (sdd1): mounting ext3 file system using the ext4 subsystem [ 22.245296][ T173] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. [ 23.672739][ C0] random: crng init done Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 25.111485][ T364] orion_wdt: Initial timeout 21 sec [ 25.270399][ T361] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 25.313728][ T361] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 25.393128][ T361] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 25.495850][ T361] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 25.544402][ T357] marvell-cesa f1030000.crypto: CESA device successfully registered [ 26.036072][ T411] md/raid1:md0: active with 2 out of 2 mirrors [ 26.090433][ T411] md0: detected capacity change from 0 to 7813033712 done. Activating swap:. [ 27.195600][ T522] EXT4-fs (sdd1): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. [ 29.209829][ T773] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Initializing random number generator...done. Starting Setting kernel variables: sysctl. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/5c:f4:ab:e7:ca:95 Sending on LPF/eth0/5c:f4:ab:e7:ca:95 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 17 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix . INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1086 (syslogd) . Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1118 (klogd) . Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting MD monitoring service: mdadm --monitor. Starting NFS common utilities: statd idmapd. Not starting NFS kernel daemon: no exports. ... (warning). Starting DLNA/UPnP-AV media server: minidlna. Starting NetBIOS name server: nmbd . Starting NTP server: ntpd. Starting SMB/CIFS daemon: smbd. Starting OpenBSD Secure Shell server: sshd. Running local boot scripts (/etc/rc.local) . INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: cannot execute "/tmp/loopd0" INIT: Id "0" respawning too fast: disabled for 5 minutes Debian GNU/Linux 11 debian ttyS0 debian login: