joao@joao-TM-4000:~/Transferências$ kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa325.mtd0.kwb -p Sending boot message. Please reboot the target...\ Sending boot image... 0 % [+� _ _ | \/____ _____| | | |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Oct 17 2012 - 15:22:14) Marvell version: 3.5.9 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8 DRAM CS[0] base 0x00000000 size 512MB DRAM Total size 512MB 16bit width Addresses 10M - 0M are saved for the U-Boot usage. Mem malloc Initialization (10M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) el address is 0xc80000. Streaming disablallocate dis USB 0: host mode [BlueDBG] reseting SoC P. PEX 0: PCI Express Root Complex PEX interface detected LlueDBG] reseting SoC Pex[1] 0 ... [BlueDBG] rseting SoC Pex[1] 1 ... reseting SoC Pex[1] 2 ... BG] reseting SoC Pex[1] 3 ... eDBG] reseting SoC Pex[ [BlueDBG] resx[1] 5 ... eseting SoC Pex[1] 6 ... reseting SoC Pex[1] 7 ... BG] reseting SoC Pex[1] 8 ... eDBG] reseting SoC Pex[1] 9 ... lueDBG] reseting SoC Pex[1] 10 ... PEX 1: incted no LinNet: egiga0 [PRIME] Hit any key to stop autoboot: 0 Reading dat from 0xce6000 -- 4%ing data from 0xcff800 -- 5% complete.ta from 0xd33000 -- 7% complete.ng data from 0xd4c800 -- 8% complete.data from 0xd66000 -- 9% complete.eading data from 0xd7f800 -- 10% complete. data from Reading ata from 0xe4c800 -- 1a from 0xeb3000 -- 22% complete.ete.ng data from 0xf39800 -ete.ata from 0xf53000 -- 27% complete.ading data from 0xf6c80mplete.ta from 0x1053000 -- 37% complete.ading data from 0x10d3000 -- 42% complete.g data from 0x10ec800 -- 43% complete.ata from 0x1106000 -- 44% complete.ading data from 0x1139800 -- 46% complete.-- 47% complete.ata from 0x1239800 -- 56% complete.ading data from 0x1386000 -- 69% complete.g data from 0x139f80Reding data from 0x13ec8omplete.ata from 0x141f800 -- 75% complete.ta from 0x1439800 -- 76% complete.eading data from 0x1453000 -- 77% m 0x151f800 -- 85% complete.data from 0x15b9800 -- 91% complete.a from 0x1639800 -- 96% complete.ading data from 0x169f800 -- 100% complete. 10485760 bytes read: OK me: Linux-2.6.31.802000000 ... Created: 2017-06-21 8:44:30 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5796368 Bytes = 5.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... +xmodem: Protocol error joao@joao-TM-4000:~/Transferências$