|
basti523
Pogoplug v2 hang at booting debian squeeze at "NET: Registered protocol family 10" May 04, 2013 11:00AM |
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
NAND read: device 0 offset 0x100000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.3.2-kirkwide
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3627768 Bytes = 3.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
For me, this looks all right!?
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.0-4-kirkwood (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-12) ) #1 Debian 3.2.35-2 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Marvell SheevaPlug Reference Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] free_area_init_node: node 0, pgdat c043fa44, node_mem_map c04a6000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65024 pages, LIFO batch:15 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 248496k/248496k available, 13648k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc03e3130 (3949 kB) [ 0.000000] .init : 0xc03e4000 - 0xc0408000 ( 144 kB) [ 0.000000] .data : 0xc0408000 - 0xc0442520 ( 234 kB) [ 0.000000] .bss : 0xc0442544 - 0xc04a5b84 ( 398 kB) [ 0.000000] NR_IRQS:114 [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms [ 0.000000] Console: colour dummy device 80x30 [ 13.531415] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 13.621302] pid_max: default: 32768 minimum: 301 [ 13.621426] Security Framework initialized [ 13.621502] Mount-cache hash table entries: 512 [ 13.621839] Initializing cgroup subsys cpuacct [ 13.621865] Initializing cgroup subsys memory [ 13.621889] Initializing cgroup subsys devices [ 13.621899] Initializing cgroup subsys freezer [ 13.621907] Initializing cgroup subsys net_cls [ 13.621915] Initializing cgroup subsys blkio [ 13.621936] Initializing cgroup subsys perf_event [ 13.622026] CPU: Testing write buffer coherency: ok [ 13.623310] devtmpfs: initialized [ 13.625155] print_constraints: dummy: [ 13.625403] NET: Registered protocol family 16 [ 13.626202] Kirkwood: MV88F6281-A0, TCLK=200000000. [ 13.626215] Feroceon L2: Enabling L2 [ 13.626251] Feroceon L2: Cache support initialised. [ 13.626842] initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00000000 00000000 [ 13.626864] final MPP regs: 01111111 11113322 00001111 00000000 00000000 00000000 00000000 [ 13.629103] bio: create slab <bio-0> at 0 [ 13.629477] vgaarb: loaded [ 13.630018] Switching to clocksource orion_clocksource [ 13.644164] NET: Registered protocol family 2 [ 13.644370] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 13.644981] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 13.645165] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 13.645260] TCP: Hash tables configured (established 8192 bind 8192) [ 13.645269] TCP reno registered [ 13.645279] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 13.645306] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 13.645516] NET: Registered protocol family 1 [ 13.645546] PCI: CLS 0 bytes, default 32 [ 13.645699] Unpacking initramfs... [ 14.193184] Freeing initrd memory: 6600K [ 14.193199] NetWinder Floating Point Emulator V0.97 (double precision) [ 14.193745] audit: initializing netlink socket (disabled) [ 14.193787] type=2000 audit(0.650:1): initialized [ 14.195187] VFS: Disk quotas dquot_6.5.2 [ 14.195272] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 14.195393] JFFS2 version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 14.195730] msgmni has been set to 498 [ 14.197254] alg: No test for stdrng (krng) [ 14.197366] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 14.197379] io scheduler noop registered [ 14.197386] io scheduler deadline registered [ 14.197440] io scheduler cfq registered (default) [ 14.197518] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver [ 14.197552] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver [ 14.230087] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 14.270086] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) [ 14.310085] mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) [ 14.350084] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) [ 14.350468] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 14.371009] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 14.798163] console [ttyS0] enabled [ 14.802638] ONFI flash detected [ 14.806039] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 14.814545] Scanning device for bad blocks [ 14.894217] 4 cmdlinepart partitions found on MTD device orion_nand [ 14.900522] Creating 4 MTD partitions on "orion_nand": [ 14.905687] 0x000000000000-0x000000100000 : "u-boot" [ 14.911505] 0x000000100000-0x000000500000 : "uImage" [ 14.917279] 0x000000500000-0x000002500000 : "rootfs" [ 14.923123] 0x000002500000-0x000008000000 : "data" [ 14.929464] mousedev: PS/2 mouse device common for all mice [ 15.940072] rtc-mv rtc-mv: internal RTC not ticking [ 15.945072] i2c /dev entries driver [ 15.948724] cpuidle: using governor ladder [ 15.952983] cpuidle: using governor menu [ 15.957063] Registered led device: plug:red:misc [ 15.957167] Registered led device: plug:green:health [ 15.957910] TCP cubic registered [ 15.961172] NET: Registered protocol family 17 [ 15.965646] Registering the dns_resolver key type [ 15.970415] Gating clock of unused units [ 15.970424] before: 0x00dfc3fd [ 15.970431] after: 0x00c701d9 [ 15.970858] registered taskstats version 1 [ 15.975413] /build/buildd-linux_3.2.35-2-armel-th89m3/linux-3.2.35/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 15.986576] Initializing network drop monitor service [ 15.992259] Freeing init memory: 144K [ 16.050604] udevd[48]: starting version 175 [ 16.137957] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 16.202736] mv643xx_eth smi: probed [ 16.246343] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:25:31:04:8e:ad [ 16.265834] usbcore: registered new interface driver usbfs [ 16.287709] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling) [ 16.302581] usbcore: registered new interface driver hub [ 16.327744] usbcore: registered new device driver usb [ 16.356688] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 16.392845] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 16.398156] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 16.450075] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 16.470053] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 16.476068] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.482905] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.490170] usb usb1: Product: Marvell Orion EHCI [ 16.494893] usb usb1: Manufacturer: Linux 3.2.0-4-kirkwood ehci_hcd [ 16.501200] usb usb1: SerialNumber: orion-ehci.0 [ 16.506743] hub 1-0:1.0: USB hub found [ 16.510549] hub 1-0:1.0: 1 port detected [ 16.830068] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 16.981457] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 16.988185] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 16.995366] usb 1-1: Product: USB2.0 Hub [ 17.003533] hub 1-1:1.0: USB hub found [ 17.013495] hub 1-1:1.0: 4 ports detected [ 17.290353] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 17.400956] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5151 [ 17.407862] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.415216] usb 1-1.1: Product: Cruzer Micro [ 17.419501] usb 1-1.1: Manufacturer: SanDisk [ 17.423823] usb 1-1.1: SerialNumber: 0000A9709012037D [ 17.454315] SCSI subsystem initialized [ 17.462979] Initializing USB Mass Storage driver... [ 17.468184] scsi0 : usb-storage 1-1.1:1.0 [ 17.473764] usbcore: registered new interface driver usb-storage [ 17.479798] USB Mass Storage support registered. [ 18.471050] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Micro 6.51 PQ: 0 ANSI: 0 CCS [ 18.495386] sd 0:0:0:0: [sda] 3910655 512-byte logical blocks: (2.00 GB/1.86 GiB) [ 18.503353] sd 0:0:0:0: [sda] Write Protect is off [ 18.508171] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08 [ 18.508602] sd 0:0:0:0: [sda] No Caching mode page present [ 18.514130] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 18.523602] sd 0:0:0:0: [sda] No Caching mode page present [ 18.529113] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 18.538609] sda: sda1 sda2 [ 18.544728] sd 0:0:0:0: [sda] No Caching mode page present [ 18.550261] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 18.556381] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.571517] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 26.577937] kjournald starting. Commit interval 5 seconds [ 26.583607] EXT3-fs (sda1): mounted filesystem with ordered data mode [ 27.787125] udevd[242]: starting version 175 [ 29.089212] Adding 251776k swap on /dev/sda2. Priority:-1 extents:1 across:251776k [ 29.427904] EXT3-fs (sda1): using internal journal [ 36.067922] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 54.387527] NET: Registered protocol family 10
# /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> /dev/root / ext2 noatime,errors=remount-ro 0 1 /dev/sda2 none swap sw 0 0
Linux rescue 3.3.2-kirkwide #1 Mon Oct 29 17:52:07 CDT 2012 armv5tel GNU/Linux
|
Termo
Re: Pogoplug v2 hang at booting debian squeeze at "NET: Registered protocol family 10" May 28, 2013 04:22AM |
|
Termo
Re: Pogoplug v2 hang at booting debian squeeze at "NET: Registered protocol family 10" May 30, 2013 03:34PM |