IconBIT IS608 Oxnas OX820 booting problem with kernel 4.14.x

Quote
Log into Debian,

Problem with MAC on Openwrt, no problems with MAC on Debian

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
OX820 # printenv
SET_dtb=fdt addr ${fdtaddr} ; fdt header
autoload=no
baudrate=115200
bootargs=root=LABEL=rootfs root=/dev/sda2
bootcmd=run ideboot
bootdelay=3
bootnew=bootm 60000000 - 61000000
bootold=bootm 60000000
console=console=ttyS0,115200n8
ethact=mii0
ethaddr=74:F0:6D:6A:1D:17
ext4_dtb=ext4load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb
ext4_ideboot=run ext4_uimage ; run ext4_dtb ; run SET_dtb ; run bootnew
ext4_uimage=ext4load ide 0:2 60000000 /boot/uImage
ext4_uinitrd=ext4load ide 0:2 0x60e00000 /boot/uInitrd
fdtaddr=61000000
filesize=2316
ideboot=run ext4_ideboot
idebootold=${loadold} ;${bootold}
imgaddr=60000000
ipaddr=10.0.0.71
keypressed=1
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
netcon=echo switch to net console;setenv stderr nc;setenv stdin nc;setenv stdout nc;echo switch to net console
preboot=run safeboot
serialcon=echo switch to serial console;setenv stderr serial;setenv stdin serial;setenv stdout serial;echo switch to serial console
stderr=serial
stdin=serial
stdout=serial
updboot=bootp;tftp 60000000 u-boot.img;ide write 60000000 400 400

Environment size: 1167/16380 bytes
OX820 # boot
3765068 bytes read in 598 ms (6 MiB/s)
8996 bytes read in 56 ms (156.3 KiB/s)
magic:                  0xd00dfeed
totalsize:              0x2324 (8996)
off_dt_struct:          0x38
off_dt_strings:         0x1fd8
off_mem_rsvmap:         0x28
version:                17
last_comp_version:      16
boot_cpuid_phys:        0x0
size_dt_strings:        0x34c
size_dt_struct:         0x1fa0
number mem_rsv:         0x0

## Booting kernel from Legacy Image at 60000000 ...
   Image Name:   ARM OpenWrt Linux-5.4.42
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3765004 Bytes = 3.6 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
   Booting using the fdt blob at 0x61000000
   Loading Kernel Image ... OK
   Loading Device Tree to 67e26000, end 67e2b323 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.42 (admin@runtu) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13374-2b92ee3)) #0 SMP Wed May 27 22:48:39 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 3
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x64000000
[    0.000000] percpu: Embedded 15 pages/cpu s29644 r8192 d23604 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: earlyprintk console=ttyS0,115200 root=/dev/sda2 rootfstype=ext4
[    0.000000] Bootloader command line not present
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 54360K/131072K available (6144K kernel code, 169K rwdata, 1372K rodata, 1024K init, 210K bss, 11176K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x2c0/0x4ec with crng_init=0
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000069] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000081] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000104] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000266] GIC: PPI13 is secure or misconfigured
[    0.000317] GIC: PPI13 is secure or misconfigured
[    0.000401] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.050416] pid_max: default: 32768 minimum: 301
[    0.050682] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.050705] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.052008] CPU: Testing write buffer coherency: ok
[    0.053757] Setting up static identity map for 0x60100000 - 0x6010005c
[    0.054010] rcu: Hierarchical SRCU implementation.
[    0.054635] smp: Bringing up secondary CPUs ...
[    0.055587] GIC: PPI13 is secure or misconfigured
[    0.110658] smp: Brought up 1 node, 2 CPUs
[    0.110689] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[    0.115425] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.115458] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.121812] pinctrl core: initialized pinctrl subsystem
[    0.122659] NET: Registered protocol family 16
[    0.126807] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.129100] cpuidle: using governor menu
[    0.129228] No ATAGs?
[    0.154078] SCSI subsystem initialized
[    0.154739] pps_core: LinuxPPS API ver. 1 registered
[    0.154752] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.154795] PTP clock support registered
[    0.155880] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.157199] thermal_sys: Registered thermal governor 'step_wise'
[    0.157557] NET: Registered protocol family 2
[    0.158320] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.158394] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.158428] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.158464] TCP: Hash tables configured (established 1024 bind 1024)
[    0.158615] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.158663] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.159057] NET: Registered protocol family 1
[    0.159111] PCI: CLS 0 bytes, default 32
[    0.160878] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.172800] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.175767] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.177702] printk: console [ttyS0] disabled
[    0.177858] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    0.609131] printk: console [ttyS0] enabled
[    0.629224] brd: module loaded
[    0.642488] loop: module loaded
[    0.647498] scsi host0: sata_oxnas
[    0.651427] ata1: SATA max UDMA/133 irq 57
[    0.656056] sata_oxnas: resetting SATA core
[    0.726182] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    0.734830] ONFI parameter recovery failed, aborting
[    0.739829] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    0.746191] nand: Hynix NAND 256MiB 3,3V 8-bit
[    0.750620] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.758192] Scanning device for bad blocks
[    0.788815] Bad eraseblock 324 at 0x000002880000
[    0.793451] Bad eraseblock 325 at 0x0000028a0000
[    0.938874] 5 fixed-partitions partitions found on MTD device 41000000.nand-controller
[    0.946787] Creating 5 MTD partitions on "41000000.nand-controller":
[    0.953118] 0x000000000000-0x000000040000 : "stage1"
[    0.959682] 0x000000040000-0x0000003c0000 : "u-boot"
[    0.966231] 0x0000003c0000-0x000000440000 : "u-boot-env"
[    0.973184] 0x000000440000-0x000000e00000 : "kernel"
[    0.979840] 0x000000e00000-0x000008000000 : "ubi"
[    0.987205] libphy: Fixed MDIO Bus: probed
[    0.992092] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[    0.998254] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    1.004067] oxnas-dwmac 40400000.ethernet: no reset control found
[    1.076264] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[    1.083212] oxnas-dwmac 40400000.ethernet:   DWMAC1000
[    1.088302] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    1.095577] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    1.102881] oxnas-dwmac 40400000.ethernet: COE Type 2
[    1.107939] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    1.114777] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    1.121095] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    1.127918] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    1.134499] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    1.140170] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.148014] oxnas-dwmac 40400000.ethernet: device MAC address ea:f8:07:b9:18:8f
[    1.165360] libphy: stmmac: probed
[    1.165931] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    1.168821] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.187604] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    1.202442] ledtrig-cpu: registered to indicate activity on CPUs
[    1.210076] NET: Registered protocol family 10
[    1.216166] Segment Routing with IPv6
[    1.219911] NET: Registered protocol family 17
[    1.230586] UBI error: no valid UBI magic found inside mtd4
[    1.236275] ata1.00: HPA detected: current 156299375, native 156301488
[    1.242808] ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
[    1.242818] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    1.291312] ata1.00: configured for UDMA/133
[    1.296312] scsi 0:0:0:0: Direct-Access     ATA      ST380815AS       C    PQ: 0 ANSI: 5
[    1.305681] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.306401] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    1.318822] sd 0:0:0:0: [sda] Write Protect is off
[    1.323822] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.356372]  sda: sda1 sda2 sda3
[    1.362055] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.373265] EXT4-fs (sda2): INFO: recovery required on readonly filesystem
[    1.380183] EXT4-fs (sda2): write access will be enabled during recovery
[    1.451210] EXT4-fs (sda2): recovery complete
[    1.489318] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[    1.497098] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[    1.505231] Freeing unused kernel memory: 1024K
[    1.510064] Run /sbin/init as init process
[    1.664350] init: Console is alive
[    1.771845] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    1.804848] usbcore: registered new interface driver usbfs
[    1.810485] usbcore: registered new interface driver hub
[    1.815987] usbcore: registered new device driver usb
[    1.822830] Button Hotplug driver version 0.4.1
[    1.830310] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.838604] ehci-fsl: Freescale EHCI Host controller driver
[    1.845294] ehci-platform: EHCI generic platform driver
[    2.055910] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    2.061424] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    2.069708] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    2.095930] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    2.103086] hub 1-0:1.0: USB hub found
[    2.107000] hub 1-0:1.0: 2 ports detected
[    2.116805] usbcore: registered new interface driver usb-storage
[    2.124011] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.133550] init: - preinit -
[    2.532254] random: jshn: uninitialized urandom read (4 bytes read)
[    2.577464] random: jshn: uninitialized urandom read (4 bytes read)
[    2.613939] random: jshn: uninitialized urandom read (4 bytes read)
[    2.647680] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211DN Gigabit Ethernet]
[    2.658734] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found
[    2.666193] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    2.674785] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[    2.681208] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.872314] mount_root: mounting /dev/root
[    6.886492] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    6.894924] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    6.895326] EXT4-fs (sda2): re-mounted. Opts: (null)
[    6.906529] mount_root: loading kmods from internal overlay
[    6.937077] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    6.946757] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    7.506186] block: attempting to load /etc/config/fstab
[    7.523947] block: extroot: not configured
[    7.531632] urandom-seed: Seeding with /etc/urandom.seed
[    7.582259] oxnas-dwmac 40400000.ethernet eth0: Link is Down
[    7.598848] procd: - early -
[    7.827484] urandom_read: 1 callbacks suppressed
[    7.827496] random: jshn: uninitialized urandom read (4 bytes read)
[    8.166054] procd: - ubus -
[    8.229437] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.236610] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.244587] procd: - init -
Please press Enter to activate this console.
[    8.854586] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.867261] urngd: v1.0.2 started.
[    8.970368] videodev: Linux video capture interface: v2.00
[    9.014858] usbcore: registered new interface driver ums-alauda
[    9.022648] random: crng init done
[    9.022735] usbcore: registered new interface driver ums-cypress
[    9.026127] random: 3 urandom warning(s) missed due to ratelimiting
[    9.042465] usbcore: registered new interface driver ums-datafab
[    9.050429] usbcore: registered new interface driver ums-freecom
[    9.063265] usbcore: registered new interface driver ums-isd200
[    9.087467] usbcore: registered new interface driver ums-jumpshot
[    9.095444] usbcore: registered new interface driver ums-karma
[    9.113167] usbcore: registered new interface driver ums-sddr09
[    9.132769] usbcore: registered new interface driver ums-sddr55
[    9.142036] usbcore: registered new interface driver ums-usbat
[    9.203207] xt_time: kernel timezone is -0000
[    9.267576] usbcore: registered new interface driver uvcvideo
[    9.273305] USB Video Class driver (1.1.1)
[    9.310671] kmodloader: done loading kernel modules from /etc/modules.d/*
[   13.253524] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211DN Gigabit Ethernet]
[   13.306042] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found
[   13.313428] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   13.322063] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[   13.328448] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode
[   13.344143] br-lan: port 1(eth0) entered blocking state
[   13.349460] br-lan: port 1(eth0) entered disabled state
[   13.355013] device eth0 entered promiscuous mode
[   17.526458] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   17.534899] br-lan: port 1(eth0) entered blocking state
[   17.540180] br-lan: port 1(eth0) entered forwarding state
[   17.547248] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.31.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r13374-2b92ee3
 -----------------------------------------------------
root@OpenWrt:/# fw_printenv
Warning: Bad CRC, using default environment
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=5
baudrate=115200
root@OpenWrt:/# ls -lart /boot
-rw-r--r--    1 root     root      15554100 May 31 00:13 uInitrd
-rw-r--r--    1 root     root       3765068 May 31 00:13 uImage
drwxr-xr-x    2 root     root          4096 May 31 00:13 dts
drwxrwxr-x   18 root     root          4096 May 31 00:13 ..
drwxr-xr-x    3 root     root          4096 May 31 00:13 .
root@OpenWrt:/# ls -lart /boot/dts
-rw-r--r--    1 root     root          8996 May 31 00:13 ox820-pogoplug-classic.dtb
drwxr-xr-x    3 root     root          4096 May 31 00:13 ..
drwxr-xr-x    2 root     root          4096 May 31 00:13 .
root@OpenWrt:/#

Edited 2 time(s). Last edit at 05/31/2020 07:21AM by sakatgg.

sakatgg,

I see. Unfortunately I don't have much experience with OpenWrt so cannot tell what's wrong right away. The u-boot you have on the HDD is basically the same as mine (shv built it using the source from my GitHub) so I don't think it is u-boot problem.

For now, you can work around this by specifying the MAC address inside /etc/network/interfaces.

=======

One thing seems wrong is the timestamp of the kernel files. They all the same!

-rw-r--r--    1 root     root          8996 May 31 00:13 ox820-pogoplug-classic.dtb

After you rebuilt kernel and DTB, and then copy the files you should use "cp -a" to preserve the timestamp, so later you can check to see if you have the wrong files.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

ARM Debian takes the MAC from sda1 /u-boot.env, and ARM Openwrt seems to be looking for the path from etc / fw_env.config

/dev/mtd2 0x0 0x2000 0x2000 1

Openwrt does not find it. I'm loading with sata, there is no mdX on sata

root @ OpenWrt: / # fw_printenv
Предупреждение: неверный CRC, используется среда по умолчанию
bootcmd = ВООТР; setenv bootargs root = / dev / nfs nfsroot = $ {serverip}: $ {rootpath} ip = $ {ipaddr}: $ {serverip}: $ {gatewayip}: $ {netmask}: $ {hostname} :: off; bootm
BootDelay = 5
боды = 115200

Quote
For now, you can work around this by specifying the MAC address inside /etc/network/interfaces.

Yes did so, added

/etc/network

	option macaddr '2A:C0:XX:XX:XX:XX'

Quote
After you rebuilt kernel and DTB, and then copy the files you should use "cp -a"

Ok



Edited 2 time(s). Last edit at 06/01/2020 09:57AM by sakatgg.

Quote

ARM Debian takes the MAC from sda1 /u-boot.env

Incorrect. That was the u-boot on HDD only.

In the normal case both Debian and OpenWrt look for the envs mtd in /etc/fw_env.config

Quote

Openwrt does not find it. I'm loading with sata, there is no mdX on sata

Correct. So fw_ennv cannot be used, unless we go further and make it appear there is an mtd0 and mtd1 on SATA (this u-boot does not use mtd2). This will not be worth the trouble (because you already have a work around).

So the problem is the params being passed from u-boot to kernel seems to be ignored by OpenWrt. This params is a block of memory that the kernel has access to. It usually has MAC address, memory size, and other info.

See if you can run this in u-boot:

bdinfo

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
OX820 # BDInfo
Unknown command 'BDInfo' - try 'help'
OX820 #

For my IconBIT IS608, the ox820-akitio profile is better suited, there is i2c there, the on and off button works.



Edited 1 time(s). Last edit at 06/01/2020 10:51PM by sakatgg.

> OX820 # BDInfo
> Unknown command 'BDInfo' - try 'help'
> OX820 #

lower case

bdinfo

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

SATA

U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  Boot device: SATA
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set
Bus 0: OK
  Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: ST380815AS Firm: 3.AAC  Ser#: 6QZ0M5Y2
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
NAND:  256 MiB
reading u-boot.env
In:    serial
Out:   serial
Err:   serial
Net:   mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot:  0
OX820 # bdinfo
arch_number = 0x00000480
boot_params = 0x60000100
DRAM bank   = 0x00000000
-> start    = 0x60000000
-> size     = 0x08000000
eth0name    = mii0
ethaddr     = 74:F0:6D:6A:1D:17
current eth = mii0
ip_addr     = 10.0.0.71
baudrate    = 115200 bps
TLB addr    = 0x67FF0000
relocaddr   = 0x67F2D000
reloc off   = 0x03F2D000
irq_sp      = 0x67E2CF48
sp start    = 0x67E2CF38
OX820 #

NAND

Stage-1 Bootloader Thu Jun  3 10:29:14 PDT 2010
Attempting to set PLLA to 700MHz ...
  plla_ctrl0 : 0x00000118
  plla_ctrl1 : 0x00380000
  plla_ctrl2 : 0x006F00D0
  plla_ctrl3 : 0x000000B0
PLLA Set

Setup memory, testing
Reading NAND, Image 0
Failed to correct error
  Hdr len: 0x0001AB60
  Hdr CRC: 0xE0B0E526
 read failed
Reading NAND, Image 1
  Hdr len: 0x0001AB60
  Hdr CRC: 0xE0B0E526
 OK


U-Boot 1.1.2 (Mar  2 2011 - 10:17:22)

U-Boot code: 60D00000 -> 60D1AB60  BSS: -> 60D1F218
RAM Configuration:
        Bank #0: 60000000 128 MB
SRAM Configuration:
        64KB at 0x50000000
NAND:256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0
$ bdinfo
arch_number = 0x00000480
env_t       = 0x00000000
boot_params = 0x60000100
DRAM bank   = 0x00000000
-> start    = 0x60000000
-> size     = 0x08000000
ethaddr     = 00:30:E0:00:00:01
ip_addr     = 192.168.50.100
baudrate    = 115200 bps
$

SATA

ethaddr     = 74:F0:6D:6A:1D:17

NAND

ethaddr     = 00:30:E0:00:00:01

The NAND MAC addr is correct (Oxford Semi NAS). But the SATA MAC addr is also OK (Azure Wave).

If OpenWrt worked correctly, then you should see the SATA MAC addr being used to assign to the NIC.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

On the native Fedora 12 firmware, a completely different MAC is the one that is indicated on the label on the NAS enclosure.

By the way, on the ox820-akitio profile, blue led works, blinks while downloading, and then glows.



Edited 1 time(s). Last edit at 06/02/2020 07:45AM by sakatgg.

sakatgg,

> On the native Fedora 12 firmware, a completely
> different MAC is the one that is indicated on the
> label on the NAS enclosure.

The one on the enclosure is the correct one to use.

>
> By the way, on the ox820-akitio profile, blue led
> works, blinks while downloading, and then glows.

Then this IconBIT is a clone of the Akitio, not the Pogoplug Classic. Do you have link that shows a picture of this box somewhere?

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

All these models are exact copies, the board, the case are the same, the design of the front panel is slightly different. They only have a different manufacturer’s label and software

AkiTio MyCloud Duo
iconBIT i-Stor iS608
FANTEC CL-35B2
Eminent EM4172



Edited 4 time(s). Last edit at 06/02/2020 08:13PM by sakatgg.

I see.

Then you should definitely use the Akitio DTB for booting. It is different from the Pogoplug V3 in LEDs configuration.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)