Hi
I hope someone can help me with restoring my rn102.After load the uboot via kwboot now I can't save uboot to nand .Error: Did not find a cmdline Flattened Device Tree.Could not find a valid device tree.
99 % [.............................................]
[Type Ctrl-\ + c to quit]
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:53:05) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-102 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9ef34
BSS: 0x1ffef0a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf1ad) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000001ea0000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
GBE0
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: , egiga1 [PRIME]
Power On!
Loading FDT from NAND 0xEC000 to 0x1000000 failed!
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
3159060 bytes read
reading /initrd-recovery.gz
2729717 bytes read
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-3.0.101.RN_ARM.4
Created: 2015-04-01 23:06:44 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3158996 Bytes = 3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: initrd-recovery
Created: 2017-12-22 19:19:16 UTC
Image Type: ARM Linux RAMDisk Image (lzma compressed)
Data Size: 2729653 Bytes = 2.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
NANDboot=nand read.e 0x2000000 0x200000 0x400000;nand read.e 0x1000000 0x7e00000 0x20000;nand read.e 0x3000000 0x800000 0x400000;bootz 0x2000000 0x3000000 0x1000000
Product=ReadyNAS 102
SKUNum=RN102
USBboot=fatload usb 0:1 0x2000000 /zImage-recovery;fatload usb 0:1 0x1000000 /RN102-recovery.dtb;fatload usb 0:1 0x3000000 /initrd-recovery.gz;bootz 0x2000000 0x3000000 0x1000000
Version=V1.0
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start;fatload usb 0:1 0x2000000 /uImage-recovery;fatload usb 0:1 0x3000000 /initrd-recovery.gz;nand read 0x1000000 0xD4000 0x6000; bootm 0x2000000 0x3000000 0x1000000
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
check_usb=usb start; fatload usb 0:1 0x2000000 /NTGR_USBBOOT_INFO.txt
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaFPU=no
enaWrAllo=no
envver=3
eth1addr=00:50:43:02:00:00
eth1mtu=1500
ethact=egiga1
ethaddr=00:50:43:02:02:00
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
filesize=29A6F5
image_name=uImage
initrd_high=0xFFFFFFFF
initrd_name=uInitrd
ipaddr=192.168.82.234
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=switch_config=none
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
rootpath=/srv/oneiric
sata_delay_reset=0
sata_dma_mode=yes
serverip=192.168.82.150
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2748/131068 bytes
Marvell>>
Edited 1 time(s). Last edit at 01/24/2021 06:02AM by makczo.