Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian June 05, 2014 01:35PM |
Registered: 12 years ago Posts: 40 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian June 05, 2014 01:39PM |
Registered: 14 years ago Posts: 406 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian June 05, 2014 02:42PM |
Registered: 12 years ago Posts: 40 |
U-Boot 2011.12 (Apr 08 2012 - 19:03:41) Cloud Engines-Pogoplug v4/Mobile:MMC version arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** incorrect device type in data Partition data not found! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. No MMC card found SDHC found. Card desciption is: Manufacturer: 0x03, OEM "SD" Product name: "SU16G", revision 8.0 Serial number: 454569302 Manufacturing date: 7/2012 CRC: 0x00, b0 = 0 mmc1 is available Loading file "/boot/uImage" from mmc device 0:1 (xxa1) 2461416 bytes read Loading file "/boot/uInitrd" from mmc device 0:1 (xxa1) 6362802 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.14.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2461352 Bytes = 2.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.14.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6362738 Bytes = 6.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Using machid 0xf78 from environment Starting kernel ...
U-Boot 2011.12 (Apr 08 2012 - 19:03:41) Cloud Engines-Pogoplug v4/Mobile:MMC version SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 No link on egiga0 ping failed; host 192.168.145.10 is not alive Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** incorrect device type in data Partition data not found! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. No MMC card found SDHC found. Card desciption is: Manufacturer: 0x03, OEM "SD" Product name: "SU16G", revision 8.0 Serial number: 454569302 Manufacturing date: 7/2012 CRC: 0x00, b0 = 0 mmc1 is available Loading file "/boot/uImage" from mmc device 0:1 (xxa1) 2461416 bytes read Loading file "/boot/uInitrd" from mmc device 0:1 (xxa1) 6362802 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.14.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2461352 Bytes = 2.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.14.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6362738 Bytes = 6.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.14.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Apr 1 22:54:58 PDT 2014 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Pogoplug V4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 116244K/131072K available (4779K kernel code, 352K rwdata, 1644K rodata, 213K init, 424K bss, 14828K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc064df14 (6424 kB) [ 0.000000] .init : 0xc064e000 - 0xc0683444 ( 214 kB) [ 0.000000] .data : 0xc0684000 - 0xc06dc3c4 ( 353 kB) [ 0.000000] .bss : 0xc06dc3c4 - 0xc074665c ( 425 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000018] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns [ 4.580150] Console: colour dummy device 80x30 [ 4.580197] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 4.669787] pid_max: default: 32768 minimum: 301 [ 4.669949] Security Framework initialized [ 4.670047] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 4.670079] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 4.670965] Initializing cgroup subsys devices [ 4.671002] Initializing cgroup subsys freezer [ 4.671021] Initializing cgroup subsys net_cls [ 4.671037] Initializing cgroup subsys blkio [ 4.671149] CPU: Testing write buffer coherency: ok [ 4.671728] Setting up static identity map for 0x485fa0 - 0x485fdc [ 4.674922] devtmpfs: initialized [ 4.678929] prandom: seed boundary self test passed [ 4.684990] prandom: 100 self tests passed [ 4.685012] pinctrl core: initialized pinctrl subsystem [ 4.685588] regulator-dummy: no parameters [ 4.686096] NET: Registered protocol family 16 [ 4.686766] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 4.687950] cpuidle: using governor ladder [ 4.687976] cpuidle: using governor menu [ 4.688149] Kirkwood: MV88F6281-A1, TCLK=166666667. [ 4.688181] Feroceon L2: Enabling L2 [ 4.688233] Feroceon L2: Cache support initialised. [ 4.688927] POGOPLUGV4: failed to setup USB VBUS GPIO [ 4.690114] Kirkwood PCIe port 0: link down [ 4.690129] PCI: bus0 uses PCIe port 0 [ 4.690304] PCI host bridge to bus 0000:00 [ 4.690334] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 4.690352] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 4.690371] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 4.690801] PCI: bus0: Fast back to back transfers disabled [ 4.697079] bio: create slab <bio-0> at 0 [ 4.697733] vgaarb: loaded [ 4.698156] usbcore: registered new interface driver usbfs [ 4.698253] usbcore: registered new interface driver hub [ 4.698416] usbcore: registered new device driver usb [ 4.699492] Switched to clocksource orion_clocksource [ 4.734954] NET: Registered protocol family 2 [ 4.735880] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 4.735917] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 4.735947] TCP: Hash tables configured (established 1024 bind 1024) [ 4.736054] TCP: reno registered [ 4.736073] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 4.736105] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 4.736388] NET: Registered protocol family 1 [ 4.736843] RPC: Registered named UNIX socket transport module. [ 4.736858] RPC: Registered udp transport module. [ 4.736868] RPC: Registered tcp transport module. [ 4.736878] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.737252] Unpacking initramfs... [ 5.513413] Freeing initrd memory: 6208K (c1101000 - c1711000) [ 5.513578] NetWinder Floating Point Emulator V0.97 (double precision) [ 5.514377] futex hash table entries: 256 (order: -1, 3072 bytes) [ 5.514601] audit: initializing netlink subsys (disabled) [ 5.514677] audit: type=2000 audit(0.920:1): initialized [ 5.515630] bounce pool size: 64 pages [ 5.515729] zbud: loaded [ 5.515983] VFS: Disk quotas dquot_6.5.2 [ 5.516061] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.516482] NFS: Registering the id_resolver key type [ 5.516589] Key type id_resolver registered [ 5.516603] Key type id_legacy registered [ 5.516628] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 5.516642] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 5.516871] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 5.517267] msgmni has been set to 239 [ 5.517439] Key type big_key registered [ 5.520181] alg: No test for stdrng (krng) [ 5.520311] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 5.520327] io scheduler noop registered [ 5.520339] io scheduler deadline registered [ 5.520386] io scheduler cfq registered (default) [ 5.520787] mv_xor mv_xor.0: Marvell shared XOR driver [ 5.559581] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 5.599573] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 5.599747] mv_xor mv_xor.1: Marvell shared XOR driver [ 5.639581] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 5.679579] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 5.680011] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.700892] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A [ 6.287649] console [ttyS0] enabled [ 6.292668] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 6.298997] nand: Hynix H27U1G8F2BTR-BC [ 6.302855] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 6.308501] Scanning device for bad blocks [ 6.321501] Bad eraseblock 80 at 0x000000a00000 [ 6.430192] 5 cmdlinepart partitions found on MTD device orion_nand [ 6.436434] Creating 5 MTD partitions on "orion_nand": [ 6.441578] 0x000000000000-0x000000200000 : "u-boot" [ 6.446916] 0x000000200000-0x000000500000 : "uImage" [ 6.452270] 0x000000500000-0x000000800000 : "uImage2" [ 6.457671] 0x000000800000-0x000001000000 : "failsafe" [ 6.463190] 0x000001000000-0x000008000000 : "root" [ 6.468927] m25p80 spi0.0: m25p05-nonjedec (64 Kbytes) [ 6.483740] libphy: Fixed MDIO Bus: probed [ 6.502286] libphy: orion_mdio_bus: probed [ 6.506509] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.587865] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:03:eb:23 [ 7.596841] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.603370] ehci-pci: EHCI PCI platform driver [ 7.607882] ehci-orion: EHCI orion driver [ 7.612003] orion-ehci orion-ehci.0: EHCI Host Controller [ 7.617416] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 7.625336] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 7.649538] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 7.655661] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.662457] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.669671] usb usb1: Product: EHCI Host Controller [ 7.674532] usb usb1: Manufacturer: Linux 3.14.0-kirkwood-tld-1 ehci_hcd [ 7.681229] usb usb1: SerialNumber: orion-ehci.0 [ 7.686676] hub 1-0:1.0: USB hub found [ 7.690499] hub 1-0:1.0: 1 port detected [ 7.695191] mousedev: PS/2 mouse device common for all mice [ 8.709696] rtc-mv rtc-mv: internal RTC not ticking [ 8.714718] i2c /dev entries driver [ 8.719094] hidraw: raw HID events driver (C) Jiri Kosina [ 8.724926] drop_monitor: Initializing network drop monitor service [ 8.731479] TCP: cubic registered [ 8.734790] NET: Registered protocol family 17 [ 8.739361] Key type dns_resolver registered [ 8.744331] registered taskstats version 1 [ 8.749161] regulator-dummy: incomplete constraints, leaving on [ 8.755549] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 8.764224] Freeing unused kernel memory: 212K (c064e000 - c0683000) Loading, please wait... [ 8.859454] udevd[57]: starting version 175 [ 9.103416] mvsdio mvsdio: no pins associated [ 9.128549] SCSI subsystem initialized [ 9.179730] mvsdio mvsdio: using GPIO for card detection [ 9.238170] sata_mv sata_mv.0: cannot get optional clkdev [ 9.252801] mmc0: host does not support reading read-only switch. assuming write-enable. [ 9.272016] mmc0: new high speed SDHC card at address e624 [ 9.283230] sata_mv sata_mv.0: slots 32 ports 1 [ 9.315010] scsi0 : sata_mv [ 9.318188] ata1: SATA max UDMA/133 irq 21 [ 9.399916] mmcblk0: mmc0:e624 SU16G 14.8 GiB [ 9.408371] mmcblk0: p1 [ 9.689557] ata1: SATA link down (SStatus 0 SControl F300) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Waiting for root file system ... done. Gave up waiting for root device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) ALERT! /dev/sda1 does not exist. Dropping to a shell! modprobe: module i8042 not found in modules.dep [ 30.131175] uhci_hcd: USB Universal Host Controller Interface driver [ 30.150832] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 30.171834] usbcore: registered new interface driver usbhid [ 30.177392] usbhid: USB HID core driver BusyBox v1.20.2 (Debian 1:1.20.0-7) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs)
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian June 05, 2014 06:25PM |
Registered: 10 years ago Posts: 34 |
ALERT! /dev/sda1 does not exist. Dropping to a shell!
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian June 05, 2014 11:36PM |
Admin Registered: 13 years ago Posts: 18,821 |
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian June 06, 2014 02:15PM |
Registered: 12 years ago Posts: 40 |
LouisV
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 03:11PM |
cd /tmp wget http://download.doozan.com/uboot/nanddump wget http://download.doozan.com/uboot/nandwrite wget http://download.doozan.com/uboot/flash_erase wget http://download.doozan.com/uboot/fw_printenv wget http://download.doozan.com/uboot/fw_env.config wget http://download.doozan.com/uboot/files/environment/uboot.environment
chmod +x *
cp fw_env.config /etc/fw_env.config cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000
#df ubi0:rootfs 99432 14572 84860 15% / none 59312 1388 57924 2% /tmp /tmp/.cemnt/mmcblk0p1 15318484 454136 14086212 3% /tmp/.cemnt/mnt_mmcblk0p1
./flash_erase /dev/mtd0 0 4 Erase Total 4 Units Performing Flash Erase of length 131072 at offset 0x60000 done
./nandwrite /dev/mtd0 uboot.nandpogoV4-MMC-mtdparts-noSATA.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000
./flash_erase /dev/mtd0 0xc0000 1 Erase Total 1 Units Performing Flash Erase of length 131072 at offset 0xc0000 done
./nandwrite -s 786432 /dev/mtd0 uboot.environment Writing data to block 6 at offset 0xc0000
/tmp # ./fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 arcNumber=2097 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
./fw_setenv mtdparts 'mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)' -sh: ./fw_setenv: not found
# ln -s fw_printenv fw_setenv # ./fw_setenv mtdparts 'mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)'
./fw_printenv mtdparts mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)It seems to have worked.
./fw_setenv serverip 192.168.1.100 ./fw_setenv ipaddr 192.168.1.56 ./fw_setenv if_netconsole 'ping $serverip' ./fw_setenv start_netconsole 'setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;' ./fw_setenv preboot 'run if_netconsole start_netconsole'Everything sets fine. I won't echo fw_printenv for the sake of brevity.
./fw_setenv bootcmd 'usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run mmc_bootcmd' ./fw_setenv mmc_bootcmd 'mmc init; mmc init;ext2load mmc 0:1 0x00800000 /boot/uImage; if ext2load mmc 0:1 0x01100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
# /sbin/poweroff Connection to pogoplugmobile closed by remote host. Connection to pogoplugmobile closed.
fw_setenv mmc_root /dev/mmcblk0p1 fw_setenv mmc_set_bootargs 'setenv bootargs console=$console root=$mmc_root' fw_setenv mmc_boot 'mw 0x800000 0 1; ext2load mmc 0:1 0x00800000 /boot/uImage; if ext2load mmc 0:1 0x01100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi' fw_setenv mmc_bootcmd 'mmc init; mmc init; run mmc_set_bootargs; run mmc_boot'
U-Boot 2011.12 (Apr 08 2012 - 19:03:41) Cloud Engines-Pogoplug v4/Mobile:MMC version arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** incorrect device type in data Partition data not found! Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 (usbda1) 2461416 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 6362802 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.14.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2461352 Bytes = 2.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.14.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6362738 Bytes = 6.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
U-Boot 2011.12 (Apr 08 2012 - 19:03:41) Cloud Engines-Pogoplug v4/Mobile:MMC version arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** incorrect device type in data Partition data not found! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. SDHC found. Card desciption is: Manufacturer: 0x74, OEM "JE" Product name: "SDC ", revision 0.2 Serial number: 60825326 Manufacturing date: 8/2013 CRC: 0x00, b0 = 0 mmc1 is available SDHC found. Card desciption is: Manufacturer: 0x74, OEM "JE" Product name: "SDC ", revision 0.2 Serial number: 60825326 Manufacturing date: 8/2013 CRC: 0x00, b0 = 0 mmc1 is available Loading file "/boot/uImage" from mmc device 0:1 (xxa1) ** File not found /boot/uImage Loading file "/boot/uInitrd" from mmc device 0:1 (xxa1) ** File not found /boot/uInitrd Wrong Image Format for bootm command ERROR: can't get kernel image!
fw_setenv usb_init 'run usb_scan; setenv usb_root LABEL=rootfs'
fw_setenv mmc_set_bootargs 'setenv bootargs console=$console root=$mmc_root rootfstype=$mmc_rootfstype $mtdparts'
fw_setenv mmc_rootfstype 'ext3'
root@debian:~# fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 arcNumber=2097 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_device=0:1 usb_root=/dev/sda1 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) ipaddr=192.168.1.56 if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run mmc_bootcmd mmc_root=/dev/mmcblk0p1 mmc_boot=mw 0x800000 0 1; ext2load mmc 0:1 0x00800000 /boot/uImage; if ext2load mmc 0:1 0x01100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_bootcmd=mmc init; mmc init; run mmc_set_bootargs; run mmc_boot serverip=192.168.1.100 usb_rootfstype=ext3 usb_init=run usb_scan; setenv usb_root LABEL=rootfs mmc_set_bootargs=setenv bootargs console=$console root=$mmc_root rootfstype=$mmc_rootfstype $mtdparts mmc_rootfstype=ext3
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 03:37PM |
Registered: 11 years ago Posts: 165 |
Loading file "/boot/uImage" from mmc device 0:1 (xxa1) ** File not found /boot/uImage
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 04:09PM |
Admin Registered: 13 years ago Posts: 18,821 |
mmc init ext2ls mmc 0:1 /boot
LouisV
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 04:12PM |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 04:18PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 05:36PM |
Registered: 11 years ago Posts: 165 |
LouisV
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 06:11PM |
root@debian:~# fdisk -l Disk /dev/mmcblk0: 15.9 GB, 15937306624 bytes 255 heads, 63 sectors/track, 1937 cylinders, total 31127552 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0005ff89 Device Boot Start End Blocks Id System /dev/mmcblk0p1 2048 31127551 15562752 83 Linux Disk /dev/sda: 8022 MB, 8022654976 bytes 94 heads, 14 sectors/track, 11906 cylinders, total 15669248 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b0317 Device Boot Start End Blocks Id System /dev/sda1 2048 15669247 7833600 83 Linux
root@debian:~# df Filesystem 1K-blocks Used Available Use% Mounted on rootfs 7579576 299488 6888408 5% / udev 10240 0 10240 0% /dev tmpfs 12268 84 12184 1% /run /dev/disk/by-label/rootfs 7579576 299488 6888408 5% / tmpfs 5120 0 5120 0% /run/lock tmpfs 24520 0 24520 0% /run/shm tmpfs 61332 0 61332 0% /tmp /dev/mmcblk0p1 15203328 319716 14111312 3% /root/sd
root@debian:~# ls -ll /boot total 19112 drwxr-xr-x 2 root root 4096 Apr 6 13:47 . drwxr-xr-x 22 root root 4096 Apr 6 14:10 .. -rw-r--r-- 1 root root 1736932 Apr 2 01:25 System.map-3.14.0-kirkwood-tld-1 -rw-r--r-- 1 root root 123040 Apr 1 22:19 config-3.14.0-kirkwood-tld-1 -rw-r--r-- 1 root root 6362738 Apr 6 13:39 initrd.img-3.14.0-kirkwood-tld-1 -rw-r--r-- 1 root root 2461416 Apr 6 13:44 uImage -rw-r--r-- 1 root root 6362802 Apr 6 13:44 uInitrd -rw-r--r-- 1 root root 2461352 Apr 2 01:25 vmlinuz-3.14.0-kirkwood-tld-1 root@debian:~# ls -ll sd/boot total 19112 drwxr-xr-x 2 root root 4096 Apr 6 13:47 . drwxr-xr-x 22 root root 4096 Apr 6 14:10 .. -rw-r--r-- 1 root root 1736932 Apr 2 01:25 System.map-3.14.0-kirkwood-tld-1 -rw-r--r-- 1 root root 123040 Apr 1 22:19 config-3.14.0-kirkwood-tld-1 -rw-r--r-- 1 root root 6362738 Apr 6 13:39 initrd.img-3.14.0-kirkwood-tld-1 -rw-r--r-- 1 root root 2461416 Apr 6 13:44 uImage -rw-r--r-- 1 root root 6362802 Apr 6 13:44 uInitrd -rw-r--r-- 1 root root 2461352 Apr 2 01:25 vmlinuz-3.14.0-kirkwood-tld-1
root@debian:~# e2label /dev/sda1 rootfs root@debian:~# e2label /dev/mmcblk0p1 rootfs
root@debian:~# lsblk -f NAME FSTYPE LABEL MOUNTPOINT sda `-sda1 ext3 rootfs / mmcblk0 `-mmcblk0p1 ext3 rootfs
LouisV
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 06:56PM |
root@debian:~# mke2fs -L rootfs -j /dev/mmcblk0p1 mke2fs 1.42.5 (29-Jul-2012) Filesystem label=rootfs OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 972944 inodes, 3890688 blocks 194534 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=3984588800 119 block groups 32768 blocks per group, 32768 fragments per group 8176 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208 Allocating group tables: done Writing inode tables: done Creating journal (32768 blocks): done Writing superblocks and filesystem accounting information: done
root@debian:~# mount /dev/mmcblk0p1 sd
root@debian:~# wget --no-check-certificate https://www.dropbox.com/s/16r9mv9nfh9so3j/Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 [...] HTTP request sent, awaiting response... 200 OK Length: 99339058 (95M) [application/octet-stream] Saving to: `Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2' 100%[===========================================================================================>] 99,339,058 324K/s in 5m 8s 2014-07-21 16:21:01 (314 KB/s) - `Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2' saved [99339058/99339058]
root@debian:~# md5sum Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 3c55093a67ea6166b31c9d111d896727 ../Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2
root@debian:~# cd sd root@debian:~/sd# ls . .. lost+found root@debian:~/sd# tar -xjf ../Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 root@debian:~/sd# sync
Loading file "/boot/uImage" from mmc device 0:1 (xxa1) ** ext2fs_devread read outside partition sector 1639251488 ** File not found /boot/uImage Loading file "/boot/uInitrd" from mmc device 0:1 (xxa1) ** ext2fs_devread read outside partition sector 1639251488 ** File not found /boot/uInitrd Wrong Image Format for bootm command ERROR: can't get kernel image!
Hit any key to stop autoboot: 8 0 Pogov4> mmc init mmc init SDHC found. Card desciption is: Manufacturer: 0x6f, OEM "\xff\xff" Product name: "SD ", revision 0.0 Serial number: 268436523 Manufacturing date: 6/2011 CRC: 0x00, b0 = 0 mmc1 is available Pogov4> ext2ls mmc 0:1 /boot ext2ls mmc 0:1 /boot mmc block read error mmc block read error mmc block read error mmc block read error mmc block read error mmc block read error ** ext2fs_devread read outside partition sector 1639251488 Pogov4>
Pogov4> ext2ls mmc 0:1 /boot ext2ls mmc 0:1 /boot
Pogov4> ext2ls mmc 0:1 / ext2ls mmc 0:1 / <DIR> 4096 . <DIR> 4096 .. <DIR> 16384 lost+found <DIR> 98306 proc <DIR> 4096 sbin <DIR> 0 dev <DIR> 98306 root <SYM> 34 vmlinuz <DIR> 0 usr <DIR> 0 selinux <DIR> 0 opt <DIR> 0 boot <DIR> 0 bin <DIR> 0 etc <DIR> 0 tmp <SYM> 37 initrd.img <DIR> 0 mnt <DIR> 4096 var <DIR> 0 home <DIR> 4096 media <DIR> 0 sys <DIR> 4096 run <DIR> 0 lib <DIR> 0 srv
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 07:32PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
> Pogov4> ext2ls mmc 0:1 /boot
> ext2ls mmc 0:1 /boot
> [/code]
>
> I'm not sure, but shouldn't I see the boot files
> listed?
>
> Pogov4> ext2ls mmc 0:1 /
> ext2ls mmc 0:1 /
> <DIR> 4096 .
> <DIR> 4096 ..
> <DIR> 16384 lost+found
> <DIR> 98306 proc
> <DIR> 4096 sbin
> <DIR> 0 dev
> <DIR> 98306 root
> <SYM> 34 vmlinuz
> <DIR> 0 usr
> <DIR> 0 selinux
> <DIR> 0 opt
> <DIR> 0 boot
> <DIR> 0 bin
> <DIR> 0 etc
> <DIR> 0 tmp
> <SYM> 37 initrd.img
> <DIR> 0 mnt
> <DIR> 4096 var
> <DIR> 0 home
> <DIR> 4096 media
> <DIR> 0 sys
> <DIR> 4096 run
> <DIR> 0 lib
> <DIR> 0 srv
LouisV
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 10:26PM |
root@debian:~/uboot# cat /proc/mtd dev: size erasesize name mtd0: 00200000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00300000 00020000 "uImage2" mtd3: 00800000 00020000 "failsafe" mtd4: 07000000 00020000 "root"
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)back to
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
root@debian:~# fw_printenv arcNumber=2097 machid=0x831 baudrate=115200 bootcmd=run bootcmd_usb; bootcmd_mmc; bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 ethaddr=00:25:31:05:C6:7D ipaddr=192.168.1.56 serverip=192.168.1.100 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
preboot_nc=run if_netconsole start_netconsoleto
preboot=run if_netconsole start_netconsolethe netconsole works again.
Unknown command 'bootcmd_mmc' - try 'help' Unknown command 'bootcmd_sata' - try 'help' resetting ...
LouisV
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 10:34PM |
bootcmd=run bootcmd_usb; bootcmd_mmc; bootcmd_sata; resetto
bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 gcc (Debian 4.6.3-14) 4.6.3 GNU ld (GNU Binutils for Debian) 2.22 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! MMC rescan: current device # 0 initialized OK 2461416 bytes read in 1372 ms (1.7 MiB/s) 6362802 bytes read in 1667 ms (3.6 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.14.0-kirkwood-tld-1 Created: 2014-04-06 20:44:27 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2461352 Bytes = 2.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.14.0-kirkwood-tld-1 Created: 2014-04-06 20:44:41 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6362738 Bytes = 6.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 10:37PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 10:41PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian July 21, 2014 11:00PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
> As per my potentially flawed interpretation of
> your directions I changed
>> mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage) > ,32M(rootfs),-(data) >> back to
>> mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage) > ,3M(uImage2),8M(failsafe),112M(root) >
Quote
> However, after I changed:
>> preboot_nc=run if_netconsole start_netconsole >> to
>> preboot=run if_netconsole start_netconsole >> the netconsole works again.
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 03, 2014 09:27AM |
Registered: 10 years ago Posts: 5 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 04, 2014 09:39AM |
Registered: 10 years ago Posts: 8 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 04, 2014 03:24PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 04, 2014 04:30PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
> I followed below steps to install debian on my
> pogo V4-A1.
> http://blog.qnology.com/2014/07/hacking-pogoplug-v
> 4-series-4-and-mobile.html
> Blogger claims that instock
> firmware is present in NAND but needs change in
> uBoot to access it. It further suggests that i can
> reboot the pogo with 'revert' as a empty folder in
> a new USB .. but that does not work for me. It
> keeps on rebooting.
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 04, 2014 06:07PM |
Registered: 10 years ago Posts: 5 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 04, 2014 08:19PM |
Registered: 11 years ago Posts: 165 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 05, 2014 06:27AM |
Registered: 10 years ago Posts: 8 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 05, 2014 07:35AM |
Registered: 10 years ago Posts: 5 |
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 05, 2014 02:55PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
do i first install the uboot files or do i have to prepare a usb/sdcard with debian first,, i tried to use jeffs script for this but it seems to be broken.
i am still on a stock atm.
Re: [Pogoplug Mobile/Series 4] Install uBoot/Debian August 05, 2014 03:07PM |
Registered: 10 years ago Posts: 8 |