Unable to Boot Debian on Dockstar

All,

Installed the latest UBoot following the instructions listed here, http://projects.doozan.com/uboot/. However, fw_printenv and fw_setenv were installed in /usr/sbin instead of /usr/bin as stated in the documentation. An attempt to reinstall confirmed I have the latest UBoot installed.

## Valid uBoot detected: [dockstar davygravy-2012-02-12-current]

I installed Debian Squeeze successfully following the instructions listed here, http://projects.doozan.com/debian/. On a reboot, the LED glows green before accessing the USB drive. After that it changes to orange. It access the USB drive on more time before it turns green and returns to the Pogoplug prompt.

I attempted a netconsole debug session, but didn't receive any data on the listener. Below is the output of fw_printenv

Pogoplug:/usr/bin$ /usr/sbin/fw_printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootfstype=ext2
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ethaddr=00:10:75:1A:01:55
arcNumber=2097

There was nothing of note in /var/log on the USB device and I run it through fsck with no errors on a separate machine.

What should be my next steps to determining the issue?

I was able to netconsole working and noted it was complaining about no uImage as noted here, http://forum.doozan.com/read.php?2,11396.

I created the images on my Crunchbang machine and copied the files over. From there I received the following from netconsole

Patricks-MacBook-Pro:062513 pmcdonald$ sudo nc -lu 6666

U-Boot 2011.12 (Feb 12 2012 - 21:33:07)
Seagate FreeAgent DockStar
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000020000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 475 MiB
UBI: number of good PEBs: 3794
UBI: number of bad PEBs: 6
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 3753
UBI: total number of reserved PEBs: 41
UBI: number of PEBs reserved for bad PEB handling: 37
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1437200 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
4535246 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32-5-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1437136 Bytes = 1.4 MiB
Load Address: 00000000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-2.6.32-5-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4535182 Bytes = 4.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

However I don't see the device on my network. What should be the next steps for me to investigate?

Thanks,
Patrick

I'v had same problem.

check this thread
http://forum.doozan.com/read.php?2,13053



Edited 1 time(s). Last edit at 07/23/2013 06:18AM by garyang.