Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives
Posted by daviddyer
|
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 08, 2022 10:43PM |
Registered: 7 years ago Posts: 366 |
On lm-sensors
To be safe, I rebooted the system.
Will install fancontrol and test that tomorrow.
root@debian:~# sensors-detect
# sensors-detect revision $Revision$
# DMI data unavailable, please consider installing dmidecode 2.7
# or later for better results.
# Kernel: 5.9.12-kirkwood-tld-1 armv5tel
# Processor: Feroceon 88FR131 rev 1 (v5l) (//)
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): yes
modprobe: FATAL: Module cpuid not found in directory /lib/modules/5.9.12-kirkwood-tld-1
Failed to load module cpuid.
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
AMD Family 12h and 14h thermal sensors... No
AMD Family 15h thermal sensors... No
AMD Family 16h thermal sensors... No
AMD Family 17h thermal sensors... No
AMD Family 15h power sensors... No
AMD Family 16h power sensors... No
Intel digital thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
Intel 5500/5520/X58 thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): yes
Sorry, no supported PCI bus adapters found.
Next adapter: mv64xxx_i2c adapter (i2c-0)
Do you want to scan it? (YES/no/selectively): YES
Client found at address 0x4c
Handled by driver `lm63' (already loaded), chip type `lm63'
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `lm63':
* Bus `mv64xxx_i2c adapter'
Busdriver `UNKNOWN', I2C address 0x4c
Chip `lm63' (confidence: 6)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
lm63
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
Successful!
Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/kmod start'
to load them.
To be safe, I rebooted the system.
root@debian:~# sensors
lm63-i2c-0-4c
Adapter: mv64xxx_i2c adapter
temp1: +45.0 C (high = +70.0 C)
temp2: +43.4 C (low = +0.0 C, high = +70.0 C)
(crit = +85.0 C, hyst = +75.0 C)
Will install fancontrol and test that tomorrow.
|
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 11:05AM |
Registered: 7 years ago Posts: 366 |
https://e2e.ti.com/support/sensors-group/sensors/f/sensors-forum/935680/lm63-pwm-setting-question
Looks like I can control the fan speed (I can tell it by noise).
Install i2c-tools
i2cset -f -y 0 0x4c 0x4D 0x07
i2cset -f -y 0 0x4c 0x4c 0x0B ==> PWM is %75
i2cset -f -y 0 0x4c 0x4D 0x07
i2cset -f -y 0 0x4c 0x4c 0x07 ==> PWM is %50
Therefore,
i2cset -f -y 0 0x4c 0x4D 0x07
i2cset -f -y 0 0x4c 0x4c 0x09==> PWM is %64
Looks like I can control the fan speed (I can tell it by noise).
Install i2c-tools
i2cset -f -y 0 0x4c 0x4D 0x07
i2cset -f -y 0 0x4c 0x4c 0x0B ==> PWM is %75
i2cset -f -y 0 0x4c 0x4D 0x07
i2cset -f -y 0 0x4c 0x4c 0x07 ==> PWM is %50
Therefore,
i2cset -f -y 0 0x4c 0x4D 0x07
i2cset -f -y 0 0x4c 0x4c 0x09==> PWM is %64
|
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 04:03PM |
Admin Registered: 13 years ago Posts: 18,549 |
Cool!
=======
There is 2 low priority items that have not been tested:
1. Using large HDDs (> 2TB) with this u-boot. It should work with both SATA and USB HDD enclosure/adapter.
Note: when using USB HDD, the disk should be formatted with the interface as intended usage (with the enclosure/adapter). IOW, a large disk formatted in the SATA slot sometime has problem in USB enclosure/adapter.
2. Netconsole. This might be problematic, so don't spend too much time on it. I saw some problem in testing other 2021.10 u-boots, and need to investigate.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
=======
There is 2 low priority items that have not been tested:
1. Using large HDDs (> 2TB) with this u-boot. It should work with both SATA and USB HDD enclosure/adapter.
Note: when using USB HDD, the disk should be formatted with the interface as intended usage (with the enclosure/adapter). IOW, a large disk formatted in the SATA slot sometime has problem in USB enclosure/adapter.
2. Netconsole. This might be problematic, so don't spend too much time on it. I saw some problem in testing other 2021.10 u-boots, and need to investigate.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 04:29PM |
Registered: 7 years ago Posts: 366 |
For large HDDs, I guess there will be no problem. I used 3TB & 4TB SATA in goflex home with the 2017 uboot and debian, no problem. I don't think there will be any problem with the 2021 version here.
For netconsole, I did not test it yet since I dug a hole in the box and kept the uart wires. :P
I always prefer wired version. :P
For netconsole, I did not test it yet since I dug a hole in the box and kept the uart wires. :P
I always prefer wired version. :P
|
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 04:59PM |
Admin Registered: 13 years ago Posts: 18,549 |
David,
> For large HDDs, I guess there will be no problem.
> I used 3TB & 4TB SATA in goflex home with the 2017
> uboot and debian, no problem. I don't think there
> will be any problem with the 2021 version here.
I don't expect to be problem (I already tested it on a few Kirkwood boxes). There were substantial USB and SATA-releated code changes from 2017.07 to 2021.10, so I do regression test for each board anyway when there is a convenient time to do it. But true, it's not a priority.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> For large HDDs, I guess there will be no problem.
> I used 3TB & 4TB SATA in goflex home with the 2017
> uboot and debian, no problem. I don't think there
> will be any problem with the 2021 version here.
I don't expect to be problem (I already tested it on a few Kirkwood boxes). There were substantial USB and SATA-releated code changes from 2017.07 to 2021.10, so I do regression test for each board anyway when there is a convenient time to do it. But true, it's not a priority.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 10, 2022 09:30AM |
Registered: 7 years ago Posts: 366 |
Netconsole seems working.
On serial port
Now go to netconsole
On serial port
U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 SoC: Kirkwood 88F6281_A1 Model: Ctera C200 V1 DRAM: 512 MiB NAND: 256 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000 88E1116 Initialized on ethernet-controller@72000 ethernet-controller@72000 Waiting for PHY auto negotiation to complete....... done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive
Now go to netconsole
C:\Documents and Settings\Home\Desktop\ncat-portable-5.59BETA1>ncat -l -u -p 666
6
U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1
gcc (Debian 10.2.1-6) 10.2.1 20210110
GNU ld (GNU Binutils for Debian) 2.35.2
Hit any key to stop autoboot: 2
0
C200_V1>boot
boot
Initializing devices...
starting USB...
Bus ehci@50000: USB EHCI 1.00
scanning bus ehci@50000 for devices...
Use USB retry period from the environment: 15 second(s)
3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Unknown command 'ide' - try 'help'
Loading envs from usb 0...
Failed to load '/boot/uEnv.txt'
Loading envs from usb 1...
Couldn't find partition usb 1:1
Can't set block device
Loading envs from usb 2...
Couldn't find partition usb 2:1
Can't set block device
Loading envs from usb 3...
Couldn't find partition usb 3:1
Can't set block device
Loading envs from ide 0...
Couldn't find partition ide 0:1
Can't set block device
Loading envs from ide 1...
Couldn't find partition ide 1:1
Can't set block device
Loading envs from ide 2...
Couldn't find partition ide 2:1
Can't set block device
Loading envs from ide 3...
Couldn't find partition ide 3:1
Can't set block device
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 9 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5576016 bytes read in 315 ms (16.9 MiB/s)
loading uInitrd ...
9582895 bytes read in 528 ms (17.3 MiB/s)
loading DTB /boot/dts/kirkwood-c200-v1.dtb ...
12173 bytes read in 13 ms (914.1 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.9.12-kirkwood-tld-1
Created: 2021-11-11 15:06:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5575952 Bytes = 5.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.9.12-kirkwood-tld-1
Created: 2021-11-11 15:06:26 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9582831 Bytes = 9.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Starting kernel ...
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 09:42AM |
Registered: 7 years ago Posts: 366 |
Wait... there's problem... it did not finish booting... nothing on serial console now... also, I can not ssh into it. (the ready light was not on).
Here's my env.
Anyway, not a big problem.... I have the serial cable...
Edited 1 time(s). Last edit at 01/10/2022 09:43AM by daviddyer.
Here's my env.
Anyway, not a big problem.... I have the serial cable...
C200_V1>printenv printenv bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then boo tm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_a ddr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi ; sleep 3 bootdelay=10 bootdev=usb device=0:1 devices=usb ide disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-c200-v1.dtb ethact=ethernet-controller@72000 ethaddr=00:25:25:00:6d:f2 fdtcontroladdr=1fb53f00 if_netconsole=ping $serverip ipaddr=192.168.7.248 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $d tb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /b oot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /bo ot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi) nc_ready=1 ncip=192.168.7.4 partition=nand0,2 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_ netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices ; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for di sknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.7.4 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; se tenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; se tenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $device s; do run init_$devtype; done uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_t ype $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo . .. envs loaded; fi usb_ready_retry=15 ver=U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 Environment size: 3043/131068 bytes C200_V1>boot
Edited 1 time(s). Last edit at 01/10/2022 09:43AM by daviddyer.
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 09:50AM |
Registered: 7 years ago Posts: 366 |
Disabled preboot in nc and everything is back to normal. :-)
C:\Documents and Settings\Home\Desktop\ncat-portable-5.59BETA1>ncat -l -u -p 666 6 U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 gcc (Debian 10.2.1-6) 10.2.1 20210110 GNU ld (GNU Binutils for Debian) 2.35.2 Hit any key to stop autoboot: 6 0 C200_V1>printenv preboot printenv preboot preboot=run preboot_nc C200_V1>setenv preboot setenv preboot C200_V1>saveenv saveenv Saving Environment to NAND... Erasing NAND... Erasing at 0xc0000 -- 100% complete. Writing to NAND... OK OK C200_V1>reset reset resetting ...
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 12:28PM |
Registered: 7 years ago Posts: 366 |
4TB seems OK.
Bootlog.
Bootlog.
U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1
SoC: Kirkwood 88F6281_A1
Model: Ctera C200 V1
DRAM: 512 MiB
NAND: 256 MiB
MMC:
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
Net: eth0: ethernet-controller@72000
88E1116 Initialized on ethernet-controller@72000
Hit any key to stop autoboot: 0
Initializing devices...
starting USB...
Bus ehci@50000: USB EHCI 1.00
scanning bus ehci@50000 for devices...
Use USB retry period from the environment: 15 second(s)
3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Unknown command 'ide' - try 'help'
Loading envs from usb 0...
Failed to load '/boot/uEnv.txt'
Loading envs from usb 1...
Couldn't find partition usb 1:1
Can't set block device
Loading envs from usb 2...
Couldn't find partition usb 2:1
Can't set block device
Loading envs from usb 3...
Couldn't find partition usb 3:1
Can't set block device
Loading envs from ide 0...
Couldn't find partition ide 0:1
Can't set block device
Loading envs from ide 1...
Couldn't find partition ide 1:1
Can't set block device
Loading envs from ide 2...
Couldn't find partition ide 2:1
Can't set block device
Loading envs from ide 3...
Couldn't find partition ide 3:1
Can't set block device
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 10 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5576016 bytes read in 315 ms (16.9 MiB/s)
loading uInitrd ...
9582895 bytes read in 528 ms (17.3 MiB/s)
loading DTB /boot/dts/kirkwood-c200-v1.dtb ...
12173 bytes read in 13 ms (914.1 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.9.12-kirkwood-tld-1
Created: 2021-11-11 15:06:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5575952 Bytes = 5.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.9.12-kirkwood-tld-1
Created: 2021-11-11 15:06:26 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9582831 Bytes = 9.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image
Loading Ramdisk to 1f22f000, end 1fb528ef ... OK
Loading Device Tree to 1f229000, end 1f22ef8c ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.9.12-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Ctera C200 V1
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 492516K/524288K available (10240K kernel code, 1096K rwdata, 4144K rodata, 1024K init, 316K bss, 31772K reserved, 0K cma-reserved)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x790 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Rude variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000054][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.000845][ T0] Console: colour dummy device 80x30
[ 0.000900][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.000929][ T0] pid_max: default: 32768 minimum: 301
[ 0.001349][ T0] LSM: Security Framework initializing
[ 0.001503][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001532][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002909][ T0] CPU: Testing write buffer coherency: ok
[ 0.004769][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.005077][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.005394][ T1] rcu: Hierarchical SRCU implementation.
[ 0.006708][ T1] devtmpfs: initialized
[ 0.013693][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.013733][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.014009][ T1] xor: measuring software checksum speed
[ 0.110120][ T1] arm4regs : 1088.800 MB/sec
[ 0.210078][ T1] 8regs : 654.000 MB/sec
[ 0.310081][ T1] 32regs : 950.800 MB/sec
[ 0.310102][ T1] xor: using function: arm4regs (1088.800 MB/sec)
[ 0.310127][ T1] prandom: seed boundary self test passed
[ 0.314306][ T1] prandom: 100 self tests passed
[ 0.314319][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.315868][ T1] NET: Registered protocol family 16
[ 0.316677][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.317731][ T1] audit: initializing netlink subsys (disabled)
[ 0.319136][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.319497][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1
[ 0.319634][ T1] cpuidle: using governor ladder
[ 0.319719][ T1] cpuidle: using governor menu
[ 0.320272][ T1] Feroceon L2: Enabling L2
[ 0.320324][ T1] Feroceon L2: Cache support initialised.
[ 0.336598][ T1] No ATAGs?
[ 2.560060][ C0] random: fast init done
[ 5.410422][ T1] raid6: int32x8 gen() 109 MB/s
[ 5.580180][ T1] raid6: int32x8 xor() 69 MB/s
[ 5.750253][ T1] raid6: int32x4 gen() 110 MB/s
[ 5.920154][ T1] raid6: int32x4 xor() 72 MB/s
[ 6.090243][ T1] raid6: int32x2 gen() 144 MB/s
[ 6.260187][ T1] raid6: int32x2 xor() 85 MB/s
[ 6.430155][ T1] raid6: int32x1 gen() 98 MB/s
[ 6.600167][ T1] raid6: int32x1 xor() 59 MB/s
[ 6.600179][ T1] raid6: using algorithm int32x2 gen() 144 MB/s
[ 6.600188][ T1] raid6: .... xor() 85 MB/s, rmw enabled
[ 6.600198][ T1] raid6: using intx1 recovery algorithm
[ 6.600461][ T1] vgaarb: loaded
[ 6.601033][ T1] SCSI subsystem initialized
[ 6.601555][ T1] usbcore: registered new interface driver usbfs
[ 6.601635][ T1] usbcore: registered new interface driver hub
[ 6.601726][ T1] usbcore: registered new device driver usb
[ 6.601955][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 6.601968][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 6.601997][ T1] PTP clock support registered
[ 6.603637][ T1] clocksource: Switched to clocksource orion_clocksource
[ 8.142998][ T1] VFS: Disk quotas dquot_6.6.0
[ 8.143106][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.154163][ T1] NET: Registered protocol family 2
[ 8.155037][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 8.155087][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 8.155157][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 8.155211][ T1] TCP: Hash tables configured (established 4096 bind 4096)
[ 8.155440][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 8.155509][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 8.155541][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 8.155764][ T1] NET: Registered protocol family 1
[ 8.156526][ T1] RPC: Registered named UNIX socket transport module.
[ 8.156540][ T1] RPC: Registered udp transport module.
[ 8.156549][ T1] RPC: Registered tcp transport module.
[ 8.156559][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 8.156574][ T1] PCI: CLS 0 bytes, default 32
[ 8.156892][ T1] Trying to unpack rootfs image as initramfs...
[ 8.996238][ T1] Freeing initrd memory: 9360K
[ 8.996414][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 9.007217][ T1] Initialise system trusted keyrings
[ 9.007276][ T1] Key type blacklist registered
[ 9.007501][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 9.007612][ T1] zbud: loaded
[ 9.009074][ T1] NFS: Registering the id_resolver key type
[ 9.009106][ T1] Key type id_resolver registered
[ 9.009117][ T1] Key type id_legacy registered
[ 9.009160][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 9.009180][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 9.009474][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 9.009998][ T1] fuse: init (API version 7.31)
[ 9.010397][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 9.010610][ T1] orangefs_init: module version upstream loaded
[ 9.010624][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 9.115431][ T1] async_tx: api initialized (async)
[ 9.115457][ T1] Key type asymmetric registered
[ 9.115467][ T1] Asymmetric key parser 'x509' registered
[ 9.115526][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 9.115639][ T1] io scheduler bfq registered
[ 9.314334][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 9.316317][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 9.316385][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 9.316425][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 9.316451][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 9.316754][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 9.316778][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 9.316799][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 9.316815][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 9.316830][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 9.316969][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 9.317003][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 9.318543][ T1] PCI: bus0: Fast back to back transfers disabled
[ 9.318573][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 9.319842][ T1] PCI: bus1: Fast back to back transfers enabled
[ 9.319869][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 9.320078][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref]
[ 9.320097][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 9.320792][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 9.384694][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 9.387352][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 9.444679][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 9.447594][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 9.449023][ T1] printk: console [ttyS0] disabled
[ 9.449116][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[ 10.399424][ T1] printk: console [ttyS0] enabled
[ 10.413086][ T1] loop: module loaded
[ 10.417803][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 10.427360][ T1] scsi host0: sata_mv
[ 10.431901][ T1] scsi host1: sata_mv
[ 10.436095][ T1] ata1: SATA max UDMA/133 irq 32
[ 10.440915][ T1] ata2: SATA max UDMA/133 irq 32
[ 10.447062][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[ 10.454238][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit
[ 10.459575][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 10.467957][ T1] Scanning device for bad blocks
[ 10.525167][ T1] Bad eraseblock 490 at 0x000003d40000
[ 10.538453][ T1] Bad eraseblock 565 at 0x0000046a0000
[ 10.567435][ T1] Bad eraseblock 787 at 0x000006260000
[ 10.579677][ T1] Bad eraseblock 852 at 0x000006a80000
[ 10.602454][ T1] Bad eraseblock 1016 at 0x000007f00000
[ 10.669601][ T1] Bad eraseblock 1595 at 0x00000c760000
[ 10.696967][ T1] Bad eraseblock 1800 at 0x00000e100000
[ 10.704406][ T1] Bad eraseblock 1819 at 0x00000e360000
[ 10.713659][ T1] Bad eraseblock 1855 at 0x00000e7e0000
[ 10.739619][ T1] 2 cmdlinepart partitions found on MTD device orion_nand
[ 10.746653][ T1] Creating 2 MTD partitions on "orion_nand":
[ 10.752559][ T1] 0x000000000000-0x000000100000 : "u-boot"
[ 10.759765][ T1] 0x000000100000-0x000010000000 : "ubi"
[ 10.768403][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 10.777094][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 10.788906][ T1] libphy: Fixed MDIO Bus: probed
[ 10.795088][ T1] libphy: orion_mdio_bus: probed
[ 10.816849][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 10.943689][ T88] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 10.953016][ T88] ata1.00: ATA-10: WDC WD40EZAZ-00SF3B0, 80.00A80, max UDMA/133
[ 10.960568][ T88] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 10.970633][ T88] ata1.00: configured for UDMA/133
[ 10.986190][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD40EZAZ-00S 0A80 PQ: 0 ANSI: 5
[ 10.996435][ T92] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 11.005442][ T92] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 11.011520][ T92] sd 0:0:0:0: [sda] Write Protect is off
[ 11.017239][ T92] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.032065][ T92] sd 0:0:0:0: [sda] Attached SCSI disk
[ 11.335277][ T90] ata2: SATA link down (SStatus 0 SControl F300)
[ 11.504537][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:25:00:6d:f2
[ 11.514191][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.521475][ T1] ehci-pci: EHCI PCI platform driver
[ 11.526728][ T1] ehci-orion: EHCI orion driver
[ 11.531679][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 11.537956][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 11.546554][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[ 11.573681][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 11.580713][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 11.589745][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.597721][ T1] usb usb1: Product: EHCI Host Controller
[ 11.603327][ T1] usb usb1: Manufacturer: Linux 5.9.12-kirkwood-tld-1 ehci_hcd
[ 11.610774][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 11.616923][ T1] hub 1-0:1.0: USB hub found
[ 11.621438][ T1] hub 1-0:1.0: 1 port detected
[ 11.627004][ T1] usbcore: registered new interface driver usb-storage
[ 11.634188][ T1] mousedev: PS/2 mouse device common for all mice
[ 11.640795][ T1] i2c /dev entries driver
[ 11.650910][ T1] rtc-s35390a 0-0030: registered as rtc0
[ 11.657572][ T1] rtc-s35390a 0-0030: setting system clock to 2022-01-10T18:15:29 UTC (1641838529)
[ 11.668087][ T1] device-mapper: uevent: version 1.0.3
[ 11.673795][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[ 11.683403][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 11.690772][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 11.698169][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 11.705655][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 11.712483][ T1] device-mapper: raid: Loading target version 1.15.1
[ 11.722167][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 11.728482][ T1] drop_monitor: Initializing network drop monitor service
[ 11.736116][ T1] NET: Registered protocol family 10
[ 11.742535][ T1] Segment Routing with IPv6
[ 11.746979][ T1] RPL Segment Routing with IPv6
[ 11.751789][ T1] NET: Registered protocol family 17
[ 11.757279][ T1] Key type dns_resolver registered
[ 11.762747][ T1] registered taskstats version 1
[ 11.767636][ T1] Loading compiled-in X.509 certificates
[ 11.773262][ T1] zswap: loaded using pool lzo/zbud
[ 11.778753][ T1] Key type ._fscrypt registered
[ 11.783478][ T1] Key type .fscrypt registered
[ 11.788193][ T1] Key type fscrypt-provisioning registered
[ 11.796118][ T1] Key type big_key registered
[ 11.831848][ T1] Key type encrypted registered
[ 11.842783][ T1] Freeing unused kernel memory: 1024K
[ 11.864583][ T1] Checked W+X mappings: passed, no W+X pages found
[ 11.870988][ T1] Run /init as init process
Loading, please wait...
[ 11.993760][ T99] usb 1-1: new high-speed USB device number 2 using orion-ehci
Starting version 241
[ 12.214341][ T99] usb 1-1: New USB device found, idVendor=0409, idProduct=005a, bcdDevice= 1.00
[ 12.223289][ T99] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 12.267513][ T99] hub 1-1:1.0: USB hub found
[ 12.277457][ T99] hub 1-1:1.0: 4 ports detected
[ 12.613741][ T99] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 12.729463][ T135] input: keys as /devices/platform/keys/input/input0
[ 12.774959][ T99] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5530, bcdDevice= 1.00
[ 12.793726][ T99] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 12.801778][ T99] usb 1-1.1: Product: Cruzer
[ 12.834503][ T99] usb 1-1.1: Manufacturer: SanDisk
[ 12.839501][ T99] usb 1-1.1: SerialNumber: 2005244411190D22FC1E
[ 12.858853][ T99] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 12.878486][ T99] scsi host2: usb-storage 1-1.1:1.0
[ 13.353340][ T130] usbcore: registered new interface driver uas
[ 13.924920][ T58] scsi 2:0:0:0: Direct-Access SanDisk Cruzer 1.02 PQ: 0 ANSI: 2
[ 13.939403][ T92] sd 2:0:0:0: [sdb] 7813120 512-byte logical blocks: (4.00 GB/3.73 GiB)
[ 13.953868][ T92] sd 2:0:0:0: [sdb] Write Protect is off
[ 13.960098][ T92] sd 2:0:0:0: [sdb] No Caching mode page found
[ 13.966283][ T92] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 13.987411][ T92] sdb: sdb1
[ 14.006613][ T92] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 25.316055][ T153] process '/usr/bin/fstype' started with executable stack
Begin: Will now check root file system ... fsck from util-linux 2.33.1
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sdb1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 30.497254][ T162] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem
[ 30.535316][ T162] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[ 33.790367][ T352] systemd-udevd[352]: Using default interface naming scheme 'v240'.
[ 33.903361][ T352] systemd-udevd[352]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 34.008241][ T370] orion_wdt: Initial timeout 21 sec
[ 34.319749][ T381] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 34.327266][ C0] random: crng init done
[ 34.414088][ T381] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 34.567472][ T353] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 34.775052][ T349] systemd-udevd[349]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[ 37.048839][ T570] EXT4-fs (sdb1): re-mounted. Opts: (null)
[....] Will now check root file system:fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sdb1
e2fsck 1.44.5 (15-Dec-2018)
rootfs: clean, 17950/244320 files, 520048/976384 blocks
. ok
[ 37.374751][ T596] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:25:25:00:6d:f2
Sending on LPF/eth0/00:25:25:00:6d:f2
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
[ 44.776008][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
DHCPOFFER of 192.168.7.248 from 192.168.7.1
DHCPREQUEST for 192.168.7.248 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.7.248 from 192.168.7.1
bound to 192.168.7.248 -- renewal in 40532 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
[ ok ] Setting sensors limits...done.
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1356 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1383 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 10 debian ttyS0
debian login: root
Password:
Last login: Mon Jan 10 07:47:07 PST 2022 on ttyS0
Linux debian 5.9.12-kirkwood-tld-1 #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020 armv5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~# df
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 12:46PM |
Registered: 7 years ago Posts: 366 |
Boot from 4TB SATA drive OK. (4TB in one partition, ext4)
U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1
SoC: Kirkwood 88F6281_A1
Model: Ctera C200 V1
DRAM: 512 MiB
NAND: 256 MiB
MMC:
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
Net: eth0: ethernet-controller@72000
88E1116 Initialized on ethernet-controller@72000
Hit any key to stop autoboot: 0
C200_V1>sata init
C200_V1>sata info
Device 0: Model: WDC WD40EZAZ-00SF3B0 Firm: 80.00A80 Ser#: WD-WX22D616S0PD
Type: Hard Disk
Supports 48-bit addressing
Capacity: 3815447.8 MB = 3726.0 GB (7814037168 x 512)
Failed to wait for completion on port 1
ATA operation timed out
Device 1: Model: Firm: Ser#:
Type: Hard Disk
Capacity: not available
C200_V1>ext2load sata 0 0x800000 /boot/uImage
5576016 bytes read in 89 ms (59.7 MiB/s)
C200_V1>ext2load sata 0 0x1100000 /boot/uInitrd
9582895 bytes read in 81 ms (112.8 MiB/s)
C200_V1>ext2load sata 0 0x1c00000 /boot/dts/kirkwood-c200-v1.dtb
12173 bytes read in 29 ms (409.2 KiB/s)
C200_V1>bootm 0x800000 0x1100000 0x1c00000
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.9.12-kirkwood-tld-1
Created: 2021-11-11 15:06:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5575952 Bytes = 5.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.9.12-kirkwood-tld-1
Created: 2021-11-11 15:06:26 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9582831 Bytes = 9.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image
Loading Ramdisk to 1f22f000, end 1fb528ef ... OK
Loading Device Tree to 1f229000, end 1f22ef8c ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.9.12-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Ctera C200 V1
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 492516K/524288K available (10240K kernel code, 1096K rwdata, 4144K rodata, 1024K init, 316K bss, 31772K reserved, 0K cma-reserved)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x790 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Rude variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000010][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000054][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.000848][ T0] Console: colour dummy device 80x30
[ 0.000904][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.000933][ T0] pid_max: default: 32768 minimum: 301
[ 0.001356][ T0] LSM: Security Framework initializing
[ 0.001512][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001543][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002928][ T0] CPU: Testing write buffer coherency: ok
[ 0.004788][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.005097][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.005414][ T1] rcu: Hierarchical SRCU implementation.
[ 0.006724][ T1] devtmpfs: initialized
[ 0.013706][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.013746][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.014016][ T1] xor: measuring software checksum speed
[ 0.110119][ T1] arm4regs : 1088.800 MB/sec
[ 0.210077][ T1] 8regs : 654.000 MB/sec
[ 0.310077][ T1] 32regs : 950.800 MB/sec
[ 0.310099][ T1] xor: using function: arm4regs (1088.800 MB/sec)
[ 0.310123][ T1] prandom: seed boundary self test passed
[ 0.314302][ T1] prandom: 100 self tests passed
[ 0.314314][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.315854][ T1] NET: Registered protocol family 16
[ 0.316664][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.317717][ T1] audit: initializing netlink subsys (disabled)
[ 0.319127][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.319485][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1
[ 0.319624][ T1] cpuidle: using governor ladder
[ 0.319709][ T1] cpuidle: using governor menu
[ 0.320260][ T1] Feroceon L2: Enabling L2
[ 0.320311][ T1] Feroceon L2: Cache support initialised.
[ 0.336589][ T1] No ATAGs?
[ 2.560059][ C0] random: fast init done
[ 5.410310][ T1] raid6: int32x8 gen() 109 MB/s
[ 5.580231][ T1] raid6: int32x8 xor() 69 MB/s
[ 5.750201][ T1] raid6: int32x4 gen() 109 MB/s
[ 5.920148][ T1] raid6: int32x4 xor() 72 MB/s
[ 6.090187][ T1] raid6: int32x2 gen() 140 MB/s
[ 6.260143][ T1] raid6: int32x2 xor() 85 MB/s
[ 6.430227][ T1] raid6: int32x1 gen() 98 MB/s
[ 6.600194][ T1] raid6: int32x1 xor() 60 MB/s
[ 6.600207][ T1] raid6: using algorithm int32x2 gen() 140 MB/s
[ 6.600216][ T1] raid6: .... xor() 85 MB/s, rmw enabled
[ 6.600225][ T1] raid6: using intx1 recovery algorithm
[ 6.600486][ T1] vgaarb: loaded
[ 6.601068][ T1] SCSI subsystem initialized
[ 6.601596][ T1] usbcore: registered new interface driver usbfs
[ 6.601679][ T1] usbcore: registered new interface driver hub
[ 6.601769][ T1] usbcore: registered new device driver usb
[ 6.602000][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 6.602013][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 6.602043][ T1] PTP clock support registered
[ 6.603685][ T1] clocksource: Switched to clocksource orion_clocksource
[ 8.143044][ T1] VFS: Disk quotas dquot_6.6.0
[ 8.143151][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.154185][ T1] NET: Registered protocol family 2
[ 8.155064][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 8.155114][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 8.155185][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 8.155238][ T1] TCP: Hash tables configured (established 4096 bind 4096)
[ 8.155461][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 8.155529][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 8.155561][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 8.155786][ T1] NET: Registered protocol family 1
[ 8.156553][ T1] RPC: Registered named UNIX socket transport module.
[ 8.156567][ T1] RPC: Registered udp transport module.
[ 8.156577][ T1] RPC: Registered tcp transport module.
[ 8.156586][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 8.156602][ T1] PCI: CLS 0 bytes, default 32
[ 8.156923][ T1] Trying to unpack rootfs image as initramfs...
[ 8.996282][ T1] Freeing initrd memory: 9360K
[ 8.996457][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 9.007264][ T1] Initialise system trusted keyrings
[ 9.007324][ T1] Key type blacklist registered
[ 9.007557][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 9.007665][ T1] zbud: loaded
[ 9.009135][ T1] NFS: Registering the id_resolver key type
[ 9.009170][ T1] Key type id_resolver registered
[ 9.009181][ T1] Key type id_legacy registered
[ 9.009227][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 9.009247][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 9.009542][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 9.010066][ T1] fuse: init (API version 7.31)
[ 9.010465][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 9.010678][ T1] orangefs_init: module version upstream loaded
[ 9.010692][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 9.111546][ T1] async_tx: api initialized (async)
[ 9.111571][ T1] Key type asymmetric registered
[ 9.111582][ T1] Asymmetric key parser 'x509' registered
[ 9.111642][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 9.111758][ T1] io scheduler bfq registered
[ 9.310451][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 9.312431][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 9.312500][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 9.312540][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 9.312567][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 9.312870][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 9.312893][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 9.312913][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 9.312929][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 9.312944][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 9.313083][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 9.313117][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 9.314711][ T1] PCI: bus0: Fast back to back transfers disabled
[ 9.314742][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 9.316018][ T1] PCI: bus1: Fast back to back transfers enabled
[ 9.316047][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 9.316255][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref]
[ 9.316274][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 9.316973][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 9.374746][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 9.377407][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 9.434732][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 9.437629][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 9.439058][ T1] printk: console [ttyS0] disabled
[ 9.439152][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[ 10.389454][ T1] printk: console [ttyS0] enabled
[ 10.403123][ T1] loop: module loaded
[ 10.407841][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 10.417410][ T1] scsi host0: sata_mv
[ 10.421956][ T1] scsi host1: sata_mv
[ 10.426145][ T1] ata1: SATA max UDMA/133 irq 32
[ 10.430962][ T1] ata2: SATA max UDMA/133 irq 32
[ 10.437110][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[ 10.444285][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit
[ 10.449623][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 10.458005][ T1] Scanning device for bad blocks
[ 10.515159][ T1] Bad eraseblock 490 at 0x000003d40000
[ 10.528448][ T1] Bad eraseblock 565 at 0x0000046a0000
[ 10.557433][ T1] Bad eraseblock 787 at 0x000006260000
[ 10.569663][ T1] Bad eraseblock 852 at 0x000006a80000
[ 10.592441][ T1] Bad eraseblock 1016 at 0x000007f00000
[ 10.659596][ T1] Bad eraseblock 1595 at 0x00000c760000
[ 10.686946][ T1] Bad eraseblock 1800 at 0x00000e100000
[ 10.694370][ T1] Bad eraseblock 1819 at 0x00000e360000
[ 10.703609][ T1] Bad eraseblock 1855 at 0x00000e7e0000
[ 10.729587][ T1] 2 cmdlinepart partitions found on MTD device orion_nand
[ 10.736618][ T1] Creating 2 MTD partitions on "orion_nand":
[ 10.742526][ T1] 0x000000000000-0x000000100000 : "u-boot"
[ 10.749729][ T1] 0x000000100000-0x000010000000 : "ubi"
[ 10.758366][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 10.767054][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 10.778860][ T1] libphy: Fixed MDIO Bus: probed
[ 10.785030][ T1] libphy: orion_mdio_bus: probed
[ 10.807101][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 10.933737][ T88] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 10.943064][ T88] ata1.00: ATA-10: WDC WD40EZAZ-00SF3B0, 80.00A80, max UDMA/133
[ 10.950615][ T88] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 10.960682][ T88] ata1.00: configured for UDMA/133
[ 10.976239][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD40EZAZ-00S 0A80 PQ: 0 ANSI: 5
[ 10.986484][ T92] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 10.995491][ T92] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 11.001567][ T92] sd 0:0:0:0: [sda] Write Protect is off
[ 11.007290][ T92] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.069262][ T92] sda: sda1
[ 11.074269][ T92] sd 0:0:0:0: [sda] Attached SCSI disk
[ 11.325326][ T90] ata2: SATA link down (SStatus 0 SControl F300)
[ 11.494586][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:25:00:6d:f2
[ 11.504225][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.511505][ T1] ehci-pci: EHCI PCI platform driver
[ 11.516759][ T1] ehci-orion: EHCI orion driver
[ 11.521701][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 11.527977][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 11.536569][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[ 11.563730][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 11.570748][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 11.579782][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.587760][ T1] usb usb1: Product: EHCI Host Controller
[ 11.593365][ T1] usb usb1: Manufacturer: Linux 5.9.12-kirkwood-tld-1 ehci_hcd
[ 11.600813][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 11.606959][ T1] hub 1-0:1.0: USB hub found
[ 11.611490][ T1] hub 1-0:1.0: 1 port detected
[ 11.617064][ T1] usbcore: registered new interface driver usb-storage
[ 11.624260][ T1] mousedev: PS/2 mouse device common for all mice
[ 11.630853][ T1] i2c /dev entries driver
[ 11.640993][ T1] rtc-s35390a 0-0030: registered as rtc0
[ 11.647650][ T1] rtc-s35390a 0-0030: setting system clock to 2022-01-10T18:44:54 UTC (1641840294)
[ 11.658174][ T1] device-mapper: uevent: version 1.0.3
[ 11.663861][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[ 11.673493][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 11.680862][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 11.688262][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 11.695729][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 11.702557][ T1] device-mapper: raid: Loading target version 1.15.1
[ 11.712283][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 11.718589][ T1] drop_monitor: Initializing network drop monitor service
[ 11.726215][ T1] NET: Registered protocol family 10
[ 11.732631][ T1] Segment Routing with IPv6
[ 11.737078][ T1] RPL Segment Routing with IPv6
[ 11.741888][ T1] NET: Registered protocol family 17
[ 11.747388][ T1] Key type dns_resolver registered
[ 11.752856][ T1] registered taskstats version 1
[ 11.757747][ T1] Loading compiled-in X.509 certificates
[ 11.763366][ T1] zswap: loaded using pool lzo/zbud
[ 11.768857][ T1] Key type ._fscrypt registered
[ 11.773587][ T1] Key type .fscrypt registered
[ 11.778302][ T1] Key type fscrypt-provisioning registered
[ 11.786198][ T1] Key type big_key registered
[ 11.821829][ T1] Key type encrypted registered
[ 11.832767][ T1] Freeing unused kernel memory: 1024K
[ 11.854630][ T1] Checked W+X mappings: passed, no W+X pages found
[ 11.861036][ T1] Run /init as init process
Loading, please wait...
[ 11.983816][ T99] usb 1-1: new high-speed USB device number 2 using orion-ehci
Starting version 241
[ 12.204356][ T99] usb 1-1: New USB device found, idVendor=0409, idProduct=005a, bcdDevice= 1.00
[ 12.213299][ T99] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 12.257779][ T99] hub 1-1:1.0: USB hub found
[ 12.267271][ T99] hub 1-1:1.0: 4 ports detected
[ 12.749469][ T132] input: keys as /devices/platform/keys/input/input0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 24.636689][ T148] process '/usr/bin/fstype' started with executable stack
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1
rootfs: clean, 19392/244195328 files, 15865769/976754385 blocks
done.
[ 26.669402][ T158] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[....] Synthesizing the initial hotplug events (devices)...[ 30.555628][ C0] random: crng init done
done.
[....] Waiting for /dev to be fully populated...[ 30.776864][ T365] systemd-udevd[365]: Using default interface naming scheme 'v240'.
[ 30.895868][ T365] systemd-udevd[365]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.081746][ T377] orion_wdt: Initial timeout 21 sec
[ 31.181706][ T347] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 31.566375][ T348] systemd-udevd[348]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.658656][ T375] marvell-cesa f1030000.crypto: CESA device successfully registered
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[ 33.944332][ T566] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[info] Loading kernel module lm63.
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:25:25:00:6d:f2
Sending on LPF/eth0/00:25:25:00:6d:f2
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
[ 41.657806][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPOFFER of 192.168.7.248 from 192.168.7.1
DHCPREQUEST for 192.168.7.248 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.7.248 from 192.168.7.1
bound to 192.168.7.248 -- renewal in 32825 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
[ ok ] Setting sensors limits...done.
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1357 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1384 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[warn] Not starting fancontrol; run pwmconfig first. ... (warning).
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 10 debian ttyS0
debian login: root
Password:
Last login: Mon Jan 10 10:36:47 PST 2022 on ttyS0
Linux debian 5.9.12-kirkwood-tld-1 #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020 armv5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~# df
Filesystem 1K-blocks Used Available Use% Mounted on
udev 246256 0 246256 0% /dev
tmpfs 50292 152 50140 1% /run
/dev/sda1 3844640564 1086104 3843538076 1% /
tmpfs 5120 0 5120 0% /run/lock
tmpfs 100580 0 100580 0% /dev/shm
tmpfs 251448 0 251448 0% /tmp
root@debian:~# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.7.248 netmask 255.255.255.0 broadcast 192.168.7.255
ether 00:25:25:00:6d:f2 txqueuelen 1000 (Ethernet)
RX packets 17 bytes 2141 (2.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 16 bytes 2004 (1.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 35
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 1000 (Local Loopback)
RX packets 2 bytes 140 (140.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2 bytes 140 (140.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
root@debian:~#
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 01:01PM |
Registered: 7 years ago Posts: 366 |
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 04:14PM |
Admin Registered: 13 years ago Posts: 18,549 |
> Disabled preboot in nc and everything is back to
> normal. :-)
OK! this is weird, I need to investigate further. There might be some changes in 2021.10 netconsole code that messed up the network.
And I need to post the new default envs too.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> normal. :-)
OK! this is weird, I need to investigate further. There might be some changes in 2021.10 netconsole code that messed up the network.
And I need to post the new default envs too.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 04:17PM |
Admin Registered: 13 years ago Posts: 18,549 |
BTW,
The mtdparts should be (we want to use the same size as stock u-boot does):
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
The mtdparts should be (we want to use the same size as stock u-boot does):
mtdparts=mtdparts=orion_nand:2M(u-boot),-(ubi)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 07:26PM |
Registered: 7 years ago Posts: 366 |
mtdparts:
I think that's not a big deal. For me, I will never go back to the old firmware. Even if we install openwrt (as rescue), I guess we won't be able to get back since we will overwrite a lot of things with our definition of mtdparts... The original OpenWrt rootfs partition use unused space after stock firmware.
I think that's not a big deal. For me, I will never go back to the old firmware. Even if we install openwrt (as rescue), I guess we won't be able to get back since we will overwrite a lot of things with our definition of mtdparts... The original OpenWrt rootfs partition use unused space after stock firmware.
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 11:30PM |
Admin Registered: 13 years ago Posts: 18,549 |
David,
There are many good reasons to keep u-boot partition at 2MB (similar to what I had for the Pogo V4). That's will be part of the u-boot installation instruction.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
There are many good reasons to keep u-boot partition at 2MB (similar to what I had for the Pogo V4). That's will be part of the u-boot installation instruction.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 11, 2022 12:48PM |
Registered: 7 years ago Posts: 366 |
