Re: Verbatim MediaShare 47490 December 21, 2020 01:21AM |
Registered: 3 years ago Posts: 26 |
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' saveenvboot from NAND?
Re: Verbatim MediaShare 47490 December 21, 2020 02:00AM |
Registered: 3 years ago Posts: 26 |
>Quote
uboot.2017.07-tld-1.pogo_e02.mtd0.kwb
Quote
uboot.2017.07-tld-1.iconnect.mtd0.kwb
root@xubuntu-System-Product-Name:/home/xubuntu/kwboot-tool# ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.iconnect.mtd0.kwb -p Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 1 % [......................................................................] ... 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:29:48 -0700) Iomega iConnect SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 256 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 4096 60084224 04cb3567-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 722 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4975179 bytes read in 1024 ms (4.6 MiB/s) loading uInitrd ... 9713936 bytes read in 940 ms (9.9 MiB/s) loading DTB /boot/dts/kirkwood-iconnect.dtb ... 11130 bytes read in 1169 ms (8.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-12-17 11:52:39 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4975115 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f1c6000, end 0fb098d0 ... OK Loading Device Tree to 0f1c0000, end 0f1c5b79 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000][ T0] Memory: 114320K/131072K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 16752K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008601][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015988][ T0] Console: colour dummy device 80x30 [ 0.021237][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032561][ T0] pid_max: default: 32768 minimum: 301 [ 0.038269][ T0] LSM: Security Framework initializing [ 0.043830][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.051239][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.060005][ T0] *** VALIDATE proc *** [ 0.064301][ T0] *** VALIDATE cgroup1 *** [ 0.068658][ T0] *** VALIDATE cgroup2 *** [ 0.073054][ T0] CPU: Testing write buffer coherency: ok [ 0.080436][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.087642][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.093848][ T1] rcu: Hierarchical SRCU implementation. [ 0.102613][ T1] devtmpfs: initialized [ 0.112200][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.122866][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.130020][ T1] xor: measuring software checksum speed [ 0.228625][ T1] arm4regs : 1083.600 MB/sec [ 0.328628][ T1] 8regs : 650.400 MB/sec [ 0.428627][ T1] 32regs : 945.600 MB/sec [ 0.433539][ T1] xor: using function: arm4regs (1083.600 MB/sec) [ 0.439875][ T1] prandom: seed boundary self test passed [ 0.449706][ T1] prandom: 100 self tests passed [ 0.454527][ T1] pinctrl core: initialized pinctrl subsystem [ 0.461982][ T1] NET: Registered protocol family 16 [ 0.467632][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.476126][ T1] audit: initializing netlink subsys (disabled) [ 0.483542][ T14] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1 [ 0.492179][ T1] cpuidle: using governor ladder [ 0.497072][ T1] cpuidle: using governor menu [ 0.502241][ T1] Feroceon L2: Enabling L2 [ 0.506570][ T1] Feroceon L2: Cache support initialised. [ 0.518200][ T1] No ATAGs? [ 2.568609][ C0] random: fast init done [ 6.483349][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 6.489909][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 6.668934][ T1] raid6: int32x8 gen() 127 MB/s [ 6.839029][ T1] raid6: int32x8 xor() 86 MB/s [ 7.008988][ T1] raid6: int32x4 gen() 129 MB/s [ 7.178880][ T1] raid6: int32x4 xor() 83 MB/s [ 7.348734][ T1] raid6: int32x2 gen() 132 MB/s [ 7.518913][ T1] raid6: int32x2 xor() 94 MB/s [ 7.689167][ T1] raid6: int32x1 gen() 100 MB/s [ 7.858881][ T1] raid6: int32x1 xor() 68 MB/s [ 7.863865][ T1] raid6: using algorithm int32x2 gen() 132 MB/s [ 7.870003][ T1] raid6: .... xor() 94 MB/s, rmw enabled [ 7.875514][ T1] raid6: using intx1 recovery algorithm [ 7.881211][ T1] vgaarb: loaded [ 7.885152][ T1] SCSI subsystem initialized [ 7.890139][ T1] usbcore: registered new interface driver usbfs [ 7.896397][ T1] usbcore: registered new interface driver hub [ 7.902568][ T1] usbcore: registered new device driver usb [ 7.908509][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.914220][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.924131][ T1] PTP clock support registered [ 7.930063][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.974409][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.979137][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.996730][ T1] NET: Registered protocol family 2 [ 9.002694][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 9.011184][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 9.018887][ T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 9.026026][ T1] TCP: Hash tables configured (established 1024 bind 1024) [ 9.033240][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 9.039816][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 9.047066][ T1] NET: Registered protocol family 1 [ 9.052818][ T1] RPC: Registered named UNIX socket transport module. [ 9.059464][ T1] RPC: Registered udp transport module. [ 9.064969][ T1] RPC: Registered tcp transport module. [ 9.070413][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.077581][ T1] PCI: CLS 0 bytes, default 32 [ 9.082599][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.091039][ T1] Initialise system trusted keyrings [ 9.096240][ T1] Key type blacklist registered [ 9.101238][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 9.108486][ T1] zbud: loaded [ 9.112925][ T1] NFS: Registering the id_resolver key type [ 9.118714][ T1] Key type id_resolver registered [ 9.123730][ T1] Key type id_legacy registered [ 9.128471][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.135926][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.143323][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.151356][ T1] fuse: init (API version 7.31) [ 9.156463][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.163854][ T1] orangefs_init: module version upstream loaded [ 9.169982][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 9.181754][ T1] async_tx: api initialized (async) [ 9.186842][ T1] Key type asymmetric registered [ 9.191720][ T1] Asymmetric key parser 'x509' registered [ 9.197369][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.206988][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.217092][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.225511][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.231778][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.239389][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.246532][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.253326][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.262125][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.268438][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.278478][ T1] PCI: bus1: Fast back to back transfers enabled [ 9.284728][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.292287][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 9.300273][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.306581][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.370902][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.381065][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.440913][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.451352][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.459766][ T1] printk: console [ttyS0] disabled [ 9.464901][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.474696][ T1] printk: console [ttyS0] enabled [ 9.474696][ T1] printk: console [ttyS0] enabled [ 9.484535][ T1] printk: bootconsole [earlycon0] disabled [ 9.484535][ T1] printk: bootconsole [earlycon0] disabled [ 9.503682][ T1] loop: module loaded [ 9.508149][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.516649][ T1] scsi host0: sata_mv [ 9.521164][ T1] scsi host1: sata_mv [ 9.525325][ T1] ata1: SATA max UDMA/133 irq 33 [ 9.530198][ T1] ata2: SATA max UDMA/133 irq 33 [ 9.536009][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 9.543215][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit [ 9.548555][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.556891][ T1] Scanning device for bad blocks [ 9.766398][ T1] Bad eraseblock 1920 at 0x00000f000000 [ 9.785446][ T1] 3 fixed-partitions partitions found on MTD device orion_nand [ 9.792920][ T1] Creating 3 MTD partitions on "orion_nand": [ 9.798815][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 9.805899][ T1] 0x000000100000-0x000000700000 : "uImage" [ 9.812940][ T1] 0x000000700000-0x000010000000 : "root" [ 9.821897][ T1] libphy: Fixed MDIO Bus: probed [ 9.827564][ T1] libphy: orion_mdio_bus: probed [ 9.832468][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove [ 9.845129][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 9.853225][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 9.870272][ T112] ata1: SATA link down (SStatus 0 SControl F300) [ 10.211768][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 10.580718][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 10.590338][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.597620][ T1] ehci-pci: EHCI PCI platform driver [ 10.602867][ T1] ehci-orion: EHCI orion driver [ 10.607798][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.614062][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.622659][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 10.650103][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.657136][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 10.666167][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.674145][ T1] usb usb1: Product: EHCI Host Controller [ 10.679750][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 10.687110][ T1] usb usb1: SerialNumber: f1050000.ehci [ 10.693156][ T1] hub 1-0:1.0: USB hub found [ 10.697663][ T1] hub 1-0:1.0: 1 port detected [ 10.703076][ T1] usbcore: registered new interface driver usb-storage [ 10.710238][ T1] mousedev: PS/2 mouse device common for all mice [ 10.717107][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 10.722913][ T1] i2c /dev entries driver [ 11.070101][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 11.270793][ T15] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11 [ 11.279727][ T15] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 11.287628][ T15] usb 1-1: Product: USB 2.0 Hub [ 11.292946][ T15] hub 1-1:1.0: USB hub found [ 11.297541][ T15] hub 1-1:1.0: 4 ports detected [ 11.720094][ T15] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 11.971042][ T15] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00 [ 11.980164][ T15] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.988233][ T15] usb 1-1.2: Product: Cruzer Fit [ 11.993071][ T15] usb 1-1.2: Manufacturer: SanDisk' [ 11.998152][ T15] usb 1-1.2: SerialNumber: 00005103080620233952 [ 12.005102][ T15] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 12.012585][ T15] scsi host2: usb-storage 1-1.2:1.0 [ 12.810110][ T1] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0 [ 12.817376][ T1] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-110 addr=0e, data=03 [ 12.825905][ T1] rtc-pcf8563 0-0051: pcf8563_probe: write error [ 12.832185][ T1] rtc-pcf8563: probe of 0-0051 failed with error -5 [ 12.839516][ T1] device-mapper: uevent: version 1.0.3 [ 12.845205][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 12.854848][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.862182][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.869530][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.876986][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.883833][ T1] device-mapper: raid: Loading target version 1.14.0 [ 12.892157][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 12.898615][ T1] drop_monitor: Initializing network drop monitor service [ 12.905977][ T1] NET: Registered protocol family 17 [ 12.911417][ T1] Key type dns_resolver registered [ 12.917187][ T1] registered taskstats version 1 [ 12.922045][ T1] Loading compiled-in X.509 certificates [ 12.927643][ T1] zswap: loaded using pool lzo/zbud [ 12.947960][ T1] Key type big_key registered [ 12.955966][ T1] Key type encrypted registered [ 12.962923][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-12-21T07:39:11 UTC (1608536351) [ 12.972864][ T1] md: Waiting for all devices to be available before autodetect [ 12.980467][ T1] md: If you don't use raid, use raid=noautodetect [ 12.987528][ T1] md: Autodetecting RAID arrays. [ 12.992415][ T1] md: autorun ... [ 12.995925][ T1] md: ... autorun DONE. [ 13.000209][ T1] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 13.008421][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 13.017604][ T1] 1f00 1024 mtdblock0 [ 13.017608][ T1] (driver?) [ 13.025624][ T1] 1f01 6144 mtdblock1 [ 13.025628][ T1] (driver?) [ 13.033642][ T1] 1f02 254976 mtdblock2 [ 13.033646][ T1] (driver?) [ 13.041636][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 13.050640][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.9-kirkwood-tld-1 #1 [ 13.058325][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 13.065348][ T1] [<c010f6ac>] (unwind_backtrace) from [<c010bb00>] (show_stack+0x10/0x14) [ 13.073839][ T1] [<c010bb00>] (show_stack) from [<c0119fa0>] (panic+0xe0/0x30c) [ 13.081458][ T1] [<c0119fa0>] (panic) from [<c0e01628>] (mount_block_root+0x1bc/0x2a4) [ 13.089683][ T1] [<c0e01628>] (mount_block_root) from [<c0e017f8>] (mount_root+0xe8/0x154) [ 13.098256][ T1] [<c0e017f8>] (mount_root) from [<c0e019b0>] (prepare_namespace+0x14c/0x18c) [ 13.107001][ T1] [<c0e019b0>] (prepare_namespace) from [<c0e011c8>] (kernel_init_freeable+0x270/0x2dc) [ 13.116623][ T1] [<c0e011c8>] (kernel_init_freeable) from [<c09dcee0>] (kernel_init+0x8/0x10c) [ 13.125541][ T1] [<c09dcee0>] (kernel_init) from [<c01010e0>] (ret_from_fork+0x14/0x34) [ 13.133842][ T1] Exception stack(0xc7881fb0 to 0xc7881ff8) [ 13.139617][ T1] 1fa0: 00000000 00000000 00000000 00000000 [ 13.148531][ T1] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 13.157441][ T1] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 13.164792][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
root@xubuntu-System-Product-Name:/home/xubuntu/kwboot-tool# ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.pogo_e02.mtd0.kwb -p Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 1 % [......................................................................] ... 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 256 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 4096 60084224 04cb3567-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 723 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4975179 bytes read in 1026 ms (4.6 MiB/s) loading uInitrd ... 9713936 bytes read in 944 ms (9.8 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... 10106 bytes read in 3690 ms (2 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-12-17 11:52:39 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4975115 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f1cc000, end 0fb0f8d0 ... OK Loading Device Tree to 0f1c6000, end 0f1cb779 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000][ T0] Memory: 114320K/131072K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 16752K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008602][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015988][ T0] Console: colour dummy device 80x30 [ 0.021238][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032559][ T0] pid_max: default: 32768 minimum: 301 [ 0.038270][ T0] LSM: Security Framework initializing [ 0.043832][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.051239][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.060005][ T0] *** VALIDATE proc *** [ 0.064299][ T0] *** VALIDATE cgroup1 *** [ 0.068648][ T0] *** VALIDATE cgroup2 *** [ 0.073044][ T0] CPU: Testing write buffer coherency: ok [ 0.080426][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.087633][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.093840][ T1] rcu: Hierarchical SRCU implementation. [ 0.102606][ T1] devtmpfs: initialized [ 0.112170][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.122839][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.129990][ T1] xor: measuring software checksum speed [ 0.228626][ T1] arm4regs : 1083.600 MB/sec [ 0.328626][ T1] 8regs : 650.400 MB/sec [ 0.428624][ T1] 32regs : 945.600 MB/sec [ 0.433531][ T1] xor: using function: arm4regs (1083.600 MB/sec) [ 0.439865][ T1] prandom: seed boundary self test passed [ 0.449697][ T1] prandom: 100 self tests passed [ 0.454519][ T1] pinctrl core: initialized pinctrl subsystem [ 0.461974][ T1] NET: Registered protocol family 16 [ 0.467625][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.476107][ T1] audit: initializing netlink subsys (disabled) [ 0.483526][ T14] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1 [ 0.492162][ T1] cpuidle: using governor ladder [ 0.497056][ T1] cpuidle: using governor menu [ 0.502223][ T1] Feroceon L2: Enabling L2 [ 0.506553][ T1] Feroceon L2: Cache support initialised. [ 0.518180][ T1] No ATAGs? [ 2.568609][ C0] random: fast init done [ 6.483318][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 6.489875][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 6.668931][ T1] raid6: int32x8 gen() 127 MB/s [ 6.839032][ T1] raid6: int32x8 xor() 86 MB/s [ 7.009007][ T1] raid6: int32x4 gen() 129 MB/s [ 7.178878][ T1] raid6: int32x4 xor() 83 MB/s [ 7.348677][ T1] raid6: int32x2 gen() 132 MB/s [ 7.518912][ T1] raid6: int32x2 xor() 94 MB/s [ 7.689167][ T1] raid6: int32x1 gen() 100 MB/s [ 7.858882][ T1] raid6: int32x1 xor() 68 MB/s [ 7.863865][ T1] raid6: using algorithm int32x2 gen() 132 MB/s [ 7.870002][ T1] raid6: .... xor() 94 MB/s, rmw enabled [ 7.875514][ T1] raid6: using intx1 recovery algorithm [ 7.881210][ T1] vgaarb: loaded [ 7.885156][ T1] SCSI subsystem initialized [ 7.890146][ T1] usbcore: registered new interface driver usbfs [ 7.896406][ T1] usbcore: registered new interface driver hub [ 7.902576][ T1] usbcore: registered new device driver usb [ 7.908518][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.914228][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.924139][ T1] PTP clock support registered [ 7.930069][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.974419][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.979148][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.996746][ T1] NET: Registered protocol family 2 [ 9.002704][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 9.011192][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 9.018895][ T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 9.026035][ T1] TCP: Hash tables configured (established 1024 bind 1024) [ 9.033250][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 9.039825][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 9.047079][ T1] NET: Registered protocol family 1 [ 9.052834][ T1] RPC: Registered named UNIX socket transport module. [ 9.059482][ T1] RPC: Registered udp transport module. [ 9.064989][ T1] RPC: Registered tcp transport module. [ 9.070439][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.077607][ T1] PCI: CLS 0 bytes, default 32 [ 9.082624][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.091058][ T1] Initialise system trusted keyrings [ 9.096275][ T1] Key type blacklist registered [ 9.101276][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 9.108522][ T1] zbud: loaded [ 9.112955][ T1] NFS: Registering the id_resolver key type [ 9.118752][ T1] Key type id_resolver registered [ 9.123764][ T1] Key type id_legacy registered [ 9.128506][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.135969][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.143369][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.151398][ T1] fuse: init (API version 7.31) [ 9.156509][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.163897][ T1] orangefs_init: module version upstream loaded [ 9.170016][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 9.181784][ T1] async_tx: api initialized (async) [ 9.186868][ T1] Key type asymmetric registered [ 9.191747][ T1] Asymmetric key parser 'x509' registered [ 9.197396][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.207004][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.217110][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.225527][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.231797][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.239406][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.246549][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.253343][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.262142][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.268455][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.278494][ T1] PCI: bus1: Fast back to back transfers enabled [ 9.284746][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.292305][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 9.300290][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.306596][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.370908][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.381087][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.440911][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.451345][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.459745][ T1] printk: console [ttyS0] disabled [ 9.464877][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.474672][ T1] printk: console [ttyS0] enabled [ 9.474672][ T1] printk: console [ttyS0] enabled [ 9.484518][ T1] printk: bootconsole [earlycon0] disabled [ 9.484518][ T1] printk: bootconsole [earlycon0] disabled [ 9.503660][ T1] loop: module loaded [ 9.508131][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.516626][ T1] scsi host0: sata_mv [ 9.521142][ T1] scsi host1: sata_mv [ 9.525300][ T1] ata1: SATA max UDMA/133 irq 33 [ 9.530180][ T1] ata2: SATA max UDMA/133 irq 33 [ 9.535989][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 9.543197][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit [ 9.548539][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.556874][ T1] Scanning device for bad blocks [ 9.766405][ T1] Bad eraseblock 1920 at 0x00000f000000 [ 9.785455][ T1] 3 fixed-partitions partitions found on MTD device orion_nand [ 9.792930][ T1] Creating 3 MTD partitions on "orion_nand": [ 9.798823][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 9.805902][ T1] 0x000000100000-0x000000700000 : "uImage" [ 9.812940][ T1] 0x000000700000-0x000010000000 : "root" [ 9.821900][ T1] libphy: Fixed MDIO Bus: probed [ 9.827582][ T1] libphy: orion_mdio_bus: probed [ 9.832486][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove [ 9.845211][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 9.853302][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 9.870351][ T112] ata1: SATA link down (SStatus 0 SControl F300) [ 10.211777][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 10.580713][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 10.590329][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.597612][ T1] ehci-pci: EHCI PCI platform driver [ 10.602857][ T1] ehci-orion: EHCI orion driver [ 10.607790][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.614063][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.622658][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 10.650109][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.657134][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 10.666167][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.674146][ T1] usb usb1: Product: EHCI Host Controller [ 10.679749][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 10.687111][ T1] usb usb1: SerialNumber: f1050000.ehci [ 10.693161][ T1] hub 1-0:1.0: USB hub found [ 10.697672][ T1] hub 1-0:1.0: 1 port detected [ 10.703084][ T1] usbcore: registered new interface driver usb-storage [ 10.710247][ T1] mousedev: PS/2 mouse device common for all mice [ 10.717112][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 10.722916][ T1] i2c /dev entries driver [ 11.070107][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 11.270790][ T15] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11 [ 11.279726][ T15] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 11.287627][ T15] usb 1-1: Product: USB 2.0 Hub [ 11.292946][ T15] hub 1-1:1.0: USB hub found [ 11.297539][ T15] hub 1-1:1.0: 4 ports detected [ 11.720101][ T15] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 11.971039][ T15] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00 [ 11.980156][ T15] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.988225][ T15] usb 1-1.2: Product: Cruzer Fit [ 11.993062][ T15] usb 1-1.2: Manufacturer: SanDisk' [ 11.998143][ T15] usb 1-1.2: SerialNumber: 00005103080620233952 [ 12.005099][ T15] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 12.012579][ T15] scsi host2: usb-storage 1-1.2:1.0 [ 12.810116][ T1] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0 [ 12.817383][ T1] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-110 addr=0e, data=03 [ 12.825915][ T1] rtc-pcf8563 0-0051: pcf8563_probe: write error [ 12.832204][ T1] rtc-pcf8563: probe of 0-0051 failed with error -5 [ 12.839550][ T1] device-mapper: uevent: version 1.0.3 [ 12.845230][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 12.854879][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.862210][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.869557][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.877011][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.883858][ T1] device-mapper: raid: Loading target version 1.14.0 [ 12.892189][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 12.898650][ T1] drop_monitor: Initializing network drop monitor service [ 12.906013][ T1] NET: Registered protocol family 17 [ 12.911452][ T1] Key type dns_resolver registered [ 12.917222][ T1] registered taskstats version 1 [ 12.922078][ T1] Loading compiled-in X.509 certificates [ 12.927668][ T1] zswap: loaded using pool lzo/zbud [ 12.947952][ T1] Key type big_key registered [ 12.955983][ T1] Key type encrypted registered [ 12.962942][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-12-21T07:47:38 UTC (1608536858) [ 12.972881][ T1] md: Waiting for all devices to be available before autodetect [ 12.980486][ T1] md: If you don't use raid, use raid=noautodetect [ 12.987556][ T1] md: Autodetecting RAID arrays. [ 12.992449][ T1] md: autorun ... [ 12.995951][ T1] md: ... autorun DONE. [ 13.000237][ T1] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 13.008456][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 13.017640][ T1] 1f00 1024 mtdblock0 [ 13.017644][ T1] (driver?) [ 13.025669][ T1] 1f01 6144 mtdblock1 [ 13.025672][ T1] (driver?) [ 13.033686][ T1] 1f02 254976 mtdblock2 [ 13.033689][ T1] (driver?) [ 13.041672][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 13.050675][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.9-kirkwood-tld-1 #1 [ 13.058360][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 13.065383][ T1] [<c010f6ac>] (unwind_backtrace) from [<c010bb00>] (show_stack+0x10/0x14) [ 13.073873][ T1] [<c010bb00>] (show_stack) from [<c0119fa0>] (panic+0xe0/0x30c) [ 13.081494][ T1] [<c0119fa0>] (panic) from [<c0e01628>] (mount_block_root+0x1bc/0x2a4) [ 13.089718][ T1] [<c0e01628>] (mount_block_root) from [<c0e017f8>] (mount_root+0xe8/0x154) [ 13.098290][ T1] [<c0e017f8>] (mount_root) from [<c0e019b0>] (prepare_namespace+0x14c/0x18c) [ 13.107036][ T1] [<c0e019b0>] (prepare_namespace) from [<c0e011c8>] (kernel_init_freeable+0x270/0x2dc) [ 13.116658][ T1] [<c0e011c8>] (kernel_init_freeable) from [<c09dcee0>] (kernel_init+0x8/0x10c) [ 13.125575][ T1] [<c09dcee0>] (kernel_init) from [<c01010e0>] (ret_from_fork+0x14/0x34) [ 13.133876][ T1] Exception stack(0xc7881fb0 to 0xc7881ff8) [ 13.139651][ T1] 1fa0: 00000000 00000000 00000000 00000000 [ 13.148566][ T1] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 13.157475][ T1] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 13.164827][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
Re: Verbatim MediaShare 47490 December 21, 2020 03:13AM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Verbatim MediaShare 47490 December 21, 2020 03:40AM |
Registered: 3 years ago Posts: 26 |
Re: Verbatim MediaShare 47490 December 21, 2020 04:04AM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Verbatim MediaShare 47490 December 21, 2020 08:44AM |
Registered: 3 years ago Posts: 26 |
Quote
bodhi
There is one more thing to do: set up the /etc/fw_env.config file so that you can read/write u-boot envs while in Debian.
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000
** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 netmask=255.255.255.0 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console=console=ttyS0,115200 rootpath=/tftpboot/marvell.nfs.rootfs image_name=uImage.6281a.ubifs.20090513 serverip=10.128.129.205 ethaddr=00:01:D2:0E:0A:72 arcNumber=2743 bootcmd_usb=usb reset; ext2load usb 0 0x200000 /boot/uImage; ext2load usb 0 0x800000 /boot/uInitrd usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial load_uimage=ext2load usb 0:1 0x800000 /boot/uImage load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000 usb_bootcmd=run usb_set_bootargs; run usb_boot bootcmd=usb start; run usb_bootcmd; usb stop; reset stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=no Environment size: 1593/131068 bytes Marvell>>
login as: root root@192.168.0.85's password: Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Mon Dec 21 02:47:01 2020 root@debian:~# printenv SHELL=/bin/bash PWD=/root LOGNAME=root HOME=/root LANG=C SSH_CONNECTION=192.168.0.252 1213 192.168.0.85 22 TERM=xterm USER=root SHLVL=1 SSH_CLIENT=192.168.0.252 1213 22 PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin MAIL=/var/mail/root SSH_TTY=/dev/pts/0 _=/usr/bin/printenv root@debian:~#
-bash-3.2# printenv HOSTNAME=axentraserver.driver.myverbatim.com TERM=xterm SHELL=/bin/bash HISTSIZE=1000 SSH_CLIENT=172.16.1.254 1212 22 SSH_TTY=/dev/pts/0 USER=root LS_COLORS=no=00:fi=00:di=00;34:ln=00;36:pi=40;33:so=00;35:bd=40;33;01:cd=40;33;01:or=01;05;37;41:mi=01;05;37;41:ex=00;32:*.cmd=00;32:*.exe=00;32:*.com=00;32:*.btm=00;32:*.bat=00;32:*.sh=00;32:*.csh=00;32:*.tar=00;31:*.tgz=00;31:*.arj=00;31:*.taz=00;31:*.lzh=00;31:*.zip=00;31:*.z=00;31:*.Z=00;31:*.gz=00;31:*.bz2=00;31:*.bz=00;31:*.tz=00;31:*.rpm=00;31:*.cpio=00;31:*.jpg=00;35:*.gif=00;35:*.bmp=00;35:*.xbm=00;35:*.xpm=00;35:*.png=00;35:*.tif=00;35: MAIL=/var/spool/mail/root PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin INPUTRC=/etc/inputrc PWD=/root SHLVL=1 HOME=/root LOGNAME=root SSH_CONNECTION=172.16.1.254 1212 192.168.10.250 22 LESSOPEN=|/usr/bin/lesspipe.sh %s G_BROKEN_FILENAMES=1 _=/usr/bin/printenv -bash-3.2#
Re: Verbatim MediaShare 47490 December 21, 2020 04:09PM |
Admin Registered: 13 years ago Posts: 18,564 |
bootcmd=usb start; run usb_bootcmd; usb stop; reset
Re: Verbatim MediaShare 47490 December 21, 2020 05:46PM |
Registered: 3 years ago Posts: 26 |
Will the envs listing in this box work?Quote
I have two Verbatim MediaShare 1TB (47490) № 1 works on original firmware
Re: Verbatim MediaShare 47490 December 21, 2020 10:57PM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
I have two Verbatim MediaShare 1TB (47490)
> № 1 works on original firmware
blparamsAnd post the output here.
Re: Verbatim MediaShare 47490 December 22, 2020 04:50AM |
Registered: 3 years ago Posts: 26 |
root@debian:~# blparamQuote
bodhi
Log into the 2nd Verbatim box, and run blparam
** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console=console=ttyS0,115200 bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 ethaddr=00:01:D2:0E:0C:81 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=no Environment size: 1150/131068 bytes
** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 netmask=255.255.255.0 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console=console=ttyS0,115200 rootpath=/tftpboot/marvell.nfs.rootfs image_name=uImage.6281a.ubifs.20090513 serverip=10.128.129.205 ethaddr=00:01:D2:0E:0A:72 arcNumber=2743 bootcmd_usb=usb reset; ext2load usb 0 0x200000 /boot/uImage; ext2load usb 0 0x800000 /boot/uInitrd usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial load_uimage=ext2load usb 0:1 0x800000 /boot/uImage load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000 usb_bootcmd=run usb_set_bootargs; run usb_boot bootcmd=usb start; run usb_bootcmd; usb stop; reset stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=no Environment size: 1593/131068 bytes Marvell>>
Re: Verbatim MediaShare 47490 December 22, 2020 05:37PM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
Log into the 2nd Verbatim box, and run blparam
root@debian:~# blparam
-bash: blparam: command not found
root@debian:~# find /usr -name '*blparam*'
root@debian:~#
Re: Verbatim MediaShare 47490 December 23, 2020 01:56AM |
Registered: 3 years ago Posts: 26 |
Quote
bodhi
I meant log in to stock OS
root@192.168.10.250's password: -bash-3.2# blparam -bash: blparam: command not found -bash-3.2# find /usr -name '*blparam*' -bash-3.2# -bash-3.2# find -name '*blparam*' -bash-3.2#
the original firmware remainsQuote
Did you install Debian on the 2nd box, too?
Re: Verbatim MediaShare 47490 December 23, 2020 03:05AM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Verbatim MediaShare 47490 December 23, 2020 03:29PM |
Admin Registered: 13 years ago Posts: 18,564 |
> the original firmware remainsQuote
Did you install Debian on the 2nd box,
> too?
printenv
Re: Verbatim MediaShare 47490 December 23, 2020 05:55PM |
Registered: 3 years ago Posts: 26 |
Quote
Do you have serial console on this 2nd box? If you do then it boot up with serial console, interrupt u-boot at count down, and get the envs listing:
printenv
log printenv original firmware ** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console=console=ttyS0,115200 bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 ethaddr=00:01:D2:0E:0C:81 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=no Environment size: 1150/131068 bytes
Re: Verbatim MediaShare 47490 December 23, 2020 09:53PM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv bootcmd_stock 'echo Booting Stock ...; nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000" setenv bootcmd_usb 'echo Booting Debian ...; usb start; run usb_bootcmd; usb stop' setenv bootcmd 'run bootcmd_usb; run bootcmd_stock; reset'
boot
setenv bootcmd_stock 'ehco Booting Stock ...; nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000" setenv bootcmd_usb 'echo Booting Debian ...; usb start; run usb_bootcmd; usb stop' setenv bootcmd 'run bootcmd_usb; run bootcmd_stock; reset' saveenv
Re: Verbatim MediaShare 47490 December 24, 2020 03:43AM |
Registered: 3 years ago Posts: 26 |
Quote
bodhi
setenv bootcmd_stock 'echo Booting Stock ...; nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000"
setenv bootcmd_stock 'echo Booting Stock ...; nand read.e 0x800000 0x100000 0x300000 setenv bootargs $(console) $(bootargs_root); bootm 0x800000"Bad Magic Number
Re: Verbatim MediaShare 47490 December 24, 2020 03:59AM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv bootcmd_stock 'nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000' setenv bootcmd_usb 'echo Booting Debian ...; usb start; run usb_bootcmd; usb stop' setenv bootcmd 'run bootcmd_usb; run bootcmd_stock; reset'
Re: Verbatim MediaShare 47490 December 24, 2020 04:14AM |
Registered: 3 years ago Posts: 26 |
Hit any key to stop autoboot: 0 Marvell>> setenv bootcmd_stock 'nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000' Marvell>> setenv bootcmd_usb 'echo Booting Debian ...; usb start; run usb_bootcmd; usb stop' Marvell>> setenv bootcmd 'run bootcmd_usb; run bootcmd_stock; reset' Marvell>> boot Booting Debian ... (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Bad partition 1 ** ** Bad partition 1 ** ## Booting image at 00800000 ... Bad Magic Number stopping USB.. NAND read: device 0 offset 0x100000, size 0x300000 Reading data from 0x3ff800 -- 100% complete. 3145728 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-12-23 18:37:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2087656 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux.................................................................................................................................... done, booting the kernel.freezes
Re: Verbatim MediaShare 47490 December 24, 2020 03:41PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Verbatim MediaShare 47490 December 25, 2020 09:27AM |
Registered: 3 years ago Posts: 26 |