root@pcsita:/# minicom Welcome to minicom 2.4 OPTIONS: I18n Compiled on Sep 5 2010, 09:23:03. Port /dev/ttyUSB0 Press CTRL-A Z for help on special keys ¦ U-Boot SPL 2011.09-00002-g8d13bc8-dirty (Jul 21 2012 - 21:22:26) MMC: SUNXI SD/MMC: 0 Loading U-Boot... OK! Jumping to U-Boot... U-Boot 2011.09-00002-g8d13bc8-dirty (Jul 21 2012 - 21:22:26) Allwinner Technology CPU: SUNXI Family Board: A10-EVB DRAM: 512 MiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 reading script.bin 46600 bytes read reading uImage 2137452 bytes read ## Booting kernel from Legacy Image at 48000000 ... Image Name: Linux-3.0.36+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2137388 Bytes = 2 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... <6>Initializing cgroup subsys cpuset <6>Initializing cgroup subsys cpu <5>Linux version 3.0.36+ (gnexus@a10linux.org) (gcc version 4.6.1 (Sourcery CodeBench Lite2 CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: sun4i DRAM: 512<6>Total Detected Memory: 512MB with 1 banks <4>Ignoring unrecognised tag 0x00000000 <6>Memory Reserved(in bytes): <6> SYS: 0x43000000, 0x00010000 <6> LCD: 0x5a000000, 0x02000000 <6> G2D: 0x58000000, 0x01000000 <6> VE : 0x44000000, 0x05000000 Memory policy: ECC disabled, Data cache writeback <7>On node 0 totalpages: 114688 <7>free_area_init_node: node 0, pgdat c054f6bc, node_mem_map c0604000 <7> Normal zone: 896 pages used for memmap <7> Normal zone: 0 pages reserved <7> Normal zone: 113792 pages, LIFO batch:31 <7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 <7>pcpu-alloc: [0] 0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792 <5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 init=/init loglevel=8 root <6>PID hash table entries: 2048 (order: 1, 8192 bytes) <6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>allocated 1835008 bytes of page_cgroup <6>please try 'cgroup_disable=memory' option if you don't want memory cgroups <6>Memory: 448MB = 448MB total <5>Memory: 315636k/315636k available, 143116k reserved, 0K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xdc800000 - 0xf0000000 ( 312 MB) lowmem : 0xc0000000 - 0xdc000000 ( 448 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .init : 0xc0008000 - 0xc002c000 ( 144 kB) .text : 0xc002c000 - 0xc0517850 (5039 kB) .data : 0xc0518000 - 0xc0550040 ( 225 kB) .bss : 0xc0550064 - 0xc0603630 ( 718 kB) <6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>NR_IRQS:96 nr_irqs:96 96 <6>timer0: Periodic Mode <6>Console: colour dummy device 80x30 <6>Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408) <6>pid_max: default: 32768 minimum: 301 <6>Security Framework initialized <6>Mount-cache hash table entries: 512 <6>Initializing cgroup subsys cpuacct <6>Initializing cgroup subsys memory <6>Initializing cgroup subsys devices <6>Initializing cgroup subsys freezer <6>Initializing cgroup subsys blkio <6>Initializing cgroup subsys perf_event <6>CPU: Testing write buffer coherency: ok <6>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available <6>devtmpfs: initialized <6>print_constraints: dummy: <6>NET: Registered protocol family 16 <6>hw-breakpoint: debug architecture 0x4 unsupported. SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics <6>Initialize DMAC OK <6>bio: create slab at 0 <5>SCSI subsystem initialized <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>Advanced Linux Sound Architecture Driver Version 1.0.24. Init eGon pin module V2.0 <6>Switching to clocksource aw 64bits couter <5>FS-Cache: Loaded <6>CacheFiles: Loaded <6>Switched to NOHz mode on CPU #0 [usb_manager]: CONFIG_USB_SW_SUN4I_USB0_OTG [sw_hcd0]: usb host driver initialize........ [sw_hcd0]: open_usb_clock [sw_hcd0]: host_init_state = 0 [sw_hcd0]: platform is usb host [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 usin8 <6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver <6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1 <6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 <6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: sw_hcd host driver <6>usb usb1: Manufacturer: Linux 3.0.36+ sw_hcd-hcd <6>usb usb1: SerialNumber: sw_hcd_host0 <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 1 port detected wrn: hcd is not enable, need not start hcd [sw_hcd0]: sw_usb_host0_disable start -------sw_hcd0_soft_disconnect--------- [sw_hcd_host0]: Set USB Power OFF wrn: hcd is not enable, need not stop hcd [sw_hcd0]: close_usb_clock [sw_hcd0]: sw_usb_host0_disable end [sw_udc]: udc_init: version 20080411 axp driver uning configuration failed(561) axp driver uning configuration failed(573) <6>NET: Registered protocol family 2 <6>IP route cache hash table entries: 4096 (order: 2, 16384 bytes) <6>TCP established hash table entries: 16384 (order: 5, 131072 bytes) <6>TCP bind hash table entries: 16384 (order: 4, 65536 bytes) <6>TCP: Hash tables configured (established 16384 bind 16384) <6>TCP reno registered <6>UDP hash table entries: 256 (order: 0, 4096 bytes) <6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) <6>NET: Registered protocol family 1 [pm]aw_pm_init! <6>audit: initializing netlink socket (disabled) <5>type=2000 audit(0.319:1): initialized <5>VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>msgmni has been set to 616 <6>alg: No test for stdrng (krng) <6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) <6>io scheduler noop registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled ¦<6>serial8250.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.36+ (gnexus@a10linux.org) (gcc version 4.6.1 (Sourcery Co2 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: sun4i [ 0.000000] Total Detected Memory: 512MB with 1 banks [ 0.000000] Ignoring unrecognised tag 0x00000000 [ 0.000000] Memory Reserved(in bytes): [ 0.000000] SYS: 0x43000000, 0x00010000 [ 0.000000] LCD: 0x5a000000, 0x02000000 [ 0.000000] G2D: 0x58000000, 0x01000000 [ 0.000000] VE : 0x44000000, 0x05000000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 114688 [ 0.000000] free_area_init_node: node 0, pgdat c054f6bc, node_mem_map c0604000 [ 0.000000] Normal zone: 896 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 113792 pages, LIFO batch:31 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 init=/init lot [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 1835008 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 448MB = 448MB total [ 0.000000] Memory: 315636k/315636k available, 143116k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xdc800000 - 0xf0000000 ( 312 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .init : 0xc0008000 - 0xc002c000 ( 144 kB) [ 0.000000] .text : 0xc002c000 - 0xc0517850 (5039 kB) [ 0.000000] .data : 0xc0518000 - 0xc0550040 ( 225 kB) [ 0.000000] .bss : 0xc0550064 - 0xc0603630 ( 718 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:96 nr_irqs:96 96 [ 0.000000] timer0: Periodic Mode [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408) [ 0.040000] pid_max: default: 32768 minimum: 301 [ 0.040000] Security Framework initialized [ 0.040000] Mount-cache hash table entries: 512 [ 0.050000] Initializing cgroup subsys cpuacct [ 0.050000] Initializing cgroup subsys memory [ 0.060000] Initializing cgroup subsys devices [ 0.060000] Initializing cgroup subsys freezer [ 0.060000] Initializing cgroup subsys blkio [ 0.070000] Initializing cgroup subsys perf_event [ 0.070000] CPU: Testing write buffer coherency: ok [ 0.070000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.080000] devtmpfs: initialized [ 0.080000] print_constraints: dummy: [ 0.090000] NET: Registered protocol family 16 [ 0.090000] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.100000] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics [ 0.100000] Initialize DMAC OK [ 0.100000] bio: create slab at 0 [ 0.110000] SCSI subsystem initialized [ 0.110000] usbcore: registered new interface driver usbfs [ 0.120000] usbcore: registered new interface driver hub [ 0.120000] usbcore: registered new device driver usb [ 0.120000] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.130000] Init eGon pin module V2.0 [ 0.130000] Switching to clocksource aw 64bits couter [ 0.140000] FS-Cache: Loaded [ 0.140000] CacheFiles: Loaded [ 0.150000] Switched to NOHz mode on CPU #0 [ 0.150000] [usb_manager]: CONFIG_USB_SW_SUN4I_USB0_OTG [ 0.150000] [sw_hcd0]: usb host driver initialize........ [ 0.160000] [sw_hcd0]: open_usb_clock [ 0.180000] [sw_hcd0]: host_init_state = 0 [ 0.180000] [sw_hcd0]: platform is usb host [ 0.180000] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller a8 [ 0.190000] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver [ 0.200000] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1 [ 0.200000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.210000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.220000] usb usb1: Product: sw_hcd host driver [ 0.220000] usb usb1: Manufacturer: Linux 3.0.36+ sw_hcd-hcd [ 0.230000] usb usb1: SerialNumber: sw_hcd_host0 [ 0.230000] hub 1-0:1.0: USB hub found [ 0.230000] hub 1-0:1.0: 1 port detected [ 0.230000] wrn: hcd is not enable, need not start hcd [ 0.240000] [sw_hcd0]: sw_usb_host0_disable start [ 0.240000] -------sw_hcd0_soft_disconnect--------- [ 0.240000] [sw_hcd_host0]: Set USB Power OFF [ 0.240000] wrn: hcd is not enable, need not stop hcd [ 0.250000] [sw_hcd0]: close_usb_clock [ 0.260000] [sw_hcd0]: sw_usb_host0_disable end [ 0.260000] [sw_udc]: udc_init: version 20080411 [ 0.260000] axp driver uning configuration failed(561) [ 0.270000] axp driver uning configuration failed(573) [ 0.270000] NET: Registered protocol family 2 [ 0.270000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.280000] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.290000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.290000] TCP: Hash tables configured (established 16384 bind 16384) [ 0.300000] TCP reno registered [ 0.300000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.300000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.310000] NET: Registered protocol family 1 [ 0.310000] [pm]aw_pm_init! [ 0.320000] audit: initializing netlink socket (disabled) [ 0.320000] type=2000 audit(0.319:1): initialized [ 0.340000] VFS: Disk quotas dquot_6.5.2 [ 0.340000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.350000] msgmni has been set to 616 [ 0.350000] alg: No test for stdrng (krng) [ 0.350000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.360000] io scheduler noop registered [ 0.360000] io scheduler deadline registered [ 0.370000] io scheduler cfq registered (default) [ 0.370000] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.400000] serial8250.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A <6>console [ttyS0] enabled [ 1.040000] console [ttyS0] enabled [uart]: used uart info.: 0x05 [ 1.050000] [uart]: used uart info.: 0x05 <6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A [ 1.070000] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A [uart]: serial probe 0, membase (null) irq 1 mapbase 0x01c28000 [ 1.080000] [uart]: serial probe 0, membase (null) irq 1 mapbase 0x01c28000 <6>sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 3) is a U6_16550A [ 1.120000] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 3) is a U6_16550A [uart]: serial probe 2, membase (null) irq 3 mapbase 0x01c28800 [ 1.130000] [uart]: serial probe 2, membase (null) irq 3 mapbase 0x01c28800 <7>G2D: drv_g2d_init [ 1.140000] G2D: drv_g2d_init <6>G2D: g2dmem: g2d_start=58000000, g2d_size=1000000 [ 1.150000] G2D: g2dmem: g2d_start=58000000, g2d_size=1000000 <6>G2D: head:d8000000,tail:d9000000 [ 1.160000] G2D: head:d8000000,tail:d9000000 <6>G2D: Module initialized.major:251 [ 1.170000] G2D: Module initialized.major:251 <6>[drm] Initialized drm 1.1.0 20060810 [ 1.180000] [drm] Initialized drm 1.1.0 20060810 <6>brd: module loaded [ 1.180000] brd: module loaded [NAND]nand driver, init. [ 1.190000] [NAND]nand driver, init. cmu_clk is 360 [ 1.190000] cmu_clk is 360 nand clk init end [ 1.200000] nand clk init end offset 0xc: 0x6140 [ 1.200000] offset 0xc: 0x6140 offset 0x14: 0x82000008 [ 1.210000] offset 0x14: 0x82000008 [NAND] nand gpio_request [ 1.210000] [NAND] nand gpio_request [NAND] nand driver version: 0x2 0x9 [ 1.220000] [NAND] nand driver version: 0x2 0x9 nand interrupte register ok [ 1.230000] nand interrupte register ok ret of NFC_ChangMode is 0 [ 1.240000] ret of NFC_ChangMode is 0 dma_hdle is 0 [ 1.240000] dma_hdle is 0 dma_hdle is 10000008 [ 1.250000] dma_hdle is 10000008 cmu_clk is 360 [ 1.250000] cmu_clk is 360 nand clk init end [ 1.260000] nand clk init end offset 0xc: 0x6140 [ 1.260000] offset 0xc: 0x6140 offset 0x14: 0x82000005 [ 1.270000] offset 0x14: 0x82000005 PHY_PageReadSpare : too much ecc err,bank 0 block 0,page 1 [ 1.300000] PHY_PageReadSpare : too much ecc err,bank 0 block 0,page 1 PHY_PageReadSpare : too much ecc err,bank 0 block 0,page 0 [ 1.310000] PHY_PageReadSpare : too much ecc err,bank 0 block 0,page 0 insmod_device_driver [ 2.180000] [ 2.180000] [ 2.180000] insmod_device_driver [ 2.180000] [sw_udc]: [ 2.190000] [sw_udc]: sw_usb_device_enable start sw_usb_device_enable start [sw_udc]: [ 2.190000] [sw_udc]: usb_vbase = 0xf1c13000 usb_vbase = 0xf1c13000 [sw_udc]: [ 2.200000] [sw_udc]: sram_vbase = 0xf1c00000 sram_vbase = 0xf1c00000 [sw_udc]: [ 2.210000] [sw_udc]: open_usb_clock open_usb_clock udc->driver is null, udc is need not stop [ 2.240000] udc->driver is null, udc is need not stop [sw_udc]: [ 2.240000] [sw_udc]: sw_usb_device_enable end sw_usb_device_enable end The 0 disk name = bootloader, class name = DISK, disk size = 32768 [ 2.790000] The 0 disk name = bootloader, class name = DISK, disk size = 32768 The 1 disk name = env, class name = DISK, disk size = 4096 [ 2.810000] The 1 disk name = env, class name = DISK, disk size = 4096 The 2 disk name = boot, class name = DISK, disk size = 65536 [ 2.820000] The 2 disk name = boot, class name = DISK, disk size = 65536 The 3 disk name = system, class name = DISK, disk size = 524288 [ 2.830000] The 3 disk name = system, class name = DISK, disk size = 524288 The 4 disk name = data, class name = DISK, disk size = 524288 [ 2.840000] The 4 disk name = data, class name = DISK, disk size = 524288 The 5 disk name = misc, class name = DISK, disk size = 2048 [ 2.860000] The 5 disk name = misc, class name = DISK, disk size = 2048 The 6 disk name = recovery, class name = DISK, disk size = 65536 [ 2.870000] The 6 disk name = recovery, class name = DISK, disk size = 65536 The 7 disk name = cache, class name = DISK, disk size = 262144 [ 2.880000] The 7 disk name = cache, class name = DISK, disk size = 262144 The 8 disk name = private, class name = DISK, disk size = 2048 [ 2.890000] The 8 disk name = private, class name = DISK, disk size = 2048 The 9 disk name = sysrecovery, class name = DISK, disk size = 655360 [ 2.910000] The 9 disk name = sysrecovery, class name = DISK, disk size = 655360 The 10 disk name = UDISK, class name = DISK, disk size = 13424640 [ 2.920000] The 10 disk name = UDISK, class name = DISK, disk size = 13424640 The 10 disk size = 13424640 [ 2.930000] The 10 disk size = 13424640 part total count = 11 [ 2.940000] part total count = 11 <6> nanda: [ 2.940000] nanda: <6> nandb: unknown partition table [ 2.950000] nandb: unknown partition table <6> nandc: unknown partition table [ 2.960000] nandc: unknown partition table <6> nandd: unknown partition table [ 2.970000] nandd: unknown partition table <6> nande: unknown partition table [ 3.080000] nande: unknown partition table <6> nandf: unknown partition table [ 3.090000] nandf: unknown partition table <6> nandg: unknown partition table [ 3.100000] nandg: unknown partition table <6> nandh: unknown partition table [ 3.110000] nandh: unknown partition table <6> nandi: [ 3.120000] nandi: <6> nandj: unknown partition table [ 3.120000] nandj: unknown partition table <6> nandk: [ 3.130000] nandk: <6>benn: nand probe enter [ 3.140000] benn: nand probe enter [NAND]nand driver, ok. [ 3.140000] [NAND]nand driver, ok. <6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.150000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.160000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc05fe5dc [ 3.170000] [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc05fe5dc [sw-ehci1]: open clock [ 3.190000] [sw-ehci1]: open clock [sw-ehci1]: Set USB Power ON [ 3.210000] [sw-ehci1]: Set USB Power ON <6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.220000] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2 [ 3.230000] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2 <6>sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000 [ 3.240000] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000 <6>sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00 [ 3.270000] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00 ehci_irq: port change detect [ 3.270000] ehci_irq: port change detect <6>usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.280000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 <6>usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.290000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb2: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.310000] usb usb2: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>usb usb2: Manufacturer: Linux 3.0.36+ ehci_hcd [ 3.320000] usb usb2: Manufacturer: Linux 3.0.36+ ehci_hcd <6>usb usb2: SerialNumber: sw-ehci [ 3.330000] usb usb2: SerialNumber: sw-ehci <6>hub 2-0:1.0: USB hub found [ 3.340000] hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 1 port detected [ 3.350000] hub 2-0:1.0: 1 port detected [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc05fe6ec [ 3.350000] [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc05fe6ec [sw-ohci1]: open clock [ 3.370000] [sw-ohci1]: open clock <6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 3.390000] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3 [ 3.410000] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3 <6>sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400 [ 3.420000] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400 <6>usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.490000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 <6>usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.500000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb3: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 3.510000] usb usb3: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>usb usb3: Manufacturer: Linux 3.0.36+ ohci_hcd [ 3.530000] usb usb3: Manufacturer: Linux 3.0.36+ ohci_hcd <6>usb usb3: SerialNumber: sw-ohci [ 3.540000] usb usb3: SerialNumber: sw-ohci <6>hub 3-0:1.0: USB hub found [ 3.550000] hub 3-0:1.0: USB hub found <6>hub 3-0:1.0: 1 port detected [ 3.550000] hub 3-0:1.0: 1 port detected [sw-ehci2]: probe, pdev->name: sw-ehci, pdev->id: 2, sw_ehci: 0xc05fe800 [ 3.560000] [sw-ehci2]: probe, pdev->name: sw-ehci, pdev->id: 2, sw_ehci: 0xc05fe800 [sw-ehci2]: open clock [ 3.570000] [sw-ehci2]: open clock [sw-ehci2]: Set USB Power ON [ 3.600000] [sw-ehci2]: Set USB Power ON <6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.610000] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4 [ 3.620000] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4 <6>sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000 [ 3.630000] sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000 <6>usb 2-1: new high speed USB device number 2 using sw-ehci [ 3.670000] usb 2-1: new high speed USB device number 2 using sw-ehci <6>sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00 [ 3.700000] sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00 ehci_irq: port change detect [ 3.700000] ehci_irq: port change detect <6>usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.710000] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 <6>usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.720000] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb4: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.740000] usb usb4: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>usb usb4: Manufacturer: Linux 3.0.36+ ehci_hcd [ 3.750000] usb usb4: Manufacturer: Linux 3.0.36+ ehci_hcd <6>usb usb4: SerialNumber: sw-ehci [ 3.760000] usb usb4: SerialNumber: sw-ehci <6>hub 4-0:1.0: USB hub found [ 3.770000] hub 4-0:1.0: USB hub found <6>hub 4-0:1.0: 1 port detected [ 3.780000] hub 4-0:1.0: 1 port detected [sw-ohci2]: probe, pdev->name: sw-ohci, pdev->id: 2, sw_ohci: 0xc05fe910 [ 3.780000] [sw-ohci2]: probe, pdev->name: sw-ohci, pdev->id: 2, sw_ohci: 0xc05fe910 [sw-ohci2]: open clock [ 3.800000] [sw-ohci2]: open clock <6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 3.820000] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5 [ 3.840000] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5 <6>sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400 [ 3.850000] sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400 <6>usb 2-1: New USB device found, idVendor=0011, idProduct=7788 [ 3.910000] usb 2-1: New USB device found, idVendor=0011, idProduct=7788 <6>usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.930000] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 <6>usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.940000] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 <6>usb 2-1: Product: Mass Storage [ 3.950000] usb 2-1: Product: Mass Storage <6>usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.960000] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb 2-1: Manufacturer: Generic [ 3.980000] usb 2-1: Manufacturer: Generic <6>usb 2-1: SerialNumber: B908EFE9 [ 3.980000] usb 2-1: SerialNumber: B908EFE9 <6>usb usb5: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 3.990000] usb usb5: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>usb usb5: Manufacturer: Linux 3.0.36+ ohci_hcd [ 4.000000] usb usb5: Manufacturer: Linux 3.0.36+ ohci_hcd <6>usb usb5: SerialNumber: sw-ohci [ 4.010000] usb usb5: SerialNumber: sw-ohci <6>hub 5-0:1.0: USB hub found [ 4.020000] hub 5-0:1.0: USB hub found <6>hub 5-0:1.0: 1 port detected [ 4.030000] hub 5-0:1.0: 1 port detected <6>mousedev: PS/2 mouse device common for all mice [ 4.030000] mousedev: PS/2 mouse device common for all mice sunxi RTC version 0.1 [ 4.050000] sunxi RTC version 0.1 <6>sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380239881 [ 4.050000] sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380239881 <6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime [ 4.060000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime <6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:37 [ 4.070000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:37 <6>using rtc device, rtc, for alarms[ 4.080000] using rtc device, rtc, for alarms<6>sun0 [ 4.090000] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 <6>i2c /dev entries driver [ 4.100000] i2c /dev entries driver !!! base_Addr = 0xdc84ac00 [ 4.110000] !!! base_Addr = 0xdc84ac00 config i2c gpio with gpio_config api [ 4.110000] config i2c gpio with gpio_config api <6>usb 4-1: new high speed USB device number 2 using sw-ehci [ 4.120000] usb 4-1: new high speed USB device number 2 using sw-ehci twi0, apb clock = 24000000 [ 4.130000] twi0, apb clock = 24000000 <6>axp_mfd 0-0034: AXP (CHIP ID: 0x21) detected [ 4.140000] axp_mfd 0-0034: AXP (CHIP ID: 0x21) detected [AXP]axp driver uning configuration failed(323) [ 4.150000] [AXP]axp driver uning configuration failed(323) [AXP]power_start = 0 [ 4.160000] [AXP]power_start = 0 <6>I2C: i2c-0: AW16XX I2C adapter [ 4.170000] I2C: i2c-0: AW16XX I2C adapter **********start************ [ 4.170000] **********start************ 0x40 [ 4.180000] 0x40 0xf8 [ 4.180000] 0xf8 0x28 [ 4.180000] 0x28 0x0 [ 4.190000] 0x0 0x0 [ 4.190000] 0x0 **********end************ [ 4.190000] **********end************ !!! base_Addr = 0xdc84c000 [ 4.200000] !!! base_Addr = 0xdc84c000 twi1, apb clock = 24000000 [ 4.200000] twi1, apb clock = 24000000 <6>I2C: i2c-1: AW16XX I2C adapter [ 4.210000] I2C: i2c-1: AW16XX I2C adapter **********start************ [ 4.220000] **********start************ 0x40 [ 4.220000] 0x40 0xf8 [ 4.230000] 0xf8 0x58 [ 4.230000] 0x58 0x0 [ 4.230000] 0x0 0x0 [ 4.230000] 0x0 **********end************ [ 4.240000] **********end************ !!! base_Addr = 0xdc84e400 [ 4.240000] !!! base_Addr = 0xdc84e400 twi2, apb clock = 24000000 [ 4.250000] twi2, apb clock = 24000000 <6>I2C: i2c-2: AW16XX I2C adapter [ 4.260000] I2C: i2c-2: AW16XX I2C adapter **********start************ [ 4.260000] **********start************ 0x40 [ 4.270000] 0x40 0xf8 [ 4.270000] 0xf8 0x58 [ 4.270000] 0x58 0x0 [ 4.280000] 0x0 0x0 [ 4.280000] 0x0 **********end************ [ 4.280000] **********end************ <6>Linux media interface: v0.10 [ 4.290000] Linux media interface: v0.10 [cedar dev]: install start!!! [ 4.300000] [cedar dev]: install start!!! [cedar dev]: install end!!! [ 4.300000] [cedar dev]: install end!!! <6>print_constraints: axp20_ldo1: 1300 mV [ 4.310000] print_constraints: axp20_ldo1: 1300 mV <6>usb 4-1: New USB device found, idVendor=0bda, idProduct=8176 [ 4.320000] usb 4-1: New USB device found, idVendor=0bda, idProduct=8176 <6>usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.330000] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 <6>usb 4-1: Product: 802.11n WLAN Adapter [ 4.340000] usb 4-1: Product: 802.11n WLAN Adapter <6>usb 4-1: Manufacturer: Realtek [ 4.350000] usb 4-1: Manufacturer: Realtek <6>usb 4-1: SerialNumber: 00e04c000001 [ 4.360000] usb 4-1: SerialNumber: 00e04c000001 <6>print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV [ 4.370000] print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV <6>print_constraints: axp20_ldo3: 700 <--> 3500 mV at 2800 mV [ 4.380000] print_constraints: axp20_ldo3: 700 <--> 3500 mV at 2800 mV <6>print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 2800 mV [ 4.400000] print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 2800 mV <6>print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV [ 4.410000] print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV <6>print_constraints: axp20_buck3: 700 <--> 3500 mV at 1250 mV [ 4.420000] print_constraints: axp20_buck3: 700 <--> 3500 mV at 1250 mV <6>print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV [ 4.430000] print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV <6>input: axp20-supplyer as /devices/platform/sun4i-i2c.0/i2c-0/0-0034/axp20-supplyer.28/i0 [ 4.450000] input: axp20-supplyer as /devices/platform/sun4i-i2c.0/i2c-0/0-0034/axp20-s0 [AXP]axp driver uning configuration failed(1579) [ 4.470000] [AXP]axp driver uning configuration failed(1579) [AXP]pmu_suspendpwroff_vol = 3500 [ 4.480000] [AXP]pmu_suspendpwroff_vol = 3500 <6>cpuidle: using governor ladder [ 4.500000] cpuidle: using governor ladder <6>cpuidle: using governor menu [ 4.510000] cpuidle: using governor menu [mmc_pm]: no sdio card used in configuration [ 4.510000] [mmc_pm]: no sdio card used in configuration [mmc]: sunximmc_init [ 4.520000] [mmc]: sunximmc_init [mmc]: sunxi mmc controller using config : 0xb [ 4.530000] [mmc]: sunxi mmc controller using config : 0xb [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0 [ 4.540000] [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0 [mmc]: mmc 0 power off !! [ 4.550000] [mmc]: mmc 0 power off !! [mmc]: mmc0 Probe: base:0xdc854000 irq:32 dma:0 pdes:0xd9a44000, ret 0. [ 4.550000] [mmc]: mmc0 Probe: base:0xdc854000 irq:32 dma:0 pdes:0xd9a44000, ret 0. [mmc]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1 [ 4.570000] [mmc]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1 [mmc]: mmc 1 power off !! [ 4.580000] [mmc]: mmc 1 power off !! [mmc]: mmc1 Probe: base:0xdc856000 irq:33 dma:0 pdes:0xd9a4c000, ret 0. [ 4.590000] [mmc]: mmc1 Probe: base:0xdc856000 irq:33 dma:0 pdes:0xd9a4c000, ret 0. [mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3 [ 4.600000] [mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3 [mmc]: mmc 3 power off !! [ 4.610000] [mmc]: mmc 3 power off !! [mmc]: mmc3 Probe: base:0xdc858000 irq:35 dma:0 pdes:0xd9a50000, ret 0. [ 4.620000] [mmc]: mmc3 Probe: base:0xdc858000 irq:35 dma:0 pdes:0xd9a50000, ret 0. enter sun4i Audio codec!!! [ 4.630000] enter sun4i Audio codec!!! <6>sun4i audio support initialized [ 4.640000] sun4i audio support initialized audiocodec_adap_awxx_init: script_parser_fetch err. [ 4.650000] audiocodec_adap_awxx_init: script_parser_fetch err. sun4i Audio codec successfully loaded.. [ 4.660000] sun4i Audio codec successfully loaded.. <6>asoc: sndhdmi <-> sun4i-hdmiaudio.0 mapping ok [ 4.670000] asoc: sndhdmi <-> sun4i-hdmiaudio.0 mapping ok [SPDIF]sun4i-spdif cannot find any using configuration for controllers, return directly! [ 4.680000] [SPDIF]sun4i-spdif cannot find any using configuration for controllers, ret! [SPDIF]sndspdif cannot find any using configuration for controllers, return directly! [ 4.690000] [SPDIF]sndspdif cannot find any using configuration for controllers, return! [SPDIF]sun4i_sndspdif cannot find any using configuration for controllers, return directly! [ 4.710000] [SPDIF]sun4i_sndspdif cannot find any using configuration for controllers, ! [I2S]sun4i-i2s cannot find any using configuration for controllers, return directly! [ 4.730000] [I2S]sun4i-i2s cannot find any using configuration for controllers, return ! [I2S]sndi2s cannot find any using configuration for controllers, return directly! [ 4.740000] [I2S]sndi2s cannot find any using configuration for controllers, return dir! [I2S]sun4i_sndi2s cannot find any using configuration for controllers, return directly! [ 4.760000] [I2S]sun4i_sndi2s cannot find any using configuration for controllers, retu! <6>ALSA device list: [ 4.780000] ALSA device list: <6> #0: sun4i-CODEC Audio Codec [ 4.780000] #0: sun4i-CODEC Audio Codec <6> #1: sun4i-sndhdmi [ 4.790000] #1: sun4i-sndhdmi <6>TCP cubic registered [ 4.790000] TCP cubic registered <6>NET: Registered protocol family 10 [ 4.800000] NET: Registered protocol family 10 <6>NET: Registered protocol family 17 [ 4.810000] NET: Registered protocol family 17 <5>Registering the dns_resolver key type [ 4.820000] Registering the dns_resolver key type <6>VFP support v0.3: [ 4.830000] VFP support v0.3: implementor 41 architecture 3 part 33 implementor 41 architecture 3 part 30 variant c rev 3 <6>ThumbEE CPU extension supported. [ 4.840000] ThumbEE CPU extension supported. <5>Registering SWP/SWPB emulation handler [ 4.850000] Registering SWP/SWPB emulation handler <6>registered taskstats version 1 [ 4.860000] registered taskstats version 1 <4>[LCD] [ 4.860000] [LCD] lcd_module_init lcd_module_init <4>regulator_init_complete: axp20_buck3: incomplete constraints, leaving on [ 5.510000] regulator_init_complete: axp20_buck3: incomplete constraints, leaving on <4>regulator_init_complete: axp20_buck2: incomplete constraints, leaving on [ 5.520000] regulator_init_complete: axp20_buck2: incomplete constraints, leaving on <4>regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on [ 5.540000] regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on [mmc]: mmc 0 detect change, present 1 [ 5.550000] [mmc]: mmc 0 detect change, present 1 <4>regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on [ 5.560000] regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on <4>regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on [ 5.580000] regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on <4>regulator_init_complete: axp20_ldo1: incomplete constraints, leaving on [ 5.590000] regulator_init_complete: axp20_ldo1: incomplete constraints, leaving on <6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime [ 5.600000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime <6>sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:38 [ 5.610000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:0:38 <6>sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:00:38 UTC (1262304038) [ 5.620000] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:00:38 UTC (12623) <6>Waiting for root device /dev/mmcblk0p2... [ 5.640000] Waiting for root device /dev/mmcblk0p2... [mmc]: mmc 0 power on !! [ 5.860000] [mmc]: mmc 0 power on !! [mmc]: sdxc_request_done(L1113): [ 5.900000] [mmc]: sdxc_request_done(L1113): smc 0 err! smc 0 err, cmd 52, RTO !! [mmc]: sdxc_request_done(L1113): [ 5.910000] [mmc]: sdxc_request_done(L1113): smc 0 err! smc 0 err, cmd 52, RTO !! [mmc]: sdxc_request_done(L1113): [ 5.920000] [mmc]: sdxc_request_done(L1113): smc 0 err! smc 0 err, cmd 5, RTO !! [mmc]: sdxc_request_done(L1113): [ 5.940000] [mmc]: sdxc_request_done(L1113): smc 0 err! smc 0 err, cmd 5, RTO !! [mmc]: sdxc_request_done(L1113): [ 5.950000] [mmc]: sdxc_request_done(L1113): smc 0 err! smc 0 err, cmd 5, RTO !! [mmc]: sdxc_request_done(L1113): [ 5.960000] [mmc]: sdxc_request_done(L1113): smc 0 err! smc 0 err, cmd 5, RTO !! <6>mmc0: new high speed SDHC card at address 0d27 [ 6.110000] mmc0: new high speed SDHC card at address 0d27 <6>mmcblk0: mmc0:0d27 SD04G 3.69 GiB [ 6.120000] mmcblk0: mmc0:0d27 SD04G 3.69 GiB <6> mmcblk0: p1 p2 p3 [ 6.130000] mmcblk0: p1 p2 p3 <6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 6.460000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) <6>VFS: Mounted root (ext4 filesystem) on device 179:2. [ 6.470000] VFS: Mounted root (ext4 filesystem) on device 179:2. <6>devtmpfs: mounted [ 6.490000] devtmpfs: mounted <6>Freeing init memory: 144K [ 6.490000] Freeing init memory: 144K <4>Failed to execute /init. Attempting defaults... [ 6.500000] Failed to execute /init. Attempting defaults... INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Files under mount point '/run' will be hidden. ... (warning). [....] Starting the hotplug events dispatcher: udevd<30>udevd[141]: starting version 175 [ 8.200000] udevd[141]: starting version 175 . ok [....] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...<6>usbcore: registered new interface drives [ 9.150000] usbcore: registered new interface driver uas <6>Initializing USB Mass Storage driver... [ 9.360000] Initializing USB Mass Storage driver... <6>scsi0 : usb-storage 2-1:1.0 [ 9.380000] scsi0 : usb-storage 2-1:1.0 <6>usbcore: registered new interface driver usb-storage [ 9.380000] usbcore: registered new interface driver usb-storage <6>USB Mass Storage support registered. [ 9.480000] USB Mass Storage support registered. sw_usb_enable_hcd: usbc_num = 2 [ 9.570000] sw_usb_enable_hcd: usbc_num = 2 WRN:L894(drivers/usb/host/ehci_sun4i.c):[ 9.600000] WRN:L894(drivers/usb/host/ehci_sun4i ERR: not support sw_usb_enable_ehci WRN:L780(drivers/usb/host/ohci_sun4i.c):[ 9.710000] WRN:L780(drivers/usb/host/ohci_sun4i ERR: not support sw_usb_enable_ohci rtw driver version=v3.3.2_3192.20120103 [ 9.730000] [ 9.730000] rtw driver version=v3.3.2_3192.20120103 register rtw_netdev_ops to netdev_ops [ 9.750000] register rtw_netdev_ops to netdev_ops CHIP TYPE: RTL8188C_8192C [ 9.750000] CHIP TYPE: RTL8188C_8192C usb_endpoint_descriptor(0): [ 9.760000] [ 9.760000] usb_endpoint_descriptor(0): bLength=7 [ 9.770000] bLength=7 bDescriptorType=5 [ 9.770000] bDescriptorType=5 bEndpointAddress=81 [ 9.780000] bEndpointAddress=81 wMaxPacketSize=200 [ 9.780000] wMaxPacketSize=200 bInterval=0 [ 9.790000] bInterval=0 RT_usb_endpoint_is_bulk_in = 1 [ 9.790000] RT_usb_endpoint_is_bulk_in = 1 usb_endpoint_descriptor(1): [ 9.800000] [ 9.800000] usb_endpoint_descriptor(1): bLength=7 [ 9.810000] bLength=7 bDescriptorType=5 [ 9.810000] bDescriptorType=5 bEndpointAddress=2 [ 9.810000] bEndpointAddress=2 wMaxPacketSize=200 [ 9.820000] wMaxPacketSize=200 bInterval=0 [ 9.820000] bInterval=0 RT_usb_endpoint_is_bulk_out = 2 [ 9.830000] RT_usb_endpoint_is_bulk_out = 2 usb_endpoint_descriptor(2): [ 9.840000] [ 9.840000] usb_endpoint_descriptor(2): bLength=7 [ 9.850000] bLength=7 bDescriptorType=5 [ 9.850000] bDescriptorType=5 bEndpointAddress=3 [ 9.860000] bEndpointAddress=3 wMaxPacketSize=200 [ 9.860000] wMaxPacketSize=200 bInterval=0 [ 9.880000] bInterval=0 RT_usb_endpoint_is_bulk_out = 3 [ 9.880000] RT_usb_endpoint_is_bulk_out = 3 usb_endpoint_descriptor(3): [ 9.890000] [ 9.890000] usb_endpoint_descriptor(3): bLength=7 [ 9.900000] bLength=7 bDescriptorType=5 [ 9.900000] bDescriptorType=5 bEndpointAddress=84 [ 9.910000] bEndpointAddress=84 wMaxPacketSize=40 [ 9.910000] wMaxPacketSize=40 bInterval=1 [ 9.920000] bInterval=1 RT_usb_endpoint_is_int_in = 4, Interval = 1 [ 9.920000] RT_usb_endpoint_is_int_in = 4, Interval = 1 nr_endpoint=4, in_num=2, out_num=2 [ 9.930000] nr_endpoint=4, in_num=2, out_num=2 [ 9.930000] USB_SPEED_HIGH [ 9.940000] USB_SPEED_HIGH Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C. [ 9.940000] Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C. RF_Type is 3!! [ 9.950000] RF_Type is 3!! EEPROM type is E-FUSE [ 9.960000] EEPROM type is E-FUSE ====> ReadAdapterInfo8192C [ 9.960000] ====> ReadAdapterInfo8192C Boot from EFUSE, Autoload OK ! [ 9.970000] Boot from EFUSE, Autoload OK ! EEPROMVID = 0x0bda [ 10.130000] EEPROMVID = 0x0bda EEPROMPID = 0x8176 [ 10.130000] EEPROMPID = 0x8176 EEPROMCustomerID : 0x00 [ 10.140000] EEPROMCustomerID : 0x00 EEPROMSubCustomerID: 0x00 [ 10.150000] EEPROMSubCustomerID: 0x00 RT_CustomerID: 0x00 [ 10.150000] RT_CustomerID: 0x00 _ReadMACAddress MAC Address from EFUSE = 48:02:2a:9d:78:c1 [ 10.160000] _ReadMACAddress MAC Address from EFUSE = 48:02:2a:9d:78:c1 EEPROMRegulatory = 0x0 [ 10.170000] EEPROMRegulatory = 0x0 _ReadBoardType(0) [ 10.170000] _ReadBoardType(0) BT Coexistance = disable [ 10.180000] BT Coexistance = disable RT_ChannelPlan: 0x0a [ 10.180000] RT_ChannelPlan: 0x0a _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(10) ,bSupportRemoteWakeup(1) [ 10.190000] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(10) ,bSupportRemoteWakeup() ### PS params=> power_mgnt(1),usbss_enable(0) ### [ 10.210000] ### PS params=> power_mgnt(1),usbss_enable(0) ### ### AntDivCfg(0) [ 10.220000] ### AntDivCfg(0) readAdapterInfo_8192CU(): REPLACEMENT = 0 [ 10.220000] readAdapterInfo_8192CU(): REPLACEMENT = 0 <==== ReadAdapterInfo8192C in 270 ms [ 10.230000] <==== ReadAdapterInfo8192C in 270 ms padapter->pwrctrlpriv.bSupportRemoteWakeup~~~~~~ [ 10.240000] [ 10.240000] padapter->pwrctrlpriv.bSupportRemoteWakeup~~~~~~ padapter->pwrctrlpriv.bSupportRemoteWakeup~~~[1]~~~ [ 10.250000] [ 10.250000] padapter->pwrctrlpriv.bSupportRemoteWakeup~~~[1]~~~ rtw_macaddr_cfg MAC Address = 48:02:2a:9d:78:c1 [ 10.260000] rtw_macaddr_cfg MAC Address = 48:02:2a:9d:78:c1 MAC Address from pnetdev->dev_addr= 48:02:2a:9d:78:c1 [ 10.270000] MAC Address from pnetdev->dev_addr= 48:02:2a:9d:78:c1 bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 [ 10.290000] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 <6>usbcore: registered new interface driver rtl8192cu [ 10.300000] usbcore: registered new interface driver rtl8192cu <30>udevd[171]: renamed network interface wlan0 to wlan1 [ 10.350000] udevd[171]: renamed network interface wlan0 to wlan1 <5>scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.00 PQ: 0 ANSI: 2 [ 10.390000] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.00 PQ: 0 ANSI: 2 <5>sd 0:0:0:0: [sda] 3891200 512-byte logical blocks: (1.99 GB/1.85 GiB) [ 10.460000] sd 0:0:0:0: [sda] 3891200 512-byte logical blocks: (1.99 GB/1.85 GiB) <5>sd 0:0:0:0: [sda] Write Protect is off [ 10.480000] sd 0:0:0:0: [sda] Write Protect is off <7>sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 10.480000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 <3>sd 0:0:0:0: [sda] No Caching mode page present [ 10.500000] sd 0:0:0:0: [sda] No Caching mode page present <3>sd 0:0:0:0: [sda] Assuming drive cache: write through [ 10.510000] sd 0:0:0:0: [sda] Assuming drive cache: write through <3>sd 0:0:0:0: [sda] No Caching mode page present [ 10.530000] sd 0:0:0:0: [sda] No Caching mode page present <3>sd 0:0:0:0: [sda] Assuming drive cache: write through [ 10.540000] sd 0:0:0:0: [sda] Assuming drive cache: write through <6> sda: sda1 [ 10.570000] sda: sda1 <3>sd 0:0:0:0: [sda] No Caching mode page present [ 10.580000] sd 0:0:0:0: [sda] No Caching mode page present <3>sd 0:0:0:0: [sda] Assuming drive cache: write through [ 10.590000] sd 0:0:0:0: [sda] Assuming drive cache: write through <5>sd 0:0:0:0: [sda] Attached SCSI removable disk [ 10.600000] sd 0:0:0:0: [sda] Attached SCSI removable disk done. [....] Setting hostname to '(none)'...hostname: the specified hostname is invalid failed. [....] Activating swap:. ok <6>EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 13.320000] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [info] Loading kernel module 8192cu. [info] Loading kernel module mali. UMP<2>: [ 13.610000] UMP<2>: Inserting UMP device driver. Compiled: Jul 21 2012, time: 11 Inserting UMP device driver. Compiled: Jul 21 2012, time: 11:43:11 UMP<2>: [ 13.630000] UMP<2>: Using OS memory backend, allocation limit: 134217728 Using OS memory backend, allocation limit: 134217728 UMP: [ 13.650000] UMP: UMP device driver loaded UMP device driver loaded <6>mali: use config clk_div 3 [ 13.720000] mali: use config clk_div 3 <6>mali: clk_div 3 [ 13.720000] mali: clk_div 3 Mali: [ 13.740000] Mali: mali clock set completed, clock is 320000000 Mhz mali clock set completed, clock is 320000000 Mhz Mali: [ 13.760000] Mali: Mali device driver loaded Mali device driver loaded [....] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.20.1 Checking all file systems. [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that l. [....] Will now mount local filesystems:. ok [....] Will now activate swapfile swap:done. [....] Cleaning up temporary files...[....] Cleaning /tmp...done. . ok [....] Checking minimum space in /tmp...done. [....] Configuring network interfaces...Cannot find device "eth0" Failed to bring up eth0. Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Cannot find device "eth1" Bind socket to interface: No such device Failed to bring up eth1. SIOCSIFHWADDR: No such device wlan0: ERROR while getting interface flags: No such device wlan0: ERROR while getting interface flags: No such device Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; No such device. Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; No such device. Error for wireless request "Set ESSID" (8B1A) : SET failed on device wlan0 ; No such device. Cannot find device "wlan0" Failed to bring up wlan0. done. [....] Cleaning up temporary files.... ok [....] Setting kernel variables ... /etc/sysctl.conf...done. [....] Initializing random number generator...done. [....] startpar: service(s) returned failure: hostname.sh ... failed! INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting enhanced syslogd: rsyslogd. ok [....] Starting periodic command scheduler: cron. ok [....] Starting system message bus: dbus. ok [....] Starting OpenBSD Secure Shell server: sshd. ok [....] Running local boot scripts (/etc/rc.local). ok