Iomega ix2- ng freezes the install stage
Posted by Kicum
|
Iomega ix2- ng freezes the install stage May 05, 2020 05:06AM |
Registered: 3 years ago Posts: 14 |
Hello! I have an old Iomega ix2 -ng. I decided to install Debian on it, following the instructions of the respected Bodhi. Prepared a flash drive, inserted, launched. But when the kernel boot phase comes in, everything freezes, the indicator goes out.
Can someone help me?
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27GCY
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000'
Marvell>> setenv bootcmd 'run usb_boot'
Marvell>> setenv usb_root 'LABEL=rootfs'
Marvell>> setenv rootdelay 10
Marvell>> boot
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
.................................................................................................................................................................................................................
.......................................................................
4975125 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
.................................................................................................................................................................................................................
....................................................................................................................................................................................................................................................................................................................................................................................................................
....
............................................................................................................................
9713936 bytes read
## Booting image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-05-05 0:41:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4975061 Bytes = 4.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2019-08-25 2:22:50 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Marvell>> printenv baudrate=115200 loads_echo=0 rootpath=/srv/ubuntu run_diag=yes MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage lcd0_enable=0 lcd0_params=640x480-16@60 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 autoload=no ethact=egiga0 bootargs_root=root=/dev/ram0 bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) kernelimage=zImage initrdimage=mfginitrd mfgmodel=ix2 preroot_ver=0.0.2 fw_ver=0.0.2 bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000; uboot_ver=0.0.8 ethaddr=00:D0:B8:1D:7D:A9 serialNo=EUAC0200L4 modelname=31997200 serialno=0,01MuwrcB7lyFn/sJNvS+/yyCI0wXkRlFrlEB8OuEQQvFMHkASe8dp3t2E/zFs3Nt1O,EUAC0200L4, runintime=10800 ftpserver=192.168.43.4 testfile=100M mfgtest_state=system_tested_ok pre_path=IX2/1.0.3/download_runin.sh pre_path_conf=IX2/1.0.3/download_runin.conf pre_serverip=192.168.32.4 pre_user=ixxrunin pre_passwd=123 pre_dirzi=IX2/1.0.3 image_multi=yes console=console=ttyS0,115200 initrd_size=0x2f0000 loadaddr=0x2000000 serial_number=5563Y01001G152001BBJ0A1 standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000 bootfile=zImage usb_root=sdb1 usb_scan=setenv usb_device 0:1; setenv usb_root sdb1 make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext3 TFTFTP! tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm TFTP!=tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm 0x00800000 0x01100000; filesize=18af10 fileaddr=800000 gatewayip=192.168.1.1 netmask=255.255.255.0 ipaddr=192.168.1.123 serverip=192.168.1.181 bootargs_console=console=ttyS0,115200 root=/dev/sdb1 bootcmd_sata=ide reset; ext2load ide 0:1 0x01100000 /uInitrd; ext2load ide 0:1 0x00800000 /uImage bootcmd=setenv bootargs $(bootargs_console); run bootcmd_sata; bootm 0x00800000 0x01100000 bootcmd_usb=usb start; ext2load usb 0:1 0x800000 /uImage; ext2load usb 0:1 0x1100000 /uInitrd; bootm 0x800000 0x1100000; arcNumber=11 bootargs=console=ttyS0,115200 root=/dev/sdb1 stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no pcieTune1=no Environment size: 2857/4091 bytes Marvell>>
Can someone help me?
|
Re: Iomega ix2- ng freezes the install stage May 05, 2020 04:08PM |
Registered: 5 years ago Posts: 125 |
Hi, as these units have the old uboot you need to append the dtb to the kernel. These are the instructions under '4b' in Bodhi's guide;
4b. Boot with DTB file embedded in the kernel image (no U-Boot envs changes are needed if your system already booting on USB or HDD). Again, this step 4b is for stock U-Boot only.
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box.
Generate the uImage and uInitrd (the kernel files vmlinuz-5.6.5-kirkwood-tld-1 and initrd.img-5.6.5-kirkwood-tld-1 were generated by dpkg in Step 3):
Use the IX2 dtb instead of the goflex and it should boot without issue.
4b. Boot with DTB file embedded in the kernel image (no U-Boot envs changes are needed if your system already booting on USB or HDD). Again, this step 4b is for stock U-Boot only.
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box.
Generate the uImage and uInitrd (the kernel files vmlinuz-5.6.5-kirkwood-tld-1 and initrd.img-5.6.5-kirkwood-tld-1 were generated by dpkg in Step 3):
cd /boot mv uImage uImage.orig mv uInitrd uInitrd.orig cp -a zImage-5.6.5-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-goflexnet.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n 5.6.5-kirkwood-tld-1 -d zImage.fdt uImage mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.6.5-kirkwood-tld-1 -d initrd.img-5.6.5-kirkwood-tld-1 uInitrd
Use the IX2 dtb instead of the goflex and it should boot without issue.
|
Re: Iomega ix2- ng freezes the install stage May 05, 2020 04:44PM |
Admin Registered: 13 years ago Posts: 18,543 |
J,
It looks like the uImage had a DTB appended to it.
But let Kicum response first, before we can speculate further.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
It looks like the uImage had a DTB appended to it.
## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-05-05 0:41:36 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4975061 Bytes = 4.7 MB
But let Kicum response first, before we can speculate further.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 05, 2020 07:24PM |
Registered: 3 years ago Posts: 14 |
|
Re: Iomega ix2- ng freezes the install stage May 05, 2020 07:49PM |
Admin Registered: 13 years ago Posts: 18,543 |
Kicum,
Did you append a wrong DTB before?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Did you append a wrong DTB before?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 05, 2020 08:19PM |
Registered: 3 years ago Posts: 14 |
|
Re: Iomega ix2- ng freezes the install stage May 05, 2020 08:39PM |
Admin Registered: 13 years ago Posts: 18,543 |
Kicum Wrote:
-------------------------------------------------------
> Yes. I just copied the command without looking:)
Cool! Because the booting behavior indicated that there was a DTB, just one for the wrong box!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Yes. I just copied the command without looking:)
Cool! Because the booting behavior indicated that there was a DTB, just one for the wrong box!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 05, 2020 08:43PM |
Registered: 5 years ago Posts: 125 |
|
Re: Iomega ix2- ng freezes the install stage May 06, 2020 04:20PM |
Registered: 3 years ago Posts: 14 |
Hi! Now I have a new problem. I can not boot from the hdd. I also made rootfs on the hdd as a USB flash drive. I can’t configure the environment.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
** Unable to read "/uInitrd" from ide 0:1 **
** Unable to read "/uImage" from ide 0:1 **
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>
Marvell>> printenv baudrate=115200 loads_echo=0 rootpath=/srv/ubuntu run_diag=yes MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage lcd0_enable=0 lcd0_params=640x480-16@60 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 autoload=no ethact=egiga0 bootargs_root=root=/dev/ram0 bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) kernelimage=zImage initrdimage=mfginitrd mfgmodel=ix2 preroot_ver=0.0.2 fw_ver=0.0.2 bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000; uboot_ver=0.0.8 ethaddr=00:D0:B8:1D:7D:A9 serialNo=EUAC0200L4 modelname=31997200 serialno=0,01MuwrcB7lyFn/sJNvS+/yyCI0wXkRlFrlEB8OuEQQvFMHkASe8dp3t2E/zFs3Nt1O,EUAC0200L4, runintime=10800 ftpserver=192.168.43.4 testfile=100M mfgtest_state=system_tested_ok pre_path=IX2/1.0.3/download_runin.sh pre_path_conf=IX2/1.0.3/download_runin.conf pre_serverip=192.168.32.4 pre_user=ixxrunin pre_passwd=123 pre_dirzi=IX2/1.0.3 image_multi=yes console=console=ttyS0,115200 initrd_size=0x2f0000 loadaddr=0x2000000 serial_number=5563Y01001G152001BBJ0A1 standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000 bootfile=zImage usb_root=sdb1 usb_scan=setenv usb_device 0:1; setenv usb_root sdb1 make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext3 TFTFTP! tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm TFTP!=tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm 0x00800000 0x01100000; filesize=18af10 fileaddr=800000 gatewayip=192.168.1.1 netmask=255.255.255.0 ipaddr=192.168.1.123 serverip=192.168.1.181 bootargs_console=console=ttyS0,115200 root=/dev/sdb1 bootcmd_sata=ide reset; ext2load ide 0:1 0x01100000 /uInitrd; ext2load ide 0:1 0x00800000 /uImage bootcmd=setenv bootargs $(bootargs_console); run bootcmd_sata; bootm 0x00800000 0x01100000 bootcmd_usb=usb start; ext2load usb 0:1 0x800000 /uImage; ext2load usb 0:1 0x1100000 /uInitrd; bootm 0x800000 0x1100000; arcNumber=11 stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no pcieTune1=no bootargs=console=ttyS0,115200 root=/dev/sdb1 Environment size: 2857/4091 bytes
root@debian:~# fdisk -l Disk /dev/mtdblock0: 504 KiB, 516096 bytes, 1008 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock1: 4 KiB, 4096 bytes, 8 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock2: 4 KiB, 4096 bytes, 8 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/sda: 1.8 TiB, 2000398934016 bytes, 3907029168 sectors Disk model: ST32000542AS Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x0cf2e517 Device Boot Start End Sectors Size Id Type /dev/sda1 2048 2099199 2097152 1G 83 Linux /dev/sda2 2099200 3147775 1048576 512M 82 Linux swap / Solaris /dev/sda3 3147776 3907028991 3903881216 1.8T 83 Linux Disk /dev/sdb: 3.7 GiB, 3984588800 bytes, 7782400 sectors Disk model: UDisk Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x90909090 Device Boot Start End Sectors Size Id Type /dev/sdb1 2048 2099199 2097152 1G 83 Linux
|
Re: Iomega ix2- ng freezes the install stage May 06, 2020 04:35PM |
Admin Registered: 13 years ago Posts: 18,543 |
Kicum,
You need to change the SATA boot:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
You need to change the SATA boot:
setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 06, 2020 04:45PM |
Registered: 3 years ago Posts: 14 |
I've changed . But now freezes
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
9713936 bytes read
4976325 bytes read
## Booting image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-05-06 3:27:34 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4976261 Bytes = 4.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2020-05-06 3:27:13 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
|
Re: Iomega ix2- ng freezes the install stage May 06, 2020 04:47PM |
Admin Registered: 13 years ago Posts: 18,543 |
Looks like it is the same problem as before with USB rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 06, 2020 05:17PM |
Registered: 3 years ago Posts: 14 |
I rewrote the new rootfs on hdd. Same thing happens
Edited 1 time(s). Last edit at 05/06/2020 05:47PM by Kicum.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
9713936 bytes read
4976325 bytes read
## Booting image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-05-06 22:05:45 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4976261 Bytes = 4.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2020-05-06 22:06:10 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Edited 1 time(s). Last edit at 05/06/2020 05:47PM by Kicum.
|
Re: Iomega ix2- ng freezes the install stage May 06, 2020 06:18PM |
Registered: 3 years ago Posts: 14 |
|
Re: Iomega ix2- ng freezes the install stage May 06, 2020 10:35PM |
Admin Registered: 13 years ago Posts: 18,543 |
Kicum Wrote:
-------------------------------------------------------
> Maybe I should boot under USB and prepare hdd from
> there?
Good idea! you can either:
- Boot with USB, prepare the HDD and then run rsync to copy all the files over.
- Bringthe USB drive to another Linux computer, and then backup to a tarball, bring it back and restore to the HDD (I would do this, since it will create a backup for the USB rootfs that you can keep to recreate it again).
https://forum.doozan.com/read.php?2,12096,24034#msg-24034
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Maybe I should boot under USB and prepare hdd from
> there?
Good idea! you can either:
- Boot with USB, prepare the HDD and then run rsync to copy all the files over.
- Bringthe USB drive to another Linux computer, and then backup to a tarball, bring it back and restore to the HDD (I would do this, since it will create a backup for the USB rootfs that you can keep to recreate it again).
https://forum.doozan.com/read.php?2,12096,24034#msg-24034
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 04:26AM |
Registered: 5 years ago Posts: 125 |
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 04:43AM |
Admin Registered: 13 years ago Posts: 18,543 |
> Try
> 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Right! That's need to be done to boot with stock u-boot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Right! That's need to be done to boot with stock u-boot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 11:51AM |
Registered: 3 years ago Posts: 14 |
Hello! I booted the system from a usb flash drive. deleted old partitions. Created a new formatted boot partition in ext 2.
Then the
Reboot
Edited 1 time(s). Last edit at 05/07/2020 03:27PM by Kicum.
Then the
rsync -aAXv --exclude={"/dev/*","/proc/*","/sys/*","/tmp/*","/run/*","/mnt/*"} / /mnt/sda
copied the rootfs section.
Reboot
root@debian:/# cd /mnt/sda1 root@debian:/mnt/sda1# ls . dev media run usr .. etc mnt sbin var Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 home opt srv bin lib proc sys boot lost+found root tmp root@debian:/mnt/sda1# cd .. root@debian:/mnt# umount /mnt/sda1 root@debian:/mnt# reboot Broadcast message from root@debian (ttyS0) (Thu May 7 09:22:37 2020): INIT: Se[info] Using makefile-style concurrent boot in runlevel 6. [ ok ] Stopping hotplug events dispatcher: systemd-udevd. [ ok ] Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Stopping busybox' klogd implementation: klogd1397 (klogd) Stopped klogd (pid 1397). . ok [....] Stopping busybox' syslogd implementation: syslogd1370 (syslogd) . ok [ ok ] Stopping NFS kernel daemon: mountd nfsd. [ ok ] Unexporting directories for NFS kernel daemon.... [ ok ] Asking all remaining processes to terminate...done. [ ok ] All processes ended within 1 seconds...done. [ ok ] Stopping NFS common utilities: idmapd statd. [info] Saving the system clock. [info] Hardware Clock updated to Thu May 7 09:22:42 PDT 2020. [ ok ] Stopping RPC port mapper daemon: rpcbind. [....] Deconfiguring network interfaces...Removed stale PID file Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:d0:b8:1d:7d:a9 Sending on LPF/eth0/00:d0:b8:1d:7d:a9 Sending on Socket/fallback DHCPRELEASE of 192.168.1.34 on eth0 to 192.168.1.1 port 67 send_packet: Network is unreachable send_packet: please consult README file regarding broadcast address. dhclient.c:2878: Failed to send 300 byte long packet over fallback interface. done. [ ok ] Saving random seed...done. [....] Will now unmount temporary filesystems:umount: /tmp unmounted . ok [ ok ] Will now deactivate swap:. [ ok ] Mounting root filesystem read-only...done. [info] Will now restart. [11978.629893][ T2215] sd 0:0:0:0: [sda] Synchronizing SCSI cache [11978.638341][ T2215] reboot: Restarting system __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0 Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done Found ADT7473, program PWM1 ... OK [1024kB@f8000000] Flash: 1 MB Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. PEX 1: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) ** Unable to read "/uInitrd" from ide 0:1 ** ** Unable to read "/uImage" from ide 0:1 ** ## Booting image at 00800000 ... Bad Magic Number Marvell>> reset __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0 Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done Found ADT7473, program PWM1 ... OK [1024kB@f8000000] Flash: 1 MB Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. PEX 1: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> Marvell>> Marvell>> Marvell>> Marvell>> Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage Marvell>> boot Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) 9713936 bytes read 4988970 bytes read ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-05-05 22:44:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4988906 Bytes = 4.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2020-05-05 22:45:35 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...What to do in this case?
Edited 1 time(s). Last edit at 05/07/2020 03:27PM by Kicum.
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 04:57PM |
Admin Registered: 13 years ago Posts: 18,543 |
Try
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x02100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage' setenv bootcmd 'setenv bootargs $(bootargs_console) earlyprintk=serial; run bootcmd_sata; bootm 0x00800000 0x02100000' printenv boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 05:30PM |
Registered: 3 years ago Posts: 14 |
go loading, only then it goes here
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x02100000 /boot/uIni trd; ext2load ide 0:1 0x00800000 /boot/uImage'
Marvell>> setenv bootcmd 'setenv bootargs $(bootargs_console) earlyprintk=serial; run bootcmd_sata; bootm 0x00800000 0x02100000'
Marvell>> printenv
Unknown command 'Đ·Đşâ–’printenv' - try 'help'
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
autoload=no
ethact=egiga0
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
mfgmodel=ix2
preroot_ver=0.0.2
fw_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
ethaddr=00:D0:B8:1D:7D:A9
serialNo=EUAC0200L4
modelname=31997200
serialno=0,01MuwrcB7lyFn/sJNvS+/yyCI0wXkRlFrlEB8OuEQQvFMHkASe8dp3t2E/zFs3Nt1O,EUAC0200L4,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.0.3/download_runin.sh
pre_path_conf=IX2/1.0.3/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.0.3
image_multi=yes
console=console=ttyS0,115200
initrd_size=0x2f0000
loadaddr=0x2000000
serial_number=5563Y01001G152001BBJ0A1
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000
bootfile=zImage
usb_root=sdb1
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext3
TFTFTP! tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm
TFTP!=tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm 0x00800000 0x01100000;
filesize=18af10
fileaddr=800000
gatewayip=192.168.1.1
netmask=255.255.255.0
ipaddr=192.168.1.123
serverip=192.168.1.181
bootargs_console=console=ttyS0,115200 root=/dev/sdb1
bootcmd_usb=usb start; ext2load usb 0:1 0x800000 /uImage; ext2load usb 0:1 0x1100000 /uInitrd; bootm 0x800000 0x1100000;
arcNumber=11
bootargs=console=ttyS0,115200 root=/dev/sdb1
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
bootcmd_sata=ide reset; ext2load ide 0:1 0x02100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
bootcmd=setenv bootargs $(bootargs_console) earlyprintk=serial; run bootcmd_sata; bootm 0x00800000 0x02100000
Environment size: 2886/4091 bytes
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
9713936 bytes read
4988970 bytes read
## Booting image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:44:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4988906 Bytes = 4.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:45:35 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 8.231471][ T1] printk: console [ttyS0] enabled
[ 8.241241][ T1] printk: bootconsole [earlycon0] disabled
[ 8.258195][ T1] loop: module loaded
[ 8.262548][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 8.270133][ T1] scsi host0: sata_mv
[ 8.274408][ T1] scsi host1: sata_mv
[ 8.278521][ T1] ata1: SATA max UDMA/133 irq 34
[ 8.283333][ T1] ata2: SATA max UDMA/133 irq 34
[ 8.289522][ T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 8.295058][ T1] 3 fixed-partitions partitions found on MTD device spi0.0
[ 8.302172][ T1] Creating 3 MTD partitions on "spi0.0":
[ 8.307683][ T1] 0x000000000000-0x00000007e000 : "u-boot"
[ 8.313379][ T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[ 8.323383][ T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[ 8.329535][ T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[ 8.340870][ T1] 0x00000007f000-0x000000080000 : "u-boot env"
[ 8.346901][ T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[ 8.359067][ T1] libphy: Fixed MDIO Bus: probed
[ 8.364456][ T1] libphy: orion_mdio_bus: probed
[ 8.379991][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.387878][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[ 8.395641][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[ 8.405265][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.412577][ T1] ehci-pci: EHCI PCI platform driver
[ 8.417775][ T1] ehci-orion: EHCI orion driver
[ 8.422669][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 8.428917][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 8.437424][ T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 8.468452][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 8.475365][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 8.484385][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.492349][ T1] usb usb1: Product: EHCI Host Controller
[ 8.497942][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[ 8.505297][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 8.511195][ T1] hub 1-0:1.0: USB hub found
[ 8.515689][ T1] hub 1-0:1.0: 1 port detected
[ 8.520886][ T1] usbcore: registered new interface driver usb-storage
[ 8.527903][ T1] mousedev: PS/2 mouse device common for all mice
[ 8.534674][ T1] rtc-mv f1010300.rtc: registered as rtc0
[ 8.540436][ T1] i2c /dev entries driver
[ 8.545762][ T1] device-mapper: uevent: version 1.0.3
[ 8.551389][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 8.560880][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 8.568165][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 8.575549][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 8.582979][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 8.589829][ T1] device-mapper: raid: Loading target version 1.14.0
[ 8.597457][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 8.603856][ T1] drop_monitor: Initializing network drop monitor service
[ 8.611121][ T1] NET: Registered protocol family 17
[ 8.616484][ T1] Key type dns_resolver registered
[ 8.622134][ T1] registered taskstats version 1
[ 8.626943][ T1] Loading compiled-in X.509 certificates
[ 8.633375][ T1] zswap: loaded using pool lzo/zbud
[ 8.706033][ T1] Key type big_key registered
[ 8.741668][ T1] Key type encrypted registered
[ 8.747878][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T22:23:33 UTC (1588890213)
[ 8.788462][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 8.799960][ T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[ 8.806342][ T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.820571][ T112] ata1.00: configured for UDMA/133
[ 8.835951][ T7] scsi 0:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5
[ 8.845508][ T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 8.854430][ T116] sd 0:0:0:0: [sda] Write Protect is off
[ 8.860094][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.921310][ T116] sda: sda1 sda2 sda3
[ 8.926562][ T116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.189808][ T114] ata2: SATA link down (SStatus 0 SControl F300)
[ 9.209047][ T1] Freeing unused kernel memory: 1024K
[ 9.214679][ T1] Checked W+X mappings: passed, no W+X pages found
[ 9.221084][ T1] Run /init as init process
Loading, please wait...
Starting version 241
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device. Common problems:
- Boot args (cat /proc/cmdline)
- Check rootdelay= (did the system wait long enough?)
- Missing modules (cat /proc/modules; ls /dev)
ALERT! /dev/sdb1 does not exist. Dropping to a shell!
BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 05:39PM |
Admin Registered: 13 years ago Posts: 18,543 |
Kicum,
Boot with USB like you did before
And post the entire serial console log here (make sure that it does not get cut off on the right side).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Boot with USB like you did before
Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000' Marvell>> setenv bootcmd 'run usb_boot' Marvell>> setenv usb_root 'LABEL=rootfs' Marvell>> setenv rootdelay 10 Marvell>> boot
And post the entire serial console log here (make sure that it does not get cut off on the right side).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 05:55PM |
Registered: 3 years ago Posts: 14 |
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000'
Marvell>> setenv bootcmd 'run usb_boot'
Marvell>> setenv usb_root 'LABEL=rootfs'
Marvell>> setenv rootdelay 10
Marvell>> boot
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
........................................................................
4988970 bytes read
.
...
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
....................................................................................................................................................................................................................................................................................................................................................................................................................
....
............................................................................................................................
9713936 bytes read
## Booting image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:44:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4988906 Bytes = 4.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:45:35 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 8.231807][ T1] printk: console [ttyS0] enabled
[ 8.241587][ T1] printk: bootconsole [earlycon0] disabled
[ 8.258523][ T1] loop: module loaded
[ 8.262871][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 8.270452][ T1] scsi host0: sata_mv
[ 8.274730][ T1] scsi host1: sata_mv
[ 8.278847][ T1] ata1: SATA max UDMA/133 irq 34
[ 8.283657][ T1] ata2: SATA max UDMA/133 irq 34
[ 8.289842][ T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 8.295380][ T1] 3 fixed-partitions partitions found on MTD device spi0.0
[ 8.302497][ T1] Creating 3 MTD partitions on "spi0.0":
[ 8.308007][ T1] 0x000000000000-0x00000007e000 : "u-boot"
[ 8.313703][ T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[ 8.323700][ T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[ 8.329849][ T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[ 8.341177][ T1] 0x00000007f000-0x000000080000 : "u-boot env"
[ 8.347207][ T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[ 8.359368][ T1] libphy: Fixed MDIO Bus: probed
[ 8.364765][ T1] libphy: orion_mdio_bus: probed
[ 8.380184][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.388071][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[ 8.395842][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[ 8.405467][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.412777][ T1] ehci-pci: EHCI PCI platform driver
[ 8.417976][ T1] ehci-orion: EHCI orion driver
[ 8.422872][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 8.429118][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 8.437623][ T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 8.468767][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 8.475687][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 8.484709][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.492673][ T1] usb usb1: Product: EHCI Host Controller
[ 8.498265][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[ 8.505620][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 8.511522][ T1] hub 1-0:1.0: USB hub found
[ 8.516011][ T1] hub 1-0:1.0: 1 port detected
[ 8.521209][ T1] usbcore: registered new interface driver usb-storage
[ 8.528233][ T1] mousedev: PS/2 mouse device common for all mice
[ 8.535000][ T1] rtc-mv f1010300.rtc: registered as rtc0
[ 8.540758][ T1] i2c /dev entries driver
[ 8.546085][ T1] device-mapper: uevent: version 1.0.3
[ 8.551713][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 8.561206][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 8.568492][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 8.575872][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 8.583304][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 8.590154][ T1] device-mapper: raid: Loading target version 1.14.0
[ 8.597787][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 8.604189][ T1] drop_monitor: Initializing network drop monitor service
[ 8.611453][ T1] NET: Registered protocol family 17
[ 8.616818][ T1] Key type dns_resolver registered
[ 8.622722][ T1] registered taskstats version 1
[ 8.627529][ T1] Loading compiled-in X.509 certificates
[ 8.633219][ T1] zswap: loaded using pool lzo/zbud
[ 8.705818][ T1] Key type big_key registered
[ 8.741523][ T1] Key type encrypted registered
[ 8.747858][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T22:53:04 UTC (1588891984)
[ 8.788779][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 8.800307][ T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[ 8.806694][ T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.820933][ T112] ata1.00: configured for UDMA/133
[ 8.836314][ T7] scsi 0:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5
[ 8.845862][ T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 8.854776][ T116] sd 0:0:0:0: [sda] Write Protect is off
[ 8.860433][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.888771][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 8.922019][ T116] sda: sda1 sda2 sda3
[ 8.927288][ T116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.190120][ T114] ata2: SATA link down (SStatus 0 SControl F300)
[ 9.209553][ T1] Freeing unused kernel memory: 1024K
[ 9.215185][ T1] Checked W+X mappings: passed, no W+X pages found
[ 9.221593][ T1] Run /init as init process
Loading, please wait...
Starting version 241
[ 14.078763][ T15] usb 1-1: device descriptor read/64, error -110
[ 14.399751][ T15] usb 1-1: New USB device found, idVendor=abcd, idProduct=1234, bcdDevice= 1.00
[ 14.408675][ T15] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 14.416566][ T15] usb 1-1: Product: UDisk
[ 14.421741][ T15] usb 1-1: Manufacturer: General
[ 14.426637][ T15] usb 1-1: SerialNumber: 1804251030306948643714
[ 14.434521][ T15] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 14.441726][ T15] scsi host2: usb-storage 1-1:1.0
[ 14.458099][ T169] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
[ 15.449704][ T116] scsi 2:0:0:0: Direct-Access General UDisk 5.00 PQ: 0 ANSI: 2
[ 15.462801][ T23] sd 2:0:0:0: [sdb] 7782400 512-byte logical blocks: (3.98 GB/3.71 GiB)
[ 15.476417][ T23] sd 2:0:0:0: [sdb] Write Protect is off
[ 15.482399][ T23] sd 2:0:0:0: [sdb] No Caching mode page found
[ 15.488438][ T23] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 15.549487][ T23] sdb: sdb1
[ 15.560667][ T23] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
fsck: error 2 (No such file or directory) while executing fsck.ext2 for /dev/sdb1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[....] Synthesizing the initial hotplug events (devices)...[ 31.571483][ T374] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ ok done.
[ 31.612349][ T384] systemd-udevd[384]: Using default interface naming scheme 'v240'.
[....] Waiting for /dev to be fully populated...[ 31.752546][ T384] systemd-udevd[384]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.851378][ T385] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[ 31.946624][ T377] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 31.981851][ T385] watchdog: f1020300.watchdog-timer: falling back to default timeout (21)
[ 32.092509][ T385] orion_wdt: Initial timeout 21 sec
[ 32.112663][ T377] adt7475 0-002e: ADT7473 device, revision 0
[ 32.152871][ T386] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 32.207611][ T377] adt7475 0-002e: Optional features: fan4 pwm2
[ 32.223892][ T374] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 32.239155][ T386] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 32.292800][ C0] random: crng init done
[ 32.390870][ T386] systemd-udevd[386]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[....] Will now check root file system:fsck from util-linux 2.33.1
[/sbin/fsck.ext2 (1) -- /] fsck.ext2 -y -C0 /dev/sdb1
e2fsck 1.44.5 (15-Dec-2018)
rootfs: clean, 15113/65536 files, 210180/262144 blocks
. ok
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:d0:b8:1d:7d:a9
Sending on LPF/eth0/00:d0:b8:1d:7d:a9
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
done.
[....] Starting RPC port mapper daemon: rpcbind[ 97.950358][ T1226] NET: Registered protocol family 10
[ 97.956857][ T1226] Segment Routing with IPv6
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1367 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1394 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 10 debian ttyS0
debian login:
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 06:12PM |
Admin Registered: 13 years ago Posts: 18,543 |
Log in and then post dmesg output:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
dmesg
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 06:37PM |
Registered: 3 years ago Posts: 14 |
Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Thu May 7 16:24:10 PDT 2020 on ttyS0 Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Lenovo IX2-ng [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 234780K/262144K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 27364K reserved, 0K cma-reserved) [ 0.000000] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000006] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008509] Switching to timer-based delay loop, resolution 5ns [ 0.015663] Console: colour dummy device 80x30 [ 0.020843] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032046] pid_max: default: 32768 minimum: 301 [ 0.037608] LSM: Security Framework initializing [ 0.043068] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.050385] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.058786] *** VALIDATE proc *** [ 0.062972] *** VALIDATE cgroup1 *** [ 0.067229] *** VALIDATE cgroup2 *** [ 0.071576] CPU: Testing write buffer coherency: ok [ 0.078433] Setting up static identity map for 0x100000 - 0x100058 [ 0.085554] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.091592] rcu: Hierarchical SRCU implementation. [ 0.099511] devtmpfs: initialized [ 0.108598] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.119137] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.126111] xor: measuring software checksum speed [ 0.228532] arm4regs : 1446.000 MB/sec [ 0.328531] 8regs : 868.000 MB/sec [ 0.428526] 32regs : 1262.000 MB/sec [ 0.433382] xor: using function: arm4regs (1446.000 MB/sec) [ 0.439648] prandom: seed boundary self test passed [ 0.448337] prandom: 100 self tests passed [ 0.453132] pinctrl core: initialized pinctrl subsystem [ 0.460148] NET: Registered protocol family 16 [ 0.465898] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.474086] audit: initializing netlink subsys (disabled) [ 0.481146] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1 [ 0.489658] cpuidle: using governor ladder [ 0.494483] cpuidle: using governor menu [ 0.499750] Feroceon L2: Enabling L2 [ 0.504021] Feroceon L2: Cache support initialised. [ 0.514149] No ATAGs? [ 2.568514] random: fast init done [ 4.964230] alg: No test for lzo-rle (lzo-rle-generic) [ 4.970387] alg: No test for lzo-rle (lzo-rle-scomp) [ 5.148948] raid6: int32x8 gen() 171 MB/s [ 5.318721] raid6: int32x8 xor() 116 MB/s [ 5.488539] raid6: int32x4 gen() 175 MB/s [ 5.658733] raid6: int32x4 xor() 115 MB/s [ 5.828630] raid6: int32x2 gen() 186 MB/s [ 5.998728] raid6: int32x2 xor() 132 MB/s [ 6.168854] raid6: int32x1 gen() 150 MB/s [ 6.338694] raid6: int32x1 xor() 99 MB/s [ 6.343631] raid6: using algorithm int32x2 gen() 186 MB/s [ 6.349698] raid6: .... xor() 132 MB/s, rmw enabled [ 6.355242] raid6: using intx1 recovery algorithm [ 6.360809] vgaarb: loaded [ 6.364577] SCSI subsystem initialized [ 6.369195] libata version 3.00 loaded. [ 6.369385] usbcore: registered new interface driver usbfs [ 6.375581] usbcore: registered new interface driver hub [ 6.381639] usbcore: registered new device driver usb [ 6.387479] pps_core: LinuxPPS API ver. 1 registered [ 6.393127] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.402925] PTP clock support registered [ 6.408739] clocksource: Switched to clocksource orion_clocksource [ 7.190657] VFS: Disk quotas dquot_6.6.0 [ 7.195318] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 7.209877] NET: Registered protocol family 2 [ 7.215527] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 7.223920] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 7.231600] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 7.238636] TCP: Hash tables configured (established 2048 bind 2048) [ 7.245743] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 7.252272] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 7.259383] NET: Registered protocol family 1 [ 7.264878] RPC: Registered named UNIX socket transport module. [ 7.271524] RPC: Registered udp transport module. [ 7.276897] RPC: Registered tcp transport module. [ 7.282278] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.289391] PCI: CLS 0 bytes, default 32 [ 7.294153] Trying to unpack rootfs image as initramfs... [ 7.916734] Freeing initrd memory: 9488K [ 7.921769] NetWinder Floating Point Emulator V0.97 (double precision) [ 7.929946] Initialise system trusted keyrings [ 7.935094] Key type blacklist registered [ 7.940004] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 7.947173] zbud: loaded [ 7.951253] NFS: Registering the id_resolver key type [ 7.956980] Key type id_resolver registered [ 7.961893] Key type id_legacy registered [ 7.966578] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 7.973960] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.981205] jffs2: version 2.2. (NAND) (SUMMARY) \xc2\xa9 2001-2006 Red Hat, Inc. [ 7.989093] fuse: init (API version 7.31) [ 7.994060] orangefs_debugfs_init: called with debug mask: :none: :0: [ 8.001324] orangefs_init: module version upstream loaded [ 8.007384] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 8.028538] async_tx: api initialized (async) [ 8.033654] Key type asymmetric registered [ 8.038419] Asymmetric key parser 'x509' registered [ 8.044053] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 8.053260] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.062831] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.129377] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.138894] mv_xor f1060900.xor: Marvell shared XOR driver [ 8.199351] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.209112] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 8.217064] printk: console [ttyS0] disabled [ 8.222108] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A [ 8.231781] printk: console [ttyS0] enabled [ 8.241553] printk: bootconsole [earlycon0] disabled [ 8.258473] loop: module loaded [ 8.262606] sata_mv f1080000.sata: version 1.28 [ 8.262821] sata_mv f1080000.sata: slots 32 ports 2 [ 8.270406] scsi host0: sata_mv [ 8.274688] scsi host1: sata_mv [ 8.278802] ata1: SATA max UDMA/133 irq 34 [ 8.283617] ata2: SATA max UDMA/133 irq 34 [ 8.289794] m25p80 spi0.0: mx25l8005 (1024 Kbytes) [ 8.295341] 3 fixed-partitions partitions found on MTD device spi0.0 [ 8.302456] Creating 3 MTD partitions on "spi0.0": [ 8.307967] 0x000000000000-0x00000007e000 : "u-boot" [ 8.313663] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only [ 8.323651] 0x00000007e000-0x00000007f000 : "u-boot env2" [ 8.329800] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only [ 8.341124] 0x00000007f000-0x000000080000 : "u-boot env" [ 8.347158] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only [ 8.359315] libphy: Fixed MDIO Bus: probed [ 8.364704] libphy: orion_mdio_bus: probed [ 8.380136] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 8.388022] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 8.395791] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9 [ 8.405417] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.412728] ehci-pci: EHCI PCI platform driver [ 8.417927] ehci-orion: EHCI orion driver [ 8.422822] orion-ehci f1050000.ehci: EHCI Host Controller [ 8.429069] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 8.437584] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000 [ 8.468763] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.475680] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 8.484703] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.492666] usb usb1: Product: EHCI Host Controller [ 8.498259] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 8.505615] usb usb1: SerialNumber: f1050000.ehci [ 8.511514] hub 1-0:1.0: USB hub found [ 8.516006] hub 1-0:1.0: 1 port detected [ 8.521203] usbcore: registered new interface driver usb-storage [ 8.528223] mousedev: PS/2 mouse device common for all mice [ 8.534988] rtc-mv f1010300.rtc: registered as rtc0 [ 8.540744] i2c /dev entries driver [ 8.546067] device-mapper: uevent: version 1.0.3 [ 8.551700] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 8.561197] device-mapper: multipath round-robin: version 1.2.0 loaded [ 8.568486] device-mapper: multipath queue-length: version 0.2.0 loaded [ 8.575867] device-mapper: multipath service-time: version 0.3.0 loaded [ 8.583299] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 8.590149] device-mapper: raid: Loading target version 1.14.0 [ 8.597778] hidraw: raw HID events driver (C) Jiri Kosina [ 8.604182] drop_monitor: Initializing network drop monitor service [ 8.611441] NET: Registered protocol family 17 [ 8.616807] Key type dns_resolver registered [ 8.622717] registered taskstats version 1 [ 8.627532] Loading compiled-in X.509 certificates [ 8.633216] zswap: loaded using pool lzo/zbud [ 8.705797] Key type big_key registered [ 8.741311] Key type encrypted registered [ 8.747637] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T23:33:31 UTC (1588894411) [ 8.788775] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 8.800301] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133 [ 8.806687] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.820927] ata1.00: configured for UDMA/133 [ 8.836306] scsi 0:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5 [ 8.845853] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 8.854771] sd 0:0:0:0: [sda] Write Protect is off [ 8.860337] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8.860428] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.888766] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.920223] sda: sda1 sda2 sda3 [ 8.925480] sd 0:0:0:0: [sda] Attached SCSI disk [ 9.190115] ata2: SATA link down (SStatus 0 SControl F300) [ 9.209544] Freeing unused kernel memory: 1024K [ 9.215171] Checked W+X mappings: passed, no W+X pages found [ 9.221568] Run /init as init process [ 14.078760] usb 1-1: device descriptor read/64, error -110 [ 14.399713] usb 1-1: New USB device found, idVendor=abcd, idProduct=1234, bcdDevice= 1.00 [ 14.408634] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 14.416524] usb 1-1: Product: UDisk [ 14.421699] usb 1-1: Manufacturer: General [ 14.426596] usb 1-1: SerialNumber: 1804251030306948643714 [ 14.434481] usb-storage 1-1:1.0: USB Mass Storage device detected [ 14.441690] scsi host2: usb-storage 1-1:1.0 [ 14.457439] usbcore: registered new interface driver uas [ 15.449664] scsi 2:0:0:0: Direct-Access General UDisk 5.00 PQ: 0 ANSI: 2 [ 15.462763] sd 2:0:0:0: [sdb] 7782400 512-byte logical blocks: (3.98 GB/3.71 GiB) [ 15.476376] sd 2:0:0:0: [sdb] Write Protect is off [ 15.481964] sd 2:0:0:0: [sdb] Mode Sense: 0b 00 00 08 [ 15.482360] sd 2:0:0:0: [sdb] No Caching mode page found [ 15.488397] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 15.549449] sdb: sdb1 [ 15.560629] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 31.550008] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 31.597838] systemd-udevd[376]: Using default interface naming scheme 'v240'. [ 31.727392] systemd-udevd[376]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.831268] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 31.873697] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 32.008974] adt7475 0-002e: ADT7473 device, revision 0 [ 32.014838] adt7475 0-002e: Optional features: fan4 pwm2 [ 32.047500] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 32.093038] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 32.172136] orion_wdt: Initial timeout 21 sec [ 32.192984] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 32.215891] marvell-cesa f1030000.crypto: CESA device successfully registered [ 32.296701] random: crng init done [ 32.418333] systemd-udevd[375]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 98.001793] NET: Registered protocol family 10 [ 98.008019] Segment Routing with IPv6 root@debian:~#
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 06:49PM |
Admin Registered: 13 years ago Posts: 18,543 |
It is strange that your serial console output was stopped until 8 seconds into the boot. Information from those 8 seconds are quite valuable!
I think your HDD rootfs is not good. But before recreating it, let's try booting agai none more time.
Note: at this point after you interrupt serial console, the USB drive should be unplugged. Only the HDD rootfs is pugged in.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I think your HDD rootfs is not good. But before recreating it, let's try booting agai none more time.
Note: at this point after you interrupt serial console, the USB drive should be unplugged. Only the HDD rootfs is pugged in.
setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial' setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x02100000 /boot/uInitrd' setenv bootcmd 'run bootcmd_sata; bootm 0x00800000 0x02100000'And then
boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 07:01PM |
Registered: 3 years ago Posts: 14 |
no not coming
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x02100000 /boot/uInitrd'
Marvell>> setenv bootcmd 'run bootcmd_sata; bootm 0x00800000 0x02100000'
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
4988970 bytes read
9713936 bytes read
## Booting image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:44:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4988906 Bytes = 4.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:45:35 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 8.231766][ T1] printk: console [ttyS0] enabled
[ 8.241544][ T1] printk: bootconsole [earlycon0] disabled
[ 8.258482][ T1] loop: module loaded
[ 8.262825][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 8.270410][ T1] scsi host0: sata_mv
[ 8.274695][ T1] scsi host1: sata_mv
[ 8.278815][ T1] ata1: SATA max UDMA/133 irq 34
[ 8.283625][ T1] ata2: SATA max UDMA/133 irq 34
[ 8.289810][ T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 8.295347][ T1] 3 fixed-partitions partitions found on MTD device spi0.0
[ 8.302463][ T1] Creating 3 MTD partitions on "spi0.0":
[ 8.307974][ T1] 0x000000000000-0x00000007e000 : "u-boot"
[ 8.313671][ T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[ 8.323665][ T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[ 8.329818][ T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[ 8.341142][ T1] 0x00000007f000-0x000000080000 : "u-boot env"
[ 8.347175][ T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[ 8.359331][ T1] libphy: Fixed MDIO Bus: probed
[ 8.364720][ T1] libphy: orion_mdio_bus: probed
[ 8.380093][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.387980][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[ 8.395744][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[ 8.405372][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.412685][ T1] ehci-pci: EHCI PCI platform driver
[ 8.417883][ T1] ehci-orion: EHCI orion driver
[ 8.422776][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 8.429023][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 8.437532][ T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 8.468748][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 8.475665][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 8.484684][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.492649][ T1] usb usb1: Product: EHCI Host Controller
[ 8.498241][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[ 8.505597][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 8.511498][ T1] hub 1-0:1.0: USB hub found
[ 8.515987][ T1] hub 1-0:1.0: 1 port detected
[ 8.521180][ T1] usbcore: registered new interface driver usb-storage
[ 8.528210][ T1] mousedev: PS/2 mouse device common for all mice
[ 8.534978][ T1] rtc-mv f1010300.rtc: registered as rtc0
[ 8.540734][ T1] i2c /dev entries driver
[ 8.546058][ T1] device-mapper: uevent: version 1.0.3
[ 8.551689][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 8.561178][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 8.568467][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 8.575849][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 8.583281][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 8.590130][ T1] device-mapper: raid: Loading target version 1.14.0
[ 8.597750][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 8.604156][ T1] drop_monitor: Initializing network drop monitor service
[ 8.611424][ T1] NET: Registered protocol family 17
[ 8.616793][ T1] Key type dns_resolver registered
[ 8.622695][ T1] registered taskstats version 1
[ 8.627505][ T1] Loading compiled-in X.509 certificates
[ 8.633485][ T1] zswap: loaded using pool lzo/zbud
[ 8.705826][ T1] Key type big_key registered
[ 8.741249][ T1] Key type encrypted registered
[ 8.747454][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T23:56:54 UTC (1588895814)
[ 8.788760][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 8.800251][ T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[ 8.806635][ T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.820868][ T112] ata1.00: configured for UDMA/133
[ 8.836243][ T7] scsi 0:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5
[ 8.845798][ T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 8.854706][ T116] sd 0:0:0:0: [sda] Write Protect is off
[ 8.860363][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.927665][ T116] sda: sda1 sda2 sda3
[ 8.932933][ T116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.190107][ T114] ata2: SATA link down (SStatus 0 SControl F300)
[ 9.209339][ T1] Freeing unused kernel memory: 1024K
[ 9.214970][ T1] Checked W+X mappings: passed, no W+X pages found
[ 9.221368][ T1] Run /init as init process
Loading, please wait...
Starting version 241
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
[ 38.852402][ C0] random: crng init done
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device. Common problems:
- Boot args (cat /proc/cmdline)
- Check rootdelay= (did the system wait long enough?)
- Missing modules (cat /proc/modules; ls /dev)
ALERT! LABEL=rootfs does not exist. Dropping to a shell!
BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 07:08PM |
Admin Registered: 13 years ago Posts: 18,543 |
OK. So now it is time to recreate your rootfs. Your rsync probably did not pick up all the necessary files.
And remember that your should use a single EXT3 partition on the HDD.
Basically, bring your USB to another box, create the tarball. Copy that tarball to the USB rootfs itself. Boot with USB, and then restore the tarball to the HDD, while logging in as root.
https://forum.doozan.com/read.php?2,12096,24034#msg-24034
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
And remember that your should use a single EXT3 partition on the HDD.
Basically, bring your USB to another box, create the tarball. Copy that tarball to the USB rootfs itself. Boot with USB, and then restore the tarball to the HDD, while logging in as root.
https://forum.doozan.com/read.php?2,12096,24034#msg-24034
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 07:13PM |
Registered: 3 years ago Posts: 14 |
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 07:39PM |
Admin Registered: 13 years ago Posts: 18,543 |
Kicum,
If you HDD is large, then partition it now to your liking. The first partition should be the rootfs, label it as rootfs, and it should be EXT3. And don't use swap partition, use a swap file (create it after booted successfully).
The single partition approach is to eliminate any potential problem in booting. But it is not absolutely required.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
If you HDD is large, then partition it now to your liking. The first partition should be the rootfs, label it as rootfs, and it should be EXT3. And don't use swap partition, use a swap file (create it after booted successfully).
The single partition approach is to eliminate any potential problem in booting. But it is not absolutely required.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix2- ng freezes the install stage May 07, 2020 09:24PM |
Registered: 3 years ago Posts: 14 |
Thanks a lot Bodhi !!! I did according to your instructions and everything worked out! You are a real Guru!
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x02100000 /boot/uInitrd'
Marvell>> setenv bootcmd 'run bootcmd_sata; bootm 0x00800000 0x02100000'
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST32000542AS Firm: CC38 Ser#: 5XW27CR4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
4988970 bytes read
9713936 bytes read
## Booting image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:44:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4988906 Bytes = 4.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2020-05-05 22:45:35 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 8.231773][ T1] printk: console [ttyS0] enabled
[ 8.241552][ T1] printk: bootconsole [earlycon0] disabled
[ 8.258495][ T1] loop: module loaded
[ 8.262850][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 8.270426][ T1] scsi host0: sata_mv
[ 8.274709][ T1] scsi host1: sata_mv
[ 8.278823][ T1] ata1: SATA max UDMA/133 irq 34
[ 8.283634][ T1] ata2: SATA max UDMA/133 irq 34
[ 8.289819][ T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 8.295357][ T1] 3 fixed-partitions partitions found on MTD device spi0.0
[ 8.302473][ T1] Creating 3 MTD partitions on "spi0.0":
[ 8.307983][ T1] 0x000000000000-0x00000007e000 : "u-boot"
[ 8.313680][ T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[ 8.323680][ T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[ 8.329834][ T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[ 8.341159][ T1] 0x00000007f000-0x000000080000 : "u-boot env"
[ 8.347193][ T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[ 8.359351][ T1] libphy: Fixed MDIO Bus: probed
[ 8.364736][ T1] libphy: orion_mdio_bus: probed
[ 8.380269][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.388161][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[ 8.395921][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[ 8.405550][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.412857][ T1] ehci-pci: EHCI PCI platform driver
[ 8.418058][ T1] ehci-orion: EHCI orion driver
[ 8.422953][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 8.429199][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 8.437707][ T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 8.468764][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 8.475673][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 8.484695][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.492658][ T1] usb usb1: Product: EHCI Host Controller
[ 8.498251][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[ 8.505606][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 8.511501][ T1] hub 1-0:1.0: USB hub found
[ 8.515997][ T1] hub 1-0:1.0: 1 port detected
[ 8.521189][ T1] usbcore: registered new interface driver usb-storage
[ 8.528219][ T1] mousedev: PS/2 mouse device common for all mice
[ 8.534986][ T1] rtc-mv f1010300.rtc: registered as rtc0
[ 8.540744][ T1] i2c /dev entries driver
[ 8.546064][ T1] device-mapper: uevent: version 1.0.3
[ 8.551688][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 8.561180][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 8.568468][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 8.575848][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 8.583281][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 8.590130][ T1] device-mapper: raid: Loading target version 1.14.0
[ 8.597770][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 8.604173][ T1] drop_monitor: Initializing network drop monitor service
[ 8.611436][ T1] NET: Registered protocol family 17
[ 8.616805][ T1] Key type dns_resolver registered
[ 8.622715][ T1] registered taskstats version 1
[ 8.627522][ T1] Loading compiled-in X.509 certificates
[ 8.633660][ T1] zswap: loaded using pool lzo/zbud
[ 8.706182][ T1] Key type big_key registered
[ 8.741760][ T1] Key type encrypted registered
[ 8.747966][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-08T02:11:18 UTC (1588903878)
[ 8.788775][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 8.800269][ T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[ 8.806652][ T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.820884][ T112] ata1.00: configured for UDMA/133
[ 8.836263][ T7] scsi 0:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5
[ 8.845817][ T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 8.854736][ T116] sd 0:0:0:0: [sda] Write Protect is off
[ 8.860391][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.917603][ T116] sda: sda1 sda2
[ 8.922283][ T116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.190120][ T114] ata2: SATA link down (SStatus 0 SControl F300)
[ 9.209360][ T1] Freeing unused kernel memory: 1024K
[ 9.214988][ T1] Checked W+X mappings: passed, no W+X pages found
[ 9.221394][ T1] Run /init as init process
Loading, please wait...
Starting version 241
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 15118/1310720 files, 342872/5242880 blocks
done.
[ 20.779075][ T190] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 20.801260][ T190] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...[ 23.116715][ T373] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[ 23.162341][ T371] systemd-udevd[371]: Using default interface naming scheme 'v240'.
[ 23.287047][ T371] systemd-udevd[371]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 23.343087][ T392] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 23.360610][ T372] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[ 23.467353][ T372] watchdog: f1020300.watchdog-timer: falling back to default timeout (21)
[ 23.509762][ T392] adt7475 0-002e: ADT7473 device, revision 0
[ 23.515627][ T392] adt7475 0-002e: Optional features: fan4 pwm2
[ 23.580762][ T372] orion_wdt: Initial timeout 21 sec
[ 23.655165][ T373] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 23.750465][ T377] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 23.836937][ T377] systemd-udevd[377]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[ 24.968932][ T590] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now che[ 25.648558][ C0] random: crng init done
ck all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:d0:b8:1d:7d:a9
Sending on LPF/eth0/00:d0:b8:1d:7d:a9
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 1
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
done.
[....] Starting RPC port mapper daemon: rpcbind[ 89.509043][ T1196] NET: Registered protocol family 10
[ 89.516317][ T1196] Segment Routing with IPv6
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1337 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1364 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 10 debian ttyS0
debian login:
