Welcome! Log In Create A New Profile

Advanced

Iomega ix2- ng freezes the install stage

Posted by Kicum 
Iomega ix2- ng freezes the install stage
May 05, 2020 05:06AM
Hello! I have an old Iomega ix2 -ng. I decided to install Debian on it, following the instructions of the respected Bodhi. Prepared a flash drive, inserted, launched. But when the kernel boot phase comes in, everything freezes, the indicator goes out.

      __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27GCY
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000'
Marvell>> setenv bootcmd 'run usb_boot'
Marvell>> setenv usb_root 'LABEL=rootfs'
Marvell>> setenv rootdelay 10
Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
.................................................................................................................................................................................................................
.......................................................................

4975125 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
.................................................................................................................................................................................................................
....................................................................................................................................................................................................................................................................................................................................................................................................................
....
............................................................................................................................

9713936 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-05   0:41:36 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4975061 Bytes =  4.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2019-08-25   2:22:50 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
autoload=no
ethact=egiga0
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
mfgmodel=ix2
preroot_ver=0.0.2
fw_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
ethaddr=00:D0:B8:1D:7D:A9
serialNo=EUAC0200L4
modelname=31997200
serialno=0,01MuwrcB7lyFn/sJNvS+/yyCI0wXkRlFrlEB8OuEQQvFMHkASe8dp3t2E/zFs3Nt1O,EUAC0200L4,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.0.3/download_runin.sh
pre_path_conf=IX2/1.0.3/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.0.3
image_multi=yes
console=console=ttyS0,115200
initrd_size=0x2f0000
loadaddr=0x2000000
serial_number=5563Y01001G152001BBJ0A1
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000
bootfile=zImage
usb_root=sdb1
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext3
TFTFTP! tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm
TFTP!=tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm 0x00800000 0x01100000;
filesize=18af10
fileaddr=800000
gatewayip=192.168.1.1
netmask=255.255.255.0
ipaddr=192.168.1.123
serverip=192.168.1.181
bootargs_console=console=ttyS0,115200 root=/dev/sdb1
bootcmd_sata=ide reset; ext2load ide 0:1 0x01100000 /uInitrd; ext2load ide 0:1 0x00800000 /uImage
bootcmd=setenv bootargs $(bootargs_console); run bootcmd_sata; bootm 0x00800000 0x01100000
bootcmd_usb=usb start; ext2load usb 0:1 0x800000 /uImage; ext2load usb 0:1 0x1100000 /uInitrd; bootm 0x800000 0x1100000;
arcNumber=11
bootargs=console=ttyS0,115200 root=/dev/sdb1
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no

Environment size: 2857/4091 bytes
Marvell>>

Can someone help me?
Re: Iomega ix2- ng freezes the install stage
May 05, 2020 04:08PM
Hi, as these units have the old uboot you need to append the dtb to the kernel. These are the instructions under '4b' in Bodhi's guide;

4b. Boot with DTB file embedded in the kernel image (no U-Boot envs changes are needed if your system already booting on USB or HDD). Again, this step 4b is for stock U-Boot only.

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box.

Generate the uImage and uInitrd (the kernel files vmlinuz-5.6.5-kirkwood-tld-1 and initrd.img-5.6.5-kirkwood-tld-1 were generated by dpkg in Step 3):
cd /boot
mv uImage uImage.orig
mv uInitrd uInitrd.orig
cp -a zImage-5.6.5-kirkwood-tld-1  zImage.fdt
cat dts/kirkwood-goflexnet.dtb  >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n 5.6.5-kirkwood-tld-1 -d zImage.fdt  uImage
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.6.5-kirkwood-tld-1 -d initrd.img-5.6.5-kirkwood-tld-1 uInitrd

Use the IX2 dtb instead of the goflex and it should boot without issue.
Re: Iomega ix2- ng freezes the install stage
May 05, 2020 04:44PM
J,

It looks like the uImage had a DTB appended to it.

## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-05   0:41:36 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4975061 Bytes =  4.7 MB

But let Kicum response first, before we can speculate further.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 05, 2020 07:24PM
Thanks jdwl101. Fixed DTB. Loading gone
Re: Iomega ix2- ng freezes the install stage
May 05, 2020 07:49PM
Kicum,

Did you append a wrong DTB before?

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 05, 2020 08:19PM
Yes. I just copied the command without looking:)
Re: Iomega ix2- ng freezes the install stage
May 05, 2020 08:39PM
Kicum Wrote:
-------------------------------------------------------
> Yes. I just copied the command without looking:)

Cool! Because the booting behavior indicated that there was a DTB, just one for the wrong box!

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 05, 2020 08:43PM
Congrats, glad to see its running
Re: Iomega ix2- ng freezes the install stage
May 06, 2020 04:20PM
Hi! Now I have a new problem. I can not boot from the hdd. I also made rootfs on the hdd as a USB flash drive. I can’t configure the environment.

      __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


** Unable to read "/uInitrd" from ide 0:1 **

** Unable to read "/uImage" from ide 0:1 **
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>


Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
autoload=no
ethact=egiga0
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
mfgmodel=ix2
preroot_ver=0.0.2
fw_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
ethaddr=00:D0:B8:1D:7D:A9
serialNo=EUAC0200L4
modelname=31997200
serialno=0,01MuwrcB7lyFn/sJNvS+/yyCI0wXkRlFrlEB8OuEQQvFMHkASe8dp3t2E/zFs3Nt1O,EUAC0200L4,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.0.3/download_runin.sh
pre_path_conf=IX2/1.0.3/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.0.3
image_multi=yes
console=console=ttyS0,115200
initrd_size=0x2f0000
loadaddr=0x2000000
serial_number=5563Y01001G152001BBJ0A1
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000
bootfile=zImage
usb_root=sdb1
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext3
TFTFTP! tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm
TFTP!=tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm 0x00800000 0x01100000;
filesize=18af10
fileaddr=800000
gatewayip=192.168.1.1
netmask=255.255.255.0
ipaddr=192.168.1.123
serverip=192.168.1.181
bootargs_console=console=ttyS0,115200 root=/dev/sdb1
bootcmd_sata=ide reset; ext2load ide 0:1 0x01100000 /uInitrd; ext2load ide 0:1 0x00800000 /uImage
bootcmd=setenv bootargs $(bootargs_console); run bootcmd_sata; bootm 0x00800000 0x01100000
bootcmd_usb=usb start; ext2load usb 0:1 0x800000 /uImage; ext2load usb 0:1 0x1100000 /uInitrd; bootm 0x800000 0x1100000;
arcNumber=11
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
bootargs=console=ttyS0,115200 root=/dev/sdb1

Environment size: 2857/4091 bytes

root@debian:~# fdisk -l
Disk /dev/mtdblock0: 504 KiB, 516096 bytes, 1008 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock1: 4 KiB, 4096 bytes, 8 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock2: 4 KiB, 4096 bytes, 8 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/sda: 1.8 TiB, 2000398934016 bytes, 3907029168 sectors
Disk model: ST32000542AS
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x0cf2e517

Device         Boot   Start        End    Sectors  Size Id Type
/dev/sda1          2048    2099199    2097152    1G 83 Linux
/dev/sda2       2099200    3147775    1048576  512M 82 Linux swap / Solaris
/dev/sda3       3147776 3907028991 3903881216  1.8T 83 Linux


Disk /dev/sdb: 3.7 GiB, 3984588800 bytes, 7782400 sectors
Disk model: UDisk
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x90909090

Device     Boot Start     End Sectors Size Id Type
/dev/sdb1        2048 2099199 2097152   1G 83 Linux
Re: Iomega ix2- ng freezes the install stage
May 06, 2020 04:35PM
Kicum,

You need to change the SATA boot:
setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 06, 2020 04:45PM
I've changed . But now freezes


         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


9713936 bytes read

4976325 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-06   3:27:34 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4976261 Bytes =  4.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2020-05-06   3:27:13 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Re: Iomega ix2- ng freezes the install stage
May 06, 2020 04:47PM
Looks like it is the same problem as before with USB rootfs.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 06, 2020 05:17PM
I rewrote the new rootfs on hdd. Same thing happens

      __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


9713936 bytes read

4976325 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-06  22:05:45 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4976261 Bytes =  4.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2020-05-06  22:06:10 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...



Edited 1 time(s). Last edit at 05/06/2020 05:47PM by Kicum.
Re: Iomega ix2- ng freezes the install stage
May 06, 2020 06:18PM
Maybe I should boot under USB and prepare hdd from there?
Re: Iomega ix2- ng freezes the install stage
May 06, 2020 10:35PM
Kicum Wrote:
-------------------------------------------------------
> Maybe I should boot under USB and prepare hdd from
> there?

Good idea! you can either:

- Boot with USB, prepare the HDD and then run rsync to copy all the files over.

- Bringthe USB drive to another Linux computer, and then backup to a tarball, bring it back and restore to the HDD (I would do this, since it will create a backup for the USB rootfs that you can keep to recreate it again).

https://forum.doozan.com/read.php?2,12096,24034#msg-24034

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 04:26AM
Hi,

I suspect that the stock unboot needs the initrd loaded higher. The ix2-dl will crash unless you load higher.

Try
'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 04:43AM
> Try
> 'ext2load usb 0:1 0x2100000 /boot/uInitrd'

Right! That's need to be done to boot with stock u-boot.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 11:51AM
Hello! I booted the system from a usb flash drive. deleted old partitions. Created a new formatted boot partition in ext 2.
Then the
rsync -aAXv --exclude={"/dev/*","/proc/*","/sys/*","/tmp/*","/run/*","/mnt/*"} / /mnt/sda
copied the rootfs section.
Reboot
root@debian:/# cd /mnt/sda1
root@debian:/mnt/sda1# ls
.                                                 dev         media  run   usr
..                                                etc         mnt    sbin  var
Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2  home        opt    srv
bin                                               lib         proc   sys
boot                                              lost+found  root   tmp
root@debian:/mnt/sda1# cd ..
root@debian:/mnt# umount /mnt/sda1
root@debian:/mnt# reboot

Broadcast message from root@debian (ttyS0) (Thu May  7 09:22:37 2020):

INIT: Se[info] Using makefile-style concurrent boot in runlevel 6.
[ ok ] Stopping hotplug events dispatcher: systemd-udevd.
[ ok ] Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[....] Stopping busybox' klogd implementation: klogd1397 (klogd)
Stopped klogd (pid 1397).
. ok
[....] Stopping busybox' syslogd implementation: syslogd1370 (syslogd)
. ok
[ ok ] Stopping NFS kernel daemon: mountd nfsd.
[ ok ] Unexporting directories for NFS kernel daemon....
[ ok ] Asking all remaining processes to terminate...done.
[ ok ] All processes ended within 1 seconds...done.
[ ok ] Stopping NFS common utilities: idmapd statd.
[info] Saving the system clock.
[info] Hardware Clock updated to Thu May  7 09:22:42 PDT 2020.
[ ok ] Stopping RPC port mapper daemon: rpcbind.
[....] Deconfiguring network interfaces...Removed stale PID file
Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:1d:7d:a9
Sending on   LPF/eth0/00:d0:b8:1d:7d:a9
Sending on   Socket/fallback
DHCPRELEASE of 192.168.1.34 on eth0 to 192.168.1.1 port 67
send_packet: Network is unreachable
send_packet: please consult README file regarding broadcast address.
dhclient.c:2878: Failed to send 300 byte long packet over fallback interface.
done.
[ ok ] Saving random seed...done.
[....] Will now unmount temporary filesystems:umount: /tmp unmounted
. ok
[ ok ] Will now deactivate swap:.
[ ok ] Mounting root filesystem read-only...done.
[info] Will now restart.
[11978.629893][ T2215] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[11978.638341][ T2215] reboot: Restarting system

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


** Unable to read "/uInitrd" from ide 0:1 **

** Unable to read "/uImage" from ide 0:1 **
## Booting image at 00800000 ...
Bad Magic Number
Marvell>> reset

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x01100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


9713936 bytes read

4988970 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:44:03 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4988906 Bytes =  4.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:45:35 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...
What to do in this case?



Edited 1 time(s). Last edit at 05/07/2020 03:27PM by Kicum.
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 04:57PM
Try

setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x02100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage'
setenv bootcmd 'setenv bootargs $(bootargs_console) earlyprintk=serial; run bootcmd_sata; bootm 0x00800000 0x02100000'
printenv
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 05:30PM
go loading, only then it goes here

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:                                                                                          5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x02100000 /boot/uIni                                                                             trd; ext2load ide 0:1 0x00800000 /boot/uImage'
Marvell>> setenv bootcmd 'setenv bootargs $(bootargs_console) earlyprintk=serial; run bootcmd_sata; bootm 0x00800000 0x02100000'
Marvell>> printenv
Unknown command 'зк▒printenv' - try 'help'
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
autoload=no
ethact=egiga0
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
mfgmodel=ix2
preroot_ver=0.0.2
fw_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
ethaddr=00:D0:B8:1D:7D:A9
serialNo=EUAC0200L4
modelname=31997200
serialno=0,01MuwrcB7lyFn/sJNvS+/yyCI0wXkRlFrlEB8OuEQQvFMHkASe8dp3t2E/zFs3Nt1O,EUAC0200L4,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.0.3/download_runin.sh
pre_path_conf=IX2/1.0.3/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.0.3
image_multi=yes
console=console=ttyS0,115200
initrd_size=0x2f0000
loadaddr=0x2000000
serial_number=5563Y01001G152001BBJ0A1
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000
bootfile=zImage
usb_root=sdb1
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext3
TFTFTP! tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm
TFTP!=tftpboot 0x01100000 Initrd;tftpboot 0x00800000 zImage;bootm 0x00800000 0x01100000;
filesize=18af10
fileaddr=800000
gatewayip=192.168.1.1
netmask=255.255.255.0
ipaddr=192.168.1.123
serverip=192.168.1.181
bootargs_console=console=ttyS0,115200 root=/dev/sdb1
bootcmd_usb=usb start; ext2load usb 0:1 0x800000 /uImage; ext2load usb 0:1 0x1100000 /uInitrd; bootm 0x800000 0x1100000;
arcNumber=11
bootargs=console=ttyS0,115200 root=/dev/sdb1
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
bootcmd_sata=ide reset; ext2load ide 0:1 0x02100000 /boot/uInitrd; ext2load ide 0:1 0x00800000 /boot/uImage
bootcmd=setenv bootargs $(bootargs_console) earlyprintk=serial; run bootcmd_sata; bootm 0x00800000 0x02100000

Environment size: 2886/4091 bytes
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


9713936 bytes read

4988970 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:44:03 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4988906 Bytes =  4.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:45:35 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    8.231471][    T1] printk: console [ttyS0] enabled
[    8.241241][    T1] printk: bootconsole [earlycon0] disabled
[    8.258195][    T1] loop: module loaded
[    8.262548][    T1] sata_mv f1080000.sata: slots 32 ports 2
[    8.270133][    T1] scsi host0: sata_mv
[    8.274408][    T1] scsi host1: sata_mv
[    8.278521][    T1] ata1: SATA max UDMA/133 irq 34
[    8.283333][    T1] ata2: SATA max UDMA/133 irq 34
[    8.289522][    T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    8.295058][    T1] 3 fixed-partitions partitions found on MTD device spi0.0
[    8.302172][    T1] Creating 3 MTD partitions on "spi0.0":
[    8.307683][    T1] 0x000000000000-0x00000007e000 : "u-boot"
[    8.313379][    T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[    8.323383][    T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[    8.329535][    T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[    8.340870][    T1] 0x00000007f000-0x000000080000 : "u-boot env"
[    8.346901][    T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[    8.359067][    T1] libphy: Fixed MDIO Bus: probed
[    8.364456][    T1] libphy: orion_mdio_bus: probed
[    8.379991][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.387878][    T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[    8.395641][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[    8.405265][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.412577][    T1] ehci-pci: EHCI PCI platform driver
[    8.417775][    T1] ehci-orion: EHCI orion driver
[    8.422669][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[    8.428917][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    8.437424][    T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    8.468452][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    8.475365][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    8.484385][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.492349][    T1] usb usb1: Product: EHCI Host Controller
[    8.497942][    T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[    8.505297][    T1] usb usb1: SerialNumber: f1050000.ehci
[    8.511195][    T1] hub 1-0:1.0: USB hub found
[    8.515689][    T1] hub 1-0:1.0: 1 port detected
[    8.520886][    T1] usbcore: registered new interface driver usb-storage
[    8.527903][    T1] mousedev: PS/2 mouse device common for all mice
[    8.534674][    T1] rtc-mv f1010300.rtc: registered as rtc0
[    8.540436][    T1] i2c /dev entries driver
[    8.545762][    T1] device-mapper: uevent: version 1.0.3
[    8.551389][    T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    8.560880][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    8.568165][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    8.575549][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    8.582979][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    8.589829][    T1] device-mapper: raid: Loading target version 1.14.0
[    8.597457][    T1] hidraw: raw HID events driver (C) Jiri Kosina
[    8.603856][    T1] drop_monitor: Initializing network drop monitor service
[    8.611121][    T1] NET: Registered protocol family 17
[    8.616484][    T1] Key type dns_resolver registered
[    8.622134][    T1] registered taskstats version 1
[    8.626943][    T1] Loading compiled-in X.509 certificates
[    8.633375][    T1] zswap: loaded using pool lzo/zbud
[    8.706033][    T1] Key type big_key registered
[    8.741668][    T1] Key type encrypted registered
[    8.747878][    T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T22:23:33 UTC (1588890213)
[    8.788462][  T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    8.799960][  T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[    8.806342][  T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    8.820571][  T112] ata1.00: configured for UDMA/133
[    8.835951][    T7] scsi 0:0:0:0: Direct-Access     ATA      ST32000542AS     CC38 PQ: 0 ANSI: 5
[    8.845508][  T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    8.854430][  T116] sd 0:0:0:0: [sda] Write Protect is off
[    8.860094][  T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.921310][  T116]  sda: sda1 sda2 sda3
[    8.926562][  T116] sd 0:0:0:0: [sda] Attached SCSI disk
[    9.189808][  T114] ata2: SATA link down (SStatus 0 SControl F300)
[    9.209047][    T1] Freeing unused kernel memory: 1024K
[    9.214679][    T1] Checked W+X mappings: passed, no W+X pages found
[    9.221084][    T1] Run /init as init process
Loading, please wait...
Starting version 241
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device.  Common problems:
 - Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
 - Missing modules (cat /proc/modules; ls /dev)
ALERT!  /dev/sdb1 does not exist.  Dropping to a shell!


BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash)
Enter 'help' for a list of built-in commands.

(initramfs)

Re: Iomega ix2- ng freezes the install stage
May 07, 2020 05:39PM
Kicum,

Boot with USB like you did before

Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000'
Marvell>> setenv bootcmd 'run usb_boot'
Marvell>> setenv usb_root 'LABEL=rootfs'
Marvell>> setenv rootdelay 10
Marvell>> boot

And post the entire serial console log here (make sure that it does not get cut off on the right side).

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 05:55PM

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:                                                                                          5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>>
Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000'
Marvell>> setenv bootcmd 'run usb_boot'
Marvell>> setenv usb_root 'LABEL=rootfs'
Marvell>> setenv rootdelay 10
Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
........................................................................

4988970 bytes read
.
...
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
....................................................................................................................................................................................................................................................................................................................................................................................................................
....
............................................................................................................................

9713936 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:44:03 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4988906 Bytes =  4.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:45:35 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    8.231807][    T1] printk: console [ttyS0] enabled
[    8.241587][    T1] printk: bootconsole [earlycon0] disabled
[    8.258523][    T1] loop: module loaded
[    8.262871][    T1] sata_mv f1080000.sata: slots 32 ports 2
[    8.270452][    T1] scsi host0: sata_mv
[    8.274730][    T1] scsi host1: sata_mv
[    8.278847][    T1] ata1: SATA max UDMA/133 irq 34
[    8.283657][    T1] ata2: SATA max UDMA/133 irq 34
[    8.289842][    T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    8.295380][    T1] 3 fixed-partitions partitions found on MTD device spi0.0
[    8.302497][    T1] Creating 3 MTD partitions on "spi0.0":
[    8.308007][    T1] 0x000000000000-0x00000007e000 : "u-boot"
[    8.313703][    T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[    8.323700][    T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[    8.329849][    T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[    8.341177][    T1] 0x00000007f000-0x000000080000 : "u-boot env"
[    8.347207][    T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[    8.359368][    T1] libphy: Fixed MDIO Bus: probed
[    8.364765][    T1] libphy: orion_mdio_bus: probed
[    8.380184][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.388071][    T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[    8.395842][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[    8.405467][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.412777][    T1] ehci-pci: EHCI PCI platform driver
[    8.417976][    T1] ehci-orion: EHCI orion driver
[    8.422872][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[    8.429118][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    8.437623][    T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    8.468767][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    8.475687][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    8.484709][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.492673][    T1] usb usb1: Product: EHCI Host Controller
[    8.498265][    T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[    8.505620][    T1] usb usb1: SerialNumber: f1050000.ehci
[    8.511522][    T1] hub 1-0:1.0: USB hub found
[    8.516011][    T1] hub 1-0:1.0: 1 port detected
[    8.521209][    T1] usbcore: registered new interface driver usb-storage
[    8.528233][    T1] mousedev: PS/2 mouse device common for all mice
[    8.535000][    T1] rtc-mv f1010300.rtc: registered as rtc0
[    8.540758][    T1] i2c /dev entries driver
[    8.546085][    T1] device-mapper: uevent: version 1.0.3
[    8.551713][    T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    8.561206][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    8.568492][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    8.575872][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    8.583304][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    8.590154][    T1] device-mapper: raid: Loading target version 1.14.0
[    8.597787][    T1] hidraw: raw HID events driver (C) Jiri Kosina
[    8.604189][    T1] drop_monitor: Initializing network drop monitor service
[    8.611453][    T1] NET: Registered protocol family 17
[    8.616818][    T1] Key type dns_resolver registered
[    8.622722][    T1] registered taskstats version 1
[    8.627529][    T1] Loading compiled-in X.509 certificates
[    8.633219][    T1] zswap: loaded using pool lzo/zbud
[    8.705818][    T1] Key type big_key registered
[    8.741523][    T1] Key type encrypted registered
[    8.747858][    T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T22:53:04 UTC (1588891984)
[    8.788779][  T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    8.800307][  T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[    8.806694][  T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    8.820933][  T112] ata1.00: configured for UDMA/133
[    8.836314][    T7] scsi 0:0:0:0: Direct-Access     ATA      ST32000542AS     CC38 PQ: 0 ANSI: 5
[    8.845862][  T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    8.854776][  T116] sd 0:0:0:0: [sda] Write Protect is off
[    8.860433][  T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.888771][   T15] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    8.922019][  T116]  sda: sda1 sda2 sda3
[    8.927288][  T116] sd 0:0:0:0: [sda] Attached SCSI disk
[    9.190120][  T114] ata2: SATA link down (SStatus 0 SControl F300)
[    9.209553][    T1] Freeing unused kernel memory: 1024K
[    9.215185][    T1] Checked W+X mappings: passed, no W+X pages found
[    9.221593][    T1] Run /init as init process
Loading, please wait...
Starting version 241
[   14.078763][   T15] usb 1-1: device descriptor read/64, error -110
[   14.399751][   T15] usb 1-1: New USB device found, idVendor=abcd, idProduct=1234, bcdDevice= 1.00
[   14.408675][   T15] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   14.416566][   T15] usb 1-1: Product: UDisk
[   14.421741][   T15] usb 1-1: Manufacturer: General
[   14.426637][   T15] usb 1-1: SerialNumber: 1804251030306948643714
[   14.434521][   T15] usb-storage 1-1:1.0: USB Mass Storage device detected
[   14.441726][   T15] scsi host2: usb-storage 1-1:1.0
[   14.458099][  T169] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
[   15.449704][  T116] scsi 2:0:0:0: Direct-Access     General  UDisk            5.00 PQ: 0 ANSI: 2
[   15.462801][   T23] sd 2:0:0:0: [sdb] 7782400 512-byte logical blocks: (3.98 GB/3.71 GiB)
[   15.476417][   T23] sd 2:0:0:0: [sdb] Write Protect is off
[   15.482399][   T23] sd 2:0:0:0: [sdb] No Caching mode page found
[   15.488438][   T23] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   15.549487][   T23]  sdb: sdb1
[   15.560667][   T23] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
fsck: error 2 (No such file or directory) while executing fsck.ext2 for /dev/sdb1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[....] Synthesizing the initial hotplug events (devices)...[   31.571483][  T374] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ ok                                                       done.
[   31.612349][  T384] systemd-udevd[384]: Using default interface naming scheme 'v240'.
[....] Waiting for /dev to be fully populated...[   31.752546][  T384] systemd-udevd[384]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   31.851378][  T385] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[   31.946624][  T377] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   31.981851][  T385] watchdog: f1020300.watchdog-timer: falling back to default timeout (21)
[   32.092509][  T385] orion_wdt: Initial timeout 21 sec
[   32.112663][  T377] adt7475 0-002e: ADT7473 device, revision 0
[   32.152871][  T386] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   32.207611][  T377] adt7475 0-002e: Optional features: fan4 pwm2
[   32.223892][  T374] marvell-cesa f1030000.crypto: CESA device successfully registered
[   32.239155][  T386] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   32.292800][    C0] random: crng init done
[   32.390870][  T386] systemd-udevd[386]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[....] Will now check root file system:fsck from util-linux 2.33.1
[/sbin/fsck.ext2 (1) -- /] fsck.ext2 -y -C0 /dev/sdb1
e2fsck 1.44.5 (15-Dec-2018)
rootfs: clean, 15113/65536 files, 210180/262144 blocks
. ok
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:1d:7d:a9
Sending on   LPF/eth0/00:d0:b8:1d:7d:a9
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
done.
[....] Starting RPC port mapper daemon: rpcbind[   97.950358][ T1226] NET: Registered protocol family 10
[   97.956857][ T1226] Segment Routing with IPv6
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1367 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1394 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 10 debian ttyS0

debian login:

Re: Iomega ix2- ng freezes the install stage
May 07, 2020 06:12PM
Log in and then post dmesg output:

dmesg

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 06:37PM
Debian GNU/Linux 10 debian ttyS0

debian login: root
Password:
Last login: Thu May  7 16:24:10 PDT 2020 on ttyS0
Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Lenovo IX2-ng
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 65536
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 234780K/262144K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 27364K reserved, 0K cma-reserved)
[    0.000000] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000006] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.008509] Switching to timer-based delay loop, resolution 5ns
[    0.015663] Console: colour dummy device 80x30
[    0.020843] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.032046] pid_max: default: 32768 minimum: 301
[    0.037608] LSM: Security Framework initializing
[    0.043068] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.050385] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.058786] *** VALIDATE proc ***
[    0.062972] *** VALIDATE cgroup1 ***
[    0.067229] *** VALIDATE cgroup2 ***
[    0.071576] CPU: Testing write buffer coherency: ok
[    0.078433] Setting up static identity map for 0x100000 - 0x100058
[    0.085554] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[    0.091592] rcu: Hierarchical SRCU implementation.
[    0.099511] devtmpfs: initialized
[    0.108598] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.119137] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.126111] xor: measuring software checksum speed
[    0.228532]    arm4regs  :  1446.000 MB/sec
[    0.328531]    8regs     :   868.000 MB/sec
[    0.428526]    32regs    :  1262.000 MB/sec
[    0.433382] xor: using function: arm4regs (1446.000 MB/sec)
[    0.439648] prandom: seed boundary self test passed
[    0.448337] prandom: 100 self tests passed
[    0.453132] pinctrl core: initialized pinctrl subsystem
[    0.460148] NET: Registered protocol family 16
[    0.465898] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.474086] audit: initializing netlink subsys (disabled)
[    0.481146] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1
[    0.489658] cpuidle: using governor ladder
[    0.494483] cpuidle: using governor menu
[    0.499750] Feroceon L2: Enabling L2
[    0.504021] Feroceon L2: Cache support initialised.
[    0.514149] No ATAGs?
[    2.568514] random: fast init done
[    4.964230] alg: No test for lzo-rle (lzo-rle-generic)
[    4.970387] alg: No test for lzo-rle (lzo-rle-scomp)
[    5.148948] raid6: int32x8  gen()   171 MB/s
[    5.318721] raid6: int32x8  xor()   116 MB/s
[    5.488539] raid6: int32x4  gen()   175 MB/s
[    5.658733] raid6: int32x4  xor()   115 MB/s
[    5.828630] raid6: int32x2  gen()   186 MB/s
[    5.998728] raid6: int32x2  xor()   132 MB/s
[    6.168854] raid6: int32x1  gen()   150 MB/s
[    6.338694] raid6: int32x1  xor()    99 MB/s
[    6.343631] raid6: using algorithm int32x2 gen() 186 MB/s
[    6.349698] raid6: .... xor() 132 MB/s, rmw enabled
[    6.355242] raid6: using intx1 recovery algorithm
[    6.360809] vgaarb: loaded
[    6.364577] SCSI subsystem initialized
[    6.369195] libata version 3.00 loaded.
[    6.369385] usbcore: registered new interface driver usbfs
[    6.375581] usbcore: registered new interface driver hub
[    6.381639] usbcore: registered new device driver usb
[    6.387479] pps_core: LinuxPPS API ver. 1 registered
[    6.393127] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    6.402925] PTP clock support registered
[    6.408739] clocksource: Switched to clocksource orion_clocksource
[    7.190657] VFS: Disk quotas dquot_6.6.0
[    7.195318] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    7.209877] NET: Registered protocol family 2
[    7.215527] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[    7.223920] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    7.231600] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    7.238636] TCP: Hash tables configured (established 2048 bind 2048)
[    7.245743] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    7.252272] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    7.259383] NET: Registered protocol family 1
[    7.264878] RPC: Registered named UNIX socket transport module.
[    7.271524] RPC: Registered udp transport module.
[    7.276897] RPC: Registered tcp transport module.
[    7.282278] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    7.289391] PCI: CLS 0 bytes, default 32
[    7.294153] Trying to unpack rootfs image as initramfs...
[    7.916734] Freeing initrd memory: 9488K
[    7.921769] NetWinder Floating Point Emulator V0.97 (double precision)
[    7.929946] Initialise system trusted keyrings
[    7.935094] Key type blacklist registered
[    7.940004] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    7.947173] zbud: loaded
[    7.951253] NFS: Registering the id_resolver key type
[    7.956980] Key type id_resolver registered
[    7.961893] Key type id_legacy registered
[    7.966578] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    7.973960] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    7.981205] jffs2: version 2.2. (NAND) (SUMMARY)  \xc2\xa9 2001-2006 Red Hat, Inc.
[    7.989093] fuse: init (API version 7.31)
[    7.994060] orangefs_debugfs_init: called with debug mask: :none: :0:
[    8.001324] orangefs_init: module version upstream loaded
[    8.007384] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled
[    8.028538] async_tx: api initialized (async)
[    8.033654] Key type asymmetric registered
[    8.038419] Asymmetric key parser 'x509' registered
[    8.044053] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    8.053260] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    8.062831] mv_xor f1060800.xor: Marvell shared XOR driver
[    8.129377] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    8.138894] mv_xor f1060900.xor: Marvell shared XOR driver
[    8.199351] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    8.209112] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    8.217064] printk: console [ttyS0] disabled
[    8.222108] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[    8.231781] printk: console [ttyS0] enabled
[    8.241553] printk: bootconsole [earlycon0] disabled
[    8.258473] loop: module loaded
[    8.262606] sata_mv f1080000.sata: version 1.28
[    8.262821] sata_mv f1080000.sata: slots 32 ports 2
[    8.270406] scsi host0: sata_mv
[    8.274688] scsi host1: sata_mv
[    8.278802] ata1: SATA max UDMA/133 irq 34
[    8.283617] ata2: SATA max UDMA/133 irq 34
[    8.289794] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    8.295341] 3 fixed-partitions partitions found on MTD device spi0.0
[    8.302456] Creating 3 MTD partitions on "spi0.0":
[    8.307967] 0x000000000000-0x00000007e000 : "u-boot"
[    8.313663] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[    8.323651] 0x00000007e000-0x00000007f000 : "u-boot env2"
[    8.329800] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[    8.341124] 0x00000007f000-0x000000080000 : "u-boot env"
[    8.347158] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[    8.359315] libphy: Fixed MDIO Bus: probed
[    8.364704] libphy: orion_mdio_bus: probed
[    8.380136] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.388022] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[    8.395791] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[    8.405417] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.412728] ehci-pci: EHCI PCI platform driver
[    8.417927] ehci-orion: EHCI orion driver
[    8.422822] orion-ehci f1050000.ehci: EHCI Host Controller
[    8.429069] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    8.437584] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    8.468763] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    8.475680] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    8.484703] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.492666] usb usb1: Product: EHCI Host Controller
[    8.498259] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[    8.505615] usb usb1: SerialNumber: f1050000.ehci
[    8.511514] hub 1-0:1.0: USB hub found
[    8.516006] hub 1-0:1.0: 1 port detected
[    8.521203] usbcore: registered new interface driver usb-storage
[    8.528223] mousedev: PS/2 mouse device common for all mice
[    8.534988] rtc-mv f1010300.rtc: registered as rtc0
[    8.540744] i2c /dev entries driver
[    8.546067] device-mapper: uevent: version 1.0.3
[    8.551700] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    8.561197] device-mapper: multipath round-robin: version 1.2.0 loaded
[    8.568486] device-mapper: multipath queue-length: version 0.2.0 loaded
[    8.575867] device-mapper: multipath service-time: version 0.3.0 loaded
[    8.583299] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    8.590149] device-mapper: raid: Loading target version 1.14.0
[    8.597778] hidraw: raw HID events driver (C) Jiri Kosina
[    8.604182] drop_monitor: Initializing network drop monitor service
[    8.611441] NET: Registered protocol family 17
[    8.616807] Key type dns_resolver registered
[    8.622717] registered taskstats version 1
[    8.627532] Loading compiled-in X.509 certificates
[    8.633216] zswap: loaded using pool lzo/zbud
[    8.705797] Key type big_key registered
[    8.741311] Key type encrypted registered
[    8.747637] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T23:33:31 UTC (1588894411)
[    8.788775] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    8.800301] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[    8.806687] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    8.820927] ata1.00: configured for UDMA/133
[    8.836306] scsi 0:0:0:0: Direct-Access     ATA      ST32000542AS     CC38 PQ: 0 ANSI: 5
[    8.845853] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    8.854771] sd 0:0:0:0: [sda] Write Protect is off
[    8.860337] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    8.860428] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.888766] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    8.920223]  sda: sda1 sda2 sda3
[    8.925480] sd 0:0:0:0: [sda] Attached SCSI disk
[    9.190115] ata2: SATA link down (SStatus 0 SControl F300)
[    9.209544] Freeing unused kernel memory: 1024K
[    9.215171] Checked W+X mappings: passed, no W+X pages found
[    9.221568] Run /init as init process
[   14.078760] usb 1-1: device descriptor read/64, error -110
[   14.399713] usb 1-1: New USB device found, idVendor=abcd, idProduct=1234, bcdDevice= 1.00
[   14.408634] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   14.416524] usb 1-1: Product: UDisk
[   14.421699] usb 1-1: Manufacturer: General
[   14.426596] usb 1-1: SerialNumber: 1804251030306948643714
[   14.434481] usb-storage 1-1:1.0: USB Mass Storage device detected
[   14.441690] scsi host2: usb-storage 1-1:1.0
[   14.457439] usbcore: registered new interface driver uas
[   15.449664] scsi 2:0:0:0: Direct-Access     General  UDisk            5.00 PQ: 0 ANSI: 2
[   15.462763] sd 2:0:0:0: [sdb] 7782400 512-byte logical blocks: (3.98 GB/3.71 GiB)
[   15.476376] sd 2:0:0:0: [sdb] Write Protect is off
[   15.481964] sd 2:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[   15.482360] sd 2:0:0:0: [sdb] No Caching mode page found
[   15.488397] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   15.549449]  sdb: sdb1
[   15.560629] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   31.550008] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   31.597838] systemd-udevd[376]: Using default interface naming scheme 'v240'.
[   31.727392] systemd-udevd[376]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   31.831268] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   31.873697] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[   32.008974] adt7475 0-002e: ADT7473 device, revision 0
[   32.014838] adt7475 0-002e: Optional features: fan4 pwm2
[   32.047500] watchdog: f1020300.watchdog-timer: falling back to default timeout (21)
[   32.093038] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   32.172136] orion_wdt: Initial timeout 21 sec
[   32.192984] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   32.215891] marvell-cesa f1030000.crypto: CESA device successfully registered
[   32.296701] random: crng init done
[   32.418333] systemd-udevd[375]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   98.001793] NET: Registered protocol family 10
[   98.008019] Segment Routing with IPv6
root@debian:~#

Re: Iomega ix2- ng freezes the install stage
May 07, 2020 06:49PM
It is strange that your serial console output was stopped until 8 seconds into the boot. Information from those 8 seconds are quite valuable!

I think your HDD rootfs is not good. But before recreating it, let's try booting agai none more time.

Note: at this point after you interrupt serial console, the USB drive should be unplugged. Only the HDD rootfs is pugged in.

setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x02100000 /boot/uInitrd'
setenv bootcmd 'run bootcmd_sata; bootm 0x00800000 0x02100000'
And then

boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 07:01PM
no not coming

    __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x02100000 /boot/uInitrd'
Marvell>> setenv bootcmd 'run bootcmd_sata; bootm 0x00800000 0x02100000'
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


4988970 bytes read

9713936 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:44:03 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4988906 Bytes =  4.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:45:35 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    8.231766][    T1] printk: console [ttyS0] enabled
[    8.241544][    T1] printk: bootconsole [earlycon0] disabled
[    8.258482][    T1] loop: module loaded
[    8.262825][    T1] sata_mv f1080000.sata: slots 32 ports 2
[    8.270410][    T1] scsi host0: sata_mv
[    8.274695][    T1] scsi host1: sata_mv
[    8.278815][    T1] ata1: SATA max UDMA/133 irq 34
[    8.283625][    T1] ata2: SATA max UDMA/133 irq 34
[    8.289810][    T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    8.295347][    T1] 3 fixed-partitions partitions found on MTD device spi0.0
[    8.302463][    T1] Creating 3 MTD partitions on "spi0.0":
[    8.307974][    T1] 0x000000000000-0x00000007e000 : "u-boot"
[    8.313671][    T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[    8.323665][    T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[    8.329818][    T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[    8.341142][    T1] 0x00000007f000-0x000000080000 : "u-boot env"
[    8.347175][    T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[    8.359331][    T1] libphy: Fixed MDIO Bus: probed
[    8.364720][    T1] libphy: orion_mdio_bus: probed
[    8.380093][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.387980][    T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[    8.395744][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[    8.405372][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.412685][    T1] ehci-pci: EHCI PCI platform driver
[    8.417883][    T1] ehci-orion: EHCI orion driver
[    8.422776][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[    8.429023][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    8.437532][    T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    8.468748][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    8.475665][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    8.484684][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.492649][    T1] usb usb1: Product: EHCI Host Controller
[    8.498241][    T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[    8.505597][    T1] usb usb1: SerialNumber: f1050000.ehci
[    8.511498][    T1] hub 1-0:1.0: USB hub found
[    8.515987][    T1] hub 1-0:1.0: 1 port detected
[    8.521180][    T1] usbcore: registered new interface driver usb-storage
[    8.528210][    T1] mousedev: PS/2 mouse device common for all mice
[    8.534978][    T1] rtc-mv f1010300.rtc: registered as rtc0
[    8.540734][    T1] i2c /dev entries driver
[    8.546058][    T1] device-mapper: uevent: version 1.0.3
[    8.551689][    T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    8.561178][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    8.568467][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    8.575849][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    8.583281][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    8.590130][    T1] device-mapper: raid: Loading target version 1.14.0
[    8.597750][    T1] hidraw: raw HID events driver (C) Jiri Kosina
[    8.604156][    T1] drop_monitor: Initializing network drop monitor service
[    8.611424][    T1] NET: Registered protocol family 17
[    8.616793][    T1] Key type dns_resolver registered
[    8.622695][    T1] registered taskstats version 1
[    8.627505][    T1] Loading compiled-in X.509 certificates
[    8.633485][    T1] zswap: loaded using pool lzo/zbud
[    8.705826][    T1] Key type big_key registered
[    8.741249][    T1] Key type encrypted registered
[    8.747454][    T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-07T23:56:54 UTC (1588895814)
[    8.788760][  T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    8.800251][  T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[    8.806635][  T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    8.820868][  T112] ata1.00: configured for UDMA/133
[    8.836243][    T7] scsi 0:0:0:0: Direct-Access     ATA      ST32000542AS     CC38 PQ: 0 ANSI: 5
[    8.845798][  T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    8.854706][  T116] sd 0:0:0:0: [sda] Write Protect is off
[    8.860363][  T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.927665][  T116]  sda: sda1 sda2 sda3
[    8.932933][  T116] sd 0:0:0:0: [sda] Attached SCSI disk
[    9.190107][  T114] ata2: SATA link down (SStatus 0 SControl F300)
[    9.209339][    T1] Freeing unused kernel memory: 1024K
[    9.214970][    T1] Checked W+X mappings: passed, no W+X pages found
[    9.221368][    T1] Run /init as init process
Loading, please wait...
Starting version 241
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
[   38.852402][    C0] random: crng init done
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device.  Common problems:
 - Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
 - Missing modules (cat /proc/modules; ls /dev)
ALERT!  LABEL=rootfs does not exist.  Dropping to a shell!


BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash)
Enter 'help' for a list of built-in commands.

(initramfs)

Re: Iomega ix2- ng freezes the install stage
May 07, 2020 07:08PM
OK. So now it is time to recreate your rootfs. Your rsync probably did not pick up all the necessary files.

And remember that your should use a single EXT3 partition on the HDD.

Basically, bring your USB to another box, create the tarball. Copy that tarball to the USB rootfs itself. Boot with USB, and then restore the tarball to the HDD, while logging in as root.

https://forum.doozan.com/read.php?2,12096,24034#msg-24034

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 07:13PM
Only one partition on the whole HDD?
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 07:39PM
Kicum,

If you HDD is large, then partition it now to your liking. The first partition should be the rootfs, label it as rootfs, and it should be EXT3. And don't use swap partition, use a swap file (create it after booted successfully).

The single partition approach is to eliminate any potential problem in booting. But it is not absolutely required.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Iomega ix2- ng freezes the install stage
May 07, 2020 09:24PM
Thanks a lot Bodhi !!! I did according to your instructions and everything worked out! You are a real Guru!

  __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial'
Marvell>> setenv bootcmd_sata 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x02100000 /boot/uInitrd'
Marvell>> setenv bootcmd 'run bootcmd_sata; bootm 0x00800000 0x02100000'
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST32000542AS                             Firm: CC38     Ser#:             5XW27CR4
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)


4988970 bytes read

9713936 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:44:03 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4988906 Bytes =  4.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2020-05-05  22:45:35 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    8.231773][    T1] printk: console [ttyS0] enabled
[    8.241552][    T1] printk: bootconsole [earlycon0] disabled
[    8.258495][    T1] loop: module loaded
[    8.262850][    T1] sata_mv f1080000.sata: slots 32 ports 2
[    8.270426][    T1] scsi host0: sata_mv
[    8.274709][    T1] scsi host1: sata_mv
[    8.278823][    T1] ata1: SATA max UDMA/133 irq 34
[    8.283634][    T1] ata2: SATA max UDMA/133 irq 34
[    8.289819][    T1] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    8.295357][    T1] 3 fixed-partitions partitions found on MTD device spi0.0
[    8.302473][    T1] Creating 3 MTD partitions on "spi0.0":
[    8.307983][    T1] 0x000000000000-0x00000007e000 : "u-boot"
[    8.313680][    T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[    8.323680][    T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[    8.329834][    T1] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only
[    8.341159][    T1] 0x00000007f000-0x000000080000 : "u-boot env"
[    8.347193][    T1] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
[    8.359351][    T1] libphy: Fixed MDIO Bus: probed
[    8.364736][    T1] libphy: orion_mdio_bus: probed
[    8.380269][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.388161][    T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[    8.395921][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:1d:7d:a9
[    8.405550][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.412857][    T1] ehci-pci: EHCI PCI platform driver
[    8.418058][    T1] ehci-orion: EHCI orion driver
[    8.422953][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[    8.429199][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    8.437707][    T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    8.468764][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    8.475673][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    8.484695][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.492658][    T1] usb usb1: Product: EHCI Host Controller
[    8.498251][    T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[    8.505606][    T1] usb usb1: SerialNumber: f1050000.ehci
[    8.511501][    T1] hub 1-0:1.0: USB hub found
[    8.515997][    T1] hub 1-0:1.0: 1 port detected
[    8.521189][    T1] usbcore: registered new interface driver usb-storage
[    8.528219][    T1] mousedev: PS/2 mouse device common for all mice
[    8.534986][    T1] rtc-mv f1010300.rtc: registered as rtc0
[    8.540744][    T1] i2c /dev entries driver
[    8.546064][    T1] device-mapper: uevent: version 1.0.3
[    8.551688][    T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    8.561180][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    8.568468][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    8.575848][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    8.583281][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    8.590130][    T1] device-mapper: raid: Loading target version 1.14.0
[    8.597770][    T1] hidraw: raw HID events driver (C) Jiri Kosina
[    8.604173][    T1] drop_monitor: Initializing network drop monitor service
[    8.611436][    T1] NET: Registered protocol family 17
[    8.616805][    T1] Key type dns_resolver registered
[    8.622715][    T1] registered taskstats version 1
[    8.627522][    T1] Loading compiled-in X.509 certificates
[    8.633660][    T1] zswap: loaded using pool lzo/zbud
[    8.706182][    T1] Key type big_key registered
[    8.741760][    T1] Key type encrypted registered
[    8.747966][    T1] rtc-mv f1010300.rtc: setting system clock to 2020-05-08T02:11:18 UTC (1588903878)
[    8.788775][  T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    8.800269][  T112] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133
[    8.806652][  T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    8.820884][  T112] ata1.00: configured for UDMA/133
[    8.836263][    T7] scsi 0:0:0:0: Direct-Access     ATA      ST32000542AS     CC38 PQ: 0 ANSI: 5
[    8.845817][  T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    8.854736][  T116] sd 0:0:0:0: [sda] Write Protect is off
[    8.860391][  T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.917603][  T116]  sda: sda1 sda2
[    8.922283][  T116] sd 0:0:0:0: [sda] Attached SCSI disk
[    9.190120][  T114] ata2: SATA link down (SStatus 0 SControl F300)
[    9.209360][    T1] Freeing unused kernel memory: 1024K
[    9.214988][    T1] Checked W+X mappings: passed, no W+X pages found
[    9.221394][    T1] Run /init as init process
Loading, please wait...
Starting version 241
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 15118/1310720 files, 342872/5242880 blocks
done.
[   20.779075][  T190] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   20.801260][  T190] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...[   23.116715][  T373] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   23.162341][  T371] systemd-udevd[371]: Using default interface naming scheme 'v240'.
[   23.287047][  T371] systemd-udevd[371]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   23.343087][  T392] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   23.360610][  T372] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[   23.467353][  T372] watchdog: f1020300.watchdog-timer: falling back to default timeout (21)
[   23.509762][  T392] adt7475 0-002e: ADT7473 device, revision 0
[   23.515627][  T392] adt7475 0-002e: Optional features: fan4 pwm2
[   23.580762][  T372] orion_wdt: Initial timeout 21 sec
[   23.655165][  T373] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   23.750465][  T377] marvell-cesa f1030000.crypto: CESA device successfully registered
[   23.836937][  T377] systemd-udevd[377]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[   24.968932][  T590] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now che[   25.648558][    C0] random: crng init done
ck all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:1d:7d:a9
Sending on   LPF/eth0/00:d0:b8:1d:7d:a9
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 1
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
done.
[....] Starting RPC port mapper daemon: rpcbind[   89.509043][ T1196] NET: Registered protocol family 10
[   89.516317][ T1196] Segment Routing with IPv6
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1337 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1364 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 10 debian ttyS0

debian login:

Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: